doc/haproxy-en.txt

                           -------------------
                             H A - P r o x y
                            Reference  Manual
                           -------------------
                              version 1.2.13
                              willy tarreau
                                2006/05/13

============
| Abstract |
============

HA-Proxy is a TCP/HTTP reverse proxy which is particularly suited for high
availability environments. Indeed, it can :
  - route HTTP requests depending on statically assigned cookies ;
  - spread the load among several servers while assuring server persistence
    through the use of HTTP cookies ;
  - switch to backup servers in the event a main one fails ;
  - accept connections to special ports dedicated to service monitoring ;
  - stop accepting connections without breaking existing ones ;
  - add/modify/delete HTTP headers both ways ;
  - block requests matching a particular pattern ;
  - hold clients to the right application server depending on application
    cookies
  - report detailed status as HTML pages to authenticated users from an URI
    intercepted from the application.

It needs very little resource. Its event-driven architecture allows it to easily
handle thousands of simultaneous connections on hundreds of instances without
risking the system's stability.

====================
| Start parameters |
====================

There are only a few command line options :

    -f <configuration file>
    -n <high limit for the total number of simultaneous connections>
       = 'maxconn' in 'global' section
    -N <high limit for the per-listener number of simultaneous connections>
       = 'maxconn' in 'listen' or 'default' sections
    -d starts in foregreound with debugging mode enabled
    -D starts in daemon mode
    -q disable messages on output
    -V displays messages on output even when -q or 'quiet' are specified.
    -c only checks config file and exits with code 0 if no error was found, or
       exits with code 1 if a syntax error was found.
    -p <pidfile> asks the process to write down each of its children's
       pids to this file in daemon mode.
    -sf specifies a list of pids to send a FINISH signal to after startup.
    -st specifies a list of pids to send a TERMINATE signal to after startup.
    -s shows statistics (only if compiled in)
    -l shows even more statistics (implies '-s')
    -de disables use of epoll()
    -dp disables use of poll()
    -db disables background mode (stays in foreground, useful for debugging)
    -m <megs> enforces a memory usage limit to a maximum of <megs> megabytes.

The maximal number of connections per proxy instance is used as the default
parameter for each instance for which the 'maxconn' paramter is not set in the
'listen' section.

The maximal number of total connections limits the number of connections used by
the whole process if the 'maxconn' parameter is not set in the 'global' section.

The debugging mode has the same effect as the 'debug' option in the 'global'
section. When the proxy runs in this mode, it dumps every connections,
disconnections, timestamps, and HTTP headers to stdout. This should NEVER
be used in an init script since it will prevent the system from starting up.

For debugging, the '-db' option is very useful as it temporarily disables
daemon mode and multi-process mode. The service can then be stopped by simply
pressing Ctrl-C, without having to edit the config nor run full debug.

Statistics are only available if compiled in with the 'STATTIME' option. It's
only used during code optimization phases, and will soon disappear.

The '-st' and '-sf' options are used for hot reconfiguration (see below).

======================
| Configuration file |
======================

Structure
=========

The configuration file parser ignores empty lines, spaces, tabs. Anything
between a sharp ('#') not following a backslash ('\'), and the end of a line
constitutes a comment and is ignored too.

The configuration file is segmented in sections. A section begins whenever
one of these 3 keywords are encountered :

  - 'global'
  - 'listen'
  - 'defaults'

Every parameter refer to the section beginning at the last one of these 3
keywords.


1) Global parameters
====================

Global parameters affect the whole process behaviour. They are all set in the
'global' section. There may be several 'global' sections if needed, but their
parameters will only be merged. Allowed parameters in 'global' section include
the following ones :

  - log <address> <facility> [max_level]
  - maxconn <number>
  - uid <user id>
  - gid <group id>
  - chroot <directory>
  - nbproc <number>
  - daemon
  - debug
  - noepoll
  - nopoll
  - quiet
  - pidfile <file>
  - ulimit-n <number>
  - stats


1.1) Event logging
------------------
Most events are logged : start, stop, servers going up and down, connections and
errors. Each event generates a syslog message which can be sent to up to 2
servers. The syntax is :

    log <ip_address> <facility> [max_level]

Connections are logged at level "info". Services initialization and servers
going up are logged at level "notice", termination signals are logged at
"warning", and definitive service termination, as well as loss of servers are
logged at level "alert". The optional parameter <max_level> specifies above
what level messages should be sent. Level can take one of these 8 values :

    emerg, alert, crit, err, warning, notice, info, debug

For backwards compatibility with versions 1.1.16 and earlier, the default level
value is "debug" if not specified.

Permitted facilities are :
    kern, user, mail, daemon, auth, syslog, lpr, news,
    uucp, cron, auth2, ftp, ntp, audit, alert, cron2,
    local0, local1, local2, local3, local4, local5, local6, local7

According to RFC3164, messages are truncated to 1024 bytes before being emitted.

Example :
---------
    global
        log 192.168.2.200 local3
        log 127.0.0.1     local4 notice


1.2) limiting the number of connections
---------------------------------------
It is possible and recommended to limit the global number of per-process
connections using the 'maxconn' global keyword. Since one connection includes
both a client and a server, it means that the max number of TCP sessions will
be about the double of this number. It's important to understand this when
trying to find best values for 'ulimit -n' before starting the proxy. To
anticipate the number of sockets needed, all these parameters must be counted :

  - 1 socket per incoming connection
  - 1 socket per outgoing connection
  - 1 socket per address/port/proxy tuple.
  - 1 socket per server being health-checked
  - 1 socket for all logs

In simple configurations where each proxy only listens one one address/port,
set the limit of file descriptors (ulimit -n) to
(2 * maxconn + nbproxies + nbservers + 1). Starting with versions 1.1.32/1.2.6,
it is now possible to set the limit in the configuration using the 'ulimit-n'
global keyword, provided the proxy is started as root. This puts an end to the
recurrent problem of ensuring that the system limits are adapted to the proxy
values. Note that these limits are per-process.

Example :
---------
    global
        maxconn 32000
        ulimit-n 65536


1.3) Drop of priviledges
------------------------
In order to reduce the risk and consequences of attacks, in the event where a
yet non-identified vulnerability would be successfully exploited, it's possible
to lower the process priviledges and even isolate it in a riskless directory.

In the 'global' section, the 'uid' parameter sets a numerical user identifier
which the process will switch to after binding its listening sockets. The value
'0', which normally represents the super-user, here indicates that the UID must
not change during startup. It's the default behaviour. The 'gid' parameter does
the same for the group identifier. It's particularly advised against use of
generic accounts such as 'nobody' because it has the same consequences as using
'root' if other services use them.

The 'chroot' parameter makes the process isolate itself in an empty directory
just before switching its UID. This type of isolation (chroot) can sometimes
be worked around on certain OS (Linux, Solaris), provided that the attacker
has gained 'root' priviledges and has the ability to use or create a directory.
For this reason, it's capital to use a dedicated directory and not to share one
between several services of different nature. To make isolation more resistant,
it's recommended to use an empty directory without any right, and to change the
UID of the process so that it cannot do anything there.

Note: in the event where such a vulnerability would be exploited, it's most
likely that first attempts would kill the process due to 'Segmentation Fault',
'Bus Error' or 'Illegal Instruction' signals. Eventhough it's true that
isolating the server reduces the risks of intrusion, it's sometimes useful to
find why a process dies, via the analysis of a 'core' file, although very rare
(the last bug of this sort was fixed in 1.1.9). For security reasons, most
systems disable the generation of core file when a process changes its UID. So
the two workarounds are either to start the process from a restricted user
account, which will not be able to chroot itself, or start it as root and not
change the UID. In both cases the core will be either in the start or the chroot
directories. Do not forget to allow core dumps prior to start the process :

# ulimit -c unlimited

Example :
---------

    global
        uid     30000
        gid     30000
        chroot  /var/chroot/haproxy


1.4) Startup modes
------------------
The service can start in several different modes :
  - foreground / background
  - quiet / normal / debug

The default mode is normal, foreground, which means that the program doesn't
return once started. NEVER EVER use this mode in a system startup script, or
the system won't boot. It needs to be started in background, so that it
returns immediately after forking. That's accomplished by the 'daemon' option
in the 'global' section, which is the equivalent of the '-D' command line
argument.

The '-db' command line argument overrides the 'daemon' and 'nbproc' global
options to make the process run in normal, foreground mode.

Moreover, certain alert messages are still sent to the standard output even
in 'daemon' mode. To make them disappear, simply add the 'quiet' option in the
'global' section. This option has no command-line equivalent.

Last, the 'debug' mode, enabled with the 'debug' option in the 'global' section,
and which is equivalent of the '-d' option, allows deep TCP/HTTP analysis, with
timestamped display of each connection, disconnection, and HTTP headers for both
ways. This mode is incompatible with 'daemon' and 'quiet' modes for obvious
reasons.


1.5) Increasing the overall processing power
--------------------------------------------
On multi-processor systems, it may seem to be a shame to use only one processor,
eventhough the load needed to saturate a recent processor is far above common
usage. Anyway, for very specific needs, the proxy can start several processes
between which the operating system will spread the incoming connections. The
number of processes is controlled by the 'nbproc' parameter in the 'global'
section. It defaults to 1, and obviously works only in 'daemon' mode. One
typical usage of this parameter has been to workaround the default per-process
file-descriptor limit that Solaris imposes to user processes.

Example :
---------

    global
        daemon
        quiet
        nbproc  2


1.6) Helping process management
-------------------------------
Haproxy now supports the notion of pidfile. If the '-p' command line argument,
or the 'pidfile' global option is followed with a file name, this file will be
removed, then filled with all children's pids, one per line (only in daemon
mode). This file is NOT within the chroot, which allows to work with a readonly
 chroot. It will be owned by the user starting the process, and will have
permissions 0644.

Example :
---------

    global
        daemon
        quiet
        nbproc  2
        pidfile /var/run/haproxy-private.pid

    # to stop only those processes among others :
    # kill $(</var/run/haproxy-private.pid)

    # to reload a new configuration with minimal service impact and without
    # breaking existing sessions :
    # haproxy -f haproxy.cfg -p $(</var/run/haproxy-private.pid) -st $(</var/run/haproxy-private.pid)

1.7) Polling mechanisms
-----------------------
Starting from version 1.2.5, haproxy supports the poll() and epoll() polling
mechanisms. On systems where select() is limited by FD_SETSIZE (like Solaris),
poll() can be an interesting alternative. Performance tests show that Solaris'
poll() performance does not decay as fast as the numbers of sockets increase,
making it a safe solution for high loads. However, Solaris already uses poll()
to emulate select(), so as long as the number of sockets has no reason to go
higher than FD_SETSIZE, poll() should not provide any better performance. On
Linux systems with the epoll() patch (or any 2.6 version), haproxy will use
epoll() which is extremely fast and non dependant on the number of sockets.
Tests have shown constant performance from 1 to 20000 simultaneous sessions.

Haproxy will use epoll() when available, and will fall back to poll(), then to
select(). However, if for any reason you need to disable epoll() or poll() (eg.
because of a bug or just to compare performance), two new global options have
been created for this matter : 'noepoll' and 'nopoll'.

Example :
---------

    global
        # use only select()
        noepoll
        nopoll

Note :
------
For the sake of configuration file portability, these options are accepted but
ignored if the poll() or epoll() mechanisms have not been enabled at compile
time.

To make debugging easier, the '-de' runtime argument disables epoll support and
the '-dp' argument disables poll support. They are respectively equivalent to
'noepoll' and 'nopoll'.


2) Declaration of a listening service
=====================================

Service sections start with the 'listen' keyword :

    listen <instance_name> [ <IP_address>:<port_range>[,...] ]

- <instance_name> is the name of the instance. This name will be reported in
  logs, so it is good to have it reflect the proxied service. No unicity test
  is done on this name, and it's not mandatory for it to be unique, but highly
  recommended.

- <IP_address> is the IP address the proxy binds to. Empty address, '*' and
  '0.0.0.0' all mean that the proxy listens to all valid addresses on the
  system.

- <port_range> is either a unique port, or a port range for which the proxy will
  accept connections for the IP address specified above. This range can be :
    - a numerical port (ex: '80')
    - a dash-delimited ports range explicitly stating the lower and upper bounds
      (ex: '2000-2100') which are included in the range.

  Particular care must be taken against port ranges, because every <addr:port>
  couple consumes one socket (=a file descriptor), so it's easy to eat lots of
  descriptors with a simple range. The <addr:port> couple must be used only once
  among all instances running on a same system. Please note that attaching to
  ports lower than 1024 need particular priviledges to start the program, which
  are independant of the 'uid' parameter.

- the <IP_address>:<port_range> couple may be repeated indefinitely to require
  the proxy to listen to other addresses and/or ports. To achieve this, simply
  separate them with a coma.

Examples :
---------
    listen http_proxy :80
    listen x11_proxy 127.0.0.1:6000-6009
    listen smtp_proxy 127.0.0.1:25,127.0.0.1:587
    listen ldap_proxy :389,:663

In the event that all addresses do not fit line width, it's preferable to
detach secondary addresses on other lines with the 'bind' keyword. If this
keyword is used, it's not even necessary to specify the first address on the
'listen' line, which sometimes makes multiple configuration handling easier :

    bind [ <IP_address>:<port_range>[,...] ]

Examples :
----------
    listen http_proxy
        bind :80,:443
        bind 10.0.0.1:10080,10.0.0.1:10443


2.1) Inhibiting a service
-------------------------
A service may be disabled for maintenance reasons, without needing to comment
out the whole section, simply by specifying the 'disabled' keyword in the
section to be disabled :

    listen smtp_proxy 0.0.0.0:25
        disabled

Note: the 'enabled' keyword allows to enable a service which has been disabled
      previously by a default configuration.


2.2) Modes of operation
-----------------------
A service can work in 3 different distinct modes :
  - TCP
  - HTTP
  - health

TCP mode
--------
In this mode, the service relays TCP connections as soon as they're established,
towards one or several servers. No processing is done on the stream. It's only
an association of source(addr:port) -> destination(addr:port). To use this mode,
you must specify 'mode tcp' in the 'listen' section. This is the default mode.

Example :
---------
    listen smtp_proxy 0.0.0.0:25
        mode tcp

HTTP mode
---------
In this mode, the service relays TCP connections towards one or several servers,
when it has enough informations to decide, which normally means that all HTTP
headers have been read. Some of them may be scanned for a cookie or a pattern
matching a regex. To use this mode, specify 'mode http' in the 'listen' section.

Example :
---------
    listen http_proxy 0.0.0.0:80
        mode http

Health-checking mode
--------------------
This mode provides a way for external components to check the proxy's health.
It is meant to be used with intelligent load-balancers which can use send/expect
scripts to check for all of their servers' availability. This one simply accepts
the connection, returns the word 'OK' and closes it. If the 'option httpchk' is
set, then the reply will be 'HTTP/1.0 200 OK' with no data, so that it can be
tested from a tool which supports HTTP health-checks. To enable it, simply
specify 'health' as the working mode :

Example :
---------
    # simple response : 'OK'
    listen health_check 0.0.0.0:60000
        mode health

    # HTTP response : 'HTTP/1.0 200 OK'
    listen http_health_check 0.0.0.0:60001
        mode health
        option httpchk

2.2.1 Monitoring
----------------
Versions 1.1.32 and 1.2.6 provide a new solution to check the proxy's
availability without perturbating the service. The 'monitor-net' keyword was
created to specify a network of equipments which CANNOT use the service for
anything but health-checks. This is particularly suited to TCP proxies, because
it prevents the proxy from relaying the monitor's connection to the remote
server.

When used with TCP, the connection is accepted then closed and nothing is
logged. This is enough for a front-end load-balancer to detect the service as
available.

When used with HTTP, the connection is accepted, nothing is logged, the
following response is sent, then the session is closed : "HTTP/1.0 200 OK".
This is normally enough for any front-end HTTP load-balancer to detect the
service as available too, both with TCP and HTTP checks.

Proxies using the "monitor-net" keyword can remove the "option dontlognull", as
it will make them log empty connections from hosts outside the monitoring
network.

Example :
---------

    listen tse-proxy
       bind :3389,:1494,:5900  # TSE, ICA and VNC at once.
       mode tcp
       balance roundrobin
       server tse-farm 192.168.1.10
       monitor-net 192.168.1.252/31   # L4 load-balancers on .252 and .253


2.3) Limiting the number of simultaneous connections
----------------------------------------------------
The 'maxconn' parameter allows a proxy to refuse connections above a certain
amount of simultaneous ones. When the limit is reached, it simply stops
listening, but the system may still be accepting them because of the back log
queue. These connections will be processed later when other ones have freed
some slots. This provides a serialization effect which helps very fragile
servers resist to high loads. See further for system limitations.

Example :
---------
    listen tiny_server 0.0.0.0:80
        maxconn 10


2.4) Soft stop
--------------
It is possible to stop services without breaking existing connections by the
sending of the SIGUSR1 signal to the process. All services are then put into
soft-stop state, which means that they will refuse to accept new connections,
except for those which have a non-zero value in the 'grace' parameter, in which
case they will still accept connections for the specified amount of time, in
milliseconds. This makes it possible to tell a load-balancer that the service
is failing, while still doing the job during the time it needs to detect it.

Note: active connections are never killed. In the worst case, the user will have
to wait for all of them to close or to time-out, or simply kill the process
normally (SIGTERM). The default 'grace' value is '0'.

Example :
---------
    # enter soft stop after 'killall -USR1 haproxy'
    # the service will still run 10 seconds after the signal
    listen http_proxy 0.0.0.0:80
        mode http
        grace 10000

    # this port is dedicated to a load-balancer, and must fail immediately
    listen health_check 0.0.0.0:60000
        mode health
        grace 0


As of version 1.2.8, a new soft-reconfiguration mechanism has been introduced.
It is now possible to "pause" all the proxies by sending a SIGTTOU signal to
the processes. This will disable the listening socket without breaking existing
connections. After that, sending a SIGTTIN signal to those processes enables
the listening sockets again. This is very useful to try to load a new
configuration or even a new version of haproxy without breaking existing
connections. If the load succeeds, then simply send a SIGUSR1 which will make
the previous proxies exit immediately once their sessions are closed ; and if
the load fails, then simply send a SIGTTIN to restore the service immediately.
Please note that the 'grace' parameter is ignored for SIGTTOU, as well as for
SIGUSR1 when the process was in the pause mode. Please also note that it would
be useful to save the pidfile before starting a new instance.

This mechanism fully exploited since 1.2.11 with the '-st' and '-sf' options
(see below).

2.4.1) Hot reconfiguration
--------------------------
The '-st' and '-sf' command line options are used to inform previously running
processes that a configuration is being reloaded. They will receive the SIGTTOU
signal to ask them to temporarily stop listening to the ports so that the new
process can grab them. If anything wrong happens, the new process will send
them a SIGTTIN to tell them to re-listen to the ports and continue their normal
work. Otherwise, it will either ask them to finish (-sf) their work then softly
exit, or immediately terminate (-st), breaking existing sessions. A typical use
of this allows a configuration reload without service interruption :

 # haproxy -p /var/run/haproxy.pid -sf $(cat /var/run/haproxy.pid)


2.5) Connections expiration time
--------------------------------
It is possible (and recommended) to configure several time-outs on TCP
connections. Three independant timers are adjustable with values specified
in milliseconds. A session will be terminated if either one of these timers
expire.

  - the time we accept to wait for data from the client, or for the client to
    accept data : 'clitimeout' :

        # client time-out set to 2mn30.
        clitimeout  150000

  - the time we accept to wait for data from the server, or for the server to
    accept data : 'srvtimeout' :

        # server time-out set to 30s.
        srvtimeout  30000

  - the time we accept to wait for a connection to establish on a server :
    'contimeout' :

        # we give up if the connection does not complete within 4 seconds
        contimeout  4000

Notes :
-------
  - 'contimeout' and 'srvtimeout' have no sense on 'health' mode servers ;
  - under high loads, or with a saturated or defective network, it's possible
    that some packets get lost. Since the first TCP retransmit only happens
    after 3 seconds, a time-out equal to, or lower than 3 seconds cannot
    compensate for a packet loss. A 4 seconds time-out seems a reasonable
    minimum which will considerably reduce connection failures.


2.6) Attempts to reconnect
--------------------------
After a connection failure to a server, it is possible to retry, potentially
on another server. This is useful if health-checks are too rare and you don't
want the clients to see the failures. The number of attempts to reconnect is
set by the 'retries' paramter.

Example :
---------
        # we can retry 3 times max after a failure
        retries 3

Please note that the reconnection attempt may lead to getting the connection
sent to a new server if the original one died between connection attempts.


2.7) Address of the dispatch server (deprecated)
------------------------------------------------
The server which will be sent all new connections is defined by the 'dispatch'
parameter, in the form <address>:<port>. It generally is dedicated to unknown
connections and will assign them a cookie, in case of HTTP persistence mode,
or simply is a single server in case of generic TCP proxy. This old mode is only
provided for backwards compatibility, but doesn't allow to check remote servers
state, and has a rather limited usage. All new setups should switch to 'balance'
mode. The principle of the dispatcher is to be able to perform the load
balancing itself, but work only on new clients so that the server doesn't need
to be a big machine.

Example :
---------
           # all new connections go there
        dispatch 192.168.1.2:80

Note :
------
This parameter has no sense for 'health' servers, and is incompatible with
'balance' mode.


2.8) Outgoing source address
----------------------------
It is often necessary to bind to a particular address when connecting to some
remote hosts. This is done via the 'source' parameter which is a per-proxy
parameter. A newer version may allow to fix different sources to reach different
servers. The syntax is 'source <address>[:<port>]', where <address> is a valid
local address (or '0.0.0.0' or '*' or empty to let the system choose), and
<port> is an optional parameter allowing the user to force the source port for
very specific needs. If the port is not specified or is '0', the system will
choose a free port. Note that as of version 1.1.18, the servers health checks
are also performed from the same source.

Examples :
----------
    listen http_proxy *:80
           # all connections take 192.168.1.200 as source address
        source 192.168.1.200:0

    listen rlogin_proxy *:513
           # use address 192.168.1.200 and the reserved port 900 (needs to be root)
        source 192.168.1.200:900


2.9) Setting the cookie name
----------------------------
In HTTP mode, it is possible to look for a particular cookie which will contain
a server identifier which should handle the connection. The cookie name is set
via the 'cookie' parameter.

Example :
---------
    listen http_proxy :80
        mode http
        cookie SERVERID

It is possible to change the cookie behaviour to get a smarter persistence,
depending on applications. It is notably possible to delete or modify a cookie
emitted by a server, insert a cookie identifying the server in an HTTP response
and even add a header to tell upstream caches not to cache this response.

Examples :
----------

To remove the cookie for direct accesses (ie when the server matches the one
which was specified in the client cookie) :

        cookie SERVERID indirect

To replace the cookie value with the one assigned to the server if any (no
cookie will be created if the server does not provide one, nor if the
configuration does not provide one). This lets the application put the cookie
exactly on certain pages (eg: successful authentication) :

        cookie SERVERID rewrite

To create a new cookie and assign the server identifier to it (in this case, all
servers should be associated with a valid cookie, since no cookie will simply
delete the cookie from the client's browser) :

        cookie SERVERID insert

To reuse an existing application cookie and prefix it with the server's
identifier, and remove it in the request, use the 'prefix' option. This allows
to insert a haproxy in front of an application without risking to break clients
which does not support more than one cookie :

        cookie JSESSIONID prefix

To insert a cookie and ensure that no upstream cache will store it, add the
'nocache' option :

        cookie SERVERID insert nocache

To insert a cookie only after a POST request, add 'postonly' after 'insert'.
This has the advantage that there's no risk of caching, and that all pages
seen before the POST one can still be cached :

        cookie SERVERID insert postonly

Notes :
-----------
- it is possible to combine 'insert' with 'indirect' or 'rewrite' to adapt to
  applications which already generate the cookie with an invalid content.

- in the case where 'insert' and 'indirect' are both specified, the cookie is
  never transmitted to the server, since it wouldn't understand it. This is the
  most application-transparent mode.

- it is particularly recommended to use 'nocache' in 'insert' mode if any
  upstream HTTP/1.0 cache is susceptible to cache the result, because this may
  lead to many clients going to the same server, or even worse, some clients
  having their server changed while retrieving a page from the cache.

- the 'prefix' mode normally does not need 'indirect', 'nocache', nor
  'postonly', because just as in the 'rewrite' mode, it relies on the
  application to know when a cookie can be emitted. However, since it has to
  fix the cookie name in every subsequent requests, you must ensure that the
  proxy will be used without any "HTTP keep-alive". Use option "httpclose" if
  unsure.

- when the application is well known and controlled, the best method is to
  only add the persistence cookie on a POST form because it's up to the
  application to select which page it wants the upstream servers to cache. In
  this case, you would use 'insert postonly indirect'.


2.10) Associating a cookie value with a server
----------------------------------------------
In HTTP mode, it's possible to associate a cookie value to each server. This
was initially used in combination with 'dispatch' mode to handle direct accesses
but it is now the standard way of doing the load balancing. The syntax is :

    server <identifier> <address>:<port> cookie <value>

- <identifier> is any name which can be used to identify the server in the logs.
- <address>:<port> specifies where the server is bound.
- <value> is the value to put in or to read from the cookie.

Example : the 'SERVERID' cookie can be either 'server01' or 'server02'
---------
    listen http_proxy :80
        mode http
        cookie SERVERID
        dispatch 192.168.1.100:80
        server web1 192.168.1.1:80 cookie server01
        server web2 192.168.1.2:80 cookie server02

Warning : the syntax has changed since version 1.0 !
---------


2.11) Application Cookies
-------------------------
Since 1.2.4 it is possible to catch the cookie that comes from an
application server in order to apply "application session stickyness".
The server's response is searched for 'appsession' cookie, the first
'len' bytes are used for matching and it is stored for a period of
'timeout'.
The syntax is:

    appsession <session_cookie> len <match_length> timeout <holdtime>

- <session_cookie> is the cookie, the server uses for it's session-handling
- <match_length> how many bytes/characters should be used for matching equal
                sessions 
- <holdtime> after this inactivaty time, in ms, the cookie will be deleted 
             from the sessionstore

The appsession is only per 'listen' section possible.

Example :
---------
    listen http_lb1 192.168.3.4:80
       mode    http
       capture request  header Cookie len 200
       # Havind a ServerID cookie on the client allows him to reach
       # the right server even after expiration of the appsession.
       cookie ServerID insert nocache indirect
       # Will memorize 52 bytes of the cookie 'JSESSIONID' and keep them
       # for 3 hours. It will match it in the cookie and the URL field.
       appsession JSESSIONID len 52 timeout 10800000
       server first1 10.3.9.2:10805 check inter 3000 cookie first
       server secon1 10.3.9.3:10805 check inter 3000 cookie secon
       server first1 10.3.9.4:10805 check inter 3000 cookie first
       server secon2 10.3.9.5:10805 check inter 3000 cookie secon
       option httpchk GET /test.jsp


3) Autonomous load balancer
===========================

The proxy can perform the load-balancing itself, both in TCP and in HTTP modes.
This is the most interesting mode which obsoletes the old 'dispatch' mode
described above. It has advantages such as server health monitoring, multiple
port binding and port mapping. To use this mode, the 'balance' keyword is used,
followed by the selected algorithm. Up to version 1.2.11, only 'roundrobin' was
available, which is also the default value if unspecified. Starting with
version 1.2.12, a new 'source' keyword appeared. In this mode, there will be no
dispatch address, but the proxy needs at least one server.

Example : same as the last one, with internal load balancer
---------

    listen http_proxy :80
        mode http
        cookie SERVERID
        balance roundrobin
        server web1 192.168.1.1:80 cookie server01
        server web2 192.168.1.2:80 cookie server02


Since version 1.1.22, it is possible to automatically determine on which port
the server will get the connection, depending on the port the client connected
to. Indeed, there now are 4 possible combinations for the server's <port> field:

  - unspecified or '0' :
    the connection will be sent to the same port as the one on which the proxy
    received the client connection itself.

  - numerical value (the only one supported in versions earlier than 1.1.22) :
    the connection will always be sent to the specified port.

  - '+' followed by a numerical value :
    the connection will be sent to the same port as the one on which the proxy
    received the connection, plus this value.

  - '-' followed by a numerical value :
    the connection will be sent to the same port as the one on which the proxy
    received the connection, minus this value.
    
Examples :
----------

# same as previous example

    listen http_proxy :80
        mode http
        cookie SERVERID
        balance roundrobin
        server web1 192.168.1.1 cookie server01
        server web2 192.168.1.2 cookie server02

# simultaneous relaying of ports 80, 81 and 8080-8089

    listen http_proxy :80,:81,:8080-8089
        mode http
        cookie SERVERID
        balance roundrobin
        server web1 192.168.1.1 cookie server01
        server web2 192.168.1.2 cookie server02

# relaying of TCP ports 25, 389 and 663 to ports 1025, 1389 and 1663

    listen http_proxy :25,:389,:663
        mode tcp
        balance roundrobin
        server srv1 192.168.1.1:+1000
        server srv2 192.168.1.2:+1000

As previously stated, version 1.2.12 brought the 'source' keyword. When this
keyword is used, the client's IP address is hashed and evenly distributed among
the available servers so that a same source IP will always go to the same
server as long as there are no change in the number of available servers. This
can be used for instance to bind HTTP and HTTPS to the same server. It can also
be used to improve stickyness when one part of the client population does not
accept cookies. In this case, only those ones will be perturbated should a
server fail.

NOTE: It is important to consider the fact that many clients surf the net
      through proxy farms which assign different IP addresses for each
      request. Others use dialup connections with a different IP at each
      connection. Thus, the 'source' parameter should be used with extreme
      care.

Examples :
----------

# make a same IP go to the same server whatever the service

    listen http_proxy
        bind :80,:443
        mode http
        balance source
        server web1 192.168.1.1
        server web2 192.168.1.2

# try to improve client-server binding by using both source IP and cookie :

    listen http_proxy :80
        mode http
        cookie SERVERID
        balance source
        server web1 192.168.1.1 cookie server01
        server web2 192.168.1.2 cookie server02


3.1) Server monitoring
----------------------
It is possible to check the servers status by trying to establish TCP
connections or even sending HTTP requests to them. A server which fails to
reply to health checks as expected will not be used by the load balancing
algorithms. To enable monitoring, add the 'check' keyword on a server line.
It is possible to specify the interval between tests (in milliseconds) with
the 'inter' parameter, the number of failures supported before declaring that
the server has fallen down with the 'fall' parameter, and the number of valid
checks needed for the server to fully get up with the 'rise' parameter. Since
version 1.1.22, it is also possible to send checks to a different port
(mandatory when none is specified) with the 'port' parameter. The default
values are the following ones :

  - inter : 2000
  - rise  : 2
  - fall  : 3
  - port  : default server port

The default mode consists in establishing TCP connections only. But in certain
types of application failures, it is often that the server continues to accept
connections because the system does it itself while the application is running
an endless loop, or is completely stuck. So in version 1.1.16 were introduced
HTTP health checks which only performed simple lightweight requests and analysed
the response. Now, as of version 1.1.23, it is possible to change the HTTP
method, the URI, and the HTTP version string (which even allows to send headers
with a dirty trick). To enable HTTP health-checks, use 'option httpchk'.

By default, requests use the 'OPTIONS' method because it's very light and easy
to filter from logs, and does it on '/'. Only HTTP responses 2xx and 3xx are
considered valid ones, and only if they come before the time to send a new
request is reached ('inter' parameter). If some servers block this type of
request, 3 other forms help to forge a request :

  - option httpchk               -> OPTIONS / HTTP/1.0
  - option httpchk URI           -> OPTIONS <URI> HTTP/1.0
  - option httpchk METH URI      -> <METH> <URI> HTTP/1.0
  - option httpchk METH URI VER  -> <METH> <URI> <VER>

See examples below.

Since version 1.1.17, it is possible to specify backup servers. These servers
are only sollicited when no other server is available. This may only be useful
to serve a maintenance page, or define one active and one backup server (seldom
used in TCP mode). To make a server a backup one, simply add the 'backup' option
on its line. These servers also support cookies, so if a cookie is specified for
a backup server, clients assigned to this server will stick to it even when the
other ones come back. Conversely, if no cookie is assigned to such a server,
the clients will get their cookies removed (empty cookie = removal), and will
be balanced against other servers once they come back. Please note that there
is no load-balancing among backup servers by default. If there are several
backup servers, the second one will only be used when the first one dies, and
so on. To force load-balancing between backup servers, specify the 'allbackups'
option.

Since version 1.1.17, it is also possible to visually check the status of all
servers at once. For this, you just have to send a SIGHUP signal to the proxy.
The servers status will be dumped into the logs at the 'notice' level, as well
as on <stderr> if not closed. For this reason, it's always a good idea to have
one local log server at the 'notice' level.

Since version 1.1.28 and 1.2.1, if an instance loses all its servers, an
emergency message will be sent in the logs to inform the administator that an
immediate action must be taken.

Since version 1.1.30 and 1.2.3, several servers can share the same cookie
value. This is particularly useful in backup mode, to select alternate paths
for a given server for example, to provide soft-stop, or to direct the clients
to a temporary page during an application restart. The principle is that when
a server is dead, the proxy will first look for another server which shares the
same cookie value for every client which presents the cookie. If there is no
standard server for this cookie, it will then look for a backup server which
shares the same name. Please consult the architecture guide for more information.

Examples :
----------
# same setup as in  paragraph 3) with TCP monitoring
    listen http_proxy 0.0.0.0:80
        mode http
        cookie SERVERID
        balance roundrobin
        server web1 192.168.1.1:80 cookie server01 check
        server web2 192.168.1.2:80 cookie server02 check inter 500 rise 1 fall 2

# same with HTTP monitoring via 'OPTIONS / HTTP/1.0'
    listen http_proxy 0.0.0.0:80
        mode http
        cookie SERVERID
        balance roundrobin
        option httpchk
        server web1 192.168.1.1:80 cookie server01 check
        server web2 192.168.1.2:80 cookie server02 check inter 500 rise 1 fall 2

# same with HTTP monitoring via 'OPTIONS /index.html HTTP/1.0'
    listen http_proxy 0.0.0.0:80
        mode http
        cookie SERVERID
        balance roundrobin
        option httpchk /index.html
        server web1 192.168.1.1:80 cookie server01 check
        server web2 192.168.1.2:80 cookie server02 check inter 500 rise 1 fall 2

# same with HTTP monitoring via 'HEAD /index.jsp? HTTP/1.1\r\nHost: www'
    listen http_proxy 0.0.0.0:80
        mode http
        cookie SERVERID
        balance roundrobin
        option httpchk HEAD /index.jsp? HTTP/1.1\r\nHost:\ www
        server web1 192.168.1.1:80 cookie server01 check
        server web2 192.168.1.2:80 cookie server02 check inter 500 rise 1 fall 2

# Load-balancing with 'prefixed cookie' persistence, and soft-stop using an
# alternate port 81 on the server for health-checks.
    listen http_proxy 0.0.0.0:80
        mode http
        cookie JSESSIONID prefix
        balance roundrobin
        option httpchk HEAD /index.jsp? HTTP/1.1\r\nHost:\ www
        server web1-norm 192.168.1.1:80 cookie s1 check port 81
        server web2-norm 192.168.1.2:80 cookie s2 check port 81
        server web1-stop 192.168.1.1:80 cookie s1 check port 80 backup
        server web2-stop 192.168.1.2:80 cookie s2 check port 80 backup

# automatic insertion of a cookie in the server's response, and automatic
# deletion of the cookie in the client request, while asking upstream caches
# not to cache replies.
    listen web_appl 0.0.0.0:80
        mode http
        cookie SERVERID insert nocache indirect
        balance roundrobin
        server web1 192.168.1.1:80 cookie server01 check
        server web2 192.168.1.2:80 cookie server02 check

# same with off-site application backup and local error pages server
    listen web_appl 0.0.0.0:80
        mode http
        cookie SERVERID insert nocache indirect
        balance roundrobin
        server web1 192.168.1.1:80 cookie server01 check
        server web2 192.168.1.2:80 cookie server02 check
        server web-backup 192.168.2.1:80 cookie server03 check backup
        server web-excuse 192.168.3.1:80 check backup

# SMTP+TLS relaying with health-checks and backup servers

    listen http_proxy :25,:587
        mode tcp
        balance roundrobin
        server srv1 192.168.1.1 check port 25 inter 30000 rise 1 fall 2
        server srv2 192.168.1.2 backup

# Load-balancing using a backup pool (requires haproxy 1.2.9)
    listen http_proxy 0.0.0.0:80
        mode http
        balance roundrobin
        option httpchk
        server inst1 192.168.1.1:80 cookie s1 check
        server inst2 192.168.1.2:80 cookie s2 check
        server inst3 192.168.1.3:80 cookie s3 check
        server back1 192.168.1.10:80 check backup
        server back2 192.168.1.11:80 check backup
        option allbackups  # all backups will be used


3.2) Redistribute connections in case of failure
------------------------------------------------
In HTTP mode, if a server designated by a cookie does not respond, the clients
may definitely stick to it because they cannot flush the cookie, so they will
not be able to access the service anymore. Specifying 'redispatch' will allow
the proxy to break their persistence and redistribute them to working servers.

Example :
---------
    listen http_proxy 0.0.0.0:80
        mode http
        cookie SERVERID
        dispatch 192.168.1.100:80
        server web1 192.168.1.1:80 cookie server01
        server web2 192.168.1.2:80 cookie server02
        redispatch # send back to dispatch in case of connection failure

Up to, and including version 1.1.16, this parameter only applied to connection
failures. Since version 1.1.17, it also applies to servers which have been
detected as failed by the health check mechanism. Indeed, a server may be broken
but still accepting connections, which would not solve every case. But it is
possible to conserve the old behaviour, that is, make a client insist on trying
to connect to a server even if it is said to be down, by setting the 'persist'
option :

    listen http_proxy 0.0.0.0:80
        mode http
        option persist
        cookie SERVERID
        dispatch 192.168.1.100:80
        server web1 192.168.1.1:80 cookie server01
        server web2 192.168.1.2:80 cookie server02
        redispatch # send back to dispatch in case of connection failure


3.3) Assigning different weights to servers
-------------------------------------------
Sometimes you will need to bring new servers to increase your server farm's
capacity, but the new server will be either smaller (emergency use of anything
that fits) or bigger (when investing in new hardware). For this reason, it
might be wise to be able to send more clients to biggest servers. Till version
1.2.11, it was necessary to replicate the same server multiple times in the
configuration. Starting with 1.2.12, the 'weight' option is available. HAProxy
then computes the most homogenous possible map of servers based on their
weights so that the load gets distributed as smoothly as possible among them.
The weight, between 1 and 256, should reflect one server's capacity relative to
others. Weight 1 represents the lowest frequency and 256 the highest. This way,
if a server fails, the remaining capacities are still respected.

Example :
---------
# fair distribution among two opterons and one old pentium3

    listen web_appl 0.0.0.0:80
        mode http
        cookie SERVERID insert nocache indirect
        balance roundrobin
        server pentium3-800 192.168.1.1:80 cookie server01 weight  8 check
        server opteron-2.0G 192.168.1.2:80 cookie server02 weight 20 check
        server opteron-2.4G 192.168.1.3:80 cookie server03 weight 24 check
        server web-backup1 192.168.2.1:80 cookie server04 check backup
        server web-excuse 192.168.3.1:80 check backup

Notes :
-------
  - if unspecified, the default weight is 1

  - the weight does not impact health checks, so it is cleaner to use weights
    than replicating the same server several times

  - weights also work on backup servers if the 'allbackups' option is used

  - the weights also apply to the source address load balancing
    ('balance source').

  - whatever the weights, the first server will always be assigned first. This
    is helpful for troubleshooting.

  - for the purists, the map calculation algorithm gives precedence to first
    server, so the map is the most uniform when servers are declared in
    ascending order relative to their weights.

The load distribution will follow exactly this sequence :

        Request|                   1 1 1 1
        number | 1 2 3 4 5 6 7 8 9 0 1 2 3
       --------+---------------------------
        p3-800 | X . . . . . . X . . . . .
        opt-20 | . X . X . X . . . X . X .
        opt-24 | . . X . X . X . X . X . X


3.4) Limiting the number of concurrent sessions on each server
--------------------------------------------------------------
Some pre-forked servers such as Apache suffer from too many concurrent
sessions, because it's very expensive to run hundreds or thousands of
processes on one system. One solution is to increase the number of servers
and load-balance between them, but it is a problem when the only goal is
to resist to short surges.

To solve this problem, a new feature was implemented in HAProxy 1.2.13.
It's a per-server 'maxconn', associated with a per-server and a per-proxy
queue. This transforms haproxy into a request buffer between the thousands of
clients and the few servers. On many circumstances, lowering the maxconn value
will increase the server's performance and decrease the overall response times
because the servers will be less congested.

When a request tries to reach any server, the first non-saturated server is
used, respective to the load balancing algorithm. If all servers are saturated,
then the request gets queued into the instance's global queue. It will be
dequeued once a server will have freed a session and all previously queued
requests have been processed.

If a request references a particular server (eg: source hashing, or persistence
cookie), and if this server is full, then the request will be queued into the
server's dedicated queue. This queue has higher priority than the global queue,
so it's easier for already registered users to enter the site than for new
users.

For this, the logs have been enhanced to show the number of sessions per
server, the request's position in the queue and the time spent in the queue.
This helps doing capacity planning. See the 'logs' section below for more info.

Example :
---------
    # be nice with P3 which only has 256 MB of RAM.
    listen web_appl 0.0.0.0:80
        maxconn 10000
        mode http
        cookie SERVERID insert nocache indirect
        balance roundrobin
        server pentium3-800 192.168.1.1:80 cookie s1 weight  8 maxconn 100 check
        server opteron-2.0G 192.168.1.2:80 cookie s2 weight 20 maxconn 300 check
        server opteron-2.4G 192.168.1.3:80 cookie s3 weight 24 maxconn 300 check
        server web-backup1 192.168.2.1:80 cookie s4 check maxconn 200 backup
        server web-excuse 192.168.3.1:80 check backup

Notes :
-------
  - The requests will not stay indefinitely in the queue, they follow the
    'contimeout' parameter, and if a request cannot be dequeued within this
    timeout because the server is saturated or because the queue is filled,
    the session will expire with a 503 error.

  - setting too low values for maxconn might improve performance but might also
    allow slow users to block access to the server for other users.


4) Additionnal features
=======================

Other features are available. They are transparent mode, event logging, header
rewriting/filtering, and the status as an HTML page.


4.1) Network features
---------------------
4.1.1) Transparent mode
-----------------------
In HTTP mode, the 'transparent' keyword allows to intercept sessions which are
routed through the system hosting the proxy. This mode was implemented as a
replacement for the 'dispatch' mode, since connections without cookie will be
sent to the original address while known cookies will be sent to the servers.
This mode implies that the system can redirect sessions to a local port.

Example :
---------
    listen http_proxy 0.0.0.0:65000
        mode http
        transparent
        cookie SERVERID
        server server01 192.168.1.1:80
        server server02 192.168.1.2:80

    # iptables -t nat -A PREROUTING -i eth0 -p tcp -d 192.168.1.100 \
      --dport 80 -j REDIRECT --to-ports 65000

Note :
------
If the port is left unspecified on the server, the port the client connected to
will be used. This allows to relay a full port range without using transparent
mode nor thousands of file descriptors, provided that the system can redirect
sessions to local ports.

Example :
---------
    # redirect all ports to local port 65000, then forward to the server on the
    # original port.
    listen http_proxy 0.0.0.0:65000
        mode tcp
        server server01 192.168.1.1 check port 60000
        server server02 192.168.1.2 check port 60000

    # iptables -t nat -A PREROUTING -i eth0 -p tcp -d 192.168.1.100 \
      -j REDIRECT --to-ports 65000

4.1.2) Per-server source address binding
----------------------------------------
As of versions 1.1.30 and 1.2.3, it is possible to specify a particular source
to reach each server. This is useful when reaching backup servers from a
different LAN, or to use an alternate path to reach the same server. It is also
usable to provide source load-balancing for outgoing connections. Obviously,
the same source address is used to send health-checks.

Example :
---------
    # use a particular source to reach both servers
    listen http_proxy 0.0.0.0:65000
        mode http
        balance roundrobin
        server server01 192.168.1.1:80 source 192.168.2.13
        server server02 192.168.1.2:80 source 192.168.2.13

Example :
---------
    # use a particular source to reach each servers
    listen http_proxy 0.0.0.0:65000
        mode http
        balance roundrobin
        server server01 192.168.1.1:80 source 192.168.1.1
        server server02 192.168.2.1:80 source 192.168.2.1

Example :
---------
    # provide source load-balancing to reach the same proxy through 2 WAN links
    listen http_proxy 0.0.0.0:65000
        mode http
        balance roundrobin
        server remote-proxy-way1 192.168.1.1:3128 source 192.168.2.1
        server remote-proxy-way2 192.168.1.1:3128 source 192.168.3.1

Example :
---------
    # force a TCP connection to bind to a specific port
    listen http_proxy 0.0.0.0:2000
        mode tcp
        balance roundrobin
        server srv1 192.168.1.1:80 source 192.168.2.1:20
        server srv2 192.168.1.2:80 source 192.168.2.1:20

4.1.3) TCP keep-alive
---------------------
With version 1.2.7, it becomes possible to enable TCP keep-alives on both the
client and server sides. This makes it possible to prevent long sessions from
expiring on external layer 4 components such as firewalls and load-balancers.
It also allows the system to terminate dead sessions when no timeout has been
set (not recommanded). The proxy cannot set the keep-alive probes intervals nor
maximal count, consult your operating system manual for this. There are 3
options to enable TCP keep-alive :

	option tcpka	# enables keep-alive both on client and server side
	option clitcpka	# enables keep-alive only on client side
	option srvtcpka	# enables keep-alive only on server side


4.2) Event logging
------------------

HAProxy's strength certainly lies in its precise logs. It probably provides the
finest level of information available for such a product, which is very
important for troubleshooting complex environments. Standard log information
include client ports, TCP/HTTP state timers, precise session state at
termination and precise termination cause, information about decisions to
direct trafic to a server, and of course the ability to capture arbitrary
headers.

In order to improve administrators reactivity, it offers a great transparency
about encountered problems, both internal and external, and it is possible to
send logs to different sources at the same time with different level filters :

  - global process-level logs (system errors, start/stop, etc..)
  - per-listener system and internal errors (lack of resource, bugs, ...)
  - per-listener external troubles (servers up/down, max connections)
  - per-listener activity (client connections), either at the establishment or
    at the termination.

The ability to distribute different levels of logs to different log servers
allow several production teams to interact and to fix their problems as soon
as possible. For example, the system team might monitor system-wide errors,
while the application team might be monitoring the up/down for their servers in
real time, and the security team might analyze the activity logs with one hour
delay.

4.2.1) Log levels
-----------------
TCP and HTTP connections can be logged with informations such as date, time,
source IP address, destination address, connection duration, response times,
HTTP request, the HTTP return code, number of bytes transmitted, the conditions
in which the session ended, and even exchanged cookies values, to track a
particular user's problems for example. All messages are sent to up to two
syslog servers. Consult section 1.1 for more info about log facilities. The
syntax follows :

    log <address_1> <facility_1> [max_level_1]
    log <address_2> <facility_2> [max_level_2]
or
    log global

Note :
------
The particular syntax 'log global' means that the same log configuration as the
'global' section will be used.

Example :
---------
    listen http_proxy 0.0.0.0:80
        mode http
        log 192.168.2.200 local3
        log 192.168.2.201 local4

4.2.2) Log format
-----------------
By default, connections are logged at the TCP level, as soon as the session
establishes between the client and the proxy. By enabling the 'tcplog' option,
the proxy will wait until the session ends to generate an enhanced log
containing more information such as session duration and its state during the
disconnection. The number of remaining session after disconnection is also
indicated (for the server, the listener, and the process).

Example of TCP logging :
------------------------
    listen relais-tcp 0.0.0.0:8000
        mode tcp
        option tcplog
        log 192.168.2.200 local3

>>> haproxy[18989]: 127.0.0.1:34550 [15/Oct/2003:15:24:28] relais-tcp Srv1 0/0/5007 0 -- 1/1/1 0/0
  
    Field  Format                                        Example

        1  process_name '[' pid ']:'                     haproxy[18989]:
        2  client_ip ':' client_port                     127.0.0.1:34550
        3  '[' date ']'                                  [15/Oct/2003:15:24:28]
        4  listener_name                                 relais-tcp
        5  server_name                                   Srv1
        6  queue_time '/' connect_time '/' total_time    0/0/5007
        7  bytes_read                                    0
        8  termination_state                             --
        9  srv_conn '/' listener_conn '/' process_conn   1/1/1
       10  position in srv_queue / listener_queue        0/0


Another option, 'httplog', provides more detailed information about HTTP
contents, such as the request and some cookies. In the event where an external
component would establish frequent connections to check the service, logs may be
full of useless lines. So it is possible not to log any session which didn't
transfer any data, by the setting of the 'dontlognull' option. This only has
effect on sessions which are established then closed.

Example of HTTP logging :
-------------------------
    listen http_proxy 0.0.0.0:80
        mode http
        option httplog
        option dontlognull
        log 192.168.2.200 local3

>>> haproxy[674]: 127.0.0.1:33319 [15/Oct/2003:08:31:57] relais-http Srv1 9/0/7/147/723 200 243 - - ---- 2/3/3 0/0 "HEAD / HTTP/1.0"

More complete example
    haproxy[18989]: 10.0.0.1:34552 [15/Oct/2003:15:26:31] relais-http Srv1 3183/-1/-1/-1/11215 503 0 - - SC-- 137/202/205 0/0 {w.ods.org|Mozilla} {} "HEAD / HTTP/1.0" 

    Field  Format                                        Example
  
        1  process_name  '[' pid ']:'                    haproxy[18989]:
        2  client_ip ':' client_port                     10.0.0.1:34552
        3  '[' date ']'                                  [15/Oct/2003:15:26:31]
        4  listener_name                                 relais-http
        5  server_name                                   Srv1
        6  Tq '/' Tw '/' Tc '/' Tr '/' Tt                3183/-1/-1/-1/11215
        7  HTTP_return_code                              503
        8  bytes_read                                    0
        9  captured_request_cookie                       -
       10  captured_response_cookie                      -
       11  termination_state                             SC--
       12  srv_conn '/' listener_conn '/' process_conn   137/202/205
       13  position in srv_queue / listener_queue        0/0
       14  '{' captured_request_headers '}'              {w.ods.org|Mozilla}
       15  '{' captured_response_headers '}'             {}
       16  '"' HTTP_request '"'                          "HEAD / HTTP/1.0"
  
Note for log parsers: the URI is ALWAYS the end of the line starting with the
                      first double quote '"'.

The problem when logging at end of connection is that you have no clue about
what is happening during very long sessions. To workaround this problem, a
new option 'logasap' has been introduced in 1.1.28/1.2.1. When specified, the
proxy will log as soon as possible, just before data transfer begins. This means
that in case of TCP, it will still log the connection status to the server, and
in case of HTTP, it will log just after processing the server headers. In this
case, the number of bytes reported is the number of header bytes sent to the
client.

In order to avoid confusion with normal logs, the total time field and the
number of bytes are prefixed with a '+' sign which mean that real numbers are
certainly bigger.

Example :
---------

    listen http_proxy 0.0.0.0:80
        mode http
        option httplog
        option dontlognull
        option logasap
        log 192.168.2.200 local3

>>> haproxy[674]: 127.0.0.1:33320 [15/Oct/2003:08:32:17] relais-http Srv1 9/10/7/14/+30 200 +243 - - ---- 1/1/3 1/0 "GET /image.iso HTTP/1.0"

4.2.3) Timing events
--------------------
Timers provide a great help in trouble shooting network problems. All values
are reported in milliseconds (ms). In HTTP mode, four control points are
reported under the form 'Tq/Tw/Tc/Tr/Tt' :

  - Tq: total time to get the client request.
    It's the time elapsed between the moment the client connection was accepted
    and the moment the proxy received the last HTTP header. The value '-1'
    indicates that the end of headers (empty line) has never been seen.

  - Tw: total time spent in the queues waiting for a connection slot. It
    accounts for listener's queue as well as the server's queue, and depends
    on the queue size, and the time needed for the server to complete previous
    sessions. The value '-1' means that the request was killed before reaching
    the queue.

  - Tc: total time to establish the TCP connection to the server.
    It's the time elapsed between the moment the proxy sent the connection
    request, and the moment it was acknowledged, or between the TCP SYN packet
    and the matching SYN/ACK in return. The value '-1' means that the
    connection never established.

  - Tr: server response time. It's the time elapsed between the moment the
    TCP connection was established to the server and the moment it send its
    complete response header. It purely shows its request processing time,
    without the network overhead due to the data transmission. The value '-1'
    means that the last the response header (empty line) was never seen.

  - Tt: total session duration time, between the moment the proxy accepted it
    and the moment both ends were closed. The exception is when the 'logasap'
    option is specified. In this case, it only equals (Tq+Tw+Tc+Tr), and is
    prefixed with a '+' sign. From this field, we can deduce Td, the data
    transmission time, by substracting other timers when valid :

        Td = Tt - (Tq + Tw + Tc + Tr)

    Timers with '-1' values have to be excluded from this equation.

In TCP mode ('option tcplog'), only Tw, Tc and Tt are reported.

These timers provide precious indications on trouble causes. Since the TCP
protocol defines retransmit delays of 3, 6, 12... seconds, we know for sure
that timers close to multiples of 3s are nearly always related to packets lost
due to network problems (wires or negociation). Moreover, if <Tt> is close to
a timeout value specified in the configuration, it often means that a session
has been aborted on time-out.

Most common cases :

  - If Tq is close to 3000, a packet has probably been lost between the client
    and the proxy.
  - If Tc is close to 3000, a packet has probably been lost between the server
    and the proxy during the server connection phase. This one should always be
    very low (less than a few tens).
  - If Tr is nearly always lower than 3000 except some rare values which seem to
    be the average majored by 3000, there are probably some packets lost between
    the proxy and the server.
  - If Tt is often slightly higher than a time-out, it's often because the
    client and the server use HTTP keep-alive and the session is maintained
    after the response ends. Se further for how to disable HTTP keep-alive.

Other cases ('xx' means any value to be ignored) :
  -1/xx/xx/xx/Tt: the client was not able to send its complete request in time,
                  or that it aborted it too early.
  Tq/-1/xx/xx/Tt: it was not possible to process the request, maybe because
                  servers were out of order.
  Tq/Tw/-1/xx/Tt: the connection could not establish on the server. Either it
                  refused it or it timed out after Tt-(Tq+Tw) ms.
  Tq/Tw/Tc/-1/Tt: the server has accepted the connection but did not return a
                  complete response in time, or it closed its connexion
                  unexpectedly, after Tt-(Tq+Tw+Tc) ms.

4.2.4) Session state at disconnection
-------------------------------------
TCP and HTTP logs provide a session completion indicator in the
<termination_state> field, just before the number of active
connections. It is 2-characters long in TCP, and 4-characters long in
HTTP, each of which has a special meaning :

  - On the first character, a code reporting the first event which caused the
    session to terminate :

        C : the TCP session was unexpectedly aborted by the client.

        S : the TCP session was unexpectedly aborted by the server, or the
            server explicitly refused it.

        P : the session was prematurely aborted by the proxy, because of a
            connection limit enforcement, because a DENY filter was matched,
            or because of a security check which detected and blocked a
            dangerous error in server response which might have caused
            information leak (eg: cacheable cookie).

        R : a resource on the proxy has been exhausted (memory, sockets, source
            ports, ...). Usually, this appears during the connection phase, and
            system logs should contain a copy of the precise error.

        I : an internal error was identified by the proxy during a self-check.
            This should NEVER happen, and you are encouraged to report any log
            containing this, because this is a bug.

        c : the client-side time-out expired first.

        s : the server-side time-out expired first.

        - : normal session completion.

  - on the second character, the TCP/HTTP session state when it was closed :

        R : waiting for complete REQUEST from the client (HTTP only). Nothing
            was sent to any server.

        Q : waiting in the QUEUE for a connection slot. This can only happen on
            servers which have a 'maxconn' parameter set. No connection attempt
            was made to any server.

        C : waiting for CONNECTION to establish on the server. The server might
            at most have noticed a connection attempt.

        H : waiting for, receiving and processing server HEADERS (HTTP only).

        D : the session was in the DATA phase.

        L : the proxy was still transmitting LAST data to the client while the
            server had already finished.

        - : normal session completion after end of data transfer.

  - the third character tells whether the persistence cookie was provided by
    the client (only in HTTP mode) :

        N : the client provided NO cookie. This is usually the case on new
            connections.

        I : the client provided an INVALID cookie matching no known
            server. This might be caused by a recent configuration change,
            mixed cookies between HTTP/HTTPS sites, or an attack.

        D : the client provided a cookie designating a server which was DOWN,
            so either the 'persist' option was used and the client was sent to
            this server, or it was not set and the client was redispatched to
            another server.

        V : the client provided a valid cookie, and was sent to the associated
            server.

        - : does not apply (no cookie set in configuration).

  - the last character reports what operations were performed on the persistence
    cookie returned by the server (only in HTTP mode) :

        N : NO cookie was provided by the server, and none was inserted either.

        I : no cookie was provided by the server, and the proxy INSERTED one.

        P : a cookie was PROVIDED by the server and transmitted as-is.

        R : the cookie provided by the server was REWRITTEN by the proxy.

        D : the cookie provided by the server was DELETED by the proxy.

        - : does not apply (no cookie set in configuration).

The combination of the two first flags give a lot of information about what was
happening when the session terminated. It can be helpful to detect server
saturation, network troubles, local system resource starvation, attacks, etc...

The most common termination flags combinations are indicated here.

   Flags  Reason
      CR  The client aborted before sending a full request. Most probably the
          request was done by hand using a telnet client, and aborted early.

      cR  The client timed out before sending a full request. This is sometimes
          caused by too large TCP MSS values on the client side for PPPoE
          networks which cannot transport full-sized packets, or by clients
          sending requests by hand and not typing fast enough.

      SC  The server explicitly refused the connection (the proxy received a
          TCP RST or an ICMP in return). Under some circumstances, it can
          also be the network stack telling the proxy that the server is
          unreachable (eg: no route, or no ARP response on local network).

      sC  The connection to the server did not complete during contimeout.

      PC  The proxy refused to establish a connection to the server because the
          maxconn limit has been reached. The listener's maxconn parameter may
          be increased in the proxy configuration, as well as the global
          maxconn parameter.

      RC  A local resource has been exhausted (memory, sockets, source ports)
          preventing the connection to the server from establishing. The error
          logs will tell precisely what was missing. Anyway, this can only be
          solved by system tuning.

      cH  The client timed out during a POST request. This is sometimes caused
          by too large TCP MSS values for PPPoE networks which cannot transport
          full-sized packets.

      CH  The client aborted while waiting for the server to start responding.
          It might be the server taking too long to respond or the client
          clicking the 'Stop' button too fast.

      CQ  The client aborted while its session was queued, waiting for a server
          with enough empty slots to accept it. It might be that either all the
          servers were saturated or the assigned server taking too long to
          respond.

      sQ  The session spent too much time in queue and has been expired.

      SH  The server aborted before sending its full headers, or it crashed.

      sH  The server failed to reply during the srvtimeout delay, which
          indicates too long transactions, probably caused by back-end
          saturation. The only solutions are to fix the problem on the
          application or to increase the 'srvtimeout' parameter to support
          longer delays (at the risk of the client giving up anyway).
      
      PR  The proxy blocked the client's request, either because of an invalid
          HTTP syntax, in which case it returned an HTTP 400 error to the
          client, or because a deny filter matched, in which case it returned
          an HTTP 403 error.

      PH  The proxy blocked the server's response, because it was invalid,
          incomplete, dangerous (cache control), or matched a security filter.
          In any case, an HTTP 502 error is sent to the client.

      cD  The client did not read any data for as long as the clitimeout delay.
          This is often caused by network failures on the client side.

      CD  The client unexpectedly aborted during data transfer. This is either
          caused by a browser crash, or by a keep-alive session between the
          server and the client terminated first by the client.

      sD  The server did nothing during the srvtimeout delay. This is often
          caused by too short timeouts on L4 equipements before the server
          (firewalls, load-balancers, ...).

4.2.5) Non-printable characters
-------------------------------
As of version 1.1.29, non-printable characters are not sent as-is into log
files, but are converted to their two-digits hexadecimal representation,
prefixed by the character '#'. The only characters that can now be logged
without being escaped are between 32 and 126 (inclusive). Obviously, the
escape character '#' is also encoded to avoid any ambiguity. It is the same for
the character '"', as well as '{', '|' and '}' when logging headers.

4.2.6) Capturing HTTP headers and cookies
-----------------------------------------
Version 1.1.23 brought cookie capture, and 1.1.29 the header capture. All this
is performed using the 'capture' keyword.

Cookie capture makes it easy to track a complete user session. The syntax is :

    capture cookie <cookie_prefix> len <capture_length>

This will enable cookie capture from both requests and responses. This way,
it's easy to detect when a user switches to a new session for example, because
the server will reassign it a new cookie.

The FIRST cookie whose name starts with <cookie_prefix> will be captured, and
logged as 'NAME=value', without exceeding <capture_length> characters (64 max).
When the cookie name is fixed and known, it's preferable to suffix '=' to it to
ensure that no other cookie will be logged.

Examples :
----------
    # capture the first cookie whose name starts with "ASPSESSION"
    capture cookie ASPSESSION len 32

    # capture the first cookie whose name is exactly "vgnvisitor"
    capture cookie vgnvisitor= len 32

In the logs, the field preceeding the completion indicator contains the cookie
value as sent by the server, preceeded by the cookie value as sent by the
client. Each of these field is replaced with '-' when no cookie was seen or
when the option is disabled.

Header captures have a different goal. They are useful to track unique request
identifiers set by a previous proxy, virtual host names, user-agents, POST
content-length, referrers, etc. In the response, one can search for information
about the response length, how the server asked the cache to behave, or an
object location during a redirection. As for cookie captures, it is both
possible to include request headers and response headers at the same time. The
syntax is :

    capture request  header <name> len <max length>
    capture response header <name> len <max length>

Note: Header names are not case-sensitive.

Examples:
---------
    # keep the name of the virtual server
    capture request  header Host len 20
    # keep the amount of data uploaded during a POST
    capture request  header Content-Length len 10

    # note the expected cache behaviour on the response
    capture response header Cache-Control len 8
    # note the URL location during a redirection
    capture response header Location len 20

Non-existant headers are logged as empty strings, and if one header appears more
than once, only its last occurence will be kept. Request headers are grouped
within braces '{' and '}' in the same order as they were declared, and delimited
with a vertical bar '|' without any space. Response headers follow the same
representation, but are displayed after a space following the request headers
block. These blocks are displayed just before the HTTP request in the logs.

Example :

  Config:

    capture request  header Host len 20
    capture request  header Content-Length len 10
    capture request  header Referer len 20
    capture response header Server len 20
    capture response header Content-Length len 10
    capture response header Cache-Control len 8
    capture response header Via len 20
    capture response header Location len 20

  Log :

    Aug  9 20:26:09 localhost haproxy[2022]: 127.0.0.1:34014 [09/Aug/2004:20:26:09] relais-http netcache 0/0/0/162/+162 200 +350 - - ---- 0/0/0 0/0 {fr.adserver.yahoo.co||http://fr.f416.mail.} {|864|private||} "GET http://fr.adserver.yahoo.com/"
    Aug  9 20:30:46 localhost haproxy[2022]: 127.0.0.1:34020 [09/Aug/2004:20:30:46] relais-http netcache 0/0/0/182/+182 200 +279 - - ---- 0/0/0 0/0 {w.ods.org||} {Formilux/0.1.8|3495|||} "GET http://w.ods.org/sytadin.html HTTP/1.1" 
    Aug  9 20:30:46 localhost haproxy[2022]: 127.0.0.1:34028 [09/Aug/2004:20:30:46] relais-http netcache 0/0/2/126/+128 200 +223 - - ---- 0/0/0 0/0 {www.infotrafic.com||http://w.ods.org/syt} {Apache/2.0.40 (Red H|9068|||} "GET http://www.infotrafic.com/images/live/cartesidf/grandes/idf_ne.png HTTP/1.1" 


4.2.7) Examples of logs
-----------------------
- haproxy[674]: 127.0.0.1:33319 [15/Oct/2003:08:31:57] relais-http Srv1 6559/0/7/147/6723 200 243 - - ---- 1/3/5 0/0 "HEAD / HTTP/1.0"
  => long request (6.5s) entered by hand through 'telnet'. The server replied
     in 147 ms, and the session ended normally ('----')

- haproxy[674]: 127.0.0.1:33319 [15/Oct/2003:08:31:57] relais-http Srv1 6559/1230/7/147/6870 200 243 - - ---- 99/239/324 0/9 "HEAD / HTTP/1.0"
  => Idem, but the request was queued in the global queue behind 9 other
     requests, and waited there for 1230 ms.

- haproxy[674]: 127.0.0.1:33320 [15/Oct/2003:08:32:17] relais-http Srv1 9/0/7/14/+30 200 +243 - - ---- 1/3/3 0/0 "GET /image.iso HTTP/1.0"
  => request for a long data transfer. The 'logasap' option was specified, so
     the log was produced just before transfering data. The server replied in
     14 ms, 243 bytes of headers were sent to the client, and total time from
     accept to first data byte is 30 ms.

- haproxy[674]: 127.0.0.1:33320 [15/Oct/2003:08:32:17] relais-http Srv1 9/0/7/14/30 502 243 - - PH-- 0/2/3 0/0 "GET /cgi-bin/bug.cgi? HTTP/1.0"
  => the proxy blocked a server response either because of an 'rspdeny' or
     'rspideny' filter, or because it blocked sensible information which risked
     being cached. In this case, the response is replaced with a '502 bad
     gateway'.

- haproxy[18113]: 127.0.0.1:34548 [15/Oct/2003:15:18:55] relais-http <NOSRV> -1/-1/-1/-1/8490 -1 0 - - CR-- 0/2/2 0/0 "" 
  => the client never completed its request and aborted itself ('C---') after
     8.5s, while the proxy was waiting for the request headers ('-R--').
     Nothing was sent to the server.

- haproxy[18113]: 127.0.0.1:34549 [15/Oct/2003:15:19:06] relais-http <NOSRV> -1/-1/-1/-1/50001 408 0 - - cR-- 2/2 0/0 "" 
  => The client never completed its request, which was aborted by the time-out
     ('c---') after 50s, while the proxy was waiting for the request headers ('-R--').
     Nothing was sent to the server, but the proxy could send a 408 return code
     to the client.

- haproxy[18989]: 127.0.0.1:34550 [15/Oct/2003:15:24:28] relais-tcp Srv1 0/0/5007 0 cD 0/0/0 0/0
  => This is a 'tcplog' entry. Client-side time-out ('c----') occured after 5s.

- haproxy[18989]: 10.0.0.1:34552 [15/Oct/2003:15:26:31] relais-http Srv1 3183/-1/-1/-1/11215 503 0 - - SC-- 115/202/205 0/0 "HEAD / HTTP/1.0" 
  => The request took 3s to complete (probably a network problem), and the
     connection to the server failed ('SC--') after 4 attemps of 2 seconds
     (config says 'retries 3'), then a 503 error code was sent to the client.
     There were 115 connections on this server, 202 connections on this proxy,
     and 205 on the global process. It is possible that the server refused the
     connection because of too many already established.


4.3) HTTP header manipulation
-----------------------------
In HTTP mode, it is possible to rewrite, add or delete some of the request and
response headers based on regular expressions. It is also possible to block a
request or a response if a particular header matches a regular expression,
which is enough to stops most elementary protocol attacks, and to protect
against information leak from the internal network. But there is a limitation
to this : since haproxy's HTTP engine knows nothing about keep-alive, only
headers passed during the first request of a TCP session will be seen. All
subsequent headers will be considered data only and not analyzed. Furthermore,
haproxy doesn't touch data contents, it stops at the end of headers.

The syntax is :
   reqadd    <string>             to add a header to the request
   reqrep    <search> <replace>   to modify the request
   reqirep   <search> <replace>   same, but ignoring the case
   reqdel    <search>             to delete a header in the request
   reqidel   <search>             same, but ignoring the case
   reqallow  <search>             definitely allow a request if a header matches <search>
   reqiallow <search>             same, but ignoring the case
   reqdeny   <search>             denies a request if a header matches <search>
   reqideny  <search>             same, but ignoring the case
   reqpass   <search>             ignore a header matching <search>
   reqipass  <search>             same, but ignoring the case

   rspadd   <string>              to add a header to the response
   rsprep   <search> <replace>    to modify the response
   rspirep  <search> <replace>    same, but ignoring the case
   rspdel   <search>              to delete the response
   rspidel  <search>              same, but ignoring the case
   rspdeny  <search>              replaces a response with a HTTP 502 if a header matches <search>
   rspideny <search>              same, but ignoring the case


<search> is a POSIX regular expression (regex) which supports grouping through
parenthesis (without the backslash). Spaces and other delimiters must be
prefixed with a backslash ('\') to avoid confusion with a field delimiter.
Other characters may be prefixed with a backslash to change their meaning :

  \t   for a tab
  \r   for a carriage return (CR)
  \n   for a new line (LF)
  \    to mark a space and differentiate it from a delimiter
  \#   to mark a sharp and differentiate it from a comment
  \\   to use a backslash in a regex
  \\\\ to use a backslash in the text (*2 for regex, *2 for haproxy)
  \xXX to write the ASCII hex code XX as in the C language


<replace> containst the string to be used to replace the largest portion of text
matching the regex. It can make use of the special characters above, and can
reference a substring delimited by parenthesis in the regex, by the group
numerical order from 1 to 9. In this case, you would write a backslah ('\')
immediately followed by one digit indicating the group position.

<string> represents the string which will systematically be added after the last
header line. It can also use special characters above.

Notes :
-------
  - the first line is considered as a header, which makes it possible to rewrite
    or filter HTTP requests URIs or response codes.
  - 'reqrep' is the equivalent of 'cliexp' in version 1.0, and 'rsprep' is the
    equivalent of 'srvexp' in 1.0. Those names are still supported but
    deprecated.
  - for performances reasons, the number of characters added to a request or to
    a response is limited to 4096 since version 1.1.5 (it was 256 before). This
    value is easy to modify in the code if needed (#define). If it is too short
    on occasional uses, it is possible to gain some space by removing some
    useless headers before adding new ones.
  - a denied request will generate an "HTTP 403 forbidden" response, while a
    denied response will generate an "HTTP 502 Bad gateway" response.
    

Examples :
----------
        ###### a few examples ######

        # rewrite 'online.fr' instead of 'free.fr' for GET and POST requests
        reqrep        ^(GET\ .*)(.free.fr)(.*) \1.online.fr\3
        reqrep        ^(POST\ .*)(.free.fr)(.*) \1.online.fr\3

        # force proxy connections to close
        reqirep       ^Proxy-Connection:.*   Proxy-Connection:\ close
        # rewrite locations
        rspirep       ^(Location:\ )([^:]*://[^/]*)(.*) \1\3

        ###### A full configuration being used on production ######

        # Every header should end with a colon followed by one space.
        reqideny      ^[^:\ ]*[\ ]*$

        # block Apache chunk exploit
        reqideny      ^Transfer-Encoding:[\ ]*chunked
        reqideny      ^Host:\ apache-

        # block annoying worms that fill the logs...
        reqideny      ^[^:\ ]*\ .*(\.|%2e)(\.|%2e)(%2f|%5c|/|\\\\)
        reqideny      ^[^:\ ]*\ ([^\ ]*\ [^\ ]*\ |.*%00)
        reqideny      ^[^:\ ]*\ .*<script
        reqideny      ^[^:\ ]*\ .*/(root\.exe\?|cmd\.exe\?|default\.ida\?)

        # allow other syntactically valid requests, and block any other method
        reqipass      ^(GET|POST|HEAD|OPTIONS)\ /.*\ HTTP/1\.[01]$
        reqipass      ^OPTIONS\ \\*\ HTTP/1\.[01]$
        reqideny      ^[^:\ ]*\ 

        # force connection:close, thus disabling HTTP keep-alive
        option        httpclose

        # change the server name
        rspidel       ^Server:\ 
        rspadd        Server:\ Formilux/0.1.8


Also, the 'forwardfor' option creates an HTTP 'X-Forwarded-For' header which
contains the client's IP address. This is useful to let the final web server
know what the client address was (eg for statistics on domains).

Last, the 'httpclose' option removes any 'Connection' header both ways, and
adds a 'Connection: close' header in each direction. This makes it easier to
disable HTTP keep-alive than the previous 4-rules block.

Example :
---------
    listen http_proxy 0.0.0.0:80
        mode http
        log  global
        option httplog
        option dontlognull
        option forwardfor
        option httpclose

Note that some HTTP servers do not necessarily close the connections when they
receive the 'Connection: close', and if the client does not close either, then
the connection will be maintained up to the time-out. This translates into high
number of simultaneous sessions and high global session times in the logs. To
workaround this, a new option 'forceclose' appeared in version 1.2.9 to enforce
the closing of the outgoing server channel as soon as the server begins to
reply and only if the request buffer is empty. Note that this should NOT be
used if CONNECT requests are expected between the client and the server. The
'forceclose' option implies the 'httpclose' option.

Example :
---------
    listen http_proxy 0.0.0.0:80
        mode http
        log  global
        option httplog
        option dontlognull
        option forwardfor
        option forceclose


4.4) Load balancing with persistence
------------------------------------
Combining cookie insertion with internal load balancing allows to transparently
bring persistence to applications. The principle is quite simple :
  - assign a cookie value to each server
  - enable the load balancing between servers
  - insert a cookie into responses resulting from the balancing algorithm
    (indirect accesses), end ensure that no upstream proxy will cache it.
  - remove the cookie in the request headers so that the application never sees
    it.

Example :
---------
    listen application 0.0.0.0:80
        mode http
        cookie SERVERID insert nocache indirect
        balance roundrobin
        server srv1 192.168.1.1:80 cookie server01 check
        server srv2 192.168.1.2:80 cookie server02 check

The other solution brought by versions 1.1.30 and 1.2.3 is to reuse a cookie
from the server, and prefix the server's name to it. In this case, don't forget
to force "httpclose" mode so that you can be assured that every subsequent
request will have its cookie fixed.

    listen application 0.0.0.0:80
        mode http
        cookie JSESSIONID prefix
        balance roundrobin
        server srv1 192.168.1.1:80 cookie srv1 check
        server srv2 192.168.1.2:80 cookie srv2 check
        option httpclose


4.5) Protection against information leak from the servers
---------------------------------------------------------
In versions 1.1.28/1.2.1, a new option 'checkcache' was created. It carefully
checks 'Cache-control', 'Pragma' and 'Set-cookie' headers in server response
to check if there's a risk of caching a cookie on a client-side proxy. When this
option is enabled, the only responses which can be delivered to the client are :
  - all those without 'Set-Cookie' header ;
  - all those with a return code other than 200, 203, 206, 300, 301, 410,
    provided that the server has not set a 'Cache-control: public' header ;
  - all those that come from a POST request, provided that the server has not
    set a 'Cache-Control: public' header ;
  - those with a 'Pragma: no-cache' header
  - those with a 'Cache-control: private' header
  - those with a 'Cache-control: no-store' header
  - those with a 'Cache-control: max-age=0' header
  - those with a 'Cache-control: s-maxage=0' header
  - those with a 'Cache-control: no-cache' header
  - those with a 'Cache-control: no-cache="set-cookie"' header
  - those with a 'Cache-control: no-cache="set-cookie,' header
    (allowing other fields after set-cookie)

If a response doesn't respect these requirements, then it will be blocked just
as if it was from an 'rspdeny' filter, with an "HTTP 502 bad gateway". The
session state shows "PH--" meaning that the proxy blocked the response during
headers processing. Additionnaly, an alert will be sent in the logs so that
admins are told that there's something to be done.


4.6) Customizing errors
-----------------------
Some situations can make haproxy return an HTTP error code to the client :
  - invalid or too long request => HTTP 400
  - request not completely sent in time => HTTP 408
  - forbidden request (matches a deny filter) => HTTP 403
  - internal error in haproxy => HTTP 500
  - the server returned an invalid or incomplete response => HTTP 502
  - no server was available to handle the request => HTTP 503
  - the server failed to reply in time => HTTP 504

A succint error message taken from the RFC accompanies these return codes.
But depending on the clients knowledge, it may be better to return custom, user
friendly, error pages. This is made possible through the use of the 'errorloc'
command :

    errorloc <HTTP_code> <location>

Instead of generating an HTTP error <HTTP_code> among those above, the proxy
will return a temporary redirection code (HTTP 302) towards the address
specified in <location>. This address may be either relative to the site or
absolute. Since this request will be handled by the client's browser, it's
mandatory that the returned address be reachable from the outside.

Example :
---------
    listen application 0.0.0.0:80
        errorloc 400 /badrequest.html
        errorloc 403 /forbidden.html
        errorloc 408 /toolong.html
        errorloc 500 http://haproxy.domain.net/bugreport.html
        errorloc 502 http://192.168.114.58/error50x.html
        errorloc 503 http://192.168.114.58/error50x.html
        errorloc 504 http://192.168.114.58/error50x.html

Note: RFC2616 says that a client must reuse the same method to fetch the
Location returned by a 302, which causes problems with the POST method.
The return code 303 was designed explicitly to force the client to fetch the
Location URL with the GET method, but there are some browsers pre-dating
HTTP/1.1 which don't support it. Anyway, most browsers still behave with 302 as
if it was a 303. In order to allow the user to chose, versions 1.1.31 and 1.2.5
bring two new keywords to replace 'errorloc' : 'errorloc302' and 'errorloc303'.

They are preffered over errorloc (which still does 302). Consider using
errorloc303 everytime you know that your clients support HTTP 303 responses..


4.7) Modifying default values
-----------------------------
Version 1.1.22 introduced the notion of default values, which eliminates the
pain of often repeating common parameters between many instances, such as
logs, timeouts, modes, etc...

Default values are set in a 'defaults' section. Each of these section clears
all previously set default parameters, so there may be as many default
parameters as needed. Only the last one before a 'listen' section will be
used for this section. The 'defaults' section uses the same syntax as the
'listen' section, for the supported parameters. The 'defaults' keyword ignores
everything on its command line, so that fake instance names can be specified
there for better clarity.

In version 1.1.28/1.2.1, only those parameters can be preset in the 'default'
section :
  - log (the first and second one)
  - mode { tcp, http, health }
  - balance { roundrobin }
  - disabled (to disable every further instances)
  - enabled (to enable every further instances, this is the default)
  - contimeout, clitimeout, srvtimeout, grace, retries, maxconn
  - option { redispatch, transparent, keepalive, forwardfor, logasap, httpclose,
             checkcache, httplog, tcplog, dontlognull, persist, httpchk }
  - redispatch, redisp, transparent, source { addr:port }
  - cookie, capture
  - errorloc

As of 1.1.24, it is not possible to put certain parameters in a 'defaults'
section, mainly regular expressions and server configurations :
  - dispatch, server,
  - req*, rsp*

Last, there's no way yet to change a boolean option from its assigned default
value. So if an 'option' statement is set in a 'defaults' section, the only
way to flush it is to redefine a new 'defaults' section without this 'option'.

Examples :
----------
    defaults applications TCP
        log global
        mode tcp
        balance roundrobin
        clitimeout 180000
        srvtimeout 180000
        contimeout 4000
        retries 3
        redispatch

    listen app_tcp1 10.0.0.1:6000-6063
        server srv1 192.168.1.1 check port 6000 inter 10000
        server srv2 192.168.1.2 backup

    listen app_tcp2 10.0.0.2:6000-6063
        server srv1 192.168.2.1 check port 6000 inter 10000
        server srv2 192.168.2.2 backup
    
    defaults applications HTTP
        log global
        mode http
        option httplog
        option forwardfor
        option dontlognull
        balance roundrobin
        clitimeout 20000
        srvtimeout 20000
        contimeout 4000
        retries 3

    listen app_http1 10.0.0.1:80-81
        cookie SERVERID postonly insert indirect
        capture cookie userid= len 10
        server srv1 192.168.1.1:+8000 cookie srv1 check port 8080 inter 1000
        server srv1 192.168.1.2:+8000 cookie srv2 check port 8080 inter 1000

    defaults
        # this empty section voids all default parameters


4.8) Status report in HTML page
-------------------------------
Starting with 1.2.14, it is possible for HAProxy to intercept requests for a
particular URI and return a full report of the proxy's activity and servers
statistics. This is available through the 'stats' keyword, associated to any
such options :

   - stats enable
   - stats uri <uri prefix>
   - stats realm <authentication realm>
   - stats auth <user:password>
   - stats scope <proxy_id> | '.'

By default, the status report is disabled. Specifying any combination above
enables it for the proxy instance referencing it. The easiest solution is to
use "stats enable" which will enable the report with default parameters :

   - default URI   : "/haproxy?stats"        (CONFIG_STATS_DEFAULT_URI)
   - default auth  : unspecified (no authentication)
   - default realm : "HAProxy Statistics"    (CONFIG_STATS_DEFAULT_REALM)
   - default scope : unspecified (access to all instances)

The "stats uri <uri_prefix>" option allows one to intercept another URI prefix.
Note that any URI that BEGINS with this string will match. For instance, one
proxy instance might be dedicated to status page only and would reply to any
URI.

Example :
---------
    # catches any URI and returns the status page.
    listen stats :8080
        mode http
        stats uri /

The "stats auth <user:password>" option enables Basic authentication and adds a
valid user:password combination to the list of authorized accounts. The user
and password are passed in the configuration file as clear text, and since this
is HTTP Basic authentication, you should be aware that it transits as clear
text on the network, so you must not use any sensible account. The list is
unlimited in order to provide easy accesses to developpers or customers.

The "stats realm <realm>" option defines the "realm" name which is displayed
in the popup box when the browser asks for a password. It's important to ensure
that this one is not used by the application, otherwise the browser will try to
use a cached one from the application. Note that any space in the realm name
should be escaped with a backslash ('\').

The "stats scope <proxy_id>" option limits the scope of the status report. By
default, all proxy instances are listed. But under some circumstances, it would
be better to limit the listing to some proxies or only to the current one. This
is what this option does. The special proxy name "." (a single dot) references
the current proxy. The proxy name can be repeated multiple times, even for
proxies defined later in the configuration or some which do not exist. The name
is the one which appears after the 'listen' keyword.

Example :
---------
    # simple application with authenticated embedded status report
    listen app1 192.168.1.100:80
        mode http
        balance roundrobin
        cookie SERVERID postonly insert indirect
        server srv1 192.168.1.1:8080 cookie srv1 check inter 1000
        server srv1 192.168.1.2:8080 cookie srv2 check inter 1000
        stats uri /my_stats
	stats realm Statistics\ for\ MyApp1-2
	stats auth guest:guest
	stats auth admin:AdMiN123
	stats scope .
	stats scope app2

    # simple application with anonymous embedded status report
    listen app2 192.168.2.100:80
        mode http
        balance roundrobin
        cookie SERVERID postonly insert indirect
        server srv1 192.168.2.1:8080 cookie srv1 check inter 1000
        server srv1 192.168.2.2:8080 cookie srv2 check inter 1000
        stats uri /my_stats
	stats realm Statistics\ for\ MyApp2
	stats scope .

    listen admin_page :8080
        mode http
        stats uri /my_stats
	stats realm Global\ statistics
	stats auth admin:AdMiN123

Notes :
-------
  - The 'stats' options can also be specified in the 'defaults' section, in
    which case it will provide the exact same configuration to all further
    instances (hence the usefulness of the scope "."). However, if an instance
    redefines any 'stats' parameter, defaults will not be used for this
    instance.

  - HTTP Basic authentication is very basic and unsecure from snooping. No
    sensible password should be used, and be aware that there is no way to
    remove it from the browser so it will be sent to the whole application
    upon further accesses.


=========================
| System-specific setup |
=========================

Linux 2.4
=========

-- cut here --
#!/bin/sh
# set this to about 256/4M (16384 for 256M machine)
MAXFILES=16384
echo $MAXFILES > /proc/sys/fs/file-max
ulimit -n $MAXFILES

if [ -e /proc/sys/net/ipv4/ip_conntrack_max ]; then
        echo 65536 > /proc/sys/net/ipv4/ip_conntrack_max
fi

if [ -e /proc/sys/net/ipv4/netfilter/ip_ct_tcp_timeout_fin_wait ]; then
        # 30 seconds for fin, 15 for time wait
        echo 3000 > /proc/sys/net/ipv4/netfilter/ip_ct_tcp_timeout_fin_wait
        echo 1500 > /proc/sys/net/ipv4/netfilter/ip_ct_tcp_timeout_time_wait
        echo 0 > /proc/sys/net/ipv4/netfilter/ip_ct_tcp_log_invalid_scale
        echo 0 > /proc/sys/net/ipv4/netfilter/ip_ct_tcp_log_out_of_window
fi

echo 1024 60999 > /proc/sys/net/ipv4/ip_local_port_range
echo 30 > /proc/sys/net/ipv4/tcp_fin_timeout
echo 4096 > /proc/sys/net/ipv4/tcp_max_syn_backlog
echo 262144 > /proc/sys/net/ipv4/tcp_max_tw_buckets
echo 262144 > /proc/sys/net/ipv4/tcp_max_orphans
echo 300 > /proc/sys/net/ipv4/tcp_keepalive_time
echo 1 > /proc/sys/net/ipv4/tcp_tw_recycle
echo 0 > /proc/sys/net/ipv4/tcp_timestamps
echo 0 > /proc/sys/net/ipv4/tcp_ecn
echo 1 > /proc/sys/net/ipv4/tcp_sack
echo 0 > /proc/sys/net/ipv4/tcp_dsack

# auto-tuned on 2.4
#echo 262143 > /proc/sys/net/core/rmem_max
#echo 262143 > /proc/sys/net/core/rmem_default

echo 16384 65536 524288 > /proc/sys/net/ipv4/tcp_rmem
echo 16384 349520 699040 > /proc/sys/net/ipv4/tcp_wmem

-- cut here --


FreeBSD
=======

A FreeBSD port of HA-Proxy is now available and maintained, thanks to
Clement Laforet <sheepkiller@cultdeadsheep.org>.

For more information :
http://www.freebsd.org/cgi/url.cgi?ports/net/haproxy/pkg-descr
http://www.freebsd.org/cgi/cvsweb.cgi/ports/net/haproxy/
http://www.freshports.org/net/haproxy


-- end --