blob: de741901f86b25713d85f3ef81492f0360f02144 [file] [log] [blame]
developer3abe1ad2022-01-24 11:13:32 +08001#!/bin/ash
2
developer071927d2022-08-31 20:39:29 +08003interface=$1 # phy0/phy1/ra0
developerf90c9af2022-12-28 22:40:23 +08004cmd_type=$2 # set/show/e2p/mac/dump
developer3abe1ad2022-01-24 11:13:32 +08005full_cmd=$3
developer9b7cdad2022-03-10 14:24:55 +08006interface_ori=${interface}
developerf90c9af2022-12-28 22:40:23 +08007SOC_start_idx="0"
developerb4b29472023-01-06 19:07:21 +08008SOC_end_idx="0"
developerf90c9af2022-12-28 22:40:23 +08009is_eagle="0"
developer3abe1ad2022-01-24 11:13:32 +080010
11work_mode="RUN" # RUN/PRINT/DEBUG
developer679a6aa2022-09-07 09:52:41 +080012iwpriv_file="/tmp/iwpriv_wrapper"
13interface_file="/tmp/interface"
developer3abe1ad2022-01-24 11:13:32 +080014phy_idx=$(echo ${interface} | tr -dc '0-9')
15
developer3abe1ad2022-01-24 11:13:32 +080016function do_cmd() {
17 case ${work_mode} in
18 "RUN")
19 eval "$1"
20 ;;
21 "PRINT")
22 echo "$1"
23 ;;
24 "DEBUG")
developer3abe1ad2022-01-24 11:13:32 +080025 echo "$1"
developer887da632022-10-28 09:35:38 +080026 eval "$1"
developer3abe1ad2022-01-24 11:13:32 +080027 ;;
28 esac
29}
30
developer9b7cdad2022-03-10 14:24:55 +080031function print_debug() {
32 if [ "${work_mode}" = "DEBUG" ]; then
33 echo "$1"
34 fi
35}
36
developer10946c32022-03-04 18:28:43 +080037function write_dmesg() {
38 echo "$1" > /dev/kmsg
39}
40
developer3abe1ad2022-01-24 11:13:32 +080041function record_config() {
developer679a6aa2022-09-07 09:52:41 +080042 local config=$1
43 local tmp_file=$3
44
developerf90c9af2022-12-28 22:40:23 +080045 # check it is SOC(mt7986)/Eagle or PCIE card (mt7915/7916), and write its config
developerb4b29472023-01-06 19:07:21 +080046 if [ ${tmp_file} != ${interface_file} ]; then
developerf90c9af2022-12-28 22:40:23 +080047 if [ $phy_idx -lt $SOC_start_idx ]; then
developer679a6aa2022-09-07 09:52:41 +080048 config="${config}_PCIE"
developerf90c9af2022-12-28 22:40:23 +080049 elif [ $phy_idx -ge $SOC_start_idx ]; then
50 config="${config}_SOC"
developer679a6aa2022-09-07 09:52:41 +080051 fi
52 fi
53
developer3abe1ad2022-01-24 11:13:32 +080054 if [ -f ${tmp_file} ]; then
developer679a6aa2022-09-07 09:52:41 +080055 if grep -q ${config} ${tmp_file}; then
56 sed -i "/${config}/c\\${config}=$2" ${tmp_file}
developer3abe1ad2022-01-24 11:13:32 +080057 else
developer679a6aa2022-09-07 09:52:41 +080058 echo "${config}=$2" >> ${tmp_file}
developer3abe1ad2022-01-24 11:13:32 +080059 fi
60 else
developer679a6aa2022-09-07 09:52:41 +080061 echo "${config}=$2" >> ${tmp_file}
developer3abe1ad2022-01-24 11:13:32 +080062 fi
63}
64
65function get_config() {
developer679a6aa2022-09-07 09:52:41 +080066 local config=$1
67 local tmp_file=$2
68
developer10946c32022-03-04 18:28:43 +080069 if [ ! -f ${tmp_file} ]; then
70 echo ""
71 return
72 fi
73
developerf90c9af2022-12-28 22:40:23 +080074 # check it is SOC(mt7986)/Eagle or PCIE card (mt7915/7916), and write its config
developerb4b29472023-01-06 19:07:21 +080075 if [ ${tmp_file} != ${interface_file} ]; then
developerf90c9af2022-12-28 22:40:23 +080076 if [ $phy_idx -lt $SOC_start_idx ]; then
developer679a6aa2022-09-07 09:52:41 +080077 config="${config}_PCIE"
developerf90c9af2022-12-28 22:40:23 +080078 elif [ $phy_idx -ge $SOC_start_idx ]; then
79 config="${config}_SOC"
developer679a6aa2022-09-07 09:52:41 +080080 fi
81 fi
82
83 if grep -q ${config} ${tmp_file}; then
84 echo "$(cat ${tmp_file} | grep ${config} | sed s/=/' '/g | cut -d " " -f 2)"
developer10946c32022-03-04 18:28:43 +080085 else
86 echo ""
87 fi
developer3abe1ad2022-01-24 11:13:32 +080088}
89
developerb4b29472023-01-06 19:07:21 +080090function parse_sku {
developerf90c9af2022-12-28 22:40:23 +080091 SOC_start_idx=$(get_config "STARTIDX" ${interface_file})
developerb4b29472023-01-06 19:07:21 +080092 SOC_end_idx=$(get_config "ENDIDX" ${interface_file})
developerf90c9af2022-12-28 22:40:23 +080093 is_eagle=$(get_config "IS_EAGLE" ${interface_file})
developer679a6aa2022-09-07 09:52:41 +080094 local eeprom_file=/sys/kernel/debug/ieee80211/phy0/mt76/eeprom
developerb4b29472023-01-06 19:07:21 +080095 if [ -z "${SOC_start_idx}" ] || [ -z "${SOC_end_idx}" ] || [ -z "${is_eagle}" ]; then
developer679a6aa2022-09-07 09:52:41 +080096 if [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7916")" ]; then
developerf90c9af2022-12-28 22:40:23 +080097 SOC_start_idx="2"
developerb4b29472023-01-06 19:07:21 +080098 SOC_end_idx="3"
developerf90c9af2022-12-28 22:40:23 +080099 is_eagle="0"
developer679a6aa2022-09-07 09:52:41 +0800100 elif [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7915")" ]; then
developerf90c9af2022-12-28 22:40:23 +0800101 SOC_start_idx="1"
developerb4b29472023-01-06 19:07:21 +0800102 SOC_end_idx="2"
developerf90c9af2022-12-28 22:40:23 +0800103 is_eagle="0"
developer679a6aa2022-09-07 09:52:41 +0800104 elif [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7986")" ]; then
developerf90c9af2022-12-28 22:40:23 +0800105 SOC_start_idx="0"
developerb4b29472023-01-06 19:07:21 +0800106 SOC_end_idx="1"
developerf90c9af2022-12-28 22:40:23 +0800107 is_eagle="0"
108 elif [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7990")" ]; then
109 SOC_start_idx="0"
developerb4b29472023-01-06 19:07:21 +0800110 SOC_end_idx="2"
developerf90c9af2022-12-28 22:40:23 +0800111 is_eagle="1"
developereebce5c2022-08-26 19:05:56 +0800112 else
developer679a6aa2022-09-07 09:52:41 +0800113 echo "Interface Conversion Failed!"
114 echo "Please use iwpriv <phy0/phy1/..> set <...> or configure the sku of your board manually by the following commands"
developerb4b29472023-01-06 19:07:21 +0800115 echo "For AX6000:"
116 echo " echo STARTIDX=0 >> ${interface_file}"
117 echo " echo ENDIDX=1 >> ${interface_file}"
118 echo " echo IS_EAGLE=0 >> ${interface_file}"
119 echo "For AX7800:"
120 echo " echo STARTIDX=2 >> ${interface_file}"
121 echo " echo ENDIDX=3 >> ${interface_file}"
122 echo " echo IS_EAGLE=0 >> ${interface_file}"
123 echo "For AX8400:"
124 echo " echo STARTIDX=1 >> ${interface_file}"
125 echo " echo ENDIDX=2 >> ${interface_file}"
126 echo " echo IS_EAGLE=0 >> ${interface_file}"
127 echo "For Eagle:"
128 echo " echo STARTIDX=1 >> ${interface_file}"
129 echo " echo ENDIDX=2 >> ${interface_file}"
130 echo " echo IS_EAGLE=1 >> ${interface_file}"
developer679a6aa2022-09-07 09:52:41 +0800131 exit 0
developereebce5c2022-08-26 19:05:56 +0800132 fi
developerf90c9af2022-12-28 22:40:23 +0800133 record_config "STARTIDX" ${SOC_start_idx} ${interface_file}
developerb4b29472023-01-06 19:07:21 +0800134 record_config "ENDIDX" ${SOC_end_idx} ${interface_file}
developerf90c9af2022-12-28 22:40:23 +0800135 record_config "IS_EAGLE" ${is_eagle} ${interface_file}
developereebce5c2022-08-26 19:05:56 +0800136 fi
developerb4b29472023-01-06 19:07:21 +0800137}
developer679a6aa2022-09-07 09:52:41 +0800138
developerb4b29472023-01-06 19:07:21 +0800139function convert_interface {
developerf90c9af2022-12-28 22:40:23 +0800140 if [ ${is_eagle} == "0" ]; then
developer679a6aa2022-09-07 09:52:41 +0800141 if [[ $1 == "raix"* ]]; then
developerf90c9af2022-12-28 22:40:23 +0800142 phy_idx=1
143 elif [[ $1 == "rai"* ]]; then
developer679a6aa2022-09-07 09:52:41 +0800144 phy_idx=0
145 elif [[ $1 == "rax"* ]]; then
developerf90c9af2022-12-28 22:40:23 +0800146 phy_idx=$((SOC_start_idx+1))
147 else
148 phy_idx=$SOC_start_idx
developer679a6aa2022-09-07 09:52:41 +0800149 fi
developerf90c9af2022-12-28 22:40:23 +0800150
151 # convert phy index according to band idx
152 local band_idx=$(get_config "ATECTRLBANDIDX" ${iwpriv_file})
153 if [ "${band_idx}" = "0" ]; then
154 if [[ $1 == "raix"* ]]; then
155 phy_idx=0
156 elif [[ $1 == "rax"* ]]; then
157 phy_idx=$SOC_start_idx
158 fi
159 elif [ "${band_idx}" = "1" ]; then
160 if [[ $1 == "rai"* ]]; then
161 # AX8400: mt7915 remain phy0
162 # AX7800: mt7916 becomes phy1
163 phy_idx=$((SOC_start_idx-1))
164 elif [[ $1 == "ra"* ]]; then
165 phy_idx=$((SOC_start_idx+1))
166 fi
167 fi
168 else
169 # Eagle has different mapping method
170 # phy0: ra0
171 # phy1: rai0
172 # phy2: rax0
developer679a6aa2022-09-07 09:52:41 +0800173 if [[ $1 == "rai"* ]]; then
developerf90c9af2022-12-28 22:40:23 +0800174 phy_idx=1
175 elif [[ $1 == "rax"* ]]; then
176 phy_idx=2
177 else
178 phy_idx=0
developer679a6aa2022-09-07 09:52:41 +0800179 fi
180 fi
181
182 interface="phy${phy_idx}"
183}
184
185function change_band_idx {
186 local new_idx=$1
187 local new_phy_idx=$phy_idx
188
189 local old_idx=$(get_config "ATECTRLBANDIDX" ${iwpriv_file})
190
191
192 if [[ ${interface_ori} == "ra"* ]]; then
193 if [ -z "${old_idx}" ] || [ "${old_idx}" != "${new_idx}" ]; then
194 if [ "${new_idx}" = "0" ]; then
195 # raix0 & rai0 becomes rai0
196 if [[ $interface_ori == "rai"* ]]; then
197 new_phy_idx=0
198 # rax0 & ra0 becomes ra0
199 elif [[ $interface_ori == "ra"* ]]; then
developerf90c9af2022-12-28 22:40:23 +0800200 new_phy_idx=$SOC_start_idx
developer679a6aa2022-09-07 09:52:41 +0800201 fi
202 elif [ "${new_idx}" = "1" ]; then
203 # raix0 & rai0 becomes raix0
204 if [[ $interface_ori == "rai"* ]]; then
developer1346ce52022-12-15 21:36:14 +0800205 # For AX8400 => don't change phy idx
developerf90c9af2022-12-28 22:40:23 +0800206 if [ ${SOC_start_idx} != "1" ]; then
developer1346ce52022-12-15 21:36:14 +0800207 new_phy_idx=1
208 fi
developer679a6aa2022-09-07 09:52:41 +0800209 # rax0 & ra0 becomes rax0
210 elif [[ $interface_ori == "ra"* ]]; then
developerf90c9af2022-12-28 22:40:23 +0800211 new_phy_idx=$((SOC_start_idx+1))
developer679a6aa2022-09-07 09:52:41 +0800212 fi
213 fi
214 fi
215
216 if [ ${new_phy_idx} != ${phy_idx} ]; then
217 do_ate_work "ATESTOP"
218 phy_idx=$new_phy_idx
219 interface="phy${phy_idx}"
220 do_ate_work "ATESTART"
221 fi
developereebce5c2022-08-26 19:05:56 +0800222 fi
developer679a6aa2022-09-07 09:52:41 +0800223 record_config "ATECTRLBANDIDX" ${new_idx} ${iwpriv_file}
developereebce5c2022-08-26 19:05:56 +0800224}
225
developer3abe1ad2022-01-24 11:13:32 +0800226function simple_convert() {
227 if [ "$1" = "ATETXCNT" ]; then
228 echo "tx_count"
229 elif [ "$1" = "ATETXLEN" ]; then
230 echo "tx_length"
231 elif [ "$1" = "ATETXMCS" ]; then
232 echo "tx_rate_idx"
233 elif [ "$1" = "ATEVHTNSS" ]; then
234 echo "tx_rate_nss"
235 elif [ "$1" = "ATETXLDPC" ]; then
236 echo "tx_rate_ldpc"
237 elif [ "$1" = "ATETXSTBC" ]; then
238 echo "tx_rate_stbc"
239 elif [ "$1" = "ATEPKTTXTIME" ]; then
240 echo "tx_time"
241 elif [ "$1" = "ATEIPG" ]; then
242 echo "tx_ipg"
243 elif [ "$1" = "ATEDUTYCYCLE" ]; then
244 echo "tx_duty_cycle"
245 elif [ "$1" = "ATETXFREQOFFSET" ]; then
246 echo "freq_offset"
247 else
developer679a6aa2022-09-07 09:52:41 +0800248 echo "undefined"
developer3abe1ad2022-01-24 11:13:32 +0800249 fi
250}
251
252function convert_tx_mode() {
developer1346ce52022-12-15 21:36:14 +0800253 # Remove leading zeros
developer4feb1012023-01-30 17:29:07 +0800254 local tx_mode=$(echo $1 | sed -r 's/0+([0-9]+)/\1/g')
developer1346ce52022-12-15 21:36:14 +0800255
256 if [ "$tx_mode" = "0" ]; then
developer3abe1ad2022-01-24 11:13:32 +0800257 echo "cck"
developer1346ce52022-12-15 21:36:14 +0800258 elif [ "$tx_mode" = "1" ]; then
developer3abe1ad2022-01-24 11:13:32 +0800259 echo "ofdm"
developer1346ce52022-12-15 21:36:14 +0800260 elif [ "$tx_mode" = "2" ]; then
developer3abe1ad2022-01-24 11:13:32 +0800261 echo "ht"
developer1346ce52022-12-15 21:36:14 +0800262 elif [ "$tx_mode" = "4" ]; then
developer3abe1ad2022-01-24 11:13:32 +0800263 echo "vht"
developer1346ce52022-12-15 21:36:14 +0800264 elif [ "$tx_mode" = "8" ]; then
developer3abe1ad2022-01-24 11:13:32 +0800265 echo "he_su"
developer1346ce52022-12-15 21:36:14 +0800266 elif [ "$tx_mode" = "9" ]; then
developer3abe1ad2022-01-24 11:13:32 +0800267 echo "he_er"
developer1346ce52022-12-15 21:36:14 +0800268 elif [ "$tx_mode" = "10" ]; then
developer3abe1ad2022-01-24 11:13:32 +0800269 echo "he_tb"
developer1346ce52022-12-15 21:36:14 +0800270 elif [ "$tx_mode" = "11" ]; then
developer3abe1ad2022-01-24 11:13:32 +0800271 echo "he_mu"
developercec48ac2023-03-01 17:00:33 +0800272 elif [ "$tx_mode" = "13" ]; then
273 echo "eht_su"
274 elif [ "$tx_mode" = "14" ]; then
275 echo "eht_tb"
276 elif [ "$tx_mode" = "15" ]; then
277 echo "eht_mu"
developer3abe1ad2022-01-24 11:13:32 +0800278 else
developer679a6aa2022-09-07 09:52:41 +0800279 echo "undefined"
developer3abe1ad2022-01-24 11:13:32 +0800280 fi
281}
282
283function convert_gi {
284 local tx_mode=$1
285 local val=$2
286 local sgi="0"
287 local he_ltf="0"
288
289 case ${tx_mode} in
290 "ht"|"vht")
291 sgi=${val}
292 ;;
293 "he_su"|"he_er")
294 case ${val} in
295 "0")
296 ;;
297 "1")
298 he_ltf="1"
299 ;;
300 "2")
301 sgi="1"
302 he_ltf="1"
303 ;;
304 "3")
305 sgi="2"
306 he_ltf="2"
307 ;;
308 "4")
309 he_ltf="2"
310 ;;
311 *)
312 echo "unknown gi"
313 esac
314 ;;
315 "he_mu")
316 case ${val} in
317 "0")
318 he_ltf="2"
319 ;;
320 "1")
321 he_ltf="1"
322 ;;
323 "2")
324 sgi="1"
325 he_ltf="1"
326 ;;
327 "3")
328 sgi="2"
329 he_ltf="2"
330 ;;
331 *)
332 echo "unknown gi"
333 esac
334 ;;
335 "he_tb")
336 case ${val} in
337 "0")
338 sgi="1"
339 ;;
340 "1")
341 sgi="1"
342 he_ltf="1"
343 ;;
344 "2")
345 sgi="2"
346 he_ltf="2"
347 ;;
348 *)
349 echo "unknown gi"
350 esac
351 ;;
352 *)
developer9b7cdad2022-03-10 14:24:55 +0800353 print_debug "legacy mode no need gi"
developer3abe1ad2022-01-24 11:13:32 +0800354 esac
355
356 do_cmd "mt76-test ${interface} set tx_rate_sgi=${sgi} tx_ltf=${he_ltf}"
357}
358
359function convert_channel {
developer679a6aa2022-09-07 09:52:41 +0800360 local ctrl_band_idx=$(get_config "ATECTRLBANDIDX" ${iwpriv_file})
developer3abe1ad2022-01-24 11:13:32 +0800361 local ch=$(echo $1 | sed s/:/' '/g | cut -d " " -f 1)
developer679a6aa2022-09-07 09:52:41 +0800362 local bw=$(get_config "ATETXBW" ${iwpriv_file} | cut -d ":" -f 1)
developer10946c32022-03-04 18:28:43 +0800363 local bw_str="HT20"
developereebce5c2022-08-26 19:05:56 +0800364 local base_chan=1
365 local control_freq=0
366 local base_freq=0
developer1346ce52022-12-15 21:36:14 +0800367 local band=$(echo $1 | sed s/:/' '/g | cut -d " " -f 2)
368 local temp=$((phy_idx+1))
developer3abe1ad2022-01-24 11:13:32 +0800369
developer1346ce52022-12-15 21:36:14 +0800370 # Handle ATECTRLBANDIDX
371 if [ ! -z ${ctrl_band_idx} ]; then
372 if [ "${ctrl_band_idx}" == "1" ] && [ ${band} == "0" ]; then
373 local temp=$(cat "/etc/config/wireless"| grep "option band" | sed -n ${temp}p | cut -c 15)
374 if [ "${temp}" == "2" ]; then
375 local band=0
376 elif [ "${temp}" == "5" ]; then
377 local band=1
378 elif [ "${temp}" == "6" ]; then
379 local band=2
380 else
381 echo "iwpriv wrapper band translate error!"
382 fi
383 else
384 # mt7915 in AX8400 case: band should be determined by only the input band
developerf90c9af2022-12-28 22:40:23 +0800385 if [ "${SOC_start_idx}" == "1" ] && [ ${phy_idx} == "0" ]; then
developer1346ce52022-12-15 21:36:14 +0800386 local band=$((band))
387 else
388 local band=$((ctrl_band_idx * band))
389 fi
390 fi
developer679a6aa2022-09-07 09:52:41 +0800391 fi
392
developer9b7cdad2022-03-10 14:24:55 +0800393 if [[ $1 != *":"* ]] || [ "${band}" = "0" ]; then
developer3abe1ad2022-01-24 11:13:32 +0800394 case ${bw} in
395 "1")
developer461cb542022-04-29 18:17:44 +0800396 if [ "${ch}" -lt "3" ] || [ "${ch}" -gt "12" ]; then
397 local bw_str="HT20"
developer3abe1ad2022-01-24 11:13:32 +0800398 else
developer461cb542022-04-29 18:17:44 +0800399 local bw_str="HT40+"
400 ch=$(expr ${ch} - "2")
developer3abe1ad2022-01-24 11:13:32 +0800401 fi
402 ;;
developer3abe1ad2022-01-24 11:13:32 +0800403 esac
developereebce5c2022-08-26 19:05:56 +0800404 local base_freq=2412
developera6267142022-01-26 20:50:22 +0800405 elif [ "${band}" = "1" ]; then
developer3abe1ad2022-01-24 11:13:32 +0800406 case ${bw} in
developera6267142022-01-26 20:50:22 +0800407 "5")
developer10946c32022-03-04 18:28:43 +0800408 bw_str="160MHz"
409 if [ ${ch} -lt "68" ]; then
410 ch="36"
411 elif [ ${ch} -lt "100" ]; then
412 ch="68"
413 elif [ ${ch} -lt "132" ]; then
414 ch="100"
415 elif [ ${ch} -lt "181" ]; then
416 ch="149"
417 fi
developera6267142022-01-26 20:50:22 +0800418 ;;
developer3abe1ad2022-01-24 11:13:32 +0800419 "2")
developer10946c32022-03-04 18:28:43 +0800420 bw_str="80MHz"
421 if [ ${ch} -lt "52" ]; then
422 ch="36"
423 elif [ ${ch} -lt "68" ]; then
424 ch="52"
425 elif [ ${ch} -lt "84" ]; then
426 ch="68"
427 elif [ ${ch} -lt "100" ]; then
428 ch="84"
429 elif [ ${ch} -lt "116" ]; then
430 ch="100"
431 elif [ ${ch} -lt "132" ]; then
432 ch="116"
433 elif [ ${ch} -lt "149" ]; then
434 ch="132"
435 elif [ ${ch} -lt "165" ]; then
436 ch="149"
437 elif [ ${ch} -lt "181" ]; then
438 ch="165"
439 fi
developer3abe1ad2022-01-24 11:13:32 +0800440 ;;
441 "1")
developer10946c32022-03-04 18:28:43 +0800442 if [ ${ch} -lt "44" ]; then
443 ch=$([ "${ch}" -lt "40" ] && echo "36" || echo "40")
444 bw_str=$([ "${ch}" -le "38" ] && echo "HT40+" || echo "HT40-")
445 elif [ ${ch} -lt "52" ]; then
446 ch=$([ "${ch}" -lt "48" ] && echo "44" || echo "48")
447 bw_str=$([ "${ch}" -le "46" ] && echo "HT40+" || echo "HT40-")
448 elif [ ${ch} -lt "60" ]; then
449 ch=$([ "${ch}" -lt "56" ] && echo "52" || echo "56")
450 bw_str=$([ "${ch}" -le "54" ] && echo "HT40+" || echo "HT40-")
451 elif [ ${ch} -lt "68" ]; then
452 ch=$([ "${ch}" -lt "64" ] && echo "60" || echo "64")
453 bw_str=$([ "${ch}" -le "62" ] && echo "HT40+" || echo "HT40-")
454 elif [ ${ch} -lt "76" ]; then
455 ch=$([ "${ch}" -lt "72" ] && echo "68" || echo "72")
456 bw_str=$([ "${ch}" -le "70" ] && echo "HT40+" || echo "HT40-")
457 elif [ ${ch} -lt "84" ]; then
458 ch=$([ "${ch}" -lt "80" ] && echo "76" || echo "80")
459 bw_str=$([ "${ch}" -le "78" ] && echo "HT40+" || echo "HT40-")
460 elif [ ${ch} -lt "92" ]; then
461 ch=$([ "${ch}" -lt "88" ] && echo "84" || echo "88")
462 bw_str=$([ "${ch}" -le "86" ] && echo "HT40+" || echo "HT40-")
463 elif [ ${ch} -lt "100" ]; then
464 ch=$([ "${ch}" -lt "96" ] && echo "92" || echo "96")
465 bw_str=$([ "${ch}" -le "94" ] && echo "HT40+" || echo "HT40-")
466 elif [ ${ch} -lt "108" ]; then
467 ch=$([ "${ch}" -lt "104" ] && echo "100" || echo "104")
468 bw_str=$([ "${ch}" -le "102" ] && echo "HT40+" || echo "HT40-")
469 elif [ ${ch} -lt "116" ]; then
470 ch=$([ "${ch}" -lt "112" ] && echo "108" || echo "112")
471 bw_str=$([ "${ch}" -le "110" ] && echo "HT40+" || echo "HT40-")
472 elif [ ${ch} -lt "124" ]; then
473 ch=$([ "${ch}" -lt "120" ] && echo "116" || echo "120")
474 bw_str=$([ "${ch}" -le "118" ] && echo "HT40+" || echo "HT40-")
475 elif [ ${ch} -lt "132" ]; then
476 ch=$([ "${ch}" -lt "128" ] && echo "124" || echo "128")
477 bw_str=$([ "${ch}" -le "126" ] && echo "HT40+" || echo "HT40-")
478 elif [ ${ch} -lt "140" ]; then
479 ch=$([ "${ch}" -lt "136" ] && echo "132" || echo "136")
480 bw_str=$([ "${ch}" -le "134" ] && echo "HT40+" || echo "HT40-")
481 elif [ ${ch} -lt "149" ]; then
482 ch=$([ "${ch}" -lt "144" ] && echo "140" || echo "144")
483 bw_str=$([ "${ch}" -le "142" ] && echo "HT40+" || echo "HT40-")
484 elif [ ${ch} -lt "157" ]; then
485 ch=$([ "${ch}" -lt "153" ] && echo "149" || echo "153")
486 bw_str=$([ "${ch}" -le "151" ] && echo "HT40+" || echo "HT40-")
487 elif [ ${ch} -lt "165" ]; then
488 ch=$([ "${ch}" -lt "161" ] && echo "157" || echo "161")
489 bw_str=$([ "${ch}" -le "159" ] && echo "HT40+" || echo "HT40-")
490 elif [ ${ch} -lt "173" ]; then
491 ch=$([ "${ch}" -lt "169" ] && echo "165" || echo "169")
492 bw_str=$([ "${ch}" -le "167" ] && echo "HT40+" || echo "HT40-")
493 elif [ ${ch} -lt "181" ]; then
494 ch=$([ "${ch}" -lt "177" ] && echo "173" || echo "177")
495 bw_str=$([ "${ch}" -le "175" ] && echo "HT40+" || echo "HT40-")
developer3abe1ad2022-01-24 11:13:32 +0800496 fi
497 ;;
498 "0")
499 local bw_str="HT20"
500 ;;
501 esac
developereebce5c2022-08-26 19:05:56 +0800502 local base_freq=5180
503 local base_chan=36
developera6267142022-01-26 20:50:22 +0800504 else
developercec48ac2023-03-01 17:00:33 +0800505 local base_freq=5955
developereebce5c2022-08-26 19:05:56 +0800506 case ${bw} in
developercec48ac2023-03-01 17:00:33 +0800507 "12")
508 local bw_str="320"
509 if [ ${ch} == "31" ]; then
510 local control_freq="5955"
511 elif [ ${ch} == "63" ]; then
512 local control_freq="6115"
513 elif [ ${ch} == "95" ]; then
514 local control_freq="6275"
515 elif [ ${ch} == "127" ]; then
516 local control_freq="6435"
517 elif [ ${ch} == "159" ]; then
518 local control_freq="6595"
519 elif [ ${ch} == "191" ]; then
520 local control_freq="6755"
521 fi
522 local center_freq=$(((ch - base_chan) * 5 + base_freq))
523 do_cmd "iw dev mon${phy_idx} set freq ${control_freq} ${bw_str} ${center_freq}"
524 return
525 ;;
developereebce5c2022-08-26 19:05:56 +0800526 "5")
527 bw_str="160MHz"
528 if [ ${ch} -lt "33" ]; then
529 ch="1"
530 elif [ ${ch} -lt "65" ]; then
531 ch="33"
532 elif [ ${ch} -lt "97" ]; then
533 ch="65"
534 elif [ ${ch} -lt "129" ]; then
535 ch="97"
536 elif [ ${ch} -lt "161" ]; then
537 ch="129"
538 elif [ ${ch} -lt "193" ]; then
539 ch="161"
540 elif [ ${ch} -lt "225" ]; then
541 ch="193"
542 fi
543 ;;
544 "2")
545 bw_str="80MHz"
546 if [ ${ch} -lt "17" ]; then
547 ch="1"
548 elif [ ${ch} -lt "33" ]; then
549 ch="17"
550 elif [ ${ch} -lt "49" ]; then
551 ch="33"
552 elif [ ${ch} -lt "65" ]; then
553 ch="49"
554 elif [ ${ch} -lt "81" ]; then
555 ch="65"
556 elif [ ${ch} -lt "97" ]; then
557 ch="81"
558 elif [ ${ch} -lt "113" ]; then
559 ch="97"
560 elif [ ${ch} -lt "129" ]; then
561 ch="113"
562 elif [ ${ch} -lt "145" ]; then
563 ch="129"
564 elif [ ${ch} -lt "161" ]; then
565 ch="145"
566 elif [ ${ch} -lt "177" ]; then
567 ch="161"
568 elif [ ${ch} -lt "193" ]; then
569 ch="177"
570 elif [ ${ch} -lt "209" ]; then
571 ch="193"
572 elif [ ${ch} -lt "225" ]; then
573 ch="209"
574 fi
575 ;;
576 "1")
577 if [ ${ch} -lt "9" ]; then
578 ch=$([ "${ch}" -lt "5" ] && echo "1" || echo "5")
579 bw_str=$([ "${ch}" -le "3" ] && echo "HT40+" || echo "HT40-")
580 elif [ ${ch} -lt "17" ]; then
581 ch=$([ "${ch}" -lt "13" ] && echo "9" || echo "13")
582 bw_str=$([ "${ch}" -le "11" ] && echo "HT40+" || echo "HT40-")
583 elif [ ${ch} -lt "25" ]; then
584 ch=$([ "${ch}" -lt "21" ] && echo "17" || echo "21")
585 bw_str=$([ "${ch}" -le "19" ] && echo "HT40+" || echo "HT40-")
586 elif [ ${ch} -lt "33" ]; then
587 ch=$([ "${ch}" -lt "29" ] && echo "25" || echo "29")
588 bw_str=$([ "${ch}" -le "27" ] && echo "HT40+" || echo "HT40-")
589 elif [ ${ch} -lt "33" ]; then
590 ch=$([ "${ch}" -lt "29" ] && echo "25" || echo "29")
591 bw_str=$([ "${ch}" -le "27" ] && echo "HT40+" || echo "HT40-")
592 elif [ ${ch} -lt "41" ]; then
593 ch=$([ "${ch}" -lt "37" ] && echo "33" || echo "37")
594 bw_str=$([ "${ch}" -le "35" ] && echo "HT40+" || echo "HT40-")
595 elif [ ${ch} -lt "49" ]; then
596 ch=$([ "${ch}" -lt "45" ] && echo "41" || echo "45")
597 bw_str=$([ "${ch}" -le "43" ] && echo "HT40+" || echo "HT40-")
598 elif [ ${ch} -lt "57" ]; then
599 ch=$([ "${ch}" -lt "53" ] && echo "49" || echo "53")
600 bw_str=$([ "${ch}" -le "51" ] && echo "HT40+" || echo "HT40-")
601 elif [ ${ch} -lt "65" ]; then
602 ch=$([ "${ch}" -lt "61" ] && echo "57" || echo "61")
603 bw_str=$([ "${ch}" -le "59" ] && echo "HT40+" || echo "HT40-")
604 elif [ ${ch} -lt "73" ]; then
605 ch=$([ "${ch}" -lt "69" ] && echo "65" || echo "69")
606 bw_str=$([ "${ch}" -le "67" ] && echo "HT40+" || echo "HT40-")
607 elif [ ${ch} -lt "81" ]; then
608 ch=$([ "${ch}" -lt "77" ] && echo "73" || echo "77")
609 bw_str=$([ "${ch}" -le "75" ] && echo "HT40+" || echo "HT40-")
610 elif [ ${ch} -lt "89" ]; then
611 ch=$([ "${ch}" -lt "85" ] && echo "81" || echo "85")
612 bw_str=$([ "${ch}" -le "83" ] && echo "HT40+" || echo "HT40-")
613 elif [ ${ch} -lt "97" ]; then
614 ch=$([ "${ch}" -lt "93" ] && echo "89" || echo "93")
615 bw_str=$([ "${ch}" -le "91" ] && echo "HT40+" || echo "HT40-")
616 elif [ ${ch} -lt "105" ]; then
617 ch=$([ "${ch}" -lt "101" ] && echo "97" || echo "101")
618 bw_str=$([ "${ch}" -le "99" ] && echo "HT40+" || echo "HT40-")
619 elif [ ${ch} -lt "113" ]; then
620 ch=$([ "${ch}" -lt "109" ] && echo "105" || echo "109")
621 bw_str=$([ "${ch}" -le "107" ] && echo "HT40+" || echo "HT40-")
622 elif [ ${ch} -lt "121" ]; then
623 ch=$([ "${ch}" -lt "117" ] && echo "113" || echo "117")
624 bw_str=$([ "${ch}" -le "115" ] && echo "HT40+" || echo "HT40-")
625 elif [ ${ch} -lt "129" ]; then
626 ch=$([ "${ch}" -lt "125" ] && echo "121" || echo "125")
627 bw_str=$([ "${ch}" -le "123" ] && echo "HT40+" || echo "HT40-")
628 elif [ ${ch} -lt "137" ]; then
629 ch=$([ "${ch}" -lt "133" ] && echo "129" || echo "133")
630 bw_str=$([ "${ch}" -le "131" ] && echo "HT40+" || echo "HT40-")
631 elif [ ${ch} -lt "145" ]; then
632 ch=$([ "${ch}" -lt "141" ] && echo "137" || echo "141")
633 bw_str=$([ "${ch}" -le "139" ] && echo "HT40+" || echo "HT40-")
634 elif [ ${ch} -lt "153" ]; then
635 ch=$([ "${ch}" -lt "149" ] && echo "145" || echo "149")
636 bw_str=$([ "${ch}" -le "147" ] && echo "HT40+" || echo "HT40-")
637 elif [ ${ch} -lt "161" ]; then
638 ch=$([ "${ch}" -lt "157" ] && echo "153" || echo "157")
639 bw_str=$([ "${ch}" -le "155" ] && echo "HT40+" || echo "HT40-")
640 elif [ ${ch} -lt "169" ]; then
641 ch=$([ "${ch}" -lt "165" ] && echo "161" || echo "165")
642 bw_str=$([ "${ch}" -le "163" ] && echo "HT40+" || echo "HT40-")
643 elif [ ${ch} -lt "177" ]; then
644 ch=$([ "${ch}" -lt "173" ] && echo "169" || echo "173")
645 bw_str=$([ "${ch}" -le "171" ] && echo "HT40+" || echo "HT40-")
646 elif [ ${ch} -lt "185" ]; then
647 ch=$([ "${ch}" -lt "181" ] && echo "177" || echo "181")
648 bw_str=$([ "${ch}" -le "179" ] && echo "HT40+" || echo "HT40-")
649 elif [ ${ch} -lt "193" ]; then
650 ch=$([ "${ch}" -lt "189" ] && echo "185" || echo "189")
651 bw_str=$([ "${ch}" -le "187" ] && echo "HT40+" || echo "HT40-")
652 elif [ ${ch} -lt "201" ]; then
653 ch=$([ "${ch}" -lt "197" ] && echo "193" || echo "197")
654 bw_str=$([ "${ch}" -le "195" ] && echo "HT40+" || echo "HT40-")
655 elif [ ${ch} -lt "209" ]; then
656 ch=$([ "${ch}" -lt "205" ] && echo "201" || echo "205")
657 bw_str=$([ "${ch}" -le "203" ] && echo "HT40+" || echo "HT40-")
658 elif [ ${ch} -lt "217" ]; then
659 ch=$([ "${ch}" -lt "213" ] && echo "209" || echo "213")
660 bw_str=$([ "${ch}" -le "211" ] && echo "HT40+" || echo "HT40-")
661 elif [ ${ch} -lt "225" ]; then
662 ch=$([ "${ch}" -lt "221" ] && echo "217" || echo "221")
663 bw_str=$([ "${ch}" -le "219" ] && echo "HT40+" || echo "HT40-")
664 elif [ ${ch} -lt "233" ]; then
665 ch=$([ "${ch}" -lt "229" ] && echo "225" || echo "229")
666 bw_str=$([ "${ch}" -le "227" ] && echo "HT40+" || echo "HT40-")
667 fi
668 ;;
669 "0")
670 local bw_str="HT20"
671 ;;
672 esac
developer3abe1ad2022-01-24 11:13:32 +0800673 fi
674
developereebce5c2022-08-26 19:05:56 +0800675 local control_freq=$(((ch - base_chan) * 5 + base_freq))
676 do_cmd "iw dev mon${phy_idx} set freq ${control_freq} ${bw_str}"
developer3abe1ad2022-01-24 11:13:32 +0800677}
678
developer10946c32022-03-04 18:28:43 +0800679function convert_rxstat {
680 local res=$(do_cmd "mt76-test ${interface} dump stats")
681 local mdrdy=$(echo "${res}" | grep "rx_packets" | cut -d "=" -f 2)
682 local fcs_error=$(echo "${res}" | grep "rx_fcs_error" | cut -d "=" -f 2)
683 local rcpi=$(echo "${res}" | grep "last_rcpi" | cut -d "=" -f 2 | sed 's/,/ /g')
684 local ib_rssi=$(echo "${res}" | grep "last_ib_rssi" | cut -d "=" -f 2 | sed 's/,/ /g')
685 local wb_rssi=$(echo "${res}" | grep "last_wb_rssi" | cut -d "=" -f 2 | sed 's/,/ /g')
686 local rx_ok=$(expr ${mdrdy} - ${fcs_error})
687
developer461cb542022-04-29 18:17:44 +0800688 write_dmesg "rcpi: ${rcpi}"
689 write_dmesg "fagc rssi ib: ${ib_rssi}"
690 write_dmesg "fagc rssi wb: ${wb_rssi}"
691 write_dmesg "all_mac_rx_mdrdy_cnt: ${mdrdy}"
692 write_dmesg "all_mac_rx_fcs_err_cnt: ${fcs_error}"
developer9b7cdad2022-03-10 14:24:55 +0800693 write_dmesg "all_mac_rx_ok_cnt : ${rx_ok}"
developer10946c32022-03-04 18:28:43 +0800694}
695
developer10946c32022-03-04 18:28:43 +0800696function set_mac_addr {
developer679a6aa2022-09-07 09:52:41 +0800697 record_config ${cmd} ${param} ${iwpriv_file}
developer10946c32022-03-04 18:28:43 +0800698
developer679a6aa2022-09-07 09:52:41 +0800699 local addr1=$(get_config "ATEDA" ${iwpriv_file})
700 local addr2=$(get_config "ATESA" ${iwpriv_file})
701 local addr3=$(get_config "ATEBSSID" ${iwpriv_file})
developer10946c32022-03-04 18:28:43 +0800702
703 if [ -z "${addr1}" ]; then
704 addr1="00:11:22:33:44:55"
705 fi
706 if [ -z "${addr2}" ]; then
707 addr2="00:11:22:33:44:55"
708 fi
709 if [ -z "${addr3}" ]; then
710 addr3="00:11:22:33:44:55"
711 fi
712
713 do_cmd "mt76-test phy${phy_idx} set mac_addrs=${addr1},${addr2},${addr3}"
714}
715
developerf9843e22022-09-13 10:57:15 +0800716function convert_ibf {
717 local cmd=$1
718 local param=$2
719 local new_cmd=""
720 local new_param=$(echo ${param} | sed s/":"/","/g)
721
722 case ${cmd} in
723 "ATETxBfInit")
724 new_cmd="init"
developer1346ce52022-12-15 21:36:14 +0800725 new_param="1"
726 do_cmd "mt76-test phy${phy_idx} set state=idle"
727 ;;
728 "ATETxBfGdInit")
729 new_cmd="golden_init"
730 new_param="1"
developerf9843e22022-09-13 10:57:15 +0800731 do_cmd "mt76-test phy${phy_idx} set state=idle"
732 ;;
733 "ATEIBFPhaseComp")
734 new_cmd="phase_comp"
developer1346ce52022-12-15 21:36:14 +0800735 new_param="${new_param}"
developerf9843e22022-09-13 10:57:15 +0800736 ;;
737 "ATEEBfProfileConfig")
738 new_cmd="ebf_prof_update"
739 ;;
740 "ATEIBfProfileConfig")
741 new_cmd="ibf_prof_update"
742 ;;
743 "ATEIBfInstCal")
744 new_cmd="phase_cal"
745 ;;
746 "ATEIBfGdCal")
747 new_cmd="phase_cal"
748 new_param="${new_param},00"
749 ;;
750 "TxBfTxApply")
751 new_cmd="apply_tx"
752 ;;
753 "ATETxPacketWithBf")
754 local bf_on=${new_param:0:2}
755 local aid="01"
756 local wlan_idx=${new_param:3:2}
757 local update="00"
758 local tx_len=${new_param:6}
759
760 new_cmd="tx_prep"
761 new_param="${bf_on},${aid},${wlan_idx},${update}"
762 if [ "${tx_len}" = "00" ]; then
763 new_param="${new_param} aid=1 tx_count=10000000 tx_length=1024"
764 else
765 new_param="${new_param} aid=1 tx_count=${tx_len} tx_length=1024"
766 fi
767 do_cmd "mt76-test phy${phy_idx} set state=idle"
768 ;;
769 "TxBfProfileData20MAllWrite")
770 new_cmd="prof_update_all"
771 ;;
772 "ATEIBFPhaseE2pUpdate")
773 new_cmd="e2p_update"
774 ;;
developer1346ce52022-12-15 21:36:14 +0800775 "ATEIBFPhaseVerify")
776 local group=${new_param:0:2}
777 local group_l_m_h=${new_param:3:2}
778 local band_idx=${new_param:6:2}
779 local phase_cal_type=${new_param:9:2}
780 local LNA_gain_level=${new_param:12:2}
781 local read_from_e2p=${new_param:15:2}
782
783 do_cmd "mt76-test phy${phy_idx} set txbf_act=phase_comp txbf_param=1,${band_idx},${group},${read_from_e2p},0"
784 new_cmd="phase_cal"
785 new_param="${group},${group_l_m_h},${band_idx},${phase_cal_type},${LNA_gain_level}"
786 ;;
787 "TxBfProfileTagRead")
788 new_cmd="pfmu_tag_read"
789 ;;
790 "TxBfProfileTagWrite")
791 new_cmd="pfmu_tag_write"
792 ;;
793 "TxBfProfileTagInValid")
794 new_cmd="set_invalid_prof"
795 ;;
796 "StaRecBfRead")
797 new_cmd="sta_rec_read"
798 ;;
799 "TriggerSounding")
800 new_cmd="trigger_sounding"
801 ;;
802 "StopSounding")
803 new_cmd="stop_sounding"
804 new_param="0"
805 ;;
806 "ATEConTxETxBfGdProc")
807 local tx_rate_mode=$(convert_tx_mode ${new_param:0:2})
808 local tx_rate_idx=${new_param:3:2}
809 local bw=$(echo ${new_param:6:2} | sed 's/^0//')
810 local channel=${new_param:9:3}
811 local channel2=${new_param:13:3}
812 local band=${new_param:17}
813
814 new_cmd="ebf_golden_init"
815 do_ate_work "ATESTART"
816 do_cmd "mt76-test phy${phy_idx} set state=idle"
817 record_config "ATETXBW" ${bw} ${iwpriv_file}
818 convert_channel "${channel}:${band}"
819 if [ "${bw}" = "5" ]; then
820 new_param="1,1"
821 else
822 new_param="1,0"
823 fi
824 do_cmd "mt76-test phy${phy_idx} set tx_rate_mode=${tx_rate_mode} tx_rate_idx=${tx_rate_idx} tx_rate_sgi=0"
825 ;;
826 "ATEConTxETxBfInitProc")
827 local tx_rate_mode=$(convert_tx_mode ${new_param:0:2})
828 local tx_rate_idx=${new_param:3:2}
829 local bw=$(echo ${new_param:6:2} | sed 's/^0//')
830 local tx_rate_nss=${new_param:9:2}
831 local tx_stream=${new_param:12:2}
832 local tx_power=${new_param:15:2}
833 local channel=${new_param:18:3}
834 local channel2=${new_param:22:3}
835 local band=${new_param:26:1}
836 local tx_length=${new_param:28:5}
837
838 new_cmd="ebf_init"
839 do_ate_work "ATESTART"
840 do_cmd "mt76-test phy${phy_idx} set state=idle"
841 record_config "ATETXBW" ${bw} ${iwpriv_file}
842 convert_channel "${channel}:${band}"
843 new_param="1"
844 do_cmd "mt76-test phy${phy_idx} set tx_rate_mode=${tx_rate_mode} tx_rate_idx=${tx_rate_idx} tx_rate_nss=${tx_rate_nss} tx_rate_sgi=0 tx_rate_ldpc=1 tx_power=${tx_power},0,0,0 tx_count=10000000 tx_length=${tx_length} tx_ipg=4"
845 ;;
developerf9843e22022-09-13 10:57:15 +0800846 *)
847 esac
848
849 do_cmd "mt76-test phy${phy_idx} set txbf_act=${new_cmd} txbf_param=${new_param}"
850
851 if [ "${cmd}" = "ATETxPacketWithBf" ]; then
852 do_cmd "mt76-test phy${phy_idx} set state=tx_frames"
developer1346ce52022-12-15 21:36:14 +0800853 elif [ "${cmd}" = "ATEConTxETxBfInitProc" ]; then
developercec48ac2023-03-01 17:00:33 +0800854 local wlan_idx="1"
855 if [ ${is_eagle} == "1" ]; then
856 local wlan_idx=$((phy_idx+1))
857 fi
developer1346ce52022-12-15 21:36:14 +0800858 do_cmd "mt76-test phy${phy_idx} set aid=1"
859 do_cmd "mt76-test phy${phy_idx} set txbf_act=stop_sounding txbf_param=1"
860 do_cmd "mt76-test phy${phy_idx} set txbf_act=update_ch txbf_param=1"
861 do_cmd "mt76-test phy${phy_idx} set txbf_act=ebf_prof_update txbf_param=0,0,0"
developercec48ac2023-03-01 17:00:33 +0800862 do_cmd "mt76-test phy${phy_idx} set txbf_act=apply_tx txbf_param=${wlan_idx},1,0,0,0"
863 if [ ${is_eagle} == "1" ]; then
864 do_cmd "mt76-test phy${phy_idx} set txbf_act=txcmd txbf_param=1,1,1"
865 fi
developer1346ce52022-12-15 21:36:14 +0800866 do_cmd "mt76-test phy${phy_idx} set txbf_act=pfmu_tag_read txbf_param=0,1"
developercec48ac2023-03-01 17:00:33 +0800867 do_cmd "mt76-test phy${phy_idx} set txbf_act=sta_rec_read txbf_param=${wlan_idx}"
868 do_cmd "mt76-test phy${phy_idx} set txbf_act=trigger_sounding txbf_param=0,1,0,${wlan_idx},0,0,0"
869 do_cmd "mt76-test phy${phy_idx} set txbf_act=trigger_sounding txbf_param=2,1,ff,${wlan_idx},0,0,0"
developer1346ce52022-12-15 21:36:14 +0800870 do_cmd "mt76-test phy${phy_idx} set state=rx_frames"
871 elif [ "${cmd}" = "ATEConTxETxBfGdProc" ]; then
872 do_cmd "mt76-test phy${phy_idx} set aid=1"
873 do_cmd "mt76-test phy${phy_idx} set state=rx_frames"
874 elif [ "${cmd}" = "ATETxBfInit" ]; then
875 do_cmd "mt76-test phy${phy_idx} set aid=1"
876 elif [ "${cmd}" = "ATETxBfGdInit" ]; then
877 do_cmd "mt76-test phy${phy_idx} set aid=1"
developerf9843e22022-09-13 10:57:15 +0800878 fi
879}
880
developer887da632022-10-28 09:35:38 +0800881function convert_dfs {
882 local cmd=$1
883 local param=$2
884
885 case ${cmd} in
886 "DfsRxCtrl")
887 local offchan_ch="$(echo $param | cut -d ':' -f1)"
888 local offchan_bw="$(echo $param | cut -d ':' -f2)"
889
890 if [ "$offchan_bw" = "0" ]; then
891 offchan_bw="20"
892 elif [ "$offchan_bw" = "1" ]; then
893 offchan_bw="40"
894 elif [ "$offchan_bw" = "2" ]; then
895 offchan_bw="80"
896 fi
897
898 do_cmd "mt76-test phy${phy_idx} set state=idle"
899 do_cmd "mt76-test phy${phy_idx} set offchan_ch=${offchan_ch} offchan_bw=${offchan_bw}"
900 ;;
901 "DfsRxHist")
902 local ipi_th="$(echo $param | cut -d ':' -f 1)"
903 local ipi_period="$(echo $param | cut -d ':' -f 2)"
904 local ipi_antenna="$(echo $param | cut -d ':' -f 3)"
905
906 if [ -z $ipi_antenna ]; then
907 do_cmd "mt76-test phy${phy_idx} set ipi_threshold=${ipi_th} ipi_period=${ipi_period}"
908 else
909 do_cmd "mt76-test phy${phy_idx} set ipi_threshold=${ipi_th} ipi_period=${ipi_period} ipi_antenna_idx=${ipi_antenna}"
910 fi
911 ;;
912 *)
913 esac
914}
915
developera6267142022-01-26 20:50:22 +0800916function do_ate_work() {
917 local ate_cmd=$1
918
919 case ${ate_cmd} in
920 "ATESTART")
921 local if_str=$(ifconfig | grep mon${phy_idx})
922
923 if [ ! -z "${if_str}" -a "${if_str}" != " " ]; then
924 echo "ATE already starts."
925 else
926 do_cmd "iw phy ${interface} interface add mon${phy_idx} type monitor"
developerb4b29472023-01-06 19:07:21 +0800927
928 if [ $phy_idx -ge $SOC_start_idx ]; then
929 local end_idx=$SOC_end_idx
930 local start_idx=$SOC_start_idx
931 else
932 local end_idx=$((SOC_start_idx-1))
933 local start_idx="0"
934 fi
935
936 for phy_index in $( seq $start_idx $end_idx )
937 do
938 # "phy#-1" would not be in iw dev, therefore it will grep the line from the phy#${phy_index} to the end
939 local prev_phy_index=$((phy_index-1))
940 local if_num=$(iw dev | awk "/phy#${phy_index}/,/phy#${prev_phy_index}/" | grep -c Interface)
941 local j="1"
942 # avoid del_if_count reset to 0 when start ate on another band in dbdc case
943 local del_if_count=$(get_config "DEL_IF${phy_index}_NUM" ${interface_file})
944 if [ -z "${del_if_count}" ]; then
945 local del_if_count="0"
946 fi
947
948 for if_count in $( seq 1 $if_num )
949 do
950 local del_if=$(iw dev | awk "/phy#${phy_index}/,/phy#${prev_phy_index}/" | grep Interface | sed -n ${j}p | cut -d " " -f 2)
951 if [ ! -z "${del_if}" ] && [[ "$del_if" != *"mon"* ]]; then
952 do_cmd "iw dev ${del_if} del"
953 del_if_count=$((del_if_count+1))
954 # handle the case of multiple interface in a phy
955 record_config "DEL_IF${phy_index}-${del_if_count}" ${del_if} ${interface_file}
956 else
957 # j add 1 to skip mon interface
958 j=$((j+1))
959 fi
960 done
961 record_config "DEL_IF${phy_index}_NUM" ${del_if_count} ${interface_file}
962 done
963
developera6267142022-01-26 20:50:22 +0800964 do_cmd "ifconfig mon${phy_idx} up"
developer9b7cdad2022-03-10 14:24:55 +0800965 do_cmd "iw reg set VV"
developera6267142022-01-26 20:50:22 +0800966 fi
967 ;;
968 "ATESTOP")
969 local if_str=$(ifconfig | grep mon${phy_idx})
970
971 if [ -z "${if_str}" -a "${if_str}" != " " ]; then
972 echo "ATE does not start."
973 else
974 do_cmd "mt76-test ${interface} set state=off"
975 do_cmd "iw dev mon${phy_idx} del"
developerb4b29472023-01-06 19:07:21 +0800976
977 if [ $phy_idx -ge $SOC_start_idx ]; then
978 local end_idx=$SOC_end_idx
979 local start_idx=$SOC_start_idx
980 else
981 local end_idx=$((SOC_start_idx-1))
982 local start_idx="0"
983 fi
984
985 # first check its phy and dbdc band phy has monitor interface or not
986 # if has at lease one mon interface, then skip adding back normal interface
987 local has_mon="0"
988 for phy_index in $( seq $start_idx $end_idx )
989 do
990 # "phy#-1" would not be in iw dev, therefore it will grep the line from the phy#${phy_index} to the end
991 local prev_phy_index=$((phy_index-1))
992 local has_mon_phy=$(iw dev | awk "/phy#${phy_index}/,/phy#${prev_phy_index}/" | grep "Interface mon")
993 # if this phy interface has mon interface
994 if [ ! -z "${has_mon_phy}" ]; then
995 local has_mon="1"
996 fi
997 done
998
999 for phy_index in $( seq $start_idx $end_idx )
1000 do
1001 # "phy#-1" would not be in iw dev, therefore it will grep the line from the phy#${phy_index} to the end
1002 local prev_phy_index=$((phy_index-1))
1003 local j="1"
1004 local add_if_num=$(get_config "DEL_IF${phy_index}_NUM" ${interface_file})
1005 if [ -z "${add_if_num}" ]; then
1006 local add_if_num="0"
1007 fi
1008 # if this phy interface (including its dbdc phy) has no mon interface and can find deleted interface in file, then add it back
1009 if [ "${has_mon}" == "0" ] && [ $add_if_num -ge "1" ]; then
1010 local if_index=$add_if_num
1011 # add interface backwards
1012 while [ $if_index -gt "0" ]
1013 do
1014 local add_if=$(get_config "DEL_IF${phy_index}-${if_index}" ${interface_file})
1015 do_cmd "iw phy phy${phy_index} interface add ${add_if} type managed"
1016 # remove the deleted interface in interface_file since it is added back
1017 sed -i "/DEL_IF${phy_index}-${if_index}=/d" ${interface_file}
1018 if_index=$((if_index-1))
1019 done
1020 # remove the number of deleted interface in interface_file since it is all added back
1021 sed -i "/DEL_IF${phy_index}_NUM=/d" ${interface_file}
1022 fi
1023 done
1024
developer461cb542022-04-29 18:17:44 +08001025 do_cmd "mt76-test ${interface} set aid=0"
developera6267142022-01-26 20:50:22 +08001026 fi
developer10946c32022-03-04 18:28:43 +08001027
developerf90c9af2022-12-28 22:40:23 +08001028 if [ ${phy_idx} -lt ${SOC_start_idx} ]; then
developer679a6aa2022-09-07 09:52:41 +08001029 sed -i '/_PCIE=/d' ${iwpriv_file}
developerf90c9af2022-12-28 22:40:23 +08001030 elif [ ${phy_idx} -ge ${SOC_start_idx} ]; then
1031 sed -i '/_SOC=/d' ${iwpriv_file}
developer679a6aa2022-09-07 09:52:41 +08001032 fi
developera6267142022-01-26 20:50:22 +08001033 ;;
developer461cb542022-04-29 18:17:44 +08001034 "TXCOMMIT")
1035 do_cmd "mt76-test ${interface} set aid=1"
1036 ;;
developera6267142022-01-26 20:50:22 +08001037 "TXFRAME")
1038 do_cmd "mt76-test ${interface} set state=tx_frames"
1039 ;;
developer9b7cdad2022-03-10 14:24:55 +08001040 "TXSTOP"|"RXSTOP")
developera6267142022-01-26 20:50:22 +08001041 do_cmd "mt76-test ${interface} set state=idle"
1042 ;;
developer461cb542022-04-29 18:17:44 +08001043 "TXREVERT")
1044 do_cmd "mt76-test ${interface} set aid=0"
1045 ;;
developera6267142022-01-26 20:50:22 +08001046 "RXFRAME")
1047 do_cmd "mt76-test ${interface} set state=rx_frames"
1048 ;;
1049 "TXCONT")
1050 do_cmd "mt76-test ${interface} set state=tx_cont"
1051 ;;
developer071927d2022-08-31 20:39:29 +08001052 "GROUPREK")
1053 do_cmd "mt76-test ${interface} set state=group_prek"
1054 do_cmd "atenl -i ${interface} -c \"eeprom precal sync group\""
1055 ;;
1056 "GROUPREKDump")
1057 do_cmd "mt76-test ${interface} set state=group_prek_dump"
1058 ;;
1059 "GROUPREKClean")
1060 do_cmd "mt76-test ${interface} set state=group_prek_clean"
1061 do_cmd "atenl -i ${interface} -c \"eeprom precal group clean\""
1062 ;;
1063 "DPD2G")
1064 do_cmd "mt76-test ${interface} set state=dpd_2g"
1065 do_cmd "atenl -i ${interface} -c \"eeprom precal sync dpd 2g\""
1066 ;;
1067 "DPD5G")
1068 do_cmd "mt76-test ${interface} set state=dpd_5g"
1069 do_cmd "atenl -i ${interface} -c \"eeprom precal sync dpd 5g\""
1070 ;;
1071 "DPD6G")
1072 do_cmd "mt76-test ${interface} set state=dpd_6g"
1073 do_cmd "atenl -i ${interface} -c \"eeprom precal sync dpd 6g\""
1074 ;;
1075 "DPDDump")
1076 do_cmd "mt76-test ${interface} set state=dpd_dump"
1077 ;;
1078 "DPDClean")
1079 do_cmd "mt76-test ${interface} set state=dpd_clean"
1080 do_cmd "atenl -i ${interface} -c \"eeprom precal dpd clean\""
1081 ;;
developer9b7cdad2022-03-10 14:24:55 +08001082 *)
developer9b7cdad2022-03-10 14:24:55 +08001083 print_debug "skip ${ate_cmd}"
developera6267142022-01-26 20:50:22 +08001084 ;;
1085 esac
1086}
1087
developerf90c9af2022-12-28 22:40:23 +08001088function dump_usage {
1089 echo "Usage:"
1090 echo " mwctl <interface> set csi ctrl=<opt1>,<opt2>,<opt3>,<opt4> (macaddr=<macaddr>)"
1091 echo " mwctl <interface> set csi interval=<interval (us)>"
1092 echo " mwctl <interface> dump csi <packet num> <filename>"
1093 echo " mwctl <interface> set amnt <index>(0x0~0xf) <mac addr>(xx:xx:xx:xx:xx:xx)"
1094 echo " mwctl <interface> dump amnt <index> (0x0~0xf or 0xff)"
1095 echo " mwctl <interface> set ap_rfeatures he_gi=<val>"
1096 echo " mwctl <interface> set ap_rfeatures he_ltf=<val>"
1097 echo " mwctl <interface> set ap_rfeatures trig_type=<enable>,<val> (val: 0-7)"
1098 echo " mwctl <interface> set ap_rfeatures ack_policy=<val> (val: 0-4)"
1099 echo " mwctl <interface> set ap_wireless fixed_mcs=<val>"
1100 echo " mwctl <interface> set ap_wireless ofdma=<val> (0: disable, 1: DL, 2: UL)"
1101 echo " mwctl <interface> set ap_wireless nusers_ofdma=<val>"
1102 echo " mwctl <interface> set ap_wireless ppdu_type=<val> (0: SU, 1: MU, 4: LEGACY)"
1103 echo " mwctl <interface> set ap_wireless add_ba_req_bufsize=<val>"
1104 echo " mwctl <interface> set ap_wireless mimo=<val> (0: DL, 1: UL)"
1105 echo " mwctl <interface> set ap_wireless ampdu=<enable>"
1106 echo " mwctl <interface> set ap_wireless amsdu=<enable>"
1107 echo " mwctl <interface> set ap_wireless cert=<enable>"
developer57de9b72023-02-20 11:15:54 +08001108 echo " mwctl <interface> set mu onoff=<val> (bitmap- UL MU-MIMO(bit3), DL MU-MIMO(bit2), UL OFDMA(bit1), DL OFDMA(bit0))"
developerf90c9af2022-12-28 22:40:23 +08001109 echo " mwctl <interface> dump phy_capa"
1110}
1111
developere3d5e5e2023-01-16 16:58:29 +08001112function register_handler {
1113
1114 local phy_idx=$1
1115 local offset=$2
1116 local val=$3
1117 local cmd=$4
1118 local w_cmd="write"
1119
1120 regidx=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/regidx
1121 regval=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/regval
1122
1123 echo ${offset} > ${regidx}
1124 if [[ "${cmd}" == "${w_cmd}" ]]; then
1125 echo ${val} > ${regval}
1126 fi
1127
1128 res=$(cat ${regval} | cut -d 'x' -f 2)
1129 printf "%s mac:[%s]:%s\n" ${interface_ori} ${offset} ${res}
1130}
1131
developer10946c32022-03-04 18:28:43 +08001132# main start here
developerb4b29472023-01-06 19:07:21 +08001133parse_sku
developerf90c9af2022-12-28 22:40:23 +08001134if [ -z ${interface} ]; then
1135 dump_usage
1136 exit
1137elif [[ ${interface} == "ra"* ]]; then
developereebce5c2022-08-26 19:05:56 +08001138 convert_interface $interface
developercec48ac2023-03-01 17:00:33 +08001139elif [[ ${interface} == "phy" ]]; then
1140 # handle mwctl phy phy0 e2p ... case
1141 interface=$2
1142 cmd_type=$3
1143 full_cmd=$4
developer10946c32022-03-04 18:28:43 +08001144fi
1145
developer679a6aa2022-09-07 09:52:41 +08001146tmp_work_mode=$(get_config "WORKMODE" ${iwpriv_file})
1147
1148if [ ! -z ${tmp_work_mode} ]; then
1149 work_mode=${tmp_work_mode}
1150fi
1151
developer10946c32022-03-04 18:28:43 +08001152cmd=$(echo ${full_cmd} | sed s/=/' '/g | cut -d " " -f 1)
1153param=$(echo ${full_cmd} | sed s/=/' '/g | cut -d " " -f 2)
1154
developer3abe1ad2022-01-24 11:13:32 +08001155if [ "${cmd_type}" = "set" ]; then
1156 skip=0
developer3abe1ad2022-01-24 11:13:32 +08001157 case ${cmd} in
developerf90c9af2022-12-28 22:40:23 +08001158 ## In wifi 7 chipset, testmode & vendor command both use mwctl
1159 ## Therefore this wrapper would translate it to either mt76-test or mt76-vendor based on the attribute of the command
1160 ## Translate to mt76-vendor command
developer57de9b72023-02-20 11:15:54 +08001161 "csi"|"amnt"|"ap_rfeatures"|"ap_wireless"|"mu")
developercec48ac2023-03-01 17:00:33 +08001162 if [ ${is_eagle} == "1" ]; then
developer249ac1b2023-02-09 09:54:38 +08001163 do_cmd "hostapd_cli -i $*"
developercec48ac2023-03-01 17:00:33 +08001164 else
developer249ac1b2023-02-09 09:54:38 +08001165 do_cmd "mt76-vendor $*"
developercec48ac2023-03-01 17:00:33 +08001166 fi
1167 skip=1
developerf90c9af2022-12-28 22:40:23 +08001168 ;;
developer3abe1ad2022-01-24 11:13:32 +08001169 "ATE")
1170 do_ate_work ${param}
1171
1172 skip=1
1173 ;;
1174 "ATETXCNT"|"ATETXLEN"|"ATETXMCS"|"ATEVHTNSS"|"ATETXLDPC"|"ATETXSTBC"| \
1175 "ATEPKTTXTIME"|"ATEIPG"|"ATEDUTYCYCLE"|"ATETXFREQOFFSET")
1176 cmd_new=$(simple_convert ${cmd})
developer679a6aa2022-09-07 09:52:41 +08001177 if [ "${param_new}" = "undefined" ]; then
1178 echo "unknown cmd: ${cmd}"
1179 exit
1180 fi
developer3abe1ad2022-01-24 11:13:32 +08001181 param_new=${param}
developer1346ce52022-12-15 21:36:14 +08001182 if [ "${cmd}" = "ATETXCNT" ] && [ "${param}" = "0" ]; then
1183 param_new="10000000"
1184 fi
developer3abe1ad2022-01-24 11:13:32 +08001185 ;;
1186 "ATETXANT"|"ATERXANT")
1187 cmd_new="tx_antenna"
1188 param_new=${param}
1189 ;;
1190 "ATETXGI")
developercec48ac2023-03-01 17:00:33 +08001191 if [ ${is_eagle} == "0" ]; then
1192 tx_mode=$(convert_tx_mode $(get_config "ATETXMODE" ${iwpriv_file}))
1193 convert_gi ${tx_mode} ${param}
1194 skip=1
1195 else
1196 cmd_new="tx_rate_sgi"
1197 param_new=${param}
1198 fi
developer3abe1ad2022-01-24 11:13:32 +08001199 ;;
1200 "ATETXMODE")
1201 cmd_new="tx_rate_mode"
1202 param_new=$(convert_tx_mode ${param})
developer679a6aa2022-09-07 09:52:41 +08001203 if [ "${param_new}" = "undefined" ]; then
1204 echo "unknown tx mode"
1205 echo "0:cck, 1:ofdm, 2:ht, 4:vht, 8:he_su, 9:he_er, 10:he_tb, 11:he_mu"
1206 exit
1207 else
1208 record_config ${cmd} ${param} ${iwpriv_file}
1209 fi
developer3abe1ad2022-01-24 11:13:32 +08001210 ;;
developercec48ac2023-03-01 17:00:33 +08001211 "ATETXPOW0"|"ATETXPOW1"|"ATETXPOW2"|"ATETXPOW3"|"ATETXPOW")
developer3abe1ad2022-01-24 11:13:32 +08001212 cmd_new="tx_power"
developercec48ac2023-03-01 17:00:33 +08001213 if [ "${param}" == "127" ]; then
1214 # for iTest verification
1215 exit
1216 fi
developer3abe1ad2022-01-24 11:13:32 +08001217 param_new="${param},0,0,0"
1218 ;;
developercec48ac2023-03-01 17:00:33 +08001219 "ATEMUAID")
1220 cmd_new="aid"
1221 param_new=${param}
1222 ;;
developer3abe1ad2022-01-24 11:13:32 +08001223 "ATETXBW")
developer679a6aa2022-09-07 09:52:41 +08001224 record_config ${cmd} ${param} ${iwpriv_file}
developer3abe1ad2022-01-24 11:13:32 +08001225 skip=1
1226 ;;
1227 "ATECHANNEL")
1228 convert_channel ${param}
1229 skip=1
1230 ;;
developer10946c32022-03-04 18:28:43 +08001231 "ATERXSTAT")
1232 convert_rxstat
1233 skip=1
1234 ;;
developer3abe1ad2022-01-24 11:13:32 +08001235 "ATECTRLBANDIDX")
developer10946c32022-03-04 18:28:43 +08001236 change_band_idx ${param}
developer3abe1ad2022-01-24 11:13:32 +08001237 skip=1
1238 ;;
developer10946c32022-03-04 18:28:43 +08001239 "ATEDA"|"ATESA"|"ATEBSSID")
1240 set_mac_addr ${cmd} ${param}
1241 skip=1
1242 ;;
developer887da632022-10-28 09:35:38 +08001243 "DfsRxCtrl"|"DfsRxHist")
1244 convert_dfs ${cmd} ${param}
1245 skip=1
1246 ;;
developer1346ce52022-12-15 21:36:14 +08001247 "ATETxBfInit"|"ATETxBfGdInit"|"ATEIBFPhaseComp"|"ATEEBfProfileConfig"|"ATEIBfProfileConfig"| \
1248 "TxBfTxApply"|"ATETxPacketWithBf"|"TxBfProfileData20MAllWrite"|"ATEIBfInstCal"| \
1249 "ATEIBfGdCal"|"ATEIBFPhaseE2pUpdate"|"TriggerSounding"|"StopSounding"| \
1250 "StaRecBfRead"|"TxBfProfileTagInValid"|"TxBfProfileTagWrite"|"TxBfProfileTagRead"| \
1251 "ATEIBFPhaseVerify"|"ATEConTxETxBfGdProc"|"ATEConTxETxBfInitProc")
developerf9843e22022-09-13 10:57:15 +08001252 convert_ibf ${cmd} ${param}
1253 skip=1
1254 ;;
developer3abe1ad2022-01-24 11:13:32 +08001255 "bufferMode")
1256 if [ "${param}" = "2" ]; then
developer461cb542022-04-29 18:17:44 +08001257 do_cmd "atenl -i ${interface} -c \"eeprom update buffermode\""
developer3abe1ad2022-01-24 11:13:32 +08001258 fi
1259 skip=1
1260 ;;
developera6267142022-01-26 20:50:22 +08001261 "ResetCounter"|"ATERXSTATRESET")
1262 skip=1
1263 ;;
developer679a6aa2022-09-07 09:52:41 +08001264 "WORKMODE")
1265 record_config "WORKMODE" ${param} ${iwpriv_file}
1266 echo "Entering ${param} mode in iwpriv"
1267 skip=1
1268 ;;
developer3abe1ad2022-01-24 11:13:32 +08001269 *)
developer9b7cdad2022-03-10 14:24:55 +08001270 print_debug "Unknown command to set: ${cmd}"
developer3abe1ad2022-01-24 11:13:32 +08001271 skip=1
1272 esac
1273
1274 if [ "${skip}" != "1" ]; then
1275 do_cmd "mt76-test ${interface} set ${cmd_new}=${param_new}"
1276 fi
developer10946c32022-03-04 18:28:43 +08001277
developer3abe1ad2022-01-24 11:13:32 +08001278elif [ "${cmd_type}" = "show" ]; then
developer1346ce52022-12-15 21:36:14 +08001279 if [ "${cmd}" = "wtbl" ]; then
1280 wlan_idx=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/wlan_idx
1281 wtbl_info=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/wtbl_info
1282
1283 do_cmd "echo ${param} > ${wlan_idx}"
1284 do_cmd "cat ${wtbl_info}"
developercec48ac2023-03-01 17:00:33 +08001285 elif [ "${cmd}" = "ATERXSTAT" ]; then
1286 convert_rxstat
developer1346ce52022-12-15 21:36:14 +08001287 else
1288 do_cmd "mt76-test ${interface} dump"
1289 do_cmd "mt76-test ${interface} dump stats"
1290 fi
developer10946c32022-03-04 18:28:43 +08001291
developer3abe1ad2022-01-24 11:13:32 +08001292elif [ "${cmd_type}" = "e2p" ]; then
developerf90c9af2022-12-28 22:40:23 +08001293 # support multiple read write
developera6267142022-01-26 20:50:22 +08001294 # eeprom offset write
1295 if [[ ${full_cmd} == *"="* ]]; then
developerf90c9af2022-12-28 22:40:23 +08001296 IFS=,
1297 for tuple in $full_cmd
1298 do
1299 cmd=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 1)
1300 param=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 2)
1301 offset=$(printf "0x%s" ${cmd})
1302 val=$(printf "0x%s" ${param})
1303 tmp=$((${val} & 0xff))
1304 tmp=$(printf "0x%x" ${tmp})
1305 do_cmd "atenl -i ${interface} -c \"eeprom set ${offset}=${tmp}\""
developera6267142022-01-26 20:50:22 +08001306
developerf90c9af2022-12-28 22:40:23 +08001307 offset=$((${offset}))
1308 offset=$(expr ${offset} + "1")
1309 offset=$(printf "0x%x" ${offset})
1310 tmp=$(((${val} >> 8) & 0xff))
1311 tmp=$(printf "0x%x" ${tmp})
1312 do_cmd "atenl -i ${interface} -c \"eeprom set ${offset}=${tmp}\""
1313 done
developera6267142022-01-26 20:50:22 +08001314 else
developerf90c9af2022-12-28 22:40:23 +08001315 IFS=,
1316 for tuple in $full_cmd
1317 do
1318 cmd=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 1)
1319 param=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 2)
1320 offset=$(printf "0x%s" ${cmd})
1321 val=$(printf "0x%s" ${param})
1322 v1=$(do_cmd "atenl -i ${interface} -c \"eeprom read ${param}\"")
1323 v1=$(echo "${v1}" | grep "val =" | cut -d '(' -f 2 | grep -o -E '[0-9]+')
developer3abe1ad2022-01-24 11:13:32 +08001324
developerf90c9af2022-12-28 22:40:23 +08001325 tmp=$(printf "0x%s" ${param})
1326 tmp=$((${tmp}))
1327 param2=$(expr ${tmp} + "1")
1328 param2=$(printf "%x" ${param2})
1329 v2=$(do_cmd "atenl -i ${interface} -c \"eeprom read ${param2}\"")
1330 v2=$(echo "${v2}" | grep "val =" | cut -d '(' -f 2 | grep -o -E '[0-9]+')
developera6267142022-01-26 20:50:22 +08001331
developerf90c9af2022-12-28 22:40:23 +08001332 param=$(printf "0x%s" ${param})
1333 param=$(printf "%04x" ${param})
1334 param=$(echo $param | tr 'a-z' 'A-Z')
1335 printf "%s e2p:\n" ${interface_ori}
1336 printf "[0x%s]:0x%02x%02x\n" ${param} ${v2} ${v1}
1337 done
developera6267142022-01-26 20:50:22 +08001338 fi
developer10946c32022-03-04 18:28:43 +08001339
developera6267142022-01-26 20:50:22 +08001340elif [ "${cmd_type}" = "mac" ]; then
developera6267142022-01-26 20:50:22 +08001341 offset=$(printf "0x%s" ${cmd})
1342 val=$(printf "0x%s" ${param})
1343
developera6267142022-01-26 20:50:22 +08001344 # reg write
1345 if [[ ${full_cmd} == *"="* ]]; then
developere3d5e5e2023-01-16 16:58:29 +08001346 register_handler ${phy_idx} ${offset} ${val} "write"
1347 else
1348 start_addr=$(echo ${full_cmd} | sed s/-/' '/g | cut -d " " -f 1)
1349 end_addr=$(echo ${full_cmd} | sed s/-/' '/g | cut -d " " -f 2)
1350 loop=$((0x${end_addr}-0x${start_addr}))
developer10946c32022-03-04 18:28:43 +08001351
developere3d5e5e2023-01-16 16:58:29 +08001352 if [[ ${loop} == "0" ]]; then
1353 register_handler ${phy_idx} ${offset} ${val}
1354 else
1355 i=0
1356 while [ $i -le $loop ]; do
1357 addr=$((0x${start_addr}+$i))
1358 offset=$(printf "0x%x" ${addr})
1359 register_handler ${phy_idx} ${offset} ${val}
1360 i=$(($i + 4))
1361 done
1362 fi
1363 fi
developer461cb542022-04-29 18:17:44 +08001364
developerf90c9af2022-12-28 22:40:23 +08001365## dump command is only for vendor commands
1366elif [ "${cmd_type}" = "dump" ]; then
1367 do_cmd "mt76-vendor $*"
developer3abe1ad2022-01-24 11:13:32 +08001368else
1369 echo "Unknown command"
1370fi