| // SPDX-License-Identifier: GPL-2.0+ |
| #include <linux/bitfield.h> |
| #include <linux/firmware.h> |
| #include <linux/module.h> |
| #include <linux/nvmem-consumer.h> |
| #include <linux/of_address.h> |
| #include <linux/of_platform.h> |
| #include <linux/pinctrl/consumer.h> |
| #include <linux/phy.h> |
| |
| #define MEDAITEK_2P5GE_PHY_DMB_FW "mediatek-2p5ge-phy-dmb.bin" |
| #define MEDIATEK_2P5GE_PHY_PMB_FW "mediatek-2p5ge-phy-pmb.bin" |
| |
| #define MD32_EN_CFG 0x18 |
| #define MD32_EN BIT(0) |
| |
| #define BASE100T_STATUS_EXTEND (0x10) |
| #define BASE1000T_STATUS_EXTEND (0x11) |
| #define EXTEND_CTRL_AND_STATUS (0x16) |
| |
| #define PHY_AUX_CTRL_STATUS (0x1d) |
| #define PHY_AUX_DPX_MASK GENMASK(5, 5) |
| #define PHY_AUX_SPEED_MASK GENMASK(4, 2) |
| |
| /* Registers on MDIO_MMD_VEND1 */ |
| #define MTK_PHY_LINK_STATUS_MISC (0xa2) |
| #define MTK_PHY_FDX_ENABLE BIT(5) |
| |
| /* Registers on MDIO_MMD_VEND2 */ |
| #define MTK_PHY_LED0_ON_CTRL (0x24) |
| #define MTK_PHY_LED0_ON_LINK1000 BIT(0) |
| #define MTK_PHY_LED0_ON_LINK100 BIT(1) |
| #define MTK_PHY_LED0_ON_LINK10 BIT(2) |
| #define MTK_PHY_LED0_ON_LINK2500 BIT(7) |
| #define MTK_PHY_LED0_POLARITY BIT(14) |
| |
| #define MTK_PHY_LED1_ON_CTRL (0x26) |
| #define MTK_PHY_LED1_ON_FDX BIT(4) |
| #define MTK_PHY_LED1_ON_HDX BIT(5) |
| #define MTK_PHY_LED1_POLARITY BIT(14) |
| |
| enum { |
| PHY_AUX_SPD_10 = 0, |
| PHY_AUX_SPD_100, |
| PHY_AUX_SPD_1000, |
| PHY_AUX_SPD_2500, |
| }; |
| |
| static int mt798x_2p5ge_phy_config_init(struct phy_device *phydev) |
| { |
| int ret; |
| int i; |
| const struct firmware *fw; |
| struct device *dev = &phydev->mdio.dev; |
| struct device_node *np; |
| void __iomem *dmb_addr; |
| void __iomem *pmb_addr; |
| void __iomem *mcucsr_base; |
| u16 reg; |
| struct pinctrl *pinctrl; |
| |
| |
| np = of_find_compatible_node(NULL, NULL, "mediatek,2p5gphy-fw"); |
| if (!np) |
| return -ENOENT; |
| |
| dmb_addr = of_iomap(np, 0); |
| if (!dmb_addr) |
| return -ENOMEM; |
| pmb_addr = of_iomap(np, 1); |
| if (!pmb_addr) |
| return -ENOMEM; |
| mcucsr_base = of_iomap(np, 2); |
| if (!mcucsr_base) |
| return -ENOMEM; |
| |
| ret = request_firmware(&fw, MEDAITEK_2P5GE_PHY_DMB_FW, dev); |
| if (ret) { |
| dev_err(dev, "failed to load firmware: %s, ret: %d\n", |
| MEDAITEK_2P5GE_PHY_DMB_FW, ret); |
| return ret; |
| } |
| for (i = 0; i < fw->size - 1; i += 4) |
| writel(*((uint32_t *)(fw->data + i)), dmb_addr + i); |
| release_firmware(fw); |
| |
| ret = request_firmware(&fw, MEDIATEK_2P5GE_PHY_PMB_FW, dev); |
| if (ret) { |
| dev_err(dev, "failed to load firmware: %s, ret: %d\n", |
| MEDIATEK_2P5GE_PHY_PMB_FW, ret); |
| return ret; |
| } |
| for (i = 0; i < fw->size - 1; i += 4) |
| writel(*((uint32_t *)(fw->data + i)), pmb_addr + i); |
| release_firmware(fw); |
| |
| reg = readw(mcucsr_base + MD32_EN_CFG); |
| writew(reg | MD32_EN, mcucsr_base + MD32_EN_CFG); |
| dev_info(dev, "Firmware loading/trigger ok.\n"); |
| |
| /* Setup LED */ |
| phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_ON_CTRL, |
| MTK_PHY_LED0_POLARITY | MTK_PHY_LED0_ON_LINK10 | |
| MTK_PHY_LED0_ON_LINK100 | MTK_PHY_LED0_ON_LINK1000 | |
| MTK_PHY_LED0_ON_LINK2500); |
| phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED1_ON_CTRL, |
| MTK_PHY_LED1_ON_FDX | MTK_PHY_LED1_ON_HDX); |
| |
| pinctrl = devm_pinctrl_get_select(&phydev->mdio.dev, "i2p5gbe-led"); |
| if (IS_ERR(pinctrl)) { |
| dev_err(&phydev->mdio.dev, "Fail to set LED pins!\n"); |
| return PTR_ERR(pinctrl); |
| } |
| |
| return 0; |
| } |
| |
| static int mt798x_2p5ge_phy_config_aneg(struct phy_device *phydev) |
| { |
| bool changed = false; |
| u32 adv; |
| int ret; |
| |
| if (phydev->autoneg == AUTONEG_DISABLE) { |
| /* Configure half duplex with genphy_setup_forced, |
| * because genphy_c45_pma_setup_forced does not support. |
| */ |
| return phydev->duplex != DUPLEX_FULL |
| ? genphy_setup_forced(phydev) |
| : genphy_c45_pma_setup_forced(phydev); |
| } |
| |
| ret = genphy_c45_an_config_aneg(phydev); |
| if (ret < 0) |
| return ret; |
| if (ret > 0) |
| changed = true; |
| |
| adv = linkmode_adv_to_mii_ctrl1000_t(phydev->advertising); |
| ret = phy_modify_changed(phydev, MII_CTRL1000, |
| ADVERTISE_1000FULL | ADVERTISE_1000HALF, |
| adv); |
| if (ret < 0) |
| return ret; |
| if (ret > 0) |
| changed = true; |
| |
| return genphy_c45_check_and_restart_aneg(phydev, changed); |
| } |
| |
| static int mt798x_2p5ge_phy_get_features(struct phy_device *phydev) |
| { |
| int ret; |
| |
| ret = genphy_read_abilities(phydev); |
| if (ret) |
| return ret; |
| |
| /* We don't support HDX at MAC layer on mt798x. |
| * So mask phy's HDX capabilities, too. |
| */ |
| linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, |
| phydev->supported); |
| linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, |
| phydev->supported); |
| linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, |
| phydev->supported); |
| linkmode_set_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, |
| phydev->supported); |
| linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported); |
| |
| return 0; |
| } |
| |
| static int mt798x_2p5ge_phy_read_status(struct phy_device *phydev) |
| { |
| int ret; |
| |
| ret = genphy_update_link(phydev); |
| if (ret) |
| return ret; |
| |
| phydev->speed = SPEED_UNKNOWN; |
| phydev->duplex = DUPLEX_UNKNOWN; |
| phydev->pause = 0; |
| phydev->asym_pause = 0; |
| |
| if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) { |
| ret = genphy_c45_read_lpa(phydev); |
| if (ret < 0) |
| return ret; |
| |
| /* Read the link partner's 1G advertisement */ |
| ret = phy_read(phydev, MII_STAT1000); |
| if (ret < 0) |
| return ret; |
| mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, ret); |
| } else if (phydev->autoneg == AUTONEG_DISABLE) { |
| linkmode_zero(phydev->lp_advertising); |
| } |
| |
| ret = phy_read(phydev, PHY_AUX_CTRL_STATUS); |
| if (ret < 0) |
| return ret; |
| |
| switch (FIELD_GET(PHY_AUX_SPEED_MASK, ret)) { |
| case PHY_AUX_SPD_10: |
| phydev->speed = SPEED_10; |
| break; |
| case PHY_AUX_SPD_100: |
| phydev->speed = SPEED_100; |
| break; |
| case PHY_AUX_SPD_1000: |
| phydev->speed = SPEED_1000; |
| break; |
| case PHY_AUX_SPD_2500: |
| phydev->speed = SPEED_2500; |
| break; |
| } |
| |
| ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LINK_STATUS_MISC); |
| if (ret < 0) |
| return ret; |
| phydev->duplex = (ret & MTK_PHY_FDX_ENABLE) ? DUPLEX_FULL : DUPLEX_HALF; |
| |
| return 0; |
| } |
| |
| static struct phy_driver mtk_gephy_driver[] = { |
| { |
| PHY_ID_MATCH_EXACT(0x00339c11), |
| .name = "MediaTek MT798x 2.5GbE PHY", |
| .config_init = mt798x_2p5ge_phy_config_init, |
| .config_aneg = mt798x_2p5ge_phy_config_aneg, |
| .get_features = mt798x_2p5ge_phy_get_features, |
| .read_status = mt798x_2p5ge_phy_read_status, |
| //.config_intr = genphy_no_config_intr, |
| //.handle_interrupt = genphy_no_ack_interrupt, |
| //.suspend = genphy_suspend, |
| //.resume = genphy_resume, |
| }, |
| }; |
| |
| module_phy_driver(mtk_gephy_driver); |
| |
| static struct mdio_device_id __maybe_unused mtk_2p5ge_phy_tbl[] = { |
| { PHY_ID_MATCH_VENDOR(0x00339c00) }, |
| { } |
| }; |
| |
| MODULE_DESCRIPTION("MediaTek 2.5Gb Ethernet PHY driver"); |
| MODULE_AUTHOR("SkyLake Huang <SkyLake.Huang@mediatek.com>"); |
| MODULE_LICENSE("GPL"); |
| |
| MODULE_DEVICE_TABLE(mdio, mtk_2p5ge_phy_tbl); |