board/ti/am335x/board.c

// SPDX-License-Identifier: GPL-2.0+
/*
 * board.c
 *
 * Board functions for TI AM335X based boards
 *
 * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
 */

#include <common.h>
#include <dm.h>
#include <env.h>
#include <errno.h>
#include <spl.h>
#include <serial.h>
#include <asm/arch/cpu.h>
#include <asm/arch/hardware.h>
#include <asm/arch/omap.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/clock.h>
#include <asm/arch/clk_synthesizer.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/mem.h>
#include <asm/io.h>
#include <asm/emif.h>
#include <asm/gpio.h>
#include <asm/omap_common.h>
#include <asm/omap_sec_common.h>
#include <asm/omap_mmc.h>
#include <i2c.h>
#include <miiphy.h>
#include <cpsw.h>
#include <power/tps65217.h>
#include <power/tps65910.h>
#include <env_internal.h>
#include <watchdog.h>
#include "../common/board_detect.h"
#include "board.h"

DECLARE_GLOBAL_DATA_PTR;

/* GPIO that controls power to DDR on EVM-SK */
#define GPIO_TO_PIN(bank, gpio)		(32 * (bank) + (gpio))
#define GPIO_DDR_VTT_EN		GPIO_TO_PIN(0, 7)
#define ICE_GPIO_DDR_VTT_EN	GPIO_TO_PIN(0, 18)
#define GPIO_PR1_MII_CTRL	GPIO_TO_PIN(3, 4)
#define GPIO_MUX_MII_CTRL	GPIO_TO_PIN(3, 10)
#define GPIO_FET_SWITCH_CTRL	GPIO_TO_PIN(0, 7)
#define GPIO_PHY_RESET		GPIO_TO_PIN(2, 5)
#define GPIO_ETH0_MODE		GPIO_TO_PIN(0, 11)
#define GPIO_ETH1_MODE		GPIO_TO_PIN(1, 26)

static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;

#define GPIO0_RISINGDETECT	(AM33XX_GPIO0_BASE + OMAP_GPIO_RISINGDETECT)
#define GPIO1_RISINGDETECT	(AM33XX_GPIO1_BASE + OMAP_GPIO_RISINGDETECT)

#define GPIO0_IRQSTATUS1	(AM33XX_GPIO0_BASE + OMAP_GPIO_IRQSTATUS1)
#define GPIO1_IRQSTATUS1	(AM33XX_GPIO1_BASE + OMAP_GPIO_IRQSTATUS1)

#define GPIO0_IRQSTATUSRAW	(AM33XX_GPIO0_BASE + 0x024)
#define GPIO1_IRQSTATUSRAW	(AM33XX_GPIO1_BASE + 0x024)

/*
 * Read header information from EEPROM into global structure.
 */
#ifdef CONFIG_TI_I2C_BOARD_DETECT
void do_board_detect(void)
{
	enable_i2c0_pin_mux();
#ifndef CONFIG_DM_I2C
	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
#endif
	if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
				 CONFIG_EEPROM_CHIP_ADDRESS))
		printf("ti_i2c_eeprom_init failed\n");
}
#endif

#ifndef CONFIG_DM_SERIAL
struct serial_device *default_serial_console(void)
{
	if (board_is_icev2())
		return &eserial4_device;
	else
		return &eserial1_device;
}
#endif

#ifndef CONFIG_SKIP_LOWLEVEL_INIT
static const struct ddr_data ddr2_data = {
	.datardsratio0 = MT47H128M16RT25E_RD_DQS,
	.datafwsratio0 = MT47H128M16RT25E_PHY_FIFO_WE,
	.datawrsratio0 = MT47H128M16RT25E_PHY_WR_DATA,
};

static const struct cmd_control ddr2_cmd_ctrl_data = {
	.cmd0csratio = MT47H128M16RT25E_RATIO,

	.cmd1csratio = MT47H128M16RT25E_RATIO,

	.cmd2csratio = MT47H128M16RT25E_RATIO,
};

static const struct emif_regs ddr2_emif_reg_data = {
	.sdram_config = MT47H128M16RT25E_EMIF_SDCFG,
	.ref_ctrl = MT47H128M16RT25E_EMIF_SDREF,
	.sdram_tim1 = MT47H128M16RT25E_EMIF_TIM1,
	.sdram_tim2 = MT47H128M16RT25E_EMIF_TIM2,
	.sdram_tim3 = MT47H128M16RT25E_EMIF_TIM3,
	.emif_ddr_phy_ctlr_1 = MT47H128M16RT25E_EMIF_READ_LATENCY,
};

static const struct emif_regs ddr2_evm_emif_reg_data = {
	.sdram_config = MT47H128M16RT25E_EMIF_SDCFG,
	.ref_ctrl = MT47H128M16RT25E_EMIF_SDREF,
	.sdram_tim1 = MT47H128M16RT25E_EMIF_TIM1,
	.sdram_tim2 = MT47H128M16RT25E_EMIF_TIM2,
	.sdram_tim3 = MT47H128M16RT25E_EMIF_TIM3,
	.ocp_config = EMIF_OCP_CONFIG_AM335X_EVM,
	.emif_ddr_phy_ctlr_1 = MT47H128M16RT25E_EMIF_READ_LATENCY,
};

static const struct ddr_data ddr3_data = {
	.datardsratio0 = MT41J128MJT125_RD_DQS,
	.datawdsratio0 = MT41J128MJT125_WR_DQS,
	.datafwsratio0 = MT41J128MJT125_PHY_FIFO_WE,
	.datawrsratio0 = MT41J128MJT125_PHY_WR_DATA,
};

static const struct ddr_data ddr3_beagleblack_data = {
	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
	.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
	.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
	.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
};

static const struct ddr_data ddr3_evm_data = {
	.datardsratio0 = MT41J512M8RH125_RD_DQS,
	.datawdsratio0 = MT41J512M8RH125_WR_DQS,
	.datafwsratio0 = MT41J512M8RH125_PHY_FIFO_WE,
	.datawrsratio0 = MT41J512M8RH125_PHY_WR_DATA,
};

static const struct ddr_data ddr3_icev2_data = {
	.datardsratio0 = MT41J128MJT125_RD_DQS_400MHz,
	.datawdsratio0 = MT41J128MJT125_WR_DQS_400MHz,
	.datafwsratio0 = MT41J128MJT125_PHY_FIFO_WE_400MHz,
	.datawrsratio0 = MT41J128MJT125_PHY_WR_DATA_400MHz,
};

static const struct cmd_control ddr3_cmd_ctrl_data = {
	.cmd0csratio = MT41J128MJT125_RATIO,
	.cmd0iclkout = MT41J128MJT125_INVERT_CLKOUT,

	.cmd1csratio = MT41J128MJT125_RATIO,
	.cmd1iclkout = MT41J128MJT125_INVERT_CLKOUT,

	.cmd2csratio = MT41J128MJT125_RATIO,
	.cmd2iclkout = MT41J128MJT125_INVERT_CLKOUT,
};

static const struct cmd_control ddr3_beagleblack_cmd_ctrl_data = {
	.cmd0csratio = MT41K256M16HA125E_RATIO,
	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,

	.cmd1csratio = MT41K256M16HA125E_RATIO,
	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,

	.cmd2csratio = MT41K256M16HA125E_RATIO,
	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
};

static const struct cmd_control ddr3_evm_cmd_ctrl_data = {
	.cmd0csratio = MT41J512M8RH125_RATIO,
	.cmd0iclkout = MT41J512M8RH125_INVERT_CLKOUT,

	.cmd1csratio = MT41J512M8RH125_RATIO,
	.cmd1iclkout = MT41J512M8RH125_INVERT_CLKOUT,

	.cmd2csratio = MT41J512M8RH125_RATIO,
	.cmd2iclkout = MT41J512M8RH125_INVERT_CLKOUT,
};

static const struct cmd_control ddr3_icev2_cmd_ctrl_data = {
	.cmd0csratio = MT41J128MJT125_RATIO_400MHz,
	.cmd0iclkout = MT41J128MJT125_INVERT_CLKOUT_400MHz,

	.cmd1csratio = MT41J128MJT125_RATIO_400MHz,
	.cmd1iclkout = MT41J128MJT125_INVERT_CLKOUT_400MHz,

	.cmd2csratio = MT41J128MJT125_RATIO_400MHz,
	.cmd2iclkout = MT41J128MJT125_INVERT_CLKOUT_400MHz,
};

static struct emif_regs ddr3_emif_reg_data = {
	.sdram_config = MT41J128MJT125_EMIF_SDCFG,
	.ref_ctrl = MT41J128MJT125_EMIF_SDREF,
	.sdram_tim1 = MT41J128MJT125_EMIF_TIM1,
	.sdram_tim2 = MT41J128MJT125_EMIF_TIM2,
	.sdram_tim3 = MT41J128MJT125_EMIF_TIM3,
	.zq_config = MT41J128MJT125_ZQ_CFG,
	.emif_ddr_phy_ctlr_1 = MT41J128MJT125_EMIF_READ_LATENCY |
				PHY_EN_DYN_PWRDN,
};

static struct emif_regs ddr3_beagleblack_emif_reg_data = {
	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
	.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
	.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
	.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
	.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
	.ocp_config = EMIF_OCP_CONFIG_BEAGLEBONE_BLACK,
	.zq_config = MT41K256M16HA125E_ZQ_CFG,
	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
};

static struct emif_regs ddr3_evm_emif_reg_data = {
	.sdram_config = MT41J512M8RH125_EMIF_SDCFG,
	.ref_ctrl = MT41J512M8RH125_EMIF_SDREF,
	.sdram_tim1 = MT41J512M8RH125_EMIF_TIM1,
	.sdram_tim2 = MT41J512M8RH125_EMIF_TIM2,
	.sdram_tim3 = MT41J512M8RH125_EMIF_TIM3,
	.ocp_config = EMIF_OCP_CONFIG_AM335X_EVM,
	.zq_config = MT41J512M8RH125_ZQ_CFG,
	.emif_ddr_phy_ctlr_1 = MT41J512M8RH125_EMIF_READ_LATENCY |
				PHY_EN_DYN_PWRDN,
};

static struct emif_regs ddr3_icev2_emif_reg_data = {
	.sdram_config = MT41J128MJT125_EMIF_SDCFG_400MHz,
	.ref_ctrl = MT41J128MJT125_EMIF_SDREF_400MHz,
	.sdram_tim1 = MT41J128MJT125_EMIF_TIM1_400MHz,
	.sdram_tim2 = MT41J128MJT125_EMIF_TIM2_400MHz,
	.sdram_tim3 = MT41J128MJT125_EMIF_TIM3_400MHz,
	.zq_config = MT41J128MJT125_ZQ_CFG_400MHz,
	.emif_ddr_phy_ctlr_1 = MT41J128MJT125_EMIF_READ_LATENCY_400MHz |
				PHY_EN_DYN_PWRDN,
};

#ifdef CONFIG_SPL_OS_BOOT
int spl_start_uboot(void)
{
#ifdef CONFIG_SPL_SERIAL_SUPPORT
	/* break into full u-boot on 'c' */
	if (serial_tstc() && serial_getc() == 'c')
		return 1;
#endif

#ifdef CONFIG_SPL_ENV_SUPPORT
	env_init();
	env_load();
	if (env_get_yesno("boot_os") != 1)
		return 1;
#endif

	return 0;
}
#endif

const struct dpll_params *get_dpll_ddr_params(void)
{
	int ind = get_sys_clk_index();

	if (board_is_evm_sk())
		return &dpll_ddr3_303MHz[ind];
	else if (board_is_pb() || board_is_bone_lt() || board_is_icev2())
		return &dpll_ddr3_400MHz[ind];
	else if (board_is_evm_15_or_later())
		return &dpll_ddr3_303MHz[ind];
	else
		return &dpll_ddr2_266MHz[ind];
}

static u8 bone_not_connected_to_ac_power(void)
{
	if (board_is_bone()) {
		uchar pmic_status_reg;
		if (tps65217_reg_read(TPS65217_STATUS,
				      &pmic_status_reg))
			return 1;
		if (!(pmic_status_reg & TPS65217_PWR_SRC_AC_BITMASK)) {
			puts("No AC power, switching to default OPP\n");
			return 1;
		}
	}
	return 0;
}

const struct dpll_params *get_dpll_mpu_params(void)
{
	int ind = get_sys_clk_index();
	int freq = am335x_get_efuse_mpu_max_freq(cdev);

	if (bone_not_connected_to_ac_power())
		freq = MPUPLL_M_600;

	if (board_is_pb() || board_is_bone_lt())
		freq = MPUPLL_M_1000;

	switch (freq) {
	case MPUPLL_M_1000:
		return &dpll_mpu_opp[ind][5];
	case MPUPLL_M_800:
		return &dpll_mpu_opp[ind][4];
	case MPUPLL_M_720:
		return &dpll_mpu_opp[ind][3];
	case MPUPLL_M_600:
		return &dpll_mpu_opp[ind][2];
	case MPUPLL_M_500:
		return &dpll_mpu_opp100;
	case MPUPLL_M_300:
		return &dpll_mpu_opp[ind][0];
	}

	return &dpll_mpu_opp[ind][0];
}

static void scale_vcores_bone(int freq)
{
	int usb_cur_lim, mpu_vdd;

	/*
	 * Only perform PMIC configurations if board rev > A1
	 * on Beaglebone White
	 */
	if (board_is_bone() && !strncmp(board_ti_get_rev(), "00A1", 4))
		return;

#ifndef CONFIG_DM_I2C
	if (i2c_probe(TPS65217_CHIP_PM))
		return;
#else
	if (power_tps65217_init(0))
		return;
#endif


	/*
	 * On Beaglebone White we need to ensure we have AC power
	 * before increasing the frequency.
	 */
	if (bone_not_connected_to_ac_power())
		freq = MPUPLL_M_600;

	/*
	 * Override what we have detected since we know if we have
	 * a Beaglebone Black it supports 1GHz.
	 */
	if (board_is_pb() || board_is_bone_lt())
		freq = MPUPLL_M_1000;

	switch (freq) {
	case MPUPLL_M_1000:
		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
		break;
	case MPUPLL_M_800:
		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
		break;
	case MPUPLL_M_720:
		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1200MV;
		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
		break;
	case MPUPLL_M_600:
	case MPUPLL_M_500:
	case MPUPLL_M_300:
	default:
		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1100MV;
		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
		break;
	}

	if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
			       TPS65217_POWER_PATH,
			       usb_cur_lim,
			       TPS65217_USB_INPUT_CUR_LIMIT_MASK))
		puts("tps65217_reg_write failure\n");

	/* Set DCDC3 (CORE) voltage to 1.10V */
	if (tps65217_voltage_update(TPS65217_DEFDCDC3,
				    TPS65217_DCDC_VOLT_SEL_1100MV)) {
		puts("tps65217_voltage_update failure\n");
		return;
	}

	/* Set DCDC2 (MPU) voltage */
	if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
		puts("tps65217_voltage_update failure\n");
		return;
	}

	/*
	 * Set LDO3, LDO4 output voltage to 3.3V for Beaglebone.
	 * Set LDO3 to 1.8V and LDO4 to 3.3V for Beaglebone Black.
	 */
	if (board_is_bone()) {
		if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
				       TPS65217_DEFLS1,
				       TPS65217_LDO_VOLTAGE_OUT_3_3,
				       TPS65217_LDO_MASK))
			puts("tps65217_reg_write failure\n");
	} else {
		if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
				       TPS65217_DEFLS1,
				       TPS65217_LDO_VOLTAGE_OUT_1_8,
				       TPS65217_LDO_MASK))
			puts("tps65217_reg_write failure\n");
	}

	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
			       TPS65217_DEFLS2,
			       TPS65217_LDO_VOLTAGE_OUT_3_3,
			       TPS65217_LDO_MASK))
		puts("tps65217_reg_write failure\n");
}

void scale_vcores_generic(int freq)
{
	int sil_rev, mpu_vdd;

	/*
	 * The GP EVM, IDK and EVM SK use a TPS65910 PMIC.  For all
	 * MPU frequencies we support we use a CORE voltage of
	 * 1.10V.  For MPU voltage we need to switch based on
	 * the frequency we are running at.
	 */
#ifndef CONFIG_DM_I2C
	if (i2c_probe(TPS65910_CTRL_I2C_ADDR))
		return;
#else
	if (power_tps65910_init(0))
		return;
#endif
	/*
	 * Depending on MPU clock and PG we will need a different
	 * VDD to drive at that speed.
	 */
	sil_rev = readl(&cdev->deviceid) >> 28;
	mpu_vdd = am335x_get_tps65910_mpu_vdd(sil_rev, freq);

	/* Tell the TPS65910 to use i2c */
	tps65910_set_i2c_control();

	/* First update MPU voltage. */
	if (tps65910_voltage_update(MPU, mpu_vdd))
		return;

	/* Second, update the CORE voltage. */
	if (tps65910_voltage_update(CORE, TPS65910_OP_REG_SEL_1_1_0))
		return;

}

void gpi2c_init(void)
{
	/* When needed to be invoked prior to BSS initialization */
	static bool first_time = true;

	if (first_time) {
		enable_i2c0_pin_mux();
#ifndef CONFIG_DM_I2C
		i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED,
			 CONFIG_SYS_OMAP24_I2C_SLAVE);
#endif
		first_time = false;
	}
}

void scale_vcores(void)
{
	int freq;

	gpi2c_init();
	freq = am335x_get_efuse_mpu_max_freq(cdev);

	if (board_is_beaglebonex())
		scale_vcores_bone(freq);
	else
		scale_vcores_generic(freq);
}

void set_uart_mux_conf(void)
{
#if CONFIG_CONS_INDEX == 1
	enable_uart0_pin_mux();
#elif CONFIG_CONS_INDEX == 2
	enable_uart1_pin_mux();
#elif CONFIG_CONS_INDEX == 3
	enable_uart2_pin_mux();
#elif CONFIG_CONS_INDEX == 4
	enable_uart3_pin_mux();
#elif CONFIG_CONS_INDEX == 5
	enable_uart4_pin_mux();
#elif CONFIG_CONS_INDEX == 6
	enable_uart5_pin_mux();
#endif
}

void set_mux_conf_regs(void)
{
	enable_board_pin_mux();
}

const struct ctrl_ioregs ioregs_evmsk = {
	.cm0ioctl		= MT41J128MJT125_IOCTRL_VALUE,
	.cm1ioctl		= MT41J128MJT125_IOCTRL_VALUE,
	.cm2ioctl		= MT41J128MJT125_IOCTRL_VALUE,
	.dt0ioctl		= MT41J128MJT125_IOCTRL_VALUE,
	.dt1ioctl		= MT41J128MJT125_IOCTRL_VALUE,
};

const struct ctrl_ioregs ioregs_bonelt = {
	.cm0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
	.cm1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
	.cm2ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
	.dt0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
	.dt1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
};

const struct ctrl_ioregs ioregs_evm15 = {
	.cm0ioctl		= MT41J512M8RH125_IOCTRL_VALUE,
	.cm1ioctl		= MT41J512M8RH125_IOCTRL_VALUE,
	.cm2ioctl		= MT41J512M8RH125_IOCTRL_VALUE,
	.dt0ioctl		= MT41J512M8RH125_IOCTRL_VALUE,
	.dt1ioctl		= MT41J512M8RH125_IOCTRL_VALUE,
};

const struct ctrl_ioregs ioregs = {
	.cm0ioctl		= MT47H128M16RT25E_IOCTRL_VALUE,
	.cm1ioctl		= MT47H128M16RT25E_IOCTRL_VALUE,
	.cm2ioctl		= MT47H128M16RT25E_IOCTRL_VALUE,
	.dt0ioctl		= MT47H128M16RT25E_IOCTRL_VALUE,
	.dt1ioctl		= MT47H128M16RT25E_IOCTRL_VALUE,
};

void sdram_init(void)
{
	if (board_is_evm_sk()) {
		/*
		 * EVM SK 1.2A and later use gpio0_7 to enable DDR3.
		 * This is safe enough to do on older revs.
		 */
		gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");
		gpio_direction_output(GPIO_DDR_VTT_EN, 1);
	}

	if (board_is_icev2()) {
		gpio_request(ICE_GPIO_DDR_VTT_EN, "ddr_vtt_en");
		gpio_direction_output(ICE_GPIO_DDR_VTT_EN, 1);
	}

	if (board_is_evm_sk())
		config_ddr(303, &ioregs_evmsk, &ddr3_data,
			   &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
	else if (board_is_pb() || board_is_bone_lt())
		config_ddr(400, &ioregs_bonelt,
			   &ddr3_beagleblack_data,
			   &ddr3_beagleblack_cmd_ctrl_data,
			   &ddr3_beagleblack_emif_reg_data, 0);
	else if (board_is_evm_15_or_later())
		config_ddr(303, &ioregs_evm15, &ddr3_evm_data,
			   &ddr3_evm_cmd_ctrl_data, &ddr3_evm_emif_reg_data, 0);
	else if (board_is_icev2())
		config_ddr(400, &ioregs_evmsk, &ddr3_icev2_data,
			   &ddr3_icev2_cmd_ctrl_data, &ddr3_icev2_emif_reg_data,
			   0);
	else if (board_is_gp_evm())
		config_ddr(266, &ioregs, &ddr2_data,
			   &ddr2_cmd_ctrl_data, &ddr2_evm_emif_reg_data, 0);
	else
		config_ddr(266, &ioregs, &ddr2_data,
			   &ddr2_cmd_ctrl_data, &ddr2_emif_reg_data, 0);
}
#endif

#if defined(CONFIG_CLOCK_SYNTHESIZER) && (!defined(CONFIG_SPL_BUILD) || \
	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)))
static void request_and_set_gpio(int gpio, char *name, int val)
{
	int ret;

	ret = gpio_request(gpio, name);
	if (ret < 0) {
		printf("%s: Unable to request %s\n", __func__, name);
		return;
	}

	ret = gpio_direction_output(gpio, 0);
	if (ret < 0) {
		printf("%s: Unable to set %s  as output\n", __func__, name);
		goto err_free_gpio;
	}

	gpio_set_value(gpio, val);

	return;

err_free_gpio:
	gpio_free(gpio);
}

#define REQUEST_AND_SET_GPIO(N)	request_and_set_gpio(N, #N, 1);
#define REQUEST_AND_CLR_GPIO(N)	request_and_set_gpio(N, #N, 0);

/**
 * RMII mode on ICEv2 board needs 50MHz clock. Given the clock
 * synthesizer With a capacitor of 18pF, and 25MHz input clock cycle
 * PLL1 gives an output of 100MHz. So, configuring the div2/3 as 2 to
 * give 50MHz output for Eth0 and 1.
 */
static struct clk_synth cdce913_data = {
	.id = 0x81,
	.capacitor = 0x90,
	.mux = 0x6d,
	.pdiv2 = 0x2,
	.pdiv3 = 0x2,
};
#endif

#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_CONTROL) && \
	defined(CONFIG_DM_ETH) && defined(CONFIG_DRIVER_TI_CPSW)

#define MAX_CPSW_SLAVES	2

/* At the moment, we do not want to stop booting for any failures here */
int ft_board_setup(void *fdt, bd_t *bd)
{
	const char *slave_path, *enet_name;
	int enetnode, slavenode, phynode;
	struct udevice *ethdev;
	char alias[16];
	u32 phy_id[2];
	int phy_addr;
	int i, ret;

	/* phy address fixup needed only on beagle bone family */
	if (!board_is_beaglebonex())
		goto done;

	for (i = 0; i < MAX_CPSW_SLAVES; i++) {
		sprintf(alias, "ethernet%d", i);

		slave_path = fdt_get_alias(fdt, alias);
		if (!slave_path)
			continue;

		slavenode = fdt_path_offset(fdt, slave_path);
		if (slavenode < 0)
			continue;

		enetnode = fdt_parent_offset(fdt, slavenode);
		enet_name = fdt_get_name(fdt, enetnode, NULL);

		ethdev = eth_get_dev_by_name(enet_name);
		if (!ethdev)
			continue;

		phy_addr = cpsw_get_slave_phy_addr(ethdev, i);

		/* check for phy_id as well as phy-handle properties */
		ret = fdtdec_get_int_array_count(fdt, slavenode, "phy_id",
						 phy_id, 2);
		if (ret == 2) {
			if (phy_id[1] != phy_addr) {
				printf("fixing up phy_id for %s, old: %d, new: %d\n",
				       alias, phy_id[1], phy_addr);

				phy_id[0] = cpu_to_fdt32(phy_id[0]);
				phy_id[1] = cpu_to_fdt32(phy_addr);
				do_fixup_by_path(fdt, slave_path, "phy_id",
						 phy_id, sizeof(phy_id), 0);
			}
		} else {
			phynode = fdtdec_lookup_phandle(fdt, slavenode,
							"phy-handle");
			if (phynode < 0)
				continue;

			ret = fdtdec_get_int(fdt, phynode, "reg", -ENOENT);
			if (ret < 0)
				continue;

			if (ret != phy_addr) {
				printf("fixing up phy-handle for %s, old: %d, new: %d\n",
				       alias, ret, phy_addr);

				fdt_setprop_u32(fdt, phynode, "reg",
						cpu_to_fdt32(phy_addr));
			}
		}
	}

done:
	return 0;
}
#endif

/*
 * Basic board specific setup.  Pinmux has been handled already.
 */
int board_init(void)
{
#if defined(CONFIG_HW_WATCHDOG)
	hw_watchdog_init();
#endif

	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#if defined(CONFIG_NOR) || defined(CONFIG_NAND)
	gpmc_init();
#endif

#if defined(CONFIG_CLOCK_SYNTHESIZER) && (!defined(CONFIG_SPL_BUILD) || \
	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)))
	if (board_is_icev2()) {
		int rv;
		u32 reg;

		REQUEST_AND_SET_GPIO(GPIO_PR1_MII_CTRL);
		/* Make J19 status available on GPIO1_26 */
		REQUEST_AND_CLR_GPIO(GPIO_MUX_MII_CTRL);

		REQUEST_AND_SET_GPIO(GPIO_FET_SWITCH_CTRL);
		/*
		 * Both ports can be set as RMII-CPSW or MII-PRU-ETH using
		 * jumpers near the port. Read the jumper value and set
		 * the pinmux, external mux and PHY clock accordingly.
		 * As jumper line is overridden by PHY RX_DV pin immediately
		 * after bootstrap (power-up/reset), we need to sample
		 * it during PHY reset using GPIO rising edge detection.
		 */
		REQUEST_AND_SET_GPIO(GPIO_PHY_RESET);
		/* Enable rising edge IRQ on GPIO0_11 and GPIO 1_26 */
		reg = readl(GPIO0_RISINGDETECT) | BIT(11);
		writel(reg, GPIO0_RISINGDETECT);
		reg = readl(GPIO1_RISINGDETECT) | BIT(26);
		writel(reg, GPIO1_RISINGDETECT);
		/* Reset PHYs to capture the Jumper setting */
		gpio_set_value(GPIO_PHY_RESET, 0);
		udelay(2);	/* PHY datasheet states 1uS min. */
		gpio_set_value(GPIO_PHY_RESET, 1);

		reg = readl(GPIO0_IRQSTATUSRAW) & BIT(11);
		if (reg) {
			writel(reg, GPIO0_IRQSTATUS1); /* clear irq */
			/* RMII mode */
			printf("ETH0, CPSW\n");
		} else {
			/* MII mode */
			printf("ETH0, PRU\n");
			cdce913_data.pdiv3 = 4;	/* 25MHz PHY clk */
		}

		reg = readl(GPIO1_IRQSTATUSRAW) & BIT(26);
		if (reg) {
			writel(reg, GPIO1_IRQSTATUS1); /* clear irq */
			/* RMII mode */
			printf("ETH1, CPSW\n");
			gpio_set_value(GPIO_MUX_MII_CTRL, 1);
		} else {
			/* MII mode */
			printf("ETH1, PRU\n");
			cdce913_data.pdiv2 = 4;	/* 25MHz PHY clk */
		}

		/* disable rising edge IRQs */
		reg = readl(GPIO0_RISINGDETECT) & ~BIT(11);
		writel(reg, GPIO0_RISINGDETECT);
		reg = readl(GPIO1_RISINGDETECT) & ~BIT(26);
		writel(reg, GPIO1_RISINGDETECT);

		rv = setup_clock_synthesizer(&cdce913_data);
		if (rv) {
			printf("Clock synthesizer setup failed %d\n", rv);
			return rv;
		}

		/* reset PHYs */
		gpio_set_value(GPIO_PHY_RESET, 0);
		udelay(2);	/* PHY datasheet states 1uS min. */
		gpio_set_value(GPIO_PHY_RESET, 1);
	}
#endif

	return 0;
}

#ifdef CONFIG_BOARD_LATE_INIT
int board_late_init(void)
{
	struct udevice *dev;
#if !defined(CONFIG_SPL_BUILD)
	uint8_t mac_addr[6];
	uint32_t mac_hi, mac_lo;
#endif

#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
	char *name = NULL;

	if (board_is_bone_lt()) {
		/* BeagleBoard.org BeagleBone Black Wireless: */
		if (!strncmp(board_ti_get_rev(), "BWA", 3)) {
			name = "BBBW";
		}
		/* SeeedStudio BeagleBone Green Wireless */
		if (!strncmp(board_ti_get_rev(), "GW1", 3)) {
			name = "BBGW";
		}
		/* BeagleBoard.org BeagleBone Blue */
		if (!strncmp(board_ti_get_rev(), "BLA", 3)) {
			name = "BBBL";
		}
	}

	if (board_is_bbg1())
		name = "BBG1";
	if (board_is_bben())
		name = "BBEN";
	set_board_info_env(name);

	/*
	 * Default FIT boot on HS devices. Non FIT images are not allowed
	 * on HS devices.
	 */
	if (get_device_type() == HS_DEVICE)
		env_set("boot_fit", "1");
#endif

#if !defined(CONFIG_SPL_BUILD)
	/* try reading mac address from efuse */
	mac_lo = readl(&cdev->macid0l);
	mac_hi = readl(&cdev->macid0h);
	mac_addr[0] = mac_hi & 0xFF;
	mac_addr[1] = (mac_hi & 0xFF00) >> 8;
	mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
	mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
	mac_addr[4] = mac_lo & 0xFF;
	mac_addr[5] = (mac_lo & 0xFF00) >> 8;

	if (!env_get("ethaddr")) {
		printf("<ethaddr> not set. Validating first E-fuse MAC\n");

		if (is_valid_ethaddr(mac_addr))
			eth_env_set_enetaddr("ethaddr", mac_addr);
	}

	mac_lo = readl(&cdev->macid1l);
	mac_hi = readl(&cdev->macid1h);
	mac_addr[0] = mac_hi & 0xFF;
	mac_addr[1] = (mac_hi & 0xFF00) >> 8;
	mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
	mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
	mac_addr[4] = mac_lo & 0xFF;
	mac_addr[5] = (mac_lo & 0xFF00) >> 8;

	if (!env_get("eth1addr")) {
		if (is_valid_ethaddr(mac_addr))
			eth_env_set_enetaddr("eth1addr", mac_addr);
	}
#endif

	if (!env_get("serial#")) {
		char *board_serial = env_get("board_serial");
		char *ethaddr = env_get("ethaddr");

		if (!board_serial || !strncmp(board_serial, "unknown", 7))
			env_set("serial#", ethaddr);
		else
			env_set("serial#", board_serial);
	}

	/* Just probe the potentially supported cdce913 device */
	uclass_get_device(UCLASS_CLK, 0, &dev);

	return 0;
}
#endif

/* CPSW platdata */
#if !CONFIG_IS_ENABLED(OF_CONTROL)
struct cpsw_slave_data slave_data[] = {
	{
		.slave_reg_ofs  = CPSW_SLAVE0_OFFSET,
		.sliver_reg_ofs = CPSW_SLIVER0_OFFSET,
		.phy_addr       = 0,
	},
	{
		.slave_reg_ofs  = CPSW_SLAVE1_OFFSET,
		.sliver_reg_ofs = CPSW_SLIVER1_OFFSET,
		.phy_addr       = 1,
	},
};

struct cpsw_platform_data am335_eth_data = {
	.cpsw_base		= CPSW_BASE,
	.version		= CPSW_CTRL_VERSION_2,
	.bd_ram_ofs		= CPSW_BD_OFFSET,
	.ale_reg_ofs		= CPSW_ALE_OFFSET,
	.cpdma_reg_ofs		= CPSW_CPDMA_OFFSET,
	.mdio_div		= CPSW_MDIO_DIV,
	.host_port_reg_ofs	= CPSW_HOST_PORT_OFFSET,
	.channels		= 8,
	.slaves			= 2,
	.slave_data		= slave_data,
	.ale_entries		= 1024,
	.bd_ram_ofs		= 0x2000,
	.mac_control		= 0x20,
	.active_slave		= 0,
	.mdio_base		= 0x4a101000,
	.gmii_sel		= 0x44e10650,
	.phy_sel_compat		= "ti,am3352-cpsw-phy-sel",
	.syscon_addr		= 0x44e10630,
	.macid_sel_compat	= "cpsw,am33xx",
};

struct eth_pdata cpsw_pdata = {
	.iobase = 0x4a100000,
	.phy_interface = 0,
	.priv_pdata = &am335_eth_data,
};

U_BOOT_DEVICE(am335x_eth) = {
	.name = "eth_cpsw",
	.platdata = &cpsw_pdata,
};
#endif

#ifdef CONFIG_SPL_LOAD_FIT
int board_fit_config_name_match(const char *name)
{
	if (board_is_gp_evm() && !strcmp(name, "am335x-evm"))
		return 0;
	else if (board_is_bone() && !strcmp(name, "am335x-bone"))
		return 0;
	else if (board_is_bone_lt() && !strcmp(name, "am335x-boneblack"))
		return 0;
	else if (board_is_pb() && !strcmp(name, "am335x-pocketbeagle"))
		return 0;
	else if (board_is_evm_sk() && !strcmp(name, "am335x-evmsk"))
		return 0;
	else if (board_is_bbg1() && !strcmp(name, "am335x-bonegreen"))
		return 0;
	else if (board_is_icev2() && !strcmp(name, "am335x-icev2"))
		return 0;
	else
		return -1;
}
#endif

#ifdef CONFIG_TI_SECURE_DEVICE
void board_fit_image_post_process(void **p_image, size_t *p_size)
{
	secure_boot_verify_image(p_image, p_size);
}
#endif

#if !CONFIG_IS_ENABLED(OF_CONTROL)
static const struct omap_hsmmc_plat am335x_mmc0_platdata = {
	.base_addr = (struct hsmmc *)OMAP_HSMMC1_BASE,
	.cfg.host_caps = MMC_MODE_HS_52MHz | MMC_MODE_HS | MMC_MODE_4BIT,
	.cfg.f_min = 400000,
	.cfg.f_max = 52000000,
	.cfg.voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195,
	.cfg.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT,
};

U_BOOT_DEVICE(am335x_mmc0) = {
	.name = "omap_hsmmc",
	.platdata = &am335x_mmc0_platdata,
};

static const struct omap_hsmmc_plat am335x_mmc1_platdata = {
	.base_addr = (struct hsmmc *)OMAP_HSMMC2_BASE,
	.cfg.host_caps = MMC_MODE_HS_52MHz | MMC_MODE_HS | MMC_MODE_8BIT,
	.cfg.f_min = 400000,
	.cfg.f_max = 52000000,
	.cfg.voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195,
	.cfg.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT,
};

U_BOOT_DEVICE(am335x_mmc1) = {
	.name = "omap_hsmmc",
	.platdata = &am335x_mmc1_platdata,
};
#endif