arch/arm/dts/sun50i-h616-orangepi-zero.dtsi

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (C) 2020 Arm Ltd.
 *
 * DT nodes common between Orange Pi Zero 2 and Orange Pi Zero 3.
 * Excludes PMIC nodes and properties, since they are different between the two.
 */

#include "sun50i-h616.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/leds/common.h>

/ {
	aliases {
		ethernet0 = &emac0;
		serial0 = &uart0;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	leds {
		compatible = "gpio-leds";

		led-0 {
			function = LED_FUNCTION_POWER;
			color = <LED_COLOR_ID_RED>;
			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
			default-state = "on";
		};

		led-1 {
			function = LED_FUNCTION_STATUS;
			color = <LED_COLOR_ID_GREEN>;
			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
		};
	};

	reg_vcc5v: vcc5v {
		/* board wide 5V supply directly from the USB-C socket */
		compatible = "regulator-fixed";
		regulator-name = "vcc-5v";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		regulator-always-on;
	};

	reg_usb1_vbus: regulator-usb1-vbus {
		compatible = "regulator-fixed";
		regulator-name = "usb1-vbus";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		vin-supply = <&reg_vcc5v>;
		enable-active-high;
		gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
	};
};

&ehci1 {
	status = "okay";
};

/* USB 2 & 3 are on headers only. */

&emac0 {
	pinctrl-names = "default";
	pinctrl-0 = <&ext_rgmii_pins>;
	phy-handle = <&ext_rgmii_phy>;
	status = "okay";
};

&mdio0 {
	ext_rgmii_phy: ethernet-phy@1 {
		compatible = "ethernet-phy-ieee802.3-c22";
		reg = <1>;
	};
};

&mmc0 {
	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
	bus-width = <4>;
	status = "okay";
};

&ohci1 {
	status = "okay";
};

&spi0  {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;

	flash@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <40000000>;
	};
};

&uart0 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart0_ph_pins>;
	status = "okay";
};

&usbotg {
	/*
	 * PHY0 pins are connected to a USB-C socket, but a role switch
	 * is not implemented: both CC pins are pulled to GND.
	 * The VBUS pins power the device, so a fixed peripheral mode
	 * is the best choice.
	 * The board can be powered via GPIOs, in this case port0 *can*
	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
	 * then provided by the GPIOs. Any user of this setup would
	 * need to adjust the DT accordingly: dr_mode set to "host",
	 * enabling OHCI0 and EHCI0.
	 */
	dr_mode = "peripheral";
	status = "okay";
};

&usbphy {
	usb1_vbus-supply = <&reg_usb1_vbus>;
	status = "okay";
};