Gitiles
Code Review Sign In
git01.mediatek.com / filogic / uboot / 022c2e2bfd718e402692dbbc080cbc3552059033 / . / board / sbc8240 / README
blob: 71595b4bffbed4edf9a4b62d7ca92e7160f85f4a [file] [log] [blame]
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]1The supported features of the SBC8240/8245 board are:
2 8240 or 8245 processor
3 66MHz & 100MHz bus speed
4 Decrementer timer
5 1 UART channel (Console channel)
6 8240 Interrupt Controller
7 8240 PCI bridge
8 8240 Memory Controller
9 SDRAM (16, 64 MB Memory DIMM)
10 FLASH 512K On board
11 FLASH 4MB On board
12
13
14Memory Map from CPU point of view:
15
wdenkb5bb1392004-07-10 23:11:10 +0000[diff] [blame]16 Start Size Access to
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]17 -----------------------------------------------------
wdenkb5bb1392004-07-10 23:11:10 +0000[diff] [blame]18 0x00000000 64MB SDRAM DIMM
19 0xFF000000 4MB On Board FLASH
20 0xFFF00000 512K On Board FLASH or SRAM (Configured by jumper)
21 0xFFE00000 8K EEPROM
22 0xFFE80000 8Bit LED
23 0xFFF80000 8Bit UART
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]24
25
26Setting the board Jumpers & Switches:
27
28 In order to get the board running with the default configuration the
29 jumpers need to be set as follows:
30
31 General Jumpers:
32 ____________________________________________
wdenkb5bb1392004-07-10 23:11:10 +0000[diff] [blame]33 | Jumpers | Jumpers | Jumpers |
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]34 |-------------|--------------|---------------|
wdenkb5bb1392004-07-10 23:11:10 +0000[diff] [blame]35 |JP1 1-2 | JP14 1-2 | JP27 1-2 |
36 |JP5 Open | JP15 1-2 | JP28 2-3 |
37 |JP8 1-2 | JP16 1-2 | JP33 Open |
38 |JP9 1-2 | JP17 1-2 | JP37 Close |
39 |JP10 1-2 | JP18 1-2 | |
40 |JP11 2-3 | JP19 1-2 | |
41 |JP12 1-2 | JP20 1-2 | |
42 |JP13 1-2 | JP25 Open | |
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]43 |_____________|______________|_______________|
44
45 Bus speed Jumpers:
46 _________________________
47 | 100MHz Bus | 66 MHz Bus |
48 |------------|------------|
wdenkb5bb1392004-07-10 23:11:10 +0000[diff] [blame]49 | JP2 1-2 | JP2 1-2 |
50 | JP3 1-2 | JP3 2-3 |
51 | JP4 1-2 | JP4 2-3 |
52 | JP6 1-2 | JP6 2-3 |
53 | JP7 1-2 | JP7 1-2 |
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]54 |____________|____________|
55
56
57U-Boot 1.1.2 (Jun 24 2004 - 17:01:04)
58
59CPU: MPC8240 Revision 1.1 at 247.500 MHz: 16 kB I-Cache 16 kB D-Cache
60Board: sbc8240 Revision 255 Local Bus at 99 MHz
61DRAM: 64 MB
62FLASH: 512 kB
wdenkb5bb1392004-07-10 23:11:10 +0000[diff] [blame]63 00 11 8086 1229 0200 00
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]64In: serial
65Out: serial
66Err: serial
67Net: i82559#0
68
69Welcome to U-Boot for the sbc8240
70
71Type ? or help to get on-line help
72
73Hit any key to stop autoboot: 0
74=> printenv
75bootcmd=version;echo;tftpboot $loadaddr $loadfile;bootvx
76bootdelay=5
77baudrate=9600
78ethaddr=DE:AD:BE:EF:01:01
79ipaddr=192.168.193.102
80preboot=echo;echo Welcome to U-Boot for the sbc8240;echo;echo Type "? or help" to get on-line help;echo
81netmask=255.255.255.248
82clocks_in_mhz=1
83bootargs=$fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 tn=sbc8240 o=fei
84ipaddr=192.168.193.102
85loadfile=vxWorks.st
86loadaddr=0x01000000
87net_load=tftpboot $loadaddr $loadfile
88serverip=192.168.193.99
89ethact=i82559#0
90stdin=serial
91stdout=serial
92stderr=serial
93
94Environment size: 631/16380 bytes
95=> boot
96
97U-Boot 1.1.2 (Jun 24 2004 - 17:01:04)
98
99Using i82559#0 device
100TFTP from server 192.168.193.99; our IP address is 192.168.193.102
101Filename 'vxWorks.st'.
102Load address: 0x1000000
103Loading: #################################################################
wdenkb5bb1392004-07-10 23:11:10 +0000[diff] [blame]104 #################################################################
105 ##############################################################
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]106done
107Bytes transferred = 979927 (ef3d7 hex)
108## Ethernet MAC address not copied to NV RAM
109Loading .text @ 0x00100000 (758848 bytes)
110Loading .data @ 0x001b9440 (79904 bytes)
111Clearing .bss @ 0x001ccc60 (20288 bytes)
112## Using bootline (@ 0x4200): $fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 tn=sbc8240 o=fei
113## Starting vxWorks at 0x00100000 ...
114
115Adding 2845 symbols for standalone.
116
117
118 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
119 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
120 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
wdenkb5bb1392004-07-10 23:11:10 +0000[diff] [blame]121 ]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R)
122 ] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]]
123 ]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]]
124 ]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]]
125 ]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]]
126 ]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]]
127 ]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]]
128 ]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]]
129 ]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]]
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]130 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
wdenkb5bb1392004-07-10 23:11:10 +0000[diff] [blame]131 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]132 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]
wdenkb5bb1392004-07-10 23:11:10 +0000[diff] [blame]133 ]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks version 5.5.1
134 ]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.6
135 ]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2003
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]136
wdenkb5bb1392004-07-10 23:11:10 +0000[diff] [blame]137 CPU: MPC8240 -- Wind River BSP. SBC8240 Board. Processor #0.
138 Memory Size: 0x2000000. BSP version 1.2/28.
wdenk265d2172004-07-10 22:35:59 +0000[diff] [blame]139
140->