| wdenk | 265d217 | 2004-07-10 22:35:59 +0000 | [diff] [blame^] | 1 | The supported features of the SBC8240/8245 board are: |
| 2 | 8240 or 8245 processor |
| 3 | 66MHz & 100MHz bus speed |
| 4 | Decrementer timer |
| 5 | 1 UART channel (Console channel) |
| 6 | 8240 Interrupt Controller |
| 7 | 8240 PCI bridge |
| 8 | 8240 Memory Controller |
| 9 | SDRAM (16, 64 MB Memory DIMM) |
| 10 | FLASH 512K On board |
| 11 | FLASH 4MB On board |
| 12 | |
| 13 | |
| 14 | Memory Map from CPU point of view: |
| 15 | |
| 16 | Start Size Access to |
| 17 | ----------------------------------------------------- |
| 18 | 0x00000000 64MB SDRAM DIMM |
| 19 | 0xFF000000 4MB On Board FLASH |
| 20 | 0xFFF00000 512K On Board FLASH or SRAM (Configured by jumper) |
| 21 | 0xFFE00000 8K EEPROM |
| 22 | 0xFFE80000 8Bit LED |
| 23 | 0xFFF80000 8Bit UART |
| 24 | |
| 25 | |
| 26 | Setting the board Jumpers & Switches: |
| 27 | |
| 28 | In order to get the board running with the default configuration the |
| 29 | jumpers need to be set as follows: |
| 30 | |
| 31 | General Jumpers: |
| 32 | ____________________________________________ |
| 33 | | Jumpers | Jumpers | Jumpers | |
| 34 | |-------------|--------------|---------------| |
| 35 | |JP1 1-2 | JP14 1-2 | JP27 1-2 | |
| 36 | |JP5 Open | JP15 1-2 | JP28 2-3 | |
| 37 | |JP8 1-2 | JP16 1-2 | JP33 Open | |
| 38 | |JP9 1-2 | JP17 1-2 | JP37 Close | |
| 39 | |JP10 1-2 | JP18 1-2 | | |
| 40 | |JP11 2-3 | JP19 1-2 | | |
| 41 | |JP12 1-2 | JP20 1-2 | | |
| 42 | |JP13 1-2 | JP25 Open | | |
| 43 | |_____________|______________|_______________| |
| 44 | |
| 45 | Bus speed Jumpers: |
| 46 | _________________________ |
| 47 | | 100MHz Bus | 66 MHz Bus | |
| 48 | |------------|------------| |
| 49 | | JP2 1-2 | JP2 1-2 | |
| 50 | | JP3 1-2 | JP3 2-3 | |
| 51 | | JP4 1-2 | JP4 2-3 | |
| 52 | | JP6 1-2 | JP6 2-3 | |
| 53 | | JP7 1-2 | JP7 1-2 | |
| 54 | |____________|____________| |
| 55 | |
| 56 | |
| 57 | U-Boot 1.1.2 (Jun 24 2004 - 17:01:04) |
| 58 | |
| 59 | CPU: MPC8240 Revision 1.1 at 247.500 MHz: 16 kB I-Cache 16 kB D-Cache |
| 60 | Board: sbc8240 Revision 255 Local Bus at 99 MHz |
| 61 | DRAM: 64 MB |
| 62 | FLASH: 512 kB |
| 63 | 00 11 8086 1229 0200 00 |
| 64 | In: serial |
| 65 | Out: serial |
| 66 | Err: serial |
| 67 | Net: i82559#0 |
| 68 | |
| 69 | Welcome to U-Boot for the sbc8240 |
| 70 | |
| 71 | Type ? or help to get on-line help |
| 72 | |
| 73 | Hit any key to stop autoboot: 0 |
| 74 | => printenv |
| 75 | bootcmd=version;echo;tftpboot $loadaddr $loadfile;bootvx |
| 76 | bootdelay=5 |
| 77 | baudrate=9600 |
| 78 | ethaddr=DE:AD:BE:EF:01:01 |
| 79 | ipaddr=192.168.193.102 |
| 80 | preboot=echo;echo Welcome to U-Boot for the sbc8240;echo;echo Type "? or help" to get on-line help;echo |
| 81 | netmask=255.255.255.248 |
| 82 | clocks_in_mhz=1 |
| 83 | bootargs=$fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 tn=sbc8240 o=fei |
| 84 | ipaddr=192.168.193.102 |
| 85 | loadfile=vxWorks.st |
| 86 | loadaddr=0x01000000 |
| 87 | net_load=tftpboot $loadaddr $loadfile |
| 88 | serverip=192.168.193.99 |
| 89 | ethact=i82559#0 |
| 90 | stdin=serial |
| 91 | stdout=serial |
| 92 | stderr=serial |
| 93 | |
| 94 | Environment size: 631/16380 bytes |
| 95 | => boot |
| 96 | |
| 97 | U-Boot 1.1.2 (Jun 24 2004 - 17:01:04) |
| 98 | |
| 99 | Using i82559#0 device |
| 100 | TFTP from server 192.168.193.99; our IP address is 192.168.193.102 |
| 101 | Filename 'vxWorks.st'. |
| 102 | Load address: 0x1000000 |
| 103 | Loading: ################################################################# |
| 104 | ################################################################# |
| 105 | ############################################################## |
| 106 | done |
| 107 | Bytes transferred = 979927 (ef3d7 hex) |
| 108 | ## Ethernet MAC address not copied to NV RAM |
| 109 | Loading .text @ 0x00100000 (758848 bytes) |
| 110 | Loading .data @ 0x001b9440 (79904 bytes) |
| 111 | Clearing .bss @ 0x001ccc60 (20288 bytes) |
| 112 | ## Using bootline (@ 0x4200): $fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 tn=sbc8240 o=fei |
| 113 | ## Starting vxWorks at 0x00100000 ... |
| 114 | |
| 115 | Adding 2845 symbols for standalone. |
| 116 | |
| 117 | |
| 118 | ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] |
| 119 | ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] |
| 120 | ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] |
| 121 | ]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R) |
| 122 | ] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]] |
| 123 | ]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]] |
| 124 | ]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]] |
| 125 | ]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]] |
| 126 | ]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]] |
| 127 | ]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]] |
| 128 | ]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]] |
| 129 | ]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]] |
| 130 | ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] |
| 131 | ]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System |
| 132 | ]]]]]]]]]]]]]]]]]]]]]]]]]]]] |
| 133 | ]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks version 5.5.1 |
| 134 | ]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.6 |
| 135 | ]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2003 |
| 136 | |
| 137 | CPU: MPC8240 -- Wind River BSP. SBC8240 Board. Processor #0. |
| 138 | Memory Size: 0x2000000. BSP version 1.2/28. |
| 139 | |
| 140 | -> |