arch/arm/cpu/armv7/sunxi/board.c

/*
 * (C) Copyright 2012 Henrik Nordstrom <henrik@henriknordstrom.net>
 *
 * (C) Copyright 2007-2011
 * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
 * Tom Cubie <tangliang@allwinnertech.com>
 *
 * Some init for sunxi platform.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <mmc.h>
#include <i2c.h>
#include <serial.h>
#ifdef CONFIG_SPL_BUILD
#include <spl.h>
#endif
#include <asm/gpio.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/timer.h>
#include <asm/arch/tzpc.h>
#include <asm/arch/mmc.h>

#include <linux/compiler.h>

struct fel_stash {
	uint32_t sp;
	uint32_t lr;
	uint32_t cpsr;
	uint32_t sctlr;
	uint32_t vbar;
	uint32_t cr;
};

struct fel_stash fel_stash __attribute__((section(".data")));

static int gpio_init(void)
{
#if CONFIG_CONS_INDEX == 1 && defined(CONFIG_UART0_PORT_F)
#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I)
	/* disable GPB22,23 as uart0 tx,rx to avoid conflict */
	sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUNXI_GPIO_INPUT);
	sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUNXI_GPIO_INPUT);
#endif
#if defined(CONFIG_MACH_SUN8I)
	sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUN8I_GPF_UART0);
	sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUN8I_GPF_UART0);
#else
	sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUNXI_GPF_UART0);
	sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUNXI_GPF_UART0);
#endif
	sunxi_gpio_set_pull(SUNXI_GPF(4), 1);
#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I))
	sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUN4I_GPB_UART0);
	sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUN4I_GPB_UART0);
	sunxi_gpio_set_pull(SUNXI_GPB(23), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN5I)
	sunxi_gpio_set_cfgpin(SUNXI_GPB(19), SUN5I_GPB_UART0);
	sunxi_gpio_set_cfgpin(SUNXI_GPB(20), SUN5I_GPB_UART0);
	sunxi_gpio_set_pull(SUNXI_GPB(20), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN6I)
	sunxi_gpio_set_cfgpin(SUNXI_GPH(20), SUN6I_GPH_UART0);
	sunxi_gpio_set_cfgpin(SUNXI_GPH(21), SUN6I_GPH_UART0);
	sunxi_gpio_set_pull(SUNXI_GPH(21), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN8I_A33)
	sunxi_gpio_set_cfgpin(SUNXI_GPB(0), SUN8I_A33_GPB_UART0);
	sunxi_gpio_set_cfgpin(SUNXI_GPB(1), SUN8I_A33_GPB_UART0);
	sunxi_gpio_set_pull(SUNXI_GPB(1), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN9I)
	sunxi_gpio_set_cfgpin(SUNXI_GPH(12), SUN9I_GPH_UART0);
	sunxi_gpio_set_cfgpin(SUNXI_GPH(13), SUN9I_GPH_UART0);
	sunxi_gpio_set_pull(SUNXI_GPH(13), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 2 && defined(CONFIG_MACH_SUN5I)
	sunxi_gpio_set_cfgpin(SUNXI_GPG(3), SUN5I_GPG_UART1);
	sunxi_gpio_set_cfgpin(SUNXI_GPG(4), SUN5I_GPG_UART1);
	sunxi_gpio_set_pull(SUNXI_GPG(4), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 3 && defined(CONFIG_MACH_SUN8I)
	sunxi_gpio_set_cfgpin(SUNXI_GPB(0), SUN8I_GPB_UART2);
	sunxi_gpio_set_cfgpin(SUNXI_GPB(1), SUN8I_GPB_UART2);
	sunxi_gpio_set_pull(SUNXI_GPB(1), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 5 && defined(CONFIG_MACH_SUN8I)
	sunxi_gpio_set_cfgpin(SUNXI_GPL(2), SUN8I_GPL_R_UART);
	sunxi_gpio_set_cfgpin(SUNXI_GPL(3), SUN8I_GPL_R_UART);
	sunxi_gpio_set_pull(SUNXI_GPL(3), SUNXI_GPIO_PULL_UP);
#else
#error Unsupported console port number. Please fix pin mux settings in board.c
#endif

	return 0;
}

void spl_board_load_image(void)
{
	debug("Returning to FEL sp=%x, lr=%x\n", fel_stash.sp, fel_stash.lr);
	return_to_fel(fel_stash.sp, fel_stash.lr);
}

void s_init(void)
{
#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I_A23
	/* Magic (undocmented) value taken from boot0, without this DRAM
	 * access gets messed up (seems cache related) */
	setbits_le32(SUNXI_SRAMC_BASE + 0x44, 0x1800);
#endif
#if defined CONFIG_MACH_SUN6I || \
    defined CONFIG_MACH_SUN7I || \
    defined CONFIG_MACH_SUN8I
	/* Enable SMP mode for CPU0, by setting bit 6 of Auxiliary Ctl reg */
	asm volatile(
		"mrc p15, 0, r0, c1, c0, 1\n"
		"orr r0, r0, #1 << 6\n"
		"mcr p15, 0, r0, c1, c0, 1\n");
#endif
#if defined CONFIG_MACH_SUN6I
	/* Enable non-secure access to the RTC */
	tzpc_init();
#endif

	clock_init();
	timer_init();
	gpio_init();
	i2c_init_board();
}

#ifdef CONFIG_SPL_BUILD
DECLARE_GLOBAL_DATA_PTR;

/* The sunxi internal brom will try to loader external bootloader
 * from mmc0, nand flash, mmc2.
 */
u32 spl_boot_device(void)
{
	struct mmc *mmc0, *mmc1;
	/*
	 * When booting from the SD card or NAND memory, the "eGON.BT0"
	 * signature is expected to be found in memory at the address 0x0004
	 * (see the "mksunxiboot" tool, which generates this header).
	 *
	 * When booting in the FEL mode over USB, this signature is patched in
	 * memory and replaced with something else by the 'fel' tool. This other
	 * signature is selected in such a way, that it can't be present in a
	 * valid bootable SD card image (because the BROM would refuse to
	 * execute the SPL in this case).
	 *
	 * This checks for the signature and if it is not found returns to
	 * the FEL code in the BROM to wait and receive the main u-boot
	 * binary over USB. If it is found, it determines where SPL was
	 * read from.
	 */
	if (readl(4) != 0x4E4F4765 || readl(8) != 0x3054422E) /* eGON.BT0 */
		return BOOT_DEVICE_BOARD;

	/* The BROM will try to boot from mmc0 first, so try that first. */
	mmc_initialize(gd->bd);
	mmc0 = find_mmc_device(0);
	if (sunxi_mmc_has_egon_boot_signature(mmc0))
		return BOOT_DEVICE_MMC1;

	/* Fallback to booting NAND if enabled. */
	if (IS_ENABLED(CONFIG_SPL_NAND_SUPPORT))
		return BOOT_DEVICE_NAND;

	if (CONFIG_MMC_SUNXI_SLOT_EXTRA == 2) {
		mmc1 = find_mmc_device(1);
		if (sunxi_mmc_has_egon_boot_signature(mmc1)) {
			/*
			 * spl_mmc.c: spl_mmc_load_image() is hard-coded to
			 * use find_mmc_device(0), no matter what we
			 * return. Swap mmc0 and mmc2 to make this work.
			 */
			mmc0->block_dev.dev = 1;
			mmc1->block_dev.dev = 0;
			return BOOT_DEVICE_MMC2;
		}
	}

	panic("Could not determine boot source\n");
	return -1;		/* Never reached */
}

/* No confirmation data available in SPL yet. Hardcode bootmode */
u32 spl_boot_mode(void)
{
	return MMCSD_MODE_RAW;
}

void board_init_f(ulong dummy)
{
	preloader_console_init();

#ifdef CONFIG_SPL_I2C_SUPPORT
	/* Needed early by sunxi_board_init if PMU is enabled */
	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
#endif
	sunxi_board_init();
}
#endif

void reset_cpu(ulong addr)
{
#ifdef CONFIG_SUNXI_GEN_SUN4I
	static const struct sunxi_wdog *wdog =
		 &((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;

	/* Set the watchdog for its shortest interval (.5s) and wait */
	writel(WDT_MODE_RESET_EN | WDT_MODE_EN, &wdog->mode);
	writel(WDT_CTRL_KEY | WDT_CTRL_RESTART, &wdog->ctl);

	while (1) {
		/* sun5i sometimes gets stuck without this */
		writel(WDT_MODE_RESET_EN | WDT_MODE_EN, &wdog->mode);
	}
#endif
#ifdef CONFIG_SUNXI_GEN_SUN6I
	static const struct sunxi_wdog *wdog =
		 ((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;

	/* Set the watchdog for its shortest interval (.5s) and wait */
	writel(WDT_CFG_RESET, &wdog->cfg);
	writel(WDT_MODE_EN, &wdog->mode);
	writel(WDT_CTRL_KEY | WDT_CTRL_RESTART, &wdog->ctl);
	while (1) { }
#endif
}

#ifndef CONFIG_SYS_DCACHE_OFF
void enable_caches(void)
{
	/* Enable D-cache. I-cache is already enabled in start.S */
	dcache_enable();
}
#endif

#ifdef CONFIG_CMD_NET
/*
 * Initializes on-chip ethernet controllers.
 * to override, implement board_eth_init()
 */
int cpu_eth_init(bd_t *bis)
{
	__maybe_unused int rc;

#ifdef CONFIG_MACPWR
	gpio_request(CONFIG_MACPWR, "macpwr");
	gpio_direction_output(CONFIG_MACPWR, 1);
	mdelay(200);
#endif

#ifdef CONFIG_SUNXI_GMAC
	rc = sunxi_gmac_initialize(bis);
	if (rc < 0) {
		printf("sunxi: failed to initialize gmac\n");
		return rc;
	}
#endif

	return 0;
}
#endif