| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright 2017, 2019-2021 NXP |
| * Copyright 2015 Freescale Semiconductor |
| */ |
| |
| #ifndef __LS2_RDB_H |
| #define __LS2_RDB_H |
| |
| #include "ls2080a_common.h" |
| |
| #define I2C_MUX_CH_VOL_MONITOR 0xa |
| #define I2C_VOL_MONITOR_ADDR 0x38 |
| |
| /* step the IR regulator in 5mV increments */ |
| #define IR_VDD_STEP_DOWN 5 |
| #define IR_VDD_STEP_UP 5 |
| /* The lowest and highest voltage allowed for LS2080ARDB */ |
| #define VDD_MV_MIN 819 |
| #define VDD_MV_MAX 1212 |
| |
| #define COUNTER_FREQUENCY_REAL (get_board_sys_clk()/4) |
| |
| #define CONFIG_MEM_INIT_VALUE 0xdeadbeef |
| #define SPD_EEPROM_ADDRESS1 0x51 |
| #define SPD_EEPROM_ADDRESS2 0x52 |
| #define SPD_EEPROM_ADDRESS3 0x53 |
| #define SPD_EEPROM_ADDRESS4 0x54 |
| #define SPD_EEPROM_ADDRESS5 0x55 |
| #define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */ |
| #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 |
| |
| #if !defined(CONFIG_FSL_QSPI) || defined(CONFIG_TFABOOT) |
| |
| #define CFG_SYS_NOR0_CSPR_EXT (0x0) |
| #define CFG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) |
| #define CFG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024) |
| |
| #define CFG_SYS_NOR0_CSPR \ |
| (CSPR_PHYS_ADDR(CFG_SYS_FLASH_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CFG_SYS_NOR0_CSPR_EARLY \ |
| (CSPR_PHYS_ADDR(CFG_SYS_FLASH_BASE_PHYS_EARLY) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CFG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12) |
| #define CFG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ |
| FTIM0_NOR_TEADC(0x5) | \ |
| FTIM0_NOR_TEAHC(0x5)) |
| #define CFG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ |
| FTIM1_NOR_TRAD_NOR(0x1a) |\ |
| FTIM1_NOR_TSEQRAD_NOR(0x13)) |
| #define CFG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ |
| FTIM2_NOR_TCH(0x4) | \ |
| FTIM2_NOR_TWPH(0x0E) | \ |
| FTIM2_NOR_TWP(0x1c)) |
| #define CFG_SYS_NOR_FTIM3 0x04000000 |
| #define CFG_SYS_IFC_CCR 0x01000000 |
| |
| #ifdef CONFIG_MTD_NOR_FLASH |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CFG_SYS_FLASH_BANKS_LIST { CFG_SYS_FLASH_BASE,\ |
| CFG_SYS_FLASH_BASE + 0x40000000} |
| #endif |
| |
| #define CFG_SYS_NAND_CSPR_EXT (0x0) |
| #define CFG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ |
| | CSPR_MSEL_NAND /* MSEL = NAND */ \ |
| | CSPR_V) |
| #define CFG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) |
| |
| #define CFG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ |
| | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ |
| | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ |
| | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ |
| | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ |
| | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ |
| | CSOR_NAND_PB(128)) /* Pages Per Block 128*/ |
| |
| /* ONFI NAND Flash mode0 Timing Params */ |
| #define CFG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) | \ |
| FTIM0_NAND_TWP(0x30) | \ |
| FTIM0_NAND_TWCHT(0x0e) | \ |
| FTIM0_NAND_TWH(0x14)) |
| #define CFG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) | \ |
| FTIM1_NAND_TWBE(0xab) | \ |
| FTIM1_NAND_TRR(0x1c) | \ |
| FTIM1_NAND_TRP(0x30)) |
| #define CFG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) | \ |
| FTIM2_NAND_TREH(0x14) | \ |
| FTIM2_NAND_TWHRE(0x3c)) |
| #define CFG_SYS_NAND_FTIM3 0x0 |
| |
| #define CFG_SYS_NAND_BASE_LIST { CFG_SYS_NAND_BASE } |
| #define CONFIG_MTD_NAND_VERIFY_WRITE |
| |
| #define QIXIS_LBMAP_SWITCH 0x06 |
| #define QIXIS_LBMAP_MASK 0x0f |
| #define QIXIS_LBMAP_SHIFT 0 |
| #define QIXIS_LBMAP_DFLTBANK 0x00 |
| #define QIXIS_LBMAP_ALTBANK 0x04 |
| #define QIXIS_LBMAP_NAND 0x09 |
| #define QIXIS_RST_CTL_RESET 0x31 |
| #define QIXIS_RST_CTL_RESET_EN 0x30 |
| #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 |
| #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 |
| #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 |
| #define QIXIS_RCW_SRC_NAND 0x119 |
| #define QIXIS_RST_FORCE_MEM 0x01 |
| |
| #define CFG_SYS_CSPR3_EXT (0x0) |
| #define CFG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| #define CFG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| |
| #define CFG_SYS_AMASK3 IFC_AMASK(64*1024) |
| #define CFG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12) |
| /* QIXIS Timing parameters for IFC CS3 */ |
| #define CFG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ |
| FTIM0_GPCM_TEADC(0x0e) | \ |
| FTIM0_GPCM_TEAHC(0x0e)) |
| #define CFG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ |
| FTIM1_GPCM_TRAD(0x3f)) |
| #define CFG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ |
| FTIM2_GPCM_TCH(0xf) | \ |
| FTIM2_GPCM_TWP(0x3E)) |
| #define CFG_SYS_CS3_FTIM3 0x0 |
| |
| #if defined(CONFIG_SPL) && defined(CONFIG_MTD_RAW_NAND) |
| #define CFG_SYS_CSPR2_EXT CFG_SYS_NOR0_CSPR_EXT |
| #define CFG_SYS_CSPR2 CFG_SYS_NOR0_CSPR_EARLY |
| #define CFG_SYS_CSPR2_FINAL CFG_SYS_NOR0_CSPR |
| #define CFG_SYS_AMASK2 CFG_SYS_NOR_AMASK |
| #define CFG_SYS_CSOR2 CFG_SYS_NOR_CSOR |
| #define CFG_SYS_CS2_FTIM0 CFG_SYS_NOR_FTIM0 |
| #define CFG_SYS_CS2_FTIM1 CFG_SYS_NOR_FTIM1 |
| #define CFG_SYS_CS2_FTIM2 CFG_SYS_NOR_FTIM2 |
| #define CFG_SYS_CS2_FTIM3 CFG_SYS_NOR_FTIM3 |
| #define CFG_SYS_CSPR0_EXT CFG_SYS_NAND_CSPR_EXT |
| #define CFG_SYS_CSPR0 CFG_SYS_NAND_CSPR |
| #define CFG_SYS_AMASK0 CFG_SYS_NAND_AMASK |
| #define CFG_SYS_CSOR0 CFG_SYS_NAND_CSOR |
| #define CFG_SYS_CS0_FTIM0 CFG_SYS_NAND_FTIM0 |
| #define CFG_SYS_CS0_FTIM1 CFG_SYS_NAND_FTIM1 |
| #define CFG_SYS_CS0_FTIM2 CFG_SYS_NAND_FTIM2 |
| #define CFG_SYS_CS0_FTIM3 CFG_SYS_NAND_FTIM3 |
| |
| #define CFG_SYS_NAND_U_BOOT_SIZE (512 * 1024) |
| #else |
| #define CFG_SYS_CSPR0_EXT CFG_SYS_NOR0_CSPR_EXT |
| #define CFG_SYS_CSPR0 CFG_SYS_NOR0_CSPR_EARLY |
| #define CFG_SYS_CSPR0_FINAL CFG_SYS_NOR0_CSPR |
| #define CFG_SYS_AMASK0 CFG_SYS_NOR_AMASK |
| #define CFG_SYS_CSOR0 CFG_SYS_NOR_CSOR |
| #define CFG_SYS_CS0_FTIM0 CFG_SYS_NOR_FTIM0 |
| #define CFG_SYS_CS0_FTIM1 CFG_SYS_NOR_FTIM1 |
| #define CFG_SYS_CS0_FTIM2 CFG_SYS_NOR_FTIM2 |
| #define CFG_SYS_CS0_FTIM3 CFG_SYS_NOR_FTIM3 |
| #define CFG_SYS_CSPR2_EXT CFG_SYS_NAND_CSPR_EXT |
| #define CFG_SYS_CSPR2 CFG_SYS_NAND_CSPR |
| #define CFG_SYS_AMASK2 CFG_SYS_NAND_AMASK |
| #define CFG_SYS_CSOR2 CFG_SYS_NAND_CSOR |
| #define CFG_SYS_CS2_FTIM0 CFG_SYS_NAND_FTIM0 |
| #define CFG_SYS_CS2_FTIM1 CFG_SYS_NAND_FTIM1 |
| #define CFG_SYS_CS2_FTIM2 CFG_SYS_NAND_FTIM2 |
| #define CFG_SYS_CS2_FTIM3 CFG_SYS_NAND_FTIM3 |
| #endif |
| #endif |
| #define CFG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 |
| |
| #ifdef CONFIG_TARGET_LS2081ARDB |
| #define QIXIS_QMAP_MASK 0x07 |
| #define QIXIS_QMAP_SHIFT 5 |
| #define QIXIS_LBMAP_DFLTBANK 0x00 |
| #define QIXIS_LBMAP_QSPI 0x00 |
| #define QIXIS_RCW_SRC_QSPI 0x62 |
| #define QIXIS_LBMAP_ALTBANK 0x20 |
| #define QIXIS_RST_CTL_RESET 0x31 |
| #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 |
| #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 |
| #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 |
| #define QIXIS_LBMAP_MASK 0x0f |
| #define QIXIS_RST_CTL_RESET_EN 0x30 |
| #endif |
| |
| /* |
| * I2C |
| */ |
| #ifdef CONFIG_TARGET_LS2081ARDB |
| #define CFG_SYS_I2C_FPGA_ADDR 0x66 |
| #endif |
| #define I2C_MUX_PCA_ADDR 0x75 |
| #define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/ |
| |
| /* I2C bus multiplexer */ |
| #define I2C_MUX_CH_DEFAULT 0x8 |
| |
| /* SPI */ |
| |
| /* |
| * RTC configuration |
| */ |
| #define RTC |
| #ifdef CONFIG_TARGET_LS2081ARDB |
| #define CFG_SYS_I2C_RTC_ADDR 0x51 |
| #else |
| #define CONFIG_RTC_DS3231 1 |
| #define CFG_SYS_I2C_RTC_ADDR 0x68 |
| #endif |
| |
| #define BOOT_TARGET_DEVICES(func) \ |
| func(USB, usb, 0) \ |
| func(MMC, mmc, 0) \ |
| func(SCSI, scsi, 0) \ |
| func(DHCP, dhcp, na) |
| #include <config_distro_bootcmd.h> |
| |
| #ifdef CONFIG_TFABOOT |
| #define QSPI_MC_INIT_CMD \ |
| "sf probe 0:0; " \ |
| "sf read 0x80640000 0x640000 0x80000; " \ |
| "env exists secureboot && " \ |
| "esbc_validate 0x80640000 && " \ |
| "esbc_validate 0x80680000; " \ |
| "sf read 0x80a00000 0xa00000 0x200000; " \ |
| "sf read 0x80e00000 0xe00000 0x100000; " \ |
| "fsl_mc start mc 0x80a00000 0x80e00000 \0" |
| #define SD_MC_INIT_CMD \ |
| "mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \ |
| "mmc read 0x80e00000 0x7000 0x800;" \ |
| "env exists secureboot && " \ |
| "mmc read 0x80640000 0x3200 0x20 && " \ |
| "mmc read 0x80680000 0x3400 0x20 && " \ |
| "esbc_validate 0x80640000 && " \ |
| "esbc_validate 0x80680000 ;" \ |
| "fsl_mc start mc 0x80a00000 0x80e00000\0" |
| #define IFC_MC_INIT_CMD \ |
| "env exists secureboot && " \ |
| "esbc_validate 0x580640000 && " \ |
| "esbc_validate 0x580680000; " \ |
| "fsl_mc start mc 0x580a00000 0x580e00000 \0" |
| #else |
| #ifdef CONFIG_QSPI_BOOT |
| #define MC_INIT_CMD \ |
| "mcinitcmd=sf probe 0:0; " \ |
| "sf read 0x80640000 0x640000 0x80000; " \ |
| "env exists secureboot && " \ |
| "esbc_validate 0x80640000 && " \ |
| "esbc_validate 0x80680000; " \ |
| "sf read 0x80a00000 0xa00000 0x200000; " \ |
| "sf read 0x80e00000 0xe00000 0x100000; " \ |
| "fsl_mc start mc 0x80a00000 0x80e00000 \0" |
| #elif defined(CONFIG_SD_BOOT) |
| #define MC_INIT_CMD \ |
| "mcinitcmd=mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \ |
| "mmc read 0x80e00000 0x7000 0x800;" \ |
| "env exists secureboot && " \ |
| "mmc read 0x80640000 0x3200 0x20 && " \ |
| "mmc read 0x80680000 0x3400 0x20 && " \ |
| "esbc_validate 0x80640000 && " \ |
| "esbc_validate 0x80680000 ;" \ |
| "fsl_mc start mc 0x80a00000 0x80e00000\0" \ |
| "mcmemsize=0x70000000\0" |
| #else |
| #define MC_INIT_CMD \ |
| "mcinitcmd=env exists secureboot && " \ |
| "esbc_validate 0x580640000 && " \ |
| "esbc_validate 0x580680000; " \ |
| "fsl_mc start mc 0x580a00000 0x580e00000 \0" |
| #endif |
| #endif |
| |
| /* Initial environment variables */ |
| #undef CONFIG_EXTRA_ENV_SETTINGS |
| #ifdef CONFIG_TFABOOT |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_addr=0x581000000\0" \ |
| "kernel_start=0x1000000\0" \ |
| "kernelheader_start=0x800000\0" \ |
| "scriptaddr=0x80000000\0" \ |
| "scripthdraddr=0x80080000\0" \ |
| "fdtheader_addr_r=0x80100000\0" \ |
| "kernelheader_addr_r=0x80200000\0" \ |
| "kernelheader_addr=0x580600000\0" \ |
| "kernel_addr_r=0x81000000\0" \ |
| "kernelheader_size=0x40000\0" \ |
| "fdt_addr_r=0x90000000\0" \ |
| "load_addr=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "kernel_addr_sd=0x8000\0" \ |
| "kernel_size_sd=0x14000\0" \ |
| "console=ttyAMA0,38400n8\0" \ |
| "mcmemsize=0x70000000\0" \ |
| "sd_bootcmd=echo Trying load from SD ..;" \ |
| "mmcinfo; mmc read $load_addr " \ |
| "$kernel_addr_sd $kernel_size_sd && " \ |
| "bootm $load_addr#$board\0" \ |
| QSPI_MC_INIT_CMD \ |
| BOOTENV \ |
| "boot_scripts=ls2088ardb_boot.scr\0" \ |
| "boot_script_hdr=hdr_ls2088ardb_bs.out\0" \ |
| "scan_dev_for_boot_part=" \ |
| "part list ${devtype} ${devnum} devplist; " \ |
| "env exists devplist || setenv devplist 1; " \ |
| "for distro_bootpart in ${devplist}; do " \ |
| "if fstype ${devtype} " \ |
| "${devnum}:${distro_bootpart} " \ |
| "bootfstype; then " \ |
| "run scan_dev_for_boot; " \ |
| "fi; " \ |
| "done\0" \ |
| "boot_a_script=" \ |
| "load ${devtype} ${devnum}:${distro_bootpart} " \ |
| "${scriptaddr} ${prefix}${script}; " \ |
| "env exists secureboot && load ${devtype} " \ |
| "${devnum}:${distro_bootpart} " \ |
| "${scripthdraddr} ${prefix}${boot_script_hdr} " \ |
| "&& esbc_validate ${scripthdraddr};" \ |
| "source ${scriptaddr}\0" \ |
| "qspi_bootcmd=echo Trying load from qspi..;" \ |
| "sf probe && sf read $load_addr " \ |
| "$kernel_start $kernel_size ; env exists secureboot &&" \ |
| "sf read $kernelheader_addr_r $kernelheader_start " \ |
| "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ |
| " bootm $load_addr#$board\0" \ |
| "nor_bootcmd=echo Trying load from nor..;" \ |
| "cp.b $kernel_addr $load_addr " \ |
| "$kernel_size ; env exists secureboot && " \ |
| "cp.b $kernelheader_addr $kernelheader_addr_r " \ |
| "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ |
| "bootm $load_addr#$board\0" |
| #else |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_addr=0x581000000\0" \ |
| "kernel_start=0x1000000\0" \ |
| "kernelheader_start=0x600000\0" \ |
| "scriptaddr=0x80000000\0" \ |
| "scripthdraddr=0x80080000\0" \ |
| "fdtheader_addr_r=0x80100000\0" \ |
| "kernelheader_addr_r=0x80200000\0" \ |
| "kernelheader_addr=0x580600000\0" \ |
| "kernel_addr_r=0x81000000\0" \ |
| "kernelheader_size=0x40000\0" \ |
| "fdt_addr_r=0x90000000\0" \ |
| "load_addr=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "kernel_addr_sd=0x8000\0" \ |
| "kernel_size_sd=0x14000\0" \ |
| "console=ttyAMA0,38400n8\0" \ |
| "mcmemsize=0x70000000\0" \ |
| "sd_bootcmd=echo Trying load from SD ..;" \ |
| "mmcinfo; mmc read $load_addr " \ |
| "$kernel_addr_sd $kernel_size_sd && " \ |
| "bootm $load_addr#$board\0" \ |
| MC_INIT_CMD \ |
| BOOTENV \ |
| "boot_scripts=ls2088ardb_boot.scr\0" \ |
| "boot_script_hdr=hdr_ls2088ardb_bs.out\0" \ |
| "scan_dev_for_boot_part=" \ |
| "part list ${devtype} ${devnum} devplist; " \ |
| "env exists devplist || setenv devplist 1; " \ |
| "for distro_bootpart in ${devplist}; do " \ |
| "if fstype ${devtype} " \ |
| "${devnum}:${distro_bootpart} " \ |
| "bootfstype; then " \ |
| "run scan_dev_for_boot; " \ |
| "fi; " \ |
| "done\0" \ |
| "boot_a_script=" \ |
| "load ${devtype} ${devnum}:${distro_bootpart} " \ |
| "${scriptaddr} ${prefix}${script}; " \ |
| "env exists secureboot && load ${devtype} " \ |
| "${devnum}:${distro_bootpart} " \ |
| "${scripthdraddr} ${prefix}${boot_script_hdr}; " \ |
| "env exists secureboot " \ |
| "&& esbc_validate ${scripthdraddr};" \ |
| "source ${scriptaddr}\0" \ |
| "qspi_bootcmd=echo Trying load from qspi..;" \ |
| "sf probe && sf read $load_addr " \ |
| "$kernel_start $kernel_size ; env exists secureboot &&" \ |
| "sf read $kernelheader_addr_r $kernelheader_start " \ |
| "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ |
| " bootm $load_addr#$board\0" \ |
| "nor_bootcmd=echo Trying load from nor..;" \ |
| "cp.b $kernel_addr $load_addr " \ |
| "$kernel_size ; env exists secureboot && " \ |
| "cp.b $kernelheader_addr $kernelheader_addr_r " \ |
| "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ |
| "bootm $load_addr#$board\0" |
| #endif |
| |
| #ifdef CONFIG_TFABOOT |
| #define QSPI_NOR_BOOTCOMMAND \ |
| "sf probe 0:0; " \ |
| "sf read 0x806c0000 0x6c0000 0x40000; " \ |
| "env exists mcinitcmd && env exists secureboot "\ |
| "&& esbc_validate 0x806c0000; " \ |
| "sf read 0x80d00000 0xd00000 0x100000; " \ |
| "env exists mcinitcmd && " \ |
| "fsl_mc lazyapply dpl 0x80d00000; " \ |
| "run distro_bootcmd;run qspi_bootcmd; " \ |
| "env exists secureboot && esbc_halt;" |
| |
| /* Try to boot an on-SD kernel first, then do normal distro boot */ |
| #define SD_BOOTCOMMAND \ |
| "env exists mcinitcmd && env exists secureboot "\ |
| "&& mmcinfo && mmc read $load_addr 0x3600 0x800 " \ |
| "&& esbc_validate $load_addr; " \ |
| "env exists mcinitcmd && run mcinitcmd " \ |
| "&& mmc read 0x80d00000 0x6800 0x800 " \ |
| "&& fsl_mc lazyapply dpl 0x80d00000; " \ |
| "run distro_bootcmd;run sd_bootcmd; " \ |
| "env exists secureboot && esbc_halt;" |
| |
| /* Try to boot an on-NOR kernel first, then do normal distro boot */ |
| #define IFC_NOR_BOOTCOMMAND \ |
| "env exists mcinitcmd && env exists secureboot "\ |
| "&& esbc_validate 0x5806C0000; env exists mcinitcmd "\ |
| "&& fsl_mc lazyapply dpl 0x580d00000;" \ |
| "run distro_bootcmd;run nor_bootcmd; " \ |
| "env exists secureboot && esbc_halt;" |
| #else |
| #ifdef CONFIG_QSPI_BOOT |
| /* Try to boot an on-QSPI kernel first, then do normal distro boot */ |
| #elif defined(CONFIG_SD_BOOT) |
| /* Try to boot an on-SD kernel first, then do normal distro boot */ |
| #else |
| /* Try to boot an on-NOR kernel first, then do normal distro boot */ |
| #endif |
| #endif |
| |
| /* MAC/PHY configuration */ |
| #define CORTINA_PHY_ADDR1 0x10 |
| #define CORTINA_PHY_ADDR2 0x11 |
| #define CORTINA_PHY_ADDR3 0x12 |
| #define CORTINA_PHY_ADDR4 0x13 |
| #define AQ_PHY_ADDR1 0x00 |
| #define AQ_PHY_ADDR2 0x01 |
| #define AQ_PHY_ADDR3 0x02 |
| #define AQ_PHY_ADDR4 0x03 |
| #define AQR405_IRQ_MASK 0x36 |
| |
| #include <asm/fsl_secure_boot.h> |
| |
| #endif /* __LS2_RDB_H */ |