blob: efd29686025a7b6de612f8490cb6032c32aa323b [file] [log] [blame]
/*
* Copyright (C) 2012 Altera Corporation <www.altera.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_SOCFPGA_COMMON_H__
#define __CONFIG_SOCFPGA_COMMON_H__
/* Virtual target or real hardware */
#undef CONFIG_SOCFPGA_VIRTUAL_TARGET
#define CONFIG_SYS_THUMB_BUILD
/*
* High level configuration
*/
#define CONFIG_DISPLAY_BOARDINFO_LATE
#define CONFIG_ARCH_MISC_INIT
#define CONFIG_ARCH_EARLY_INIT_R
#define CONFIG_SYS_NO_FLASH
#define CONFIG_CLOCKS
#define CONFIG_CRC32_VERIFY
#define CONFIG_SYS_BOOTMAPSZ (64 * 1024 * 1024)
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
/* add target to build it automatically upon "make" */
#define CONFIG_BUILD_TARGET "u-boot-with-spl.sfp"
/*
* Memory configurations
*/
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x0
#define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024)
#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE
#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
#define CONFIG_SYS_INIT_RAM_SIZE 0x10000
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
#define CONFIG_SYS_TEXT_BASE 0x08000040
#else
#define CONFIG_SYS_TEXT_BASE 0x01000040
#endif
/*
* U-Boot general configurations
*/
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
#define CONFIG_SYS_PBSIZE \
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
/* Print buffer size */
#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* Boot argument buffer size */
#define CONFIG_AUTO_COMPLETE /* Command auto complete */
#define CONFIG_CMDLINE_EDITING /* Command history etc */
#ifndef CONFIG_SYS_HOSTNAME
#define CONFIG_SYS_HOSTNAME CONFIG_SYS_BOARD
#endif
/*
* Cache
*/
#define CONFIG_SYS_L2_PL310
#define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS
/*
* SDRAM controller
*/
#define CONFIG_ALTERA_SDRAM
/*
* EPCS/EPCQx1 Serial Flash Controller
*/
#ifdef CONFIG_ALTERA_SPI
#define CONFIG_SF_DEFAULT_SPEED 30000000
/*
* The base address is configurable in QSys, each board must specify the
* base address based on it's particular FPGA configuration. Please note
* that the address here is incremented by 0x400 from the Base address
* selected in QSys, since the SPI registers are at offset +0x400.
* #define CONFIG_SYS_SPI_BASE 0xff240400
*/
#endif
/*
* Ethernet on SoC (EMAC)
*/
#if defined(CONFIG_CMD_NET) && !defined(CONFIG_SOCFPGA_VIRTUAL_TARGET)
#define CONFIG_DW_ALTDESCRIPTOR
#define CONFIG_MII
#define CONFIG_AUTONEG_TIMEOUT (15 * CONFIG_SYS_HZ)
#define CONFIG_PHY_GIGE
#endif
/*
* FPGA Driver
*/
#ifdef CONFIG_CMD_FPGA
#define CONFIG_FPGA
#define CONFIG_FPGA_ALTERA
#define CONFIG_FPGA_SOCFPGA
#define CONFIG_FPGA_COUNT 1
#endif
/*
* L4 OSC1 Timer 0
*/
/* This timer uses eosc1, whose clock frequency is fixed at any condition. */
#define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS
#define CONFIG_SYS_TIMER_COUNTS_DOWN
#define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4)
#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
#define CONFIG_SYS_TIMER_RATE 2400000
#else
#define CONFIG_SYS_TIMER_RATE 25000000
#endif
/*
* L4 Watchdog
*/
#ifdef CONFIG_HW_WATCHDOG
#define CONFIG_DESIGNWARE_WATCHDOG
#define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS
#define CONFIG_DW_WDT_CLOCK_KHZ 25000
#define CONFIG_HW_WATCHDOG_TIMEOUT_MS 30000
#endif
/*
* MMC Driver
*/
#ifdef CONFIG_CMD_MMC
#define CONFIG_MMC
#define CONFIG_BOUNCE_BUFFER
#define CONFIG_GENERIC_MMC
#define CONFIG_DWMMC
#define CONFIG_SOCFPGA_DWMMC
#define CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH 1024
/* FIXME */
/* using smaller max blk cnt to avoid flooding the limited stack we have */
#define CONFIG_SYS_MMC_MAX_BLK_COUNT 256 /* FIXME -- SPL only? */
#endif
/*
* NAND Support
*/
#ifdef CONFIG_NAND_DENALI
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_MAX_CHIPS 1
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_NAND_DENALI_ECC_SIZE 512
#define CONFIG_SYS_NAND_REGS_BASE SOCFPGA_NANDREGS_ADDRESS
#define CONFIG_SYS_NAND_DATA_BASE SOCFPGA_NANDDATA_ADDRESS
#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_DATA_BASE + 0x10)
#endif
/*
* I2C support
*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_BUS_MAX 4
#define CONFIG_SYS_I2C_BASE SOCFPGA_I2C0_ADDRESS
#define CONFIG_SYS_I2C_BASE1 SOCFPGA_I2C1_ADDRESS
#define CONFIG_SYS_I2C_BASE2 SOCFPGA_I2C2_ADDRESS
#define CONFIG_SYS_I2C_BASE3 SOCFPGA_I2C3_ADDRESS
/* Using standard mode which the speed up to 100Kb/s */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SPEED1 100000
#define CONFIG_SYS_I2C_SPEED2 100000
#define CONFIG_SYS_I2C_SPEED3 100000
/* Address of device when used as slave */
#define CONFIG_SYS_I2C_SLAVE 0x02
#define CONFIG_SYS_I2C_SLAVE1 0x02
#define CONFIG_SYS_I2C_SLAVE2 0x02
#define CONFIG_SYS_I2C_SLAVE3 0x02
#ifndef __ASSEMBLY__
/* Clock supplied to I2C controller in unit of MHz */
unsigned int cm_get_l4_sp_clk_hz(void);
#define IC_CLK (cm_get_l4_sp_clk_hz() / 1000000)
#endif
/*
* QSPI support
*/
/* Enable multiple SPI NOR flash manufacturers */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SPI_FLASH_MTD
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define MTDIDS_DEFAULT "nor0=ff705000.spi.0"
#endif
/* QSPI reference clock */
#ifndef __ASSEMBLY__
unsigned int cm_get_qspi_controller_clk_hz(void);
#define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz()
#endif
#define CONFIG_CQSPI_DECODER 0
/*
* Designware SPI support
*/
/*
* Serial Driver
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE -4
#define CONFIG_SYS_NS16550_COM1 SOCFPGA_UART0_ADDRESS
#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
#define CONFIG_SYS_NS16550_CLK 1000000
#else
#define CONFIG_SYS_NS16550_CLK 100000000
#endif
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
/*
* USB
*/
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_DWC2
#endif
/*
* USB Gadget (DFU, UMS)
*/
#if defined(CONFIG_CMD_DFU) || defined(CONFIG_CMD_USB_MASS_STORAGE)
#define CONFIG_USB_FUNCTION_MASS_STORAGE
#define CONFIG_SYS_DFU_DATA_BUF_SIZE (32 * 1024 * 1024)
#define DFU_DEFAULT_POLL_TIMEOUT 300
/* USB IDs */
#define CONFIG_G_DNL_UMS_VENDOR_NUM 0x0525
#define CONFIG_G_DNL_UMS_PRODUCT_NUM 0xA4A5
#endif
/*
* U-Boot environment
*/
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
#if !defined(CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE 4096
#endif
/* Environment for SDMMC boot */
#if defined(CONFIG_ENV_IS_IN_MMC) && !defined(CONFIG_ENV_OFFSET)
#define CONFIG_SYS_MMC_ENV_DEV 0 /* device 0 */
#define CONFIG_ENV_OFFSET 512 /* just after the MBR */
#endif
/* Environment for QSPI boot */
#if defined(CONFIG_ENV_IS_IN_SPI_FLASH) && !defined(CONFIG_ENV_OFFSET)
#define CONFIG_ENV_OFFSET 0x00100000
#define CONFIG_ENV_SECT_SIZE (64 * 1024)
#endif
/*
* mtd partitioning for serial NOR flash
*
* device nor0 <ff705000.spi.0>, # parts = 6
* #: name size offset mask_flags
* 0: u-boot 0x00100000 0x00000000 0
* 1: env1 0x00040000 0x00100000 0
* 2: env2 0x00040000 0x00140000 0
* 3: UBI 0x03e80000 0x00180000 0
* 4: boot 0x00e80000 0x00180000 0
* 5: rootfs 0x01000000 0x01000000 0
*
*/
#if defined(CONFIG_CMD_SF) && !defined(MTDPARTS_DEFAULT)
#define MTDPARTS_DEFAULT "mtdparts=ff705000.spi.0:"\
"1m(u-boot)," \
"256k(env1)," \
"256k(env2)," \
"14848k(boot)," \
"16m(rootfs)," \
"-@1536k(UBI)\0"
#endif
/* UBI and UBIFS support */
#if defined(CONFIG_CMD_SF) || defined(CONFIG_CMD_NAND)
#define CONFIG_CMD_UBIFS
#define CONFIG_RBTREE
#define CONFIG_LZO
#endif
/*
* SPL
*
* SRAM Memory layout:
*
* 0xFFFF_0000 ...... Start of SRAM
* 0xFFFF_xxxx ...... Top of stack (grows down)
* 0xFFFF_yyyy ...... Malloc area
* 0xFFFF_zzzz ...... Global Data
* 0xFFFF_FF00 ...... End of SRAM
*/
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_RAM_DEVICE
#define CONFIG_SPL_TEXT_BASE CONFIG_SYS_INIT_RAM_ADDR
#define CONFIG_SPL_MAX_SIZE (64 * 1024)
/* SPL SDMMC boot support */
#ifdef CONFIG_SPL_MMC_SUPPORT
#if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 2
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img"
#else
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200 /* offset 512 sect (256k) */
#endif
#endif
/* SPL QSPI boot support */
#ifdef CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x40000
#endif
/* SPL NAND boot support */
#ifdef CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#endif
/*
* Stack setup
*/
#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
#endif /* __CONFIG_SOCFPGA_COMMON_H__ */