| # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/usb/ci-hdrc-usb2.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: USB2 ChipIdea USB controller |
| |
| maintainers: |
| - Xu Yang <xu.yang_2@nxp.com> |
| - Peng Fan <peng.fan@nxp.com> |
| |
| properties: |
| compatible: |
| oneOf: |
| - enum: |
| - chipidea,usb2 |
| - fsl,imx27-usb |
| - lsi,zevio-usb |
| - nuvoton,npcm750-udc |
| - nvidia,tegra20-ehci |
| - nvidia,tegra20-udc |
| - nvidia,tegra30-ehci |
| - nvidia,tegra30-udc |
| - nvidia,tegra114-udc |
| - nvidia,tegra124-udc |
| - qcom,ci-hdrc |
| - items: |
| - enum: |
| - nvidia,tegra114-ehci |
| - nvidia,tegra124-ehci |
| - nvidia,tegra210-ehci |
| - const: nvidia,tegra30-ehci |
| - items: |
| - enum: |
| - fsl,imx23-usb |
| - fsl,imx25-usb |
| - fsl,imx28-usb |
| - fsl,imx35-usb |
| - fsl,imx50-usb |
| - fsl,imx51-usb |
| - fsl,imx53-usb |
| - fsl,imx6q-usb |
| - fsl,imx6sl-usb |
| - fsl,imx6sx-usb |
| - fsl,imx6ul-usb |
| - fsl,imx7d-usb |
| - fsl,vf610-usb |
| - const: fsl,imx27-usb |
| - items: |
| - enum: |
| - fsl,imx8dxl-usb |
| - fsl,imx8ulp-usb |
| - const: fsl,imx7ulp-usb |
| - const: fsl,imx6ul-usb |
| - items: |
| - enum: |
| - fsl,imx8mm-usb |
| - fsl,imx8mn-usb |
| - const: fsl,imx7d-usb |
| - const: fsl,imx27-usb |
| - items: |
| - enum: |
| - fsl,imx6sll-usb |
| - fsl,imx7ulp-usb |
| - const: fsl,imx6ul-usb |
| - const: fsl,imx27-usb |
| - items: |
| - const: xlnx,zynq-usb-2.20a |
| - const: chipidea,usb2 |
| - items: |
| - enum: |
| - nuvoton,npcm845-udc |
| - const: nuvoton,npcm750-udc |
| |
| reg: |
| minItems: 1 |
| maxItems: 2 |
| |
| interrupts: |
| minItems: 1 |
| maxItems: 2 |
| |
| clocks: |
| minItems: 1 |
| maxItems: 3 |
| |
| clock-names: |
| minItems: 1 |
| maxItems: 3 |
| |
| dr_mode: true |
| |
| power-domains: |
| maxItems: 1 |
| |
| resets: |
| maxItems: 1 |
| |
| reset-names: |
| maxItems: 1 |
| |
| "#reset-cells": |
| const: 1 |
| |
| phy_type: true |
| |
| itc-setting: |
| description: |
| interrupt threshold control register control, the setting should be |
| aligned with ITC bits at register USBCMD. |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| |
| ahb-burst-config: |
| description: |
| it is vendor dependent, the required value should be aligned with |
| AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This property is |
| used to change AHB burst configuration, check the chipidea spec for |
| meaning of each value. If this property is not existed, it will use |
| the reset value. |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0x0 |
| maximum: 0x7 |
| |
| tx-burst-size-dword: |
| description: |
| it is vendor dependent, the tx burst size in dword (4 bytes), This |
| register represents the maximum length of a the burst in 32-bit |
| words while moving data from system memory to the USB bus, the value |
| of this property will only take effect if property "ahb-burst-config" |
| is set to 0, if this property is missing the reset default of the |
| hardware implementation will be used. |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0x0 |
| maximum: 0x20 |
| |
| rx-burst-size-dword: |
| description: |
| it is vendor dependent, the rx burst size in dword (4 bytes), This |
| register represents the maximum length of a the burst in 32-bit words |
| while moving data from the USB bus to system memory, the value of |
| this property will only take effect if property "ahb-burst-config" |
| is set to 0, if this property is missing the reset default of the |
| hardware implementation will be used. |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0x0 |
| maximum: 0x20 |
| |
| extcon: |
| description: |
| Phandles to external connector devices. First phandle should point |
| to external connector, which provide "USB" cable events, the second |
| should point to external connector device, which provide "USB-HOST" |
| cable events. If one of the external connector devices is not |
| required, empty <0> phandle should be specified. |
| $ref: /schemas/types.yaml#/definitions/phandle-array |
| minItems: 1 |
| items: |
| - description: vbus extcon |
| - description: id extcon |
| |
| phy-clkgate-delay-us: |
| description: |
| The delay time (us) between putting the PHY into low power mode and |
| gating the PHY clock. |
| |
| non-zero-ttctrl-ttha: |
| description: |
| After setting this property, the value of register ttctrl.ttha |
| will be 0x7f; if not, the value will be 0x0, this is the default |
| value. It needs to be very carefully for setting this property, it |
| is recommended that consult with your IC engineer before setting |
| this value. On the most of chipidea platforms, the "usage_tt" flag |
| at RTL is 0, so this property only affects siTD. |
| |
| If this property is not set, the max packet size is 1023 bytes, and |
| if the total of packet size for previous transactions are more than |
| 256 bytes, it can't accept any transactions within this frame. The |
| use case is single transaction, but higher frame rate. |
| |
| If this property is set, the max packet size is 188 bytes, it can |
| handle more transactions than above case, it can accept transactions |
| until it considers the left room size within frame is less than 188 |
| bytes, software needs to make sure it does not send more than 90% |
| maximum_periodic_data_per_frame. The use case is multiple |
| transactions, but less frame rate. |
| type: boolean |
| |
| mux-controls: |
| description: |
| The mux control for toggling host/device output of this controller. |
| It's expected that a mux state of 0 indicates device mode and a mux |
| state of 1 indicates host mode. |
| maxItems: 1 |
| |
| mux-control-names: |
| const: usb_switch |
| |
| operating-points-v2: |
| description: A phandle to the OPP table containing the performance states. |
| $ref: /schemas/types.yaml#/definitions/phandle |
| |
| pinctrl-names: |
| description: |
| Names for optional pin modes in "default", "host", "device". |
| In case of HSIC-mode, "idle" and "active" pin modes are mandatory. |
| In this case, the "idle" state needs to pull down the data and |
| strobe pin and the "active" state needs to pull up the strobe pin. |
| oneOf: |
| - items: |
| - const: idle |
| - const: active |
| - items: |
| - const: default |
| - enum: |
| - host |
| - device |
| - items: |
| - const: default |
| |
| pinctrl-0: |
| maxItems: 1 |
| |
| pinctrl-1: |
| maxItems: 1 |
| |
| phys: |
| maxItems: 1 |
| |
| phy-names: |
| const: usb-phy |
| |
| phy-select: |
| description: |
| Phandler of TCSR node with two argument that indicate register |
| offset, and phy index |
| $ref: /schemas/types.yaml#/definitions/phandle-array |
| items: |
| - description: phandle to TCSR node |
| - description: register offset |
| - description: phy index |
| |
| vbus-supply: |
| description: reference to the VBUS regulator. |
| |
| fsl,usbmisc: |
| description: |
| Phandler of non-core register device, with one argument that |
| indicate usb controller index |
| $ref: /schemas/types.yaml#/definitions/phandle-array |
| items: |
| - items: |
| - description: phandle to usbmisc node |
| - description: index of usb controller |
| |
| fsl,anatop: |
| description: phandle for the anatop node. |
| $ref: /schemas/types.yaml#/definitions/phandle |
| |
| disable-over-current: |
| type: boolean |
| description: disable over current detect |
| |
| over-current-active-low: |
| type: boolean |
| description: over current signal polarity is active low |
| |
| over-current-active-high: |
| type: boolean |
| description: |
| Over current signal polarity is active high. It's recommended to |
| specify the over current polarity. |
| |
| power-active-high: |
| type: boolean |
| description: power signal polarity is active high |
| |
| external-vbus-divider: |
| type: boolean |
| description: enables off-chip resistor divider for Vbus |
| |
| samsung,picophy-pre-emp-curr-control: |
| description: |
| HS Transmitter Pre-Emphasis Current Control. This signal controls |
| the amount of current sourced to the USB_OTG*_DP and USB_OTG*_DN |
| pins after a J-to-K or K-to-J transition. The range is from 0x0 to |
| 0x3, the default value is 0x1. Details can refer to TXPREEMPAMPTUNE0 |
| bits of USBNC_n_PHY_CFG1. |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0x0 |
| maximum: 0x3 |
| |
| samsung,picophy-dc-vol-level-adjust: |
| description: |
| HS DC Voltage Level Adjustment. Adjust the high-speed transmitter DC |
| level voltage. The range is from 0x0 to 0xf, the default value is |
| 0x3. Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1. |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0x0 |
| maximum: 0xf |
| |
| fsl,picophy-rise-fall-time-adjust: |
| description: |
| HS Transmitter Rise/Fall Time Adjustment. Adjust the rise/fall times |
| of the high-speed transmitter waveform. It has no unit. The rise/fall |
| time will be increased or decreased by a certain percentage relative |
| to design default time. (0:-10%; 1:design default; 2:+15%; 3:+20%) |
| Details can refer to TXRISETUNE0 bit of USBNC_n_PHY_CFG1. |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0 |
| maximum: 3 |
| default: 1 |
| |
| usb-phy: |
| description: phandle for the PHY device. Use "phys" instead. |
| $ref: /schemas/types.yaml#/definitions/phandle |
| deprecated: true |
| |
| fsl,usbphy: |
| description: phandle of usb phy that connects to the port. Use "phys" instead. |
| $ref: /schemas/types.yaml#/definitions/phandle |
| deprecated: true |
| |
| nvidia,phy: |
| description: phandle of usb phy that connects to the port. Use "phys" instead. |
| $ref: /schemas/types.yaml#/definitions/phandle |
| deprecated: true |
| |
| nvidia,needs-double-reset: |
| description: Indicates double reset or not. |
| type: boolean |
| deprecated: true |
| |
| port: |
| description: |
| Any connector to the data bus of this controller should be modelled |
| using the OF graph bindings specified, if the "usb-role-switch" |
| property is used. |
| $ref: /schemas/graph.yaml#/properties/port |
| |
| reset-gpios: |
| maxItems: 1 |
| |
| ulpi: |
| type: object |
| additionalProperties: false |
| patternProperties: |
| "^phy(-[0-9])?$": |
| description: The phy child node for Qcom chips. |
| type: object |
| $ref: /schemas/phy/qcom,usb-hs-phy.yaml |
| |
| dependencies: |
| port: [ usb-role-switch ] |
| mux-controls: [ mux-control-names ] |
| |
| required: |
| - compatible |
| - reg |
| - interrupts |
| |
| allOf: |
| - $ref: usb-hcd.yaml# |
| - $ref: usb-drd.yaml# |
| - if: |
| properties: |
| phy_type: |
| const: hsic |
| required: |
| - phy_type |
| then: |
| properties: |
| pinctrl-names: |
| items: |
| - const: idle |
| - const: active |
| else: |
| properties: |
| pinctrl-names: |
| minItems: 1 |
| maxItems: 2 |
| oneOf: |
| - items: |
| - const: default |
| - enum: |
| - host |
| - device |
| - items: |
| - const: default |
| - if: |
| properties: |
| compatible: |
| contains: |
| enum: |
| - chipidea,usb2 |
| - lsi,zevio-usb |
| - nuvoton,npcm750-udc |
| - nvidia,tegra20-udc |
| - nvidia,tegra30-udc |
| - nvidia,tegra114-udc |
| - nvidia,tegra124-udc |
| - qcom,ci-hdrc |
| - xlnx,zynq-usb-2.20a |
| then: |
| properties: |
| fsl,usbmisc: false |
| disable-over-current: false |
| over-current-active-low: false |
| over-current-active-high: false |
| power-active-high: false |
| external-vbus-divider: false |
| samsung,picophy-pre-emp-curr-control: false |
| samsung,picophy-dc-vol-level-adjust: false |
| |
| unevaluatedProperties: false |
| |
| examples: |
| - | |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/clock/berlin2.h> |
| |
| usb@f7ed0000 { |
| compatible = "chipidea,usb2"; |
| reg = <0xf7ed0000 0x10000>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&chip CLKID_USB0>; |
| phys = <&usb_phy0>; |
| phy-names = "usb-phy"; |
| vbus-supply = <®_usb0_vbus>; |
| itc-setting = <0x4>; /* 4 micro-frames */ |
| /* Incremental burst of unspecified length */ |
| ahb-burst-config = <0x0>; |
| tx-burst-size-dword = <0x10>; /* 64 bytes */ |
| rx-burst-size-dword = <0x10>; |
| extcon = <0>, <&usb_id>; |
| phy-clkgate-delay-us = <400>; |
| mux-controls = <&usb_switch>; |
| mux-control-names = "usb_switch"; |
| }; |
| |
| # Example for HSIC: |
| - | |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/clock/imx6qdl-clock.h> |
| |
| usb@2184400 { |
| compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; |
| reg = <0x02184400 0x200>; |
| interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_USBOH3>; |
| fsl,usbphy = <&usbphynop1>; |
| fsl,usbmisc = <&usbmisc 2>; |
| phy_type = "hsic"; |
| dr_mode = "host"; |
| ahb-burst-config = <0x0>; |
| tx-burst-size-dword = <0x10>; |
| rx-burst-size-dword = <0x10>; |
| pinctrl-names = "idle", "active"; |
| pinctrl-0 = <&pinctrl_usbh2_idle>; |
| pinctrl-1 = <&pinctrl_usbh2_active>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethernet@1 { |
| compatible = "usb424,9730"; |
| reg = <1>; |
| }; |
| }; |
| |
| ... |