| U-Boot for Khadas VIM |
| ======================= |
| |
| Khadas VIM is an Open Source DIY Box manufactured by Shenzhen Wesion |
| Technology Co., Ltd with the following specifications: |
| |
| - Amlogic S905X ARM Cortex-A53 quad-core SoC @ 1.5GHz |
| - ARM Mali 450 GPU |
| - 2GB DDR3 SDRAM |
| - 10/100 Ethernet |
| - HDMI 2.0 4K/60Hz display |
| - 40-pin GPIO header |
| - 2 x USB 2.0 Host, 1 x USB 2.0 Type-C OTG |
| - 8GB/16GBeMMC |
| - microSD |
| - SDIO Wifi Module, Bluetooth |
| - Two channels IR receiver |
| |
| Currently the u-boot port supports the following devices: |
| - serial |
| - eMMC, microSD |
| - Ethernet |
| - I2C |
| - Regulators |
| - Reset controller |
| - Clock controller |
| - USB Host |
| - ADC |
| |
| U-Boot compilation |
| ================== |
| |
| > export ARCH=arm |
| > export CROSS_COMPILE=aarch64-none-elf- |
| > make khadas-vim_defconfig |
| > make |
| |
| Image creation |
| ============== |
| |
| Amlogic doesn't provide sources for the firmware and for tools needed |
| to create the bootloader image, so it is necessary to obtain them from |
| the git tree published by the board vendor: |
| |
| > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz |
| > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz |
| > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz |
| > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz |
| > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH |
| > git clone https://github.com/khadas/u-boot -b Vim vim-u-boot |
| > cd vim-u-boot |
| > make kvim_defconfig |
| > make |
| > export FIPDIR=$PWD/fip |
| |
| Go back to mainline U-Boot source tree then : |
| > mkdir fip |
| |
| > cp $FIPDIR/gxl/bl2.bin fip/ |
| > cp $FIPDIR/gxl/acs.bin fip/ |
| > cp $FIPDIR/gxl/bl21.bin fip/ |
| > cp $FIPDIR/gxl/bl30.bin fip/ |
| > cp $FIPDIR/gxl/bl301.bin fip/ |
| > cp $FIPDIR/gxl/bl31.img fip/ |
| > cp u-boot.bin fip/bl33.bin |
| |
| > $FIPDIR/blx_fix.sh \ |
| fip/bl30.bin \ |
| fip/zero_tmp \ |
| fip/bl30_zero.bin \ |
| fip/bl301.bin \ |
| fip/bl301_zero.bin \ |
| fip/bl30_new.bin \ |
| bl30 |
| |
| > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 |
| |
| > $FIPDIR/blx_fix.sh \ |
| fip/bl2_acs.bin \ |
| fip/zero_tmp \ |
| fip/bl2_zero.bin \ |
| fip/bl21.bin \ |
| fip/bl21_zero.bin \ |
| fip/bl2_new.bin \ |
| bl2 |
| |
| > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin |
| > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img |
| > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin |
| > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig |
| > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ |
| --output fip/u-boot.bin \ |
| --bl2 fip/bl2.n.bin.sig \ |
| --bl30 fip/bl30_new.bin.enc \ |
| --bl31 fip/bl31.img.enc \ |
| --bl33 fip/bl33.bin.enc |
| |
| and then write the image to SD with: |
| |
| > DEV=/dev/your_sd_device |
| > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 |
| > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 |