blob: 027d07d1724baf858fa7e6ea194599d82686c04a [file] [log] [blame]
Konstantin Porotchkinede192d2018-10-08 16:48:52 +03001/*
2 * Copyright (C) 2018 Marvell International Ltd.
3 *
4 * SPDX-License-Identifier: BSD-3-Clause
5 * https://spdx.org/licenses
6 */
7
Konstantin Porotchkinede192d2018-10-08 16:48:52 +03008#include <errno.h>
Antonio Nino Diaze0f90632018-12-14 00:18:21 +00009
10#include <common/debug.h>
11#include <drivers/delay_timer.h>
12#include <lib/mmio.h>
13#include <lib/spinlock.h>
14
Konstantin Porotchkinede192d2018-10-08 16:48:52 +030015#include <mvebu.h>
16#include <mvebu_def.h>
Pali Rohár52c1de52021-05-14 15:52:11 +020017#include <plat_marvell.h>
Antonio Nino Diaze0f90632018-12-14 00:18:21 +000018
Konstantin Porotchkinede192d2018-10-08 16:48:52 +030019#include "phy-comphy-3700.h"
20#include "phy-comphy-common.h"
21
22/*
23 * COMPHY_INDIRECT_REG points to ahci address space but the ahci region used in
24 * Linux is up to 0x178 so none will access it from Linux in runtime
25 * concurrently.
26 */
27#define COMPHY_INDIRECT_REG (MVEBU_REGS_BASE + 0xE0178)
28
29/* The USB3_GBE1_PHY range is above USB3 registers used in dts */
30#define USB3_GBE1_PHY (MVEBU_REGS_BASE + 0x5C000)
31#define COMPHY_SD_ADDR (MVEBU_REGS_BASE + 0x1F000)
32
Konstantin Porotchkinede192d2018-10-08 16:48:52 +030033struct sgmii_phy_init_data_fix {
34 uint16_t addr;
35 uint16_t value;
36};
37
38/* Changes to 40M1G25 mode data required for running 40M3G125 init mode */
39static struct sgmii_phy_init_data_fix sgmii_phy_init_fix[] = {
40 {0x005, 0x07CC}, {0x015, 0x0000}, {0x01B, 0x0000}, {0x01D, 0x0000},
41 {0x01E, 0x0000}, {0x01F, 0x0000}, {0x020, 0x0000}, {0x021, 0x0030},
42 {0x026, 0x0888}, {0x04D, 0x0152}, {0x04F, 0xA020}, {0x050, 0x07CC},
43 {0x053, 0xE9CA}, {0x055, 0xBD97}, {0x071, 0x3015}, {0x076, 0x03AA},
44 {0x07C, 0x0FDF}, {0x0C2, 0x3030}, {0x0C3, 0x8000}, {0x0E2, 0x5550},
45 {0x0E3, 0x12A4}, {0x0E4, 0x7D00}, {0x0E6, 0x0C83}, {0x101, 0xFCC0},
46 {0x104, 0x0C10}
47};
48
49/* 40M1G25 mode init data */
50static uint16_t sgmii_phy_init[512] = {
51 /* 0 1 2 3 4 5 6 7 */
52 /*-----------------------------------------------------------*/
53 /* 8 9 A B C D E F */
54 0x3110, 0xFD83, 0x6430, 0x412F, 0x82C0, 0x06FA, 0x4500, 0x6D26, /* 00 */
55 0xAFC0, 0x8000, 0xC000, 0x0000, 0x2000, 0x49CC, 0x0BC9, 0x2A52, /* 08 */
56 0x0BD2, 0x0CDE, 0x13D2, 0x0CE8, 0x1149, 0x10E0, 0x0000, 0x0000, /* 10 */
57 0x0000, 0x0000, 0x0000, 0x0001, 0x0000, 0x4134, 0x0D2D, 0xFFFF, /* 18 */
58 0xFFE0, 0x4030, 0x1016, 0x0030, 0x0000, 0x0800, 0x0866, 0x0000, /* 20 */
59 0x0000, 0x0000, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, /* 28 */
60 0xFFFF, 0xFFFF, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* 30 */
61 0x0000, 0x0000, 0x000F, 0x6A62, 0x1988, 0x3100, 0x3100, 0x3100, /* 38 */
62 0x3100, 0xA708, 0x2430, 0x0830, 0x1030, 0x4610, 0xFF00, 0xFF00, /* 40 */
63 0x0060, 0x1000, 0x0400, 0x0040, 0x00F0, 0x0155, 0x1100, 0xA02A, /* 48 */
64 0x06FA, 0x0080, 0xB008, 0xE3ED, 0x5002, 0xB592, 0x7A80, 0x0001, /* 50 */
65 0x020A, 0x8820, 0x6014, 0x8054, 0xACAA, 0xFC88, 0x2A02, 0x45CF, /* 58 */
66 0x000F, 0x1817, 0x2860, 0x064F, 0x0000, 0x0204, 0x1800, 0x6000, /* 60 */
67 0x810F, 0x4F23, 0x4000, 0x4498, 0x0850, 0x0000, 0x000E, 0x1002, /* 68 */
68 0x9D3A, 0x3009, 0xD066, 0x0491, 0x0001, 0x6AB0, 0x0399, 0x3780, /* 70 */
69 0x0040, 0x5AC0, 0x4A80, 0x0000, 0x01DF, 0x0000, 0x0007, 0x0000, /* 78 */
70 0x2D54, 0x00A1, 0x4000, 0x0100, 0xA20A, 0x0000, 0x0000, 0x0000, /* 80 */
71 0x0000, 0x0000, 0x0000, 0x7400, 0x0E81, 0x1000, 0x1242, 0x0210, /* 88 */
72 0x80DF, 0x0F1F, 0x2F3F, 0x4F5F, 0x6F7F, 0x0F1F, 0x2F3F, 0x4F5F, /* 90 */
73 0x6F7F, 0x4BAD, 0x0000, 0x0000, 0x0800, 0x0000, 0x2400, 0xB651, /* 98 */
74 0xC9E0, 0x4247, 0x0A24, 0x0000, 0xAF19, 0x1004, 0x0000, 0x0000, /* A0 */
75 0x0000, 0x0013, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* A8 */
76 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* B0 */
77 0x0000, 0x0000, 0x0000, 0x0060, 0x0000, 0x0000, 0x0000, 0x0000, /* B8 */
78 0x0000, 0x0000, 0x3010, 0xFA00, 0x0000, 0x0000, 0x0000, 0x0003, /* C0 */
79 0x1618, 0x8200, 0x8000, 0x0400, 0x050F, 0x0000, 0x0000, 0x0000, /* C8 */
80 0x4C93, 0x0000, 0x1000, 0x1120, 0x0010, 0x1242, 0x1242, 0x1E00, /* D0 */
81 0x0000, 0x0000, 0x0000, 0x00F8, 0x0000, 0x0041, 0x0800, 0x0000, /* D8 */
82 0x82A0, 0x572E, 0x2490, 0x14A9, 0x4E00, 0x0000, 0x0803, 0x0541, /* E0 */
83 0x0C15, 0x0000, 0x0000, 0x0400, 0x2626, 0x0000, 0x0000, 0x4200, /* E8 */
84 0x0000, 0xAA55, 0x1020, 0x0000, 0x0000, 0x5010, 0x0000, 0x0000, /* F0 */
85 0x0000, 0x0000, 0x5000, 0x0000, 0x0000, 0x0000, 0x02F2, 0x0000, /* F8 */
86 0x101F, 0xFDC0, 0x4000, 0x8010, 0x0110, 0x0006, 0x0000, 0x0000, /*100 */
87 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*108 */
88 0x04CF, 0x0000, 0x04CF, 0x0000, 0x04CF, 0x0000, 0x04C6, 0x0000, /*110 */
89 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*118 */
90 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*120 */
91 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*128 */
92 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*130 */
93 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*138 */
94 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*140 */
95 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*148 */
96 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*150 */
97 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*158 */
98 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*160 */
99 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*168 */
100 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*170 */
101 0x0000, 0x0000, 0x0000, 0x00F0, 0x08A2, 0x3112, 0x0A14, 0x0000, /*178 */
102 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*180 */
103 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*188 */
104 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*190 */
105 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*198 */
106 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1A0 */
107 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1A8 */
108 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1B0 */
109 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1B8 */
110 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1C0 */
111 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1C8 */
112 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1D0 */
113 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1D8 */
114 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1E0 */
115 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1E8 */
116 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1F0 */
117 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 /*1F8 */
118};
119
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300120/* PHY selector configures with corresponding modes */
121static void mvebu_a3700_comphy_set_phy_selector(uint8_t comphy_index,
122 uint32_t comphy_mode)
123{
124 uint32_t reg;
125 int mode = COMPHY_GET_MODE(comphy_mode);
126
127 reg = mmio_read_32(MVEBU_COMPHY_REG_BASE + COMPHY_SELECTOR_PHY_REG);
128 switch (mode) {
129 case (COMPHY_SATA_MODE):
130 /* SATA must be in Lane2 */
131 if (comphy_index == COMPHY_LANE2)
132 reg &= ~COMPHY_SELECTOR_USB3_PHY_SEL_BIT;
133 else
134 goto error;
135 break;
136
137 case (COMPHY_SGMII_MODE):
Pali Rohár51974d22021-08-27 11:16:43 +0200138 case (COMPHY_2500BASEX_MODE):
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300139 if (comphy_index == COMPHY_LANE0)
140 reg &= ~COMPHY_SELECTOR_USB3_GBE1_SEL_BIT;
141 else if (comphy_index == COMPHY_LANE1)
142 reg &= ~COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT;
143 else
144 goto error;
145 break;
146
147 case (COMPHY_USB3H_MODE):
148 case (COMPHY_USB3D_MODE):
149 case (COMPHY_USB3_MODE):
150 if (comphy_index == COMPHY_LANE2)
151 reg |= COMPHY_SELECTOR_USB3_PHY_SEL_BIT;
152 else if (comphy_index == COMPHY_LANE0)
153 reg |= COMPHY_SELECTOR_USB3_GBE1_SEL_BIT;
154 else
155 goto error;
156 break;
157
158 case (COMPHY_PCIE_MODE):
159 /* PCIE must be in Lane1 */
160 if (comphy_index == COMPHY_LANE1)
161 reg |= COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT;
162 else
163 goto error;
164 break;
165
166 default:
167 goto error;
168 }
169
170 mmio_write_32(MVEBU_COMPHY_REG_BASE + COMPHY_SELECTOR_PHY_REG, reg);
171 return;
172error:
173 ERROR("COMPHY[%d] mode[%d] is invalid\n", comphy_index, mode);
174}
175
Marek Behún4f94cbc2019-11-05 15:21:54 +0100176/*
177 * This is something like the inverse of the previous function: for given
178 * lane it returns COMPHY_*_MODE.
179 *
180 * It is useful when powering the phy off.
181 *
182 * This function returns COMPHY_USB3_MODE even if the phy was configured
183 * with COMPHY_USB3D_MODE or COMPHY_USB3H_MODE. (The usb3 phy initialization
184 * code does not differentiate between these modes.)
185 * Also it returns COMPHY_SGMII_MODE even if the phy was configures with
Pali Rohár51974d22021-08-27 11:16:43 +0200186 * COMPHY_2500BASEX_MODE. (The sgmii phy initialization code does differentiate
Marek Behún4f94cbc2019-11-05 15:21:54 +0100187 * between these modes, but it is irrelevant when powering the phy off.)
188 */
189static int mvebu_a3700_comphy_get_mode(uint8_t comphy_index)
190{
191 uint32_t reg;
192
193 reg = mmio_read_32(MVEBU_COMPHY_REG_BASE + COMPHY_SELECTOR_PHY_REG);
194 switch (comphy_index) {
195 case COMPHY_LANE0:
196 if ((reg & COMPHY_SELECTOR_USB3_GBE1_SEL_BIT) != 0)
197 return COMPHY_USB3_MODE;
198 else
199 return COMPHY_SGMII_MODE;
200 case COMPHY_LANE1:
201 if ((reg & COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT) != 0)
202 return COMPHY_PCIE_MODE;
203 else
204 return COMPHY_SGMII_MODE;
205 case COMPHY_LANE2:
206 if ((reg & COMPHY_SELECTOR_USB3_PHY_SEL_BIT) != 0)
207 return COMPHY_USB3_MODE;
208 else
209 return COMPHY_SATA_MODE;
210 }
211
212 return COMPHY_UNUSED;
213}
214
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300215/* It is only used for SATA and USB3 on comphy lane2. */
216static void comphy_set_indirect(uintptr_t addr, uint32_t offset, uint16_t data,
217 uint16_t mask, int mode)
218{
219 /*
220 * When Lane 2 PHY is for USB3, access the PHY registers
221 * through indirect Address and Data registers:
222 * INDIR_ACC_PHY_ADDR (RD00E0178h [31:0]),
223 * INDIR_ACC_PHY_DATA (RD00E017Ch [31:0]),
224 * within the SATA Host Controller registers, Lane 2 base register
225 * offset is 0x200
226 */
227 if (mode == COMPHY_UNUSED)
228 return;
229
230 if (mode == COMPHY_SATA_MODE)
231 mmio_write_32(addr + COMPHY_LANE2_INDIR_ADDR_OFFSET, offset);
232 else
233 mmio_write_32(addr + COMPHY_LANE2_INDIR_ADDR_OFFSET,
234 offset + USB3PHY_LANE2_REG_BASE_OFFSET);
235
236 reg_set(addr + COMPHY_LANE2_INDIR_DATA_OFFSET, data, mask);
237}
238
239/* It is only used USB3 direct access not on comphy lane2. */
240static void comphy_usb3_set_direct(uintptr_t addr, uint32_t reg_offset,
241 uint16_t data, uint16_t mask, int mode)
242{
243 reg_set16((reg_offset * PHY_SHFT(USB3) + addr), data, mask);
244}
245
246static void comphy_sgmii_phy_init(uint32_t comphy_index, uint32_t mode,
247 uintptr_t sd_ip_addr)
248{
249 const int fix_arr_sz = ARRAY_SIZE(sgmii_phy_init_fix);
250 int addr, fix_idx;
251 uint16_t val;
252
253 fix_idx = 0;
254 for (addr = 0; addr < 512; addr++) {
255 /*
256 * All PHY register values are defined in full for 3.125Gbps
257 * SERDES speed. The values required for 1.25 Gbps are almost
258 * the same and only few registers should be "fixed" in
259 * comparison to 3.125 Gbps values. These register values are
260 * stored in "sgmii_phy_init_fix" array.
261 */
262 if ((mode != COMPHY_SGMII_MODE) &&
263 (sgmii_phy_init_fix[fix_idx].addr == addr)) {
264 /* Use new value */
265 val = sgmii_phy_init_fix[fix_idx].value;
266 if (fix_idx < fix_arr_sz)
267 fix_idx++;
268 } else {
269 val = sgmii_phy_init[addr];
270 }
271
272 reg_set16(SGMIIPHY_ADDR(addr, sd_ip_addr), val, 0xFFFF);
273 }
274}
275
276static int mvebu_a3700_comphy_sata_power_on(uint8_t comphy_index,
277 uint32_t comphy_mode)
278{
279 int ret = 0;
280 uint32_t offset, data = 0, ref_clk;
281 uintptr_t comphy_indir_regs = COMPHY_INDIRECT_REG;
282 int mode = COMPHY_GET_MODE(comphy_mode);
283 int invert = COMPHY_GET_POLARITY_INVERT(comphy_mode);
284
285 debug_enter();
286
287 /* Configure phy selector for SATA */
288 mvebu_a3700_comphy_set_phy_selector(comphy_index, comphy_mode);
289
290 /* Clear phy isolation mode to make it work in normal mode */
291 offset = COMPHY_ISOLATION_CTRL_REG + SATAPHY_LANE2_REG_BASE_OFFSET;
292 comphy_set_indirect(comphy_indir_regs, offset, 0, PHY_ISOLATE_MODE,
293 mode);
294
295 /* 0. Check the Polarity invert bits */
296 if (invert & COMPHY_POLARITY_TXD_INVERT)
297 data |= TXD_INVERT_BIT;
298 if (invert & COMPHY_POLARITY_RXD_INVERT)
299 data |= RXD_INVERT_BIT;
300
301 offset = COMPHY_SYNC_PATTERN_REG + SATAPHY_LANE2_REG_BASE_OFFSET;
302 comphy_set_indirect(comphy_indir_regs, offset, data, TXD_INVERT_BIT |
303 RXD_INVERT_BIT, mode);
304
305 /* 1. Select 40-bit data width width */
306 offset = COMPHY_LOOPBACK_REG0 + SATAPHY_LANE2_REG_BASE_OFFSET;
307 comphy_set_indirect(comphy_indir_regs, offset, DATA_WIDTH_40BIT,
308 SEL_DATA_WIDTH_MASK, mode);
309
310 /* 2. Select reference clock(25M) and PHY mode (SATA) */
311 offset = COMPHY_POWER_PLL_CTRL + SATAPHY_LANE2_REG_BASE_OFFSET;
312 if (get_ref_clk() == 40)
313 ref_clk = REF_CLOCK_SPEED_40M;
314 else
315 ref_clk = REF_CLOCK_SPEED_25M;
316
317 comphy_set_indirect(comphy_indir_regs, offset, ref_clk | PHY_MODE_SATA,
318 REF_FREF_SEL_MASK | PHY_MODE_MASK, mode);
319
320 /* 3. Use maximum PLL rate (no power save) */
321 offset = COMPHY_KVCO_CAL_CTRL + SATAPHY_LANE2_REG_BASE_OFFSET;
322 comphy_set_indirect(comphy_indir_regs, offset, USE_MAX_PLL_RATE_BIT,
323 USE_MAX_PLL_RATE_BIT, mode);
324
325 /* 4. Reset reserved bit */
326 comphy_set_indirect(comphy_indir_regs, COMPHY_RESERVED_REG, 0,
327 PHYCTRL_FRM_PIN_BIT, mode);
328
329 /* 5. Set vendor-specific configuration (It is done in sata driver) */
330 /* XXX: in U-Boot below sequence was executed in this place, in Linux
331 * not. Now it is done only in U-Boot before this comphy
332 * initialization - tests shows that it works ok, but in case of any
333 * future problem it is left for reference.
334 * reg_set(MVEBU_REGS_BASE + 0xe00a0, 0, 0xffffffff);
335 * reg_set(MVEBU_REGS_BASE + 0xe00a4, BIT(6), BIT(6));
336 */
337
338 /* Wait for > 55 us to allow PLL be enabled */
339 udelay(PLL_SET_DELAY_US);
340
341 /* Polling status */
342 mmio_write_32(comphy_indir_regs + COMPHY_LANE2_INDIR_ADDR_OFFSET,
343 COMPHY_LOOPBACK_REG0 + SATAPHY_LANE2_REG_BASE_OFFSET);
344
345 ret = polling_with_timeout(comphy_indir_regs +
346 COMPHY_LANE2_INDIR_DATA_OFFSET,
347 PLL_READY_TX_BIT, PLL_READY_TX_BIT,
348 COMPHY_PLL_TIMEOUT, REG_32BIT);
349
350 debug_exit();
351
352 return ret;
353}
354
355static int mvebu_a3700_comphy_sgmii_power_on(uint8_t comphy_index,
356 uint32_t comphy_mode)
357{
358 int ret = 0;
359 uint32_t mask, data, offset;
360 uintptr_t sd_ip_addr;
361 int mode = COMPHY_GET_MODE(comphy_mode);
362 int invert = COMPHY_GET_POLARITY_INVERT(comphy_mode);
363
364 debug_enter();
365
366 /* Set selector */
367 mvebu_a3700_comphy_set_phy_selector(comphy_index, comphy_mode);
368
369 /* Serdes IP Base address
370 * COMPHY Lane0 -- USB3/GBE1
371 * COMPHY Lane1 -- PCIe/GBE0
372 */
373 if (comphy_index == COMPHY_LANE0) {
374 /* Get usb3 and gbe */
375 sd_ip_addr = USB3_GBE1_PHY;
376 } else
377 sd_ip_addr = COMPHY_SD_ADDR;
378
379 /*
380 * 1. Reset PHY by setting PHY input port PIN_RESET=1.
381 * 2. Set PHY input port PIN_TX_IDLE=1, PIN_PU_IVREF=1 to keep
382 * PHY TXP/TXN output to idle state during PHY initialization
383 * 3. Set PHY input port PIN_PU_PLL=0, PIN_PU_RX=0, PIN_PU_TX=0.
384 */
385 data = PIN_PU_IVEREF_BIT | PIN_TX_IDLE_BIT | PIN_RESET_COMPHY_BIT;
386 mask = PIN_RESET_CORE_BIT | PIN_PU_PLL_BIT | PIN_PU_RX_BIT |
387 PIN_PU_TX_BIT;
388 offset = MVEBU_COMPHY_REG_BASE + COMPHY_PHY_CFG1_OFFSET(comphy_index);
389 reg_set(offset, data, mask);
390
391 /* 4. Release reset to the PHY by setting PIN_RESET=0. */
392 data = 0;
393 mask = PIN_RESET_COMPHY_BIT;
394 reg_set(offset, data, mask);
395
396 /*
397 * 5. Set PIN_PHY_GEN_TX[3:0] and PIN_PHY_GEN_RX[3:0] to decide COMPHY
398 * bit rate
399 */
400 if (mode == COMPHY_SGMII_MODE) {
401 /* SGMII 1G, SerDes speed 1.25G */
402 data |= SD_SPEED_1_25_G << GEN_RX_SEL_OFFSET;
403 data |= SD_SPEED_1_25_G << GEN_TX_SEL_OFFSET;
Pali Rohár51974d22021-08-27 11:16:43 +0200404 } else if (mode == COMPHY_2500BASEX_MODE) {
405 /* 2500Base-X, SerDes speed 3.125G */
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300406 data |= SD_SPEED_2_5_G << GEN_RX_SEL_OFFSET;
407 data |= SD_SPEED_2_5_G << GEN_TX_SEL_OFFSET;
408 } else {
409 /* Other rates are not supported */
410 ERROR("unsupported SGMII speed on comphy lane%d\n",
411 comphy_index);
412 return -EINVAL;
413 }
414 mask = GEN_RX_SEL_MASK | GEN_TX_SEL_MASK;
415 reg_set(offset, data, mask);
416
417 /*
418 * 6. Wait 10mS for bandgap and reference clocks to stabilize; then
419 * start SW programming.
420 */
421 mdelay(10);
422
423 /* 7. Program COMPHY register PHY_MODE */
424 data = PHY_MODE_SGMII;
425 mask = PHY_MODE_MASK;
426 reg_set16(SGMIIPHY_ADDR(COMPHY_POWER_PLL_CTRL, sd_ip_addr), data, mask);
427
428 /*
429 * 8. Set COMPHY register REFCLK_SEL to select the correct REFCLK
430 * source
431 */
432 data = 0;
433 mask = PHY_REF_CLK_SEL;
434 reg_set16(SGMIIPHY_ADDR(COMPHY_MISC_REG0_ADDR, sd_ip_addr), data, mask);
435
436 /*
437 * 9. Set correct reference clock frequency in COMPHY register
438 * REF_FREF_SEL.
439 */
440 if (get_ref_clk() == 40)
441 data = REF_CLOCK_SPEED_50M;
442 else
443 data = REF_CLOCK_SPEED_25M;
444
445 mask = REF_FREF_SEL_MASK;
446 reg_set16(SGMIIPHY_ADDR(COMPHY_POWER_PLL_CTRL, sd_ip_addr), data, mask);
447
448 /* 10. Program COMPHY register PHY_GEN_MAX[1:0]
449 * This step is mentioned in the flow received from verification team.
450 * However the PHY_GEN_MAX value is only meaningful for other interfaces
451 * (not SGMII). For instance, it selects SATA speed 1.5/3/6 Gbps or PCIe
452 * speed 2.5/5 Gbps
453 */
454
455 /*
456 * 11. Program COMPHY register SEL_BITS to set correct parallel data
457 * bus width
458 */
459 data = DATA_WIDTH_10BIT;
460 mask = SEL_DATA_WIDTH_MASK;
461 reg_set16(SGMIIPHY_ADDR(COMPHY_LOOPBACK_REG0, sd_ip_addr), data, mask);
462
463 /*
464 * 12. As long as DFE function needs to be enabled in any mode,
465 * COMPHY register DFE_UPDATE_EN[5:0] shall be programmed to 0x3F
466 * for real chip during COMPHY power on.
467 * The step 14 exists (and empty) in the original initialization flow
468 * obtained from the verification team. According to the functional
469 * specification DFE_UPDATE_EN already has the default value 0x3F
470 */
471
472 /*
473 * 13. Program COMPHY GEN registers.
474 * These registers should be programmed based on the lab testing result
475 * to achieve optimal performance. Please contact the CEA group to get
476 * the related GEN table during real chip bring-up. We only required to
477 * run though the entire registers programming flow defined by
478 * "comphy_sgmii_phy_init" when the REF clock is 40 MHz. For REF clock
479 * 25 MHz the default values stored in PHY registers are OK.
480 */
481 debug("Running C-DPI phy init %s mode\n",
Pali Rohár51974d22021-08-27 11:16:43 +0200482 mode == COMPHY_2500BASEX_MODE ? "2G5" : "1G");
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300483 if (get_ref_clk() == 40)
484 comphy_sgmii_phy_init(comphy_index, mode, sd_ip_addr);
485
486 /*
487 * 14. [Simulation Only] should not be used for real chip.
488 * By pass power up calibration by programming EXT_FORCE_CAL_DONE
489 * (R02h[9]) to 1 to shorten COMPHY simulation time.
490 */
491
492 /*
493 * 15. [Simulation Only: should not be used for real chip]
494 * Program COMPHY register FAST_DFE_TIMER_EN=1 to shorten RX training
495 * simulation time.
496 */
497
498 /*
499 * 16. Check the PHY Polarity invert bit
500 */
501 data = 0x0;
502 if (invert & COMPHY_POLARITY_TXD_INVERT)
503 data |= TXD_INVERT_BIT;
504 if (invert & COMPHY_POLARITY_RXD_INVERT)
505 data |= RXD_INVERT_BIT;
Pali Rohár741f7d62021-03-24 16:34:45 +0100506 mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
507 reg_set16(SGMIIPHY_ADDR(COMPHY_SYNC_PATTERN_REG, sd_ip_addr), data, mask);
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300508
509 /*
510 * 17. Set PHY input ports PIN_PU_PLL, PIN_PU_TX and PIN_PU_RX to 1 to
511 * start PHY power up sequence. All the PHY register programming should
512 * be done before PIN_PU_PLL=1. There should be no register programming
513 * for normal PHY operation from this point.
514 */
515 reg_set(MVEBU_COMPHY_REG_BASE + COMPHY_PHY_CFG1_OFFSET(comphy_index),
516 PIN_PU_PLL_BIT | PIN_PU_RX_BIT | PIN_PU_TX_BIT,
517 PIN_PU_PLL_BIT | PIN_PU_RX_BIT | PIN_PU_TX_BIT);
518
519 /*
520 * 18. Wait for PHY power up sequence to finish by checking output ports
521 * PIN_PLL_READY_TX=1 and PIN_PLL_READY_RX=1.
522 */
523 ret = polling_with_timeout(MVEBU_COMPHY_REG_BASE +
524 COMPHY_PHY_STATUS_OFFSET(comphy_index),
525 PHY_PLL_READY_TX_BIT | PHY_PLL_READY_RX_BIT,
526 PHY_PLL_READY_TX_BIT | PHY_PLL_READY_RX_BIT,
527 COMPHY_PLL_TIMEOUT, REG_32BIT);
528 if (ret)
529 ERROR("Failed to lock PLL for SGMII PHY %d\n", comphy_index);
530
531 /*
532 * 19. Set COMPHY input port PIN_TX_IDLE=0
533 */
534 reg_set(MVEBU_COMPHY_REG_BASE + COMPHY_PHY_CFG1_OFFSET(comphy_index),
535 0x0, PIN_TX_IDLE_BIT);
536
537 /*
538 * 20. After valid data appear on PIN_RXDATA bus, set PIN_RX_INIT=1. To
539 * start RX initialization. PIN_RX_INIT_DONE will be cleared to 0 by the
540 * PHY After RX initialization is done, PIN_RX_INIT_DONE will be set to
541 * 1 by COMPHY Set PIN_RX_INIT=0 after PIN_RX_INIT_DONE= 1. Please
542 * refer to RX initialization part for details.
543 */
544 reg_set(MVEBU_COMPHY_REG_BASE + COMPHY_PHY_CFG1_OFFSET(comphy_index),
Pali Rohárc9ae2362021-03-24 16:40:46 +0100545 PHY_RX_INIT_BIT, PHY_RX_INIT_BIT);
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300546
547 ret = polling_with_timeout(MVEBU_COMPHY_REG_BASE +
548 COMPHY_PHY_STATUS_OFFSET(comphy_index),
549 PHY_PLL_READY_TX_BIT | PHY_PLL_READY_RX_BIT,
550 PHY_PLL_READY_TX_BIT | PHY_PLL_READY_RX_BIT,
551 COMPHY_PLL_TIMEOUT, REG_32BIT);
552 if (ret)
553 ERROR("Failed to lock PLL for SGMII PHY %d\n", comphy_index);
554
555
556 ret = polling_with_timeout(MVEBU_COMPHY_REG_BASE +
557 COMPHY_PHY_STATUS_OFFSET(comphy_index),
558 PHY_RX_INIT_DONE_BIT, PHY_RX_INIT_DONE_BIT,
559 COMPHY_PLL_TIMEOUT, REG_32BIT);
560 if (ret)
561 ERROR("Failed to init RX of SGMII PHY %d\n", comphy_index);
562
563 debug_exit();
564
565 return ret;
566}
567
Marek Behún4f94cbc2019-11-05 15:21:54 +0100568static int mvebu_a3700_comphy_sgmii_power_off(uint8_t comphy_index)
569{
570 int ret = 0;
571 uint32_t mask, data, offset;
572
573 debug_enter();
574
575 data = PIN_RESET_CORE_BIT | PIN_RESET_COMPHY_BIT;
Pali Rohárc9ae2362021-03-24 16:40:46 +0100576 mask = data;
Marek Behún4f94cbc2019-11-05 15:21:54 +0100577 offset = MVEBU_COMPHY_REG_BASE + COMPHY_PHY_CFG1_OFFSET(comphy_index);
578 reg_set(offset, data, mask);
579
580 debug_exit();
581
582 return ret;
583}
584
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300585static int mvebu_a3700_comphy_usb3_power_on(uint8_t comphy_index,
586 uint32_t comphy_mode)
587{
588 int ret = 0;
589 uintptr_t reg_base = 0;
590 uint32_t mask, data, addr, cfg, ref_clk;
591 void (*usb3_reg_set)(uintptr_t addr, uint32_t reg_offset, uint16_t data,
592 uint16_t mask, int mode);
593 int mode = COMPHY_GET_MODE(comphy_mode);
594 int invert = COMPHY_GET_POLARITY_INVERT(comphy_mode);
595
596 debug_enter();
597
598 /* Set phy seclector */
599 mvebu_a3700_comphy_set_phy_selector(comphy_index, comphy_mode);
600
601 /* Set usb3 reg access func, Lane2 is indirect access */
602 if (comphy_index == COMPHY_LANE2) {
603 usb3_reg_set = &comphy_set_indirect;
604 reg_base = COMPHY_INDIRECT_REG;
605 } else {
606 /* Get the direct access register resource and map */
607 usb3_reg_set = &comphy_usb3_set_direct;
608 reg_base = USB3_GBE1_PHY;
609 }
610
611 /*
612 * 0. Set PHY OTG Control(0x5d034), bit 4, Power up OTG module The
613 * register belong to UTMI module, so it is set in UTMI phy driver.
614 */
615
616 /*
617 * 1. Set PRD_TXDEEMPH (3.5db de-emph)
618 */
619 mask = PRD_TXDEEMPH0_MASK | PRD_TXMARGIN_MASK | PRD_TXSWING_MASK |
620 CFG_TX_ALIGN_POS_MASK;
621 usb3_reg_set(reg_base, COMPHY_REG_LANE_CFG0_ADDR, PRD_TXDEEMPH0_MASK,
622 mask, mode);
623
624 /*
625 * 2. Set BIT0: enable transmitter in high impedance mode
626 * Set BIT[3:4]: delay 2 clock cycles for HiZ off latency
627 * Set BIT6: Tx detect Rx at HiZ mode
628 * Unset BIT15: set to 0 to set USB3 De-emphasize level to -3.5db
629 * together with bit 0 of COMPHY_REG_LANE_CFG0_ADDR register
630 */
631 mask = PRD_TXDEEMPH1_MASK | TX_DET_RX_MODE | GEN2_TX_DATA_DLY_MASK |
632 TX_ELEC_IDLE_MODE_EN;
633 data = TX_DET_RX_MODE | GEN2_TX_DATA_DLY_DEFT | TX_ELEC_IDLE_MODE_EN;
634 usb3_reg_set(reg_base, COMPHY_REG_LANE_CFG1_ADDR, data, mask, mode);
635
636 /*
637 * 3. Set Spread Spectrum Clock Enabled
638 */
639 usb3_reg_set(reg_base, COMPHY_REG_LANE_CFG4_ADDR,
640 SPREAD_SPECTRUM_CLK_EN, SPREAD_SPECTRUM_CLK_EN, mode);
641
642 /*
643 * 4. Set Override Margining Controls From the MAC:
644 * Use margining signals from lane configuration
645 */
646 usb3_reg_set(reg_base, COMPHY_REG_TEST_MODE_CTRL_ADDR,
647 MODE_MARGIN_OVERRIDE, REG_16_BIT_MASK, mode);
648
649 /*
650 * 5. Set Lane-to-Lane Bundle Clock Sampling Period = per PCLK cycles
651 * set Mode Clock Source = PCLK is generated from REFCLK
652 */
653 usb3_reg_set(reg_base, COMPHY_REG_GLOB_CLK_SRC_LO_ADDR, 0x0,
654 (MODE_CLK_SRC | BUNDLE_PERIOD_SEL | BUNDLE_PERIOD_SCALE |
655 BUNDLE_SAMPLE_CTRL | PLL_READY_DLY), mode);
656
657 /*
658 * 6. Set G2 Spread Spectrum Clock Amplitude at 4K
659 */
660 usb3_reg_set(reg_base, COMPHY_REG_GEN2_SET_2,
661 G2_TX_SSC_AMP_VALUE_20, G2_TX_SSC_AMP_MASK, mode);
662
663 /*
664 * 7. Unset G3 Spread Spectrum Clock Amplitude
665 * set G3 TX and RX Register Master Current Select
666 */
667 mask = G3_TX_SSC_AMP_MASK | G3_VREG_RXTX_MAS_ISET_MASK |
668 RSVD_PH03FH_6_0_MASK;
669 usb3_reg_set(reg_base, COMPHY_REG_GEN2_SET_3,
670 G3_VREG_RXTX_MAS_ISET_60U, mask, mode);
671
672 /*
673 * 8. Check crystal jumper setting and program the Power and PLL Control
674 * accordingly Change RX wait
675 */
676 if (get_ref_clk() == 40) {
677 ref_clk = REF_CLOCK_SPEED_40M;
678 cfg = CFG_PM_RXDLOZ_WAIT_12_UNIT;
679
680 } else {
681 /* 25 MHz */
682 ref_clk = USB3_REF_CLOCK_SPEED_25M;
683 cfg = CFG_PM_RXDLOZ_WAIT_7_UNIT;
684 }
685
686 mask = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
687 PU_TX_INTP_BIT | PU_DFE_BIT | PLL_LOCK_BIT | PHY_MODE_MASK |
688 REF_FREF_SEL_MASK;
689 data = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
690 PU_TX_INTP_BIT | PU_DFE_BIT | PHY_MODE_USB3 | ref_clk;
691 usb3_reg_set(reg_base, COMPHY_POWER_PLL_CTRL, data, mask, mode);
692
693 mask = CFG_PM_OSCCLK_WAIT_MASK | CFG_PM_RXDEN_WAIT_MASK |
694 CFG_PM_RXDLOZ_WAIT_MASK;
695 data = CFG_PM_RXDEN_WAIT_1_UNIT | cfg;
696 usb3_reg_set(reg_base, COMPHY_REG_PWR_MGM_TIM1_ADDR, data, mask, mode);
697
698 /*
699 * 9. Enable idle sync
700 */
701 data = UNIT_CTRL_DEFAULT_VALUE | IDLE_SYNC_EN;
702 usb3_reg_set(reg_base, COMPHY_REG_UNIT_CTRL_ADDR, data, REG_16_BIT_MASK,
703 mode);
704
705 /*
706 * 10. Enable the output of 500M clock
707 */
708 data = MISC_REG0_DEFAULT_VALUE | CLK500M_EN;
709 usb3_reg_set(reg_base, COMPHY_MISC_REG0_ADDR, data, REG_16_BIT_MASK,
710 mode);
711
712 /*
713 * 11. Set 20-bit data width
714 */
715 usb3_reg_set(reg_base, COMPHY_LOOPBACK_REG0, DATA_WIDTH_20BIT,
716 REG_16_BIT_MASK, mode);
717
718 /*
719 * 12. Override Speed_PLL value and use MAC PLL
720 */
721 usb3_reg_set(reg_base, COMPHY_KVCO_CAL_CTRL,
722 (SPEED_PLL_VALUE_16 | USE_MAX_PLL_RATE_BIT),
723 REG_16_BIT_MASK, mode);
724
725 /*
726 * 13. Check the Polarity invert bit
727 */
Pali Rohár741f7d62021-03-24 16:34:45 +0100728 data = 0U;
729 if (invert & COMPHY_POLARITY_TXD_INVERT) {
730 data |= TXD_INVERT_BIT;
731 }
732 if (invert & COMPHY_POLARITY_RXD_INVERT) {
733 data |= RXD_INVERT_BIT;
734 }
735 mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
736 usb3_reg_set(reg_base, COMPHY_SYNC_PATTERN_REG, data, mask, mode);
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300737
738 /*
739 * 14. Set max speed generation to USB3.0 5Gbps
740 */
741 usb3_reg_set(reg_base, COMPHY_SYNC_MASK_GEN_REG, PHY_GEN_USB3_5G,
742 PHY_GEN_MAX_MASK, mode);
743
744 /*
745 * 15. Set capacitor value for FFE gain peaking to 0xF
746 */
747 usb3_reg_set(reg_base, COMPHY_REG_GEN3_SETTINGS_3,
748 COMPHY_GEN_FFE_CAP_SEL_VALUE, COMPHY_GEN_FFE_CAP_SEL_MASK,
749 mode);
750
751 /*
752 * 16. Release SW reset
753 */
754 data = MODE_CORE_CLK_FREQ_SEL | MODE_PIPE_WIDTH_32 | MODE_REFDIV_BY_4;
755 usb3_reg_set(reg_base, COMPHY_REG_GLOB_PHY_CTRL0_ADDR, data,
756 REG_16_BIT_MASK, mode);
757
758 /* Wait for > 55 us to allow PCLK be enabled */
759 udelay(PLL_SET_DELAY_US);
760
761 if (comphy_index == COMPHY_LANE2) {
Marek Behún718e02c2019-10-08 17:36:14 +0200762 data = COMPHY_REG_LANE_STATUS1_ADDR + USB3PHY_LANE2_REG_BASE_OFFSET;
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300763 mmio_write_32(reg_base + COMPHY_LANE2_INDIR_ADDR_OFFSET,
764 data);
765
Marek Behún718e02c2019-10-08 17:36:14 +0200766 addr = reg_base + COMPHY_LANE2_INDIR_DATA_OFFSET;
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300767 ret = polling_with_timeout(addr, TXDCLK_PCLK_EN, TXDCLK_PCLK_EN,
768 COMPHY_PLL_TIMEOUT, REG_32BIT);
769 } else {
770 ret = polling_with_timeout(LANE_STATUS1_ADDR(USB3) + reg_base,
771 TXDCLK_PCLK_EN, TXDCLK_PCLK_EN,
772 COMPHY_PLL_TIMEOUT, REG_16BIT);
773 }
774 if (ret)
775 ERROR("Failed to lock USB3 PLL\n");
776
777 debug_exit();
778
779 return ret;
780}
781
782static int mvebu_a3700_comphy_pcie_power_on(uint8_t comphy_index,
783 uint32_t comphy_mode)
784{
785 int ret;
786 uint32_t ref_clk;
Pali Rohár741f7d62021-03-24 16:34:45 +0100787 uint32_t mask, data;
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300788 int invert = COMPHY_GET_POLARITY_INVERT(comphy_mode);
789
790 debug_enter();
791
792 /* 1. Enable max PLL. */
793 reg_set16(LANE_CFG1_ADDR(PCIE) + COMPHY_SD_ADDR,
Pali Rohárc9ae2362021-03-24 16:40:46 +0100794 USE_MAX_PLL_RATE_EN, USE_MAX_PLL_RATE_EN);
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300795
796 /* 2. Select 20 bit SERDES interface. */
797 reg_set16(GLOB_CLK_SRC_LO_ADDR(PCIE) + COMPHY_SD_ADDR,
Pali Rohárc9ae2362021-03-24 16:40:46 +0100798 CFG_SEL_20B, CFG_SEL_20B);
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300799
800 /* 3. Force to use reg setting for PCIe mode */
801 reg_set16(MISC_REG1_ADDR(PCIE) + COMPHY_SD_ADDR,
Pali Rohárc9ae2362021-03-24 16:40:46 +0100802 SEL_BITS_PCIE_FORCE, SEL_BITS_PCIE_FORCE);
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300803
804 /* 4. Change RX wait */
805 reg_set16(PWR_MGM_TIM1_ADDR(PCIE) + COMPHY_SD_ADDR,
806 CFG_PM_RXDEN_WAIT_1_UNIT | CFG_PM_RXDLOZ_WAIT_12_UNIT,
807 (CFG_PM_OSCCLK_WAIT_MASK | CFG_PM_RXDEN_WAIT_MASK |
808 CFG_PM_RXDLOZ_WAIT_MASK));
809
810 /* 5. Enable idle sync */
811 reg_set16(UNIT_CTRL_ADDR(PCIE) + COMPHY_SD_ADDR,
812 UNIT_CTRL_DEFAULT_VALUE | IDLE_SYNC_EN, REG_16_BIT_MASK);
813
814 /* 6. Enable the output of 100M/125M/500M clock */
815 reg_set16(MISC_REG0_ADDR(PCIE) + COMPHY_SD_ADDR,
Pali Rohárbcc4416b2021-03-24 17:03:43 +0100816 MISC_REG0_DEFAULT_VALUE | CLK500M_EN | TXDCLK_2X_SEL | CLK100M_125M_EN,
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300817 REG_16_BIT_MASK);
818
819 /*
820 * 7. Enable TX, PCIE global register, 0xd0074814, it is done in
821 * PCI-E driver
822 */
823
824 /*
825 * 8. Check crystal jumper setting and program the Power and PLL
826 * Control accordingly
827 */
828
829 if (get_ref_clk() == 40)
830 ref_clk = REF_CLOCK_SPEED_40M;
831 else
832 ref_clk = PCIE_REF_CLOCK_SPEED_25M;
833
834 reg_set16(PWR_PLL_CTRL_ADDR(PCIE) + COMPHY_SD_ADDR,
835 (PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
836 PU_TX_INTP_BIT | PU_DFE_BIT | ref_clk | PHY_MODE_PCIE),
837 REG_16_BIT_MASK);
838
839 /* 9. Override Speed_PLL value and use MAC PLL */
840 reg_set16(KVCO_CAL_CTRL_ADDR(PCIE) + COMPHY_SD_ADDR,
841 SPEED_PLL_VALUE_16 | USE_MAX_PLL_RATE_BIT, REG_16_BIT_MASK);
842
843 /* 10. Check the Polarity invert bit */
Pali Rohár741f7d62021-03-24 16:34:45 +0100844 data = 0U;
845 if (invert & COMPHY_POLARITY_TXD_INVERT) {
846 data |= TXD_INVERT_BIT;
847 }
848 if (invert & COMPHY_POLARITY_RXD_INVERT) {
849 data |= RXD_INVERT_BIT;
850 }
851 mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
852 reg_set16(SYNC_PATTERN_REG_ADDR(PCIE) + COMPHY_SD_ADDR, data, mask);
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300853
854 /* 11. Release SW reset */
855 reg_set16(GLOB_PHY_CTRL0_ADDR(PCIE) + COMPHY_SD_ADDR,
856 MODE_CORE_CLK_FREQ_SEL | MODE_PIPE_WIDTH_32,
857 SOFT_RESET | MODE_REFDIV);
858
859 /* Wait for > 55 us to allow PCLK be enabled */
860 udelay(PLL_SET_DELAY_US);
861
862 ret = polling_with_timeout(LANE_STATUS1_ADDR(PCIE) + COMPHY_SD_ADDR,
863 TXDCLK_PCLK_EN, TXDCLK_PCLK_EN,
864 COMPHY_PLL_TIMEOUT, REG_16BIT);
865 if (ret)
866 ERROR("Failed to lock PCIE PLL\n");
867
868 debug_exit();
869
870 return ret;
871}
872
873int mvebu_3700_comphy_power_on(uint8_t comphy_index, uint32_t comphy_mode)
874{
875 int mode = COMPHY_GET_MODE(comphy_mode);
876 int ret = 0;
877
878 debug_enter();
879
880 switch (mode) {
881 case(COMPHY_SATA_MODE):
882 ret = mvebu_a3700_comphy_sata_power_on(comphy_index,
883 comphy_mode);
884 break;
885 case(COMPHY_SGMII_MODE):
Pali Rohár51974d22021-08-27 11:16:43 +0200886 case(COMPHY_2500BASEX_MODE):
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300887 ret = mvebu_a3700_comphy_sgmii_power_on(comphy_index,
888 comphy_mode);
889 break;
890 case (COMPHY_USB3_MODE):
891 case (COMPHY_USB3H_MODE):
892 ret = mvebu_a3700_comphy_usb3_power_on(comphy_index,
893 comphy_mode);
894 break;
895 case (COMPHY_PCIE_MODE):
896 ret = mvebu_a3700_comphy_pcie_power_on(comphy_index,
897 comphy_mode);
898 break;
899 default:
900 ERROR("comphy%d: unsupported comphy mode\n", comphy_index);
901 ret = -EINVAL;
902 break;
903 }
904
905 debug_exit();
906
907 return ret;
908}
909
910static int mvebu_a3700_comphy_usb3_power_off(void)
911{
912 /*
913 * Currently the USB3 MAC will control the USB3 PHY to set it to low
914 * state, thus do not need to power off USB3 PHY again.
915 */
916 debug_enter();
917 debug_exit();
918
919 return 0;
920}
921
922static int mvebu_a3700_comphy_sata_power_off(uint32_t comphy_mode)
923{
924 uintptr_t comphy_indir_regs = COMPHY_INDIRECT_REG;
925 int mode = COMPHY_GET_MODE(comphy_mode);
926 uint32_t offset;
927
928 debug_enter();
929
930 /* Set phy isolation mode */
931 offset = COMPHY_ISOLATION_CTRL_REG + SATAPHY_LANE2_REG_BASE_OFFSET;
932 comphy_set_indirect(comphy_indir_regs, offset, PHY_ISOLATE_MODE,
933 PHY_ISOLATE_MODE, mode);
934
935 /* Power off PLL, Tx, Rx */
936 offset = COMPHY_POWER_PLL_CTRL + SATAPHY_LANE2_REG_BASE_OFFSET;
937 comphy_set_indirect(comphy_indir_regs, offset, 0,
938 PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT, mode);
939
940 debug_exit();
941
942 return 0;
943}
944
945int mvebu_3700_comphy_power_off(uint8_t comphy_index, uint32_t comphy_mode)
946{
947 int mode = COMPHY_GET_MODE(comphy_mode);
948 int err = 0;
949
950 debug_enter();
951
Marek Behún4f94cbc2019-11-05 15:21:54 +0100952 if (!mode) {
953 /*
954 * The user did not specify which mode should be powered off.
955 * In this case we can identify this by reading the phy selector
956 * register.
957 */
958 mode = mvebu_a3700_comphy_get_mode(comphy_index);
959 }
960
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300961 switch (mode) {
Marek Behún4f94cbc2019-11-05 15:21:54 +0100962 case(COMPHY_SGMII_MODE):
Pali Rohár51974d22021-08-27 11:16:43 +0200963 case(COMPHY_2500BASEX_MODE):
Marek Behún4f94cbc2019-11-05 15:21:54 +0100964 err = mvebu_a3700_comphy_sgmii_power_off(comphy_index);
965 break;
Konstantin Porotchkinede192d2018-10-08 16:48:52 +0300966 case (COMPHY_USB3_MODE):
967 case (COMPHY_USB3H_MODE):
968 err = mvebu_a3700_comphy_usb3_power_off();
969 break;
970 case (COMPHY_SATA_MODE):
971 err = mvebu_a3700_comphy_sata_power_off(comphy_mode);
972 break;
973
974 default:
975 debug("comphy%d: power off is not implemented for mode %d\n",
976 comphy_index, mode);
977 break;
978 }
979
980 debug_exit();
981
982 return err;
983}
984
985static int mvebu_a3700_comphy_sata_is_pll_locked(void)
986{
987 uint32_t data, addr;
988 uintptr_t comphy_indir_regs = COMPHY_INDIRECT_REG;
989 int ret = 0;
990
991 debug_enter();
992
993 /* Polling status */
994 mmio_write_32(comphy_indir_regs + COMPHY_LANE2_INDIR_ADDR_OFFSET,
995 COMPHY_LOOPBACK_REG0 + SATAPHY_LANE2_REG_BASE_OFFSET);
996 addr = comphy_indir_regs + COMPHY_LANE2_INDIR_DATA_OFFSET;
997 data = polling_with_timeout(addr, PLL_READY_TX_BIT, PLL_READY_TX_BIT,
998 COMPHY_PLL_TIMEOUT, REG_32BIT);
999
1000 if (data != 0) {
1001 ERROR("TX PLL is not locked\n");
1002 ret = -ETIMEDOUT;
1003 }
1004
1005 debug_exit();
1006
1007 return ret;
1008}
1009
1010int mvebu_3700_comphy_is_pll_locked(uint8_t comphy_index, uint32_t comphy_mode)
1011{
1012 int mode = COMPHY_GET_MODE(comphy_mode);
1013 int ret = 0;
1014
1015 debug_enter();
1016
1017 switch (mode) {
1018 case(COMPHY_SATA_MODE):
1019 ret = mvebu_a3700_comphy_sata_is_pll_locked();
1020 break;
1021
1022 default:
1023 ERROR("comphy[%d] mode[%d] doesn't support PLL lock check\n",
1024 comphy_index, mode);
1025 ret = -EINVAL;
1026 break;
1027 }
1028
1029 debug_exit();
1030
1031 return ret;
1032}