fix(drivers/marvell/comphy): fix name of 3.125G SerDes mode
There is no support for 2.5/3.125G SGMII. This 3.125G SerDes mode is not
SGMII. It is just plain 1000Base-X (as defined in IEEE 802.3z standard)
but upclocked 2.5x. This mode is commonly known under name 2500Base-X.
So remove incorrect SGMII keyword from names and comments and replace it
by more adequate 2500Base-X keyword.
There is no functional change in code, just renaming macros and updating
comments.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: If79aec16cc233f4896aafd75bfbbebb3f172a197
diff --git a/drivers/marvell/comphy/phy-comphy-3700.c b/drivers/marvell/comphy/phy-comphy-3700.c
index 7377e5e..027d07d 100644
--- a/drivers/marvell/comphy/phy-comphy-3700.c
+++ b/drivers/marvell/comphy/phy-comphy-3700.c
@@ -135,7 +135,7 @@
break;
case (COMPHY_SGMII_MODE):
- case (COMPHY_HS_SGMII_MODE):
+ case (COMPHY_2500BASEX_MODE):
if (comphy_index == COMPHY_LANE0)
reg &= ~COMPHY_SELECTOR_USB3_GBE1_SEL_BIT;
else if (comphy_index == COMPHY_LANE1)
@@ -183,7 +183,7 @@
* with COMPHY_USB3D_MODE or COMPHY_USB3H_MODE. (The usb3 phy initialization
* code does not differentiate between these modes.)
* Also it returns COMPHY_SGMII_MODE even if the phy was configures with
- * COMPHY_HS_SGMII_MODE. (The sgmii phy initialization code does differentiate
+ * COMPHY_2500BASEX_MODE. (The sgmii phy initialization code does differentiate
* between these modes, but it is irrelevant when powering the phy off.)
*/
static int mvebu_a3700_comphy_get_mode(uint8_t comphy_index)
@@ -401,8 +401,8 @@
/* SGMII 1G, SerDes speed 1.25G */
data |= SD_SPEED_1_25_G << GEN_RX_SEL_OFFSET;
data |= SD_SPEED_1_25_G << GEN_TX_SEL_OFFSET;
- } else if (mode == COMPHY_HS_SGMII_MODE) {
- /* HS SGMII (2.5G), SerDes speed 3.125G */
+ } else if (mode == COMPHY_2500BASEX_MODE) {
+ /* 2500Base-X, SerDes speed 3.125G */
data |= SD_SPEED_2_5_G << GEN_RX_SEL_OFFSET;
data |= SD_SPEED_2_5_G << GEN_TX_SEL_OFFSET;
} else {
@@ -479,7 +479,7 @@
* 25 MHz the default values stored in PHY registers are OK.
*/
debug("Running C-DPI phy init %s mode\n",
- mode == COMPHY_HS_SGMII_MODE ? "2G5" : "1G");
+ mode == COMPHY_2500BASEX_MODE ? "2G5" : "1G");
if (get_ref_clk() == 40)
comphy_sgmii_phy_init(comphy_index, mode, sd_ip_addr);
@@ -883,7 +883,7 @@
comphy_mode);
break;
case(COMPHY_SGMII_MODE):
- case(COMPHY_HS_SGMII_MODE):
+ case(COMPHY_2500BASEX_MODE):
ret = mvebu_a3700_comphy_sgmii_power_on(comphy_index,
comphy_mode);
break;
@@ -960,7 +960,7 @@
switch (mode) {
case(COMPHY_SGMII_MODE):
- case(COMPHY_HS_SGMII_MODE):
+ case(COMPHY_2500BASEX_MODE):
err = mvebu_a3700_comphy_sgmii_power_off(comphy_index);
break;
case (COMPHY_USB3_MODE):