blob: 9cc5368d8cefd263e4990558b53d36e30eaa4237 [file] [log] [blame]
Yann Gautier4ede20a2020-09-18 15:04:14 +02001// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
2/*
Yann Gautier62944662021-11-02 15:06:01 +01003 * Copyright (c) 2019-2021, STMicroelectronics - All Rights Reserved
Yann Gautier4ede20a2020-09-18 15:04:14 +02004 * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
5 */
6
7#include <dt-bindings/clock/stm32mp1-clksrc.h>
8#include "stm32mp15-ddr3-1x4Gb-1066-binG.dtsi"
9
10/ {
11 memory@c0000000 {
12 device_type = "memory";
13 reg = <0xc0000000 0x20000000>;
14 };
15
16 vin: vin {
17 compatible = "regulator-fixed";
18 regulator-name = "vin";
19 regulator-min-microvolt = <5000000>;
20 regulator-max-microvolt = <5000000>;
21 regulator-always-on;
22 };
23};
24
25&bsec {
26 board_id: board_id@ec {
27 reg = <0xec 0x4>;
28 st,non-secure-otp;
29 };
30};
31
32&clk_hse {
33 st,digbypass;
34};
35
36&cpu0{
37 cpu-supply = <&vddcore>;
38};
39
40&cpu1{
41 cpu-supply = <&vddcore>;
42};
43
44&hash1 {
45 status = "okay";
46};
47
48&i2c4 {
49 pinctrl-names = "default";
50 pinctrl-0 = <&i2c4_pins_a>;
51 i2c-scl-rising-time-ns = <185>;
52 i2c-scl-falling-time-ns = <20>;
53 clock-frequency = <400000>;
54 status = "okay";
55
56 pmic: stpmic@33 {
57 compatible = "st,stpmic1";
58 reg = <0x33>;
59 interrupts-extended = <&exti_pwr 55 IRQ_TYPE_EDGE_FALLING>;
60 interrupt-controller;
61 #interrupt-cells = <2>;
62 status = "okay";
63
64 regulators {
65 compatible = "st,stpmic1-regulators";
66 buck1-supply = <&vin>;
67 buck2-supply = <&vin>;
68 buck3-supply = <&vin>;
69 buck4-supply = <&vin>;
70 ldo1-supply = <&v3v3>;
71 ldo2-supply = <&vin>;
72 ldo3-supply = <&vdd_ddr>;
73 ldo4-supply = <&vin>;
74 ldo5-supply = <&vin>;
75 ldo6-supply = <&v3v3>;
76 vref_ddr-supply = <&vin>;
77 boost-supply = <&vin>;
78 pwr_sw1-supply = <&bst_out>;
79 pwr_sw2-supply = <&bst_out>;
80
81 vddcore: buck1 {
82 regulator-name = "vddcore";
83 regulator-min-microvolt = <1200000>;
84 regulator-max-microvolt = <1350000>;
85 regulator-always-on;
86 regulator-initial-mode = <0>;
87 regulator-over-current-protection;
88 };
89
90 vdd_ddr: buck2 {
91 regulator-name = "vdd_ddr";
92 regulator-min-microvolt = <1350000>;
93 regulator-max-microvolt = <1350000>;
94 regulator-always-on;
95 regulator-initial-mode = <0>;
96 regulator-over-current-protection;
97 };
98
99 vdd: buck3 {
100 regulator-name = "vdd";
101 regulator-min-microvolt = <3300000>;
102 regulator-max-microvolt = <3300000>;
103 regulator-always-on;
104 st,mask-reset;
105 regulator-initial-mode = <0>;
106 regulator-over-current-protection;
107 };
108
109 v3v3: buck4 {
110 regulator-name = "v3v3";
111 regulator-min-microvolt = <3300000>;
112 regulator-max-microvolt = <3300000>;
113 regulator-always-on;
114 regulator-over-current-protection;
115 regulator-initial-mode = <0>;
116 };
117
118 v1v8_audio: ldo1 {
119 regulator-name = "v1v8_audio";
120 regulator-min-microvolt = <1800000>;
121 regulator-max-microvolt = <1800000>;
122 regulator-always-on;
123 };
124
125 v3v3_hdmi: ldo2 {
126 regulator-name = "v3v3_hdmi";
127 regulator-min-microvolt = <3300000>;
128 regulator-max-microvolt = <3300000>;
129 regulator-always-on;
130 };
131
132 vtt_ddr: ldo3 {
133 regulator-name = "vtt_ddr";
134 regulator-min-microvolt = <500000>;
135 regulator-max-microvolt = <750000>;
136 regulator-always-on;
137 regulator-over-current-protection;
138 };
139
140 vdd_usb: ldo4 {
141 regulator-name = "vdd_usb";
142 regulator-min-microvolt = <3300000>;
143 regulator-max-microvolt = <3300000>;
Yann Gautier4ede20a2020-09-18 15:04:14 +0200144 };
145
146 vdda: ldo5 {
147 regulator-name = "vdda";
148 regulator-min-microvolt = <2900000>;
149 regulator-max-microvolt = <2900000>;
150 regulator-boot-on;
151 };
152
153 v1v2_hdmi: ldo6 {
154 regulator-name = "v1v2_hdmi";
155 regulator-min-microvolt = <1200000>;
156 regulator-max-microvolt = <1200000>;
157 regulator-always-on;
158 };
159
160 vref_ddr: vref_ddr {
161 regulator-name = "vref_ddr";
162 regulator-always-on;
163 regulator-over-current-protection;
164 };
165
166 bst_out: boost {
167 regulator-name = "bst_out";
168 };
169
170 vbus_otg: pwr_sw1 {
171 regulator-name = "vbus_otg";
172 };
173
174 vbus_sw: pwr_sw2 {
175 regulator-name = "vbus_sw";
176 regulator-active-discharge = <1>;
177 };
178 };
179 };
180};
181
182&iwdg2 {
183 timeout-sec = <32>;
184 status = "okay";
185 secure-status = "okay";
186};
187
188&pwr_regulators {
189 vdd-supply = <&vdd>;
190 vdd_3v3_usbfs-supply = <&vdd_usb>;
191};
192
193&rcc {
194 secure-status = "disabled";
195 st,clksrc = <
196 CLK_MPU_PLL1P
197 CLK_AXI_PLL2P
198 CLK_MCU_PLL3P
199 CLK_PLL12_HSE
200 CLK_PLL3_HSE
201 CLK_PLL4_HSE
202 CLK_RTC_LSE
203 CLK_MCO1_DISABLED
204 CLK_MCO2_DISABLED
205 >;
206
207 st,clkdiv = <
208 1 /*MPU*/
209 0 /*AXI*/
210 0 /*MCU*/
211 1 /*APB1*/
212 1 /*APB2*/
213 1 /*APB3*/
214 1 /*APB4*/
215 2 /*APB5*/
216 23 /*RTC*/
217 0 /*MCO1*/
218 0 /*MCO2*/
219 >;
220
221 st,pkcs = <
222 CLK_CKPER_HSE
223 CLK_FMC_ACLK
224 CLK_QSPI_ACLK
Yann Gautierdbbf79a2021-05-17 11:25:37 +0200225 CLK_ETH_PLL4P
Yann Gautier4ede20a2020-09-18 15:04:14 +0200226 CLK_SDMMC12_PLL4P
227 CLK_DSI_DSIPLL
228 CLK_STGEN_HSE
229 CLK_USBPHY_HSE
230 CLK_SPI2S1_PLL3Q
231 CLK_SPI2S23_PLL3Q
232 CLK_SPI45_HSI
233 CLK_SPI6_HSI
234 CLK_I2C46_HSI
235 CLK_SDMMC3_PLL4P
236 CLK_USBO_USBPHY
237 CLK_ADC_CKPER
238 CLK_CEC_LSE
239 CLK_I2C12_HSI
240 CLK_I2C35_HSI
241 CLK_UART1_HSI
242 CLK_UART24_HSI
243 CLK_UART35_HSI
244 CLK_UART6_HSI
245 CLK_UART78_HSI
246 CLK_SPDIF_PLL4P
247 CLK_FDCAN_PLL4R
248 CLK_SAI1_PLL3Q
249 CLK_SAI2_PLL3Q
250 CLK_SAI3_PLL3Q
251 CLK_SAI4_PLL3Q
252 CLK_RNG1_LSI
253 CLK_RNG2_LSI
254 CLK_LPTIM1_PCLK1
255 CLK_LPTIM23_PCLK3
256 CLK_LPTIM45_LSE
257 >;
258
259 /* VCO = 1300.0 MHz => P = 650 (CPU) */
260 pll1: st,pll@0 {
261 compatible = "st,stm32mp1-pll";
262 reg = <0>;
263 cfg = < 2 80 0 0 0 PQR(1,0,0) >;
264 frac = < 0x800 >;
265 };
266
267 /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
268 pll2: st,pll@1 {
269 compatible = "st,stm32mp1-pll";
270 reg = <1>;
271 cfg = <2 65 1 0 0 PQR(1,1,1)>;
272 frac = <0x1400>;
273 };
274
275 /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
276 pll3: st,pll@2 {
277 compatible = "st,stm32mp1-pll";
278 reg = <2>;
279 cfg = <1 33 1 16 36 PQR(1,1,1)>;
280 frac = <0x1a04>;
281 };
282
283 /* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
284 pll4: st,pll@3 {
285 compatible = "st,stm32mp1-pll";
286 reg = <3>;
287 cfg = <3 98 5 7 7 PQR(1,1,1)>;
288 };
289};
290
291&rng1 {
292 status = "okay";
293};
294
295&rtc {
296 status = "okay";
297};
298
299&sdmmc1 {
300 pinctrl-names = "default";
301 pinctrl-0 = <&sdmmc1_b4_pins_a>;
302 disable-wp;
303 st,neg-edge;
304 bus-width = <4>;
305 vmmc-supply = <&v3v3>;
306 status = "okay";
307};
308
309&timers15 {
310 secure-status = "okay";
311};
312
313&uart4 {
314 pinctrl-names = "default";
315 pinctrl-0 = <&uart4_pins_a>;
316 status = "okay";
317};
318
319&uart7 {
320 pinctrl-names = "default";
Yann Gautierbb053d52021-10-20 17:22:32 +0200321 pinctrl-0 = <&uart7_pins_c>;
Yann Gautier4ede20a2020-09-18 15:04:14 +0200322 status = "disabled";
323};
324
325&usart3 {
326 pinctrl-names = "default";
Yann Gautierbb053d52021-10-20 17:22:32 +0200327 pinctrl-0 = <&usart3_pins_c>;
Yann Gautier4ede20a2020-09-18 15:04:14 +0200328 uart-has-rtscts;
329 status = "disabled";
330};
331
332&usbotg_hs {
333 phys = <&usbphyc_port1 0>;
334 phy-names = "usb2-phy";
335 usb-role-switch;
336 status = "okay";
337};
338
339&usbphyc {
340 status = "okay";
341};
342
343&usbphyc_port0 {
344 phy-supply = <&vdd_usb>;
345};
346
347&usbphyc_port1 {
348 phy-supply = <&vdd_usb>;
349};