blob: f9ee4492f5d080b8b25a66ad354f174b9cbd0779 [file] [log] [blame]
/*
* Copyright (c) 2013-2020, ARM Limited and Contributors. All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
#include <assert.h>
#include <common/debug.h>
#include <drivers/arm/smmu_v3.h>
#include <fconf_hw_config_getter.h>
#include <lib/fconf/fconf.h>
#include <lib/fconf/fconf_dyn_cfg_getter.h>
#include <lib/mmio.h>
#include <plat/arm/common/arm_config.h>
#include <plat/arm/common/plat_arm.h>
#include <plat/common/platform.h>
#include "fvp_private.h"
void __init bl31_early_platform_setup2(u_register_t arg0,
u_register_t arg1, u_register_t arg2, u_register_t arg3)
{
#if !RESET_TO_BL31 && !BL2_AT_EL3
const struct dyn_cfg_dtb_info_t *soc_fw_config_info;
INFO("BL31 FCONF: FW_CONFIG address = %lx\n", (uintptr_t)arg1);
/* Fill the properties struct with the info from the config dtb */
fconf_populate("FW_CONFIG", arg1);
soc_fw_config_info = FCONF_GET_PROPERTY(dyn_cfg, dtb, SOC_FW_CONFIG_ID);
if (soc_fw_config_info != NULL) {
arg1 = soc_fw_config_info->config_addr;
}
#endif /* !RESET_TO_BL31 && !BL2_AT_EL3 */
arm_bl31_early_platform_setup((void *)arg0, arg1, arg2, (void *)arg3);
/* Initialize the platform config for future decision making */
fvp_config_setup();
/*
* Initialize the correct interconnect for this cluster during cold
* boot. No need for locks as no other CPU is active.
*/
fvp_interconnect_init();
/*
* Enable coherency in interconnect for the primary CPU's cluster.
* Earlier bootloader stages might already do this (e.g. Trusted
* Firmware's BL1 does it) but we can't assume so. There is no harm in
* executing this code twice anyway.
* FVP PSCI code will enable coherency for other clusters.
*/
fvp_interconnect_enable();
/* Initialize System level generic or SP804 timer */
fvp_timer_init();
/* On FVP RevC, initialize SMMUv3 */
if ((arm_config.flags & ARM_CONFIG_FVP_HAS_SMMUV3) != 0U)
smmuv3_init(PLAT_FVP_SMMUV3_BASE);
}
void __init bl31_plat_arch_setup(void)
{
arm_bl31_plat_arch_setup();
/*
* For RESET_TO_BL31 systems, BL31 is the first bootloader to run.
* So there is no BL2 to load the HW_CONFIG dtb into memory before
* control is passed to BL31.
*/
#if !RESET_TO_BL31 && !BL2_AT_EL3
/* HW_CONFIG was also loaded by BL2 */
const struct dyn_cfg_dtb_info_t *hw_config_info;
hw_config_info = FCONF_GET_PROPERTY(dyn_cfg, dtb, HW_CONFIG_ID);
assert(hw_config_info != NULL);
fconf_populate("HW_CONFIG", hw_config_info->config_addr);
#endif
}
unsigned int plat_get_syscnt_freq2(void)
{
unsigned int counter_base_frequency;
#if !RESET_TO_BL31 && !BL2_AT_EL3
/* Get the frequency through FCONF API for HW_CONFIG */
counter_base_frequency = FCONF_GET_PROPERTY(hw_config, cpu_timer, clock_freq);
if (counter_base_frequency > 0U) {
return counter_base_frequency;
}
#endif
/* Read the frequency from Frequency modes table */
counter_base_frequency = mmio_read_32(ARM_SYS_CNTCTL_BASE + CNTFID_OFF);
/* The first entry of the frequency modes table must not be 0 */
if (counter_base_frequency == 0U) {
panic();
}
return counter_base_frequency;
}