| #!/bin/ash |
| |
| interface=$1 |
| cmd_type=$2 |
| full_cmd=$3 |
| |
| work_mode="RUN" # RUN/PRINT/DEBUG |
| tmp_file="$HOME/.tmp_ate_config" |
| phy_idx=$(echo ${interface} | tr -dc '0-9') |
| |
| cmd=$(echo ${full_cmd} | sed s/=/' '/g | cut -d " " -f 1) |
| param=$(echo ${full_cmd} | sed s/=/' '/g | cut -d " " -f 2) |
| |
| function do_cmd() { |
| case ${work_mode} in |
| "RUN") |
| eval "$1" |
| ;; |
| "PRINT") |
| echo "$1" |
| ;; |
| "DEBUG") |
| eval "$1" |
| echo "$1" |
| ;; |
| esac |
| } |
| |
| function record_config() { |
| if [ -f ${tmp_file} ]; then |
| if grep -q $1 ${tmp_file}; then |
| sed -i "/$1/c\\$1=$2" ${tmp_file} |
| else |
| echo "$1=$2" >> ${tmp_file} |
| fi |
| else |
| echo "$1=$2" >> ${tmp_file} |
| fi |
| } |
| |
| function get_config() { |
| echo "$(cat ${tmp_file} | grep $1 | sed s/=/' '/g | cut -d " " -f 2)" |
| } |
| |
| function simple_convert() { |
| if [ "$1" = "ATETXCNT" ]; then |
| echo "tx_count" |
| elif [ "$1" = "ATETXLEN" ]; then |
| echo "tx_length" |
| elif [ "$1" = "ATETXMCS" ]; then |
| echo "tx_rate_idx" |
| elif [ "$1" = "ATEVHTNSS" ]; then |
| echo "tx_rate_nss" |
| elif [ "$1" = "ATETXLDPC" ]; then |
| echo "tx_rate_ldpc" |
| elif [ "$1" = "ATETXSTBC" ]; then |
| echo "tx_rate_stbc" |
| elif [ "$1" = "ATEPKTTXTIME" ]; then |
| echo "tx_time" |
| elif [ "$1" = "ATEIPG" ]; then |
| echo "tx_ipg" |
| elif [ "$1" = "ATEDUTYCYCLE" ]; then |
| echo "tx_duty_cycle" |
| elif [ "$1" = "ATETXFREQOFFSET" ]; then |
| echo "freq_offset" |
| else |
| echo "unknown" |
| fi |
| } |
| |
| function convert_tx_mode() { |
| if [ "$1" = "0" ]; then |
| echo "cck" |
| elif [ "$1" = "1" ]; then |
| echo "ofdm" |
| elif [ "$1" = "2" ]; then |
| echo "ht" |
| elif [ "$1" = "4" ]; then |
| echo "vht" |
| elif [ "$1" = "8" ]; then |
| echo "he_su" |
| elif [ "$1" = "9" ]; then |
| echo "he_er" |
| elif [ "$1" = "10" ]; then |
| echo "he_tb" |
| elif [ "$1" = "11" ]; then |
| echo "he_mu" |
| else |
| echo "unknown" |
| fi |
| } |
| |
| function convert_gi { |
| local tx_mode=$1 |
| local val=$2 |
| local sgi="0" |
| local he_ltf="0" |
| |
| case ${tx_mode} in |
| "ht"|"vht") |
| sgi=${val} |
| ;; |
| "he_su"|"he_er") |
| case ${val} in |
| "0") |
| ;; |
| "1") |
| he_ltf="1" |
| ;; |
| "2") |
| sgi="1" |
| he_ltf="1" |
| ;; |
| "3") |
| sgi="2" |
| he_ltf="2" |
| ;; |
| "4") |
| he_ltf="2" |
| ;; |
| *) |
| echo "unknown gi" |
| esac |
| ;; |
| "he_mu") |
| case ${val} in |
| "0") |
| he_ltf="2" |
| ;; |
| "1") |
| he_ltf="1" |
| ;; |
| "2") |
| sgi="1" |
| he_ltf="1" |
| ;; |
| "3") |
| sgi="2" |
| he_ltf="2" |
| ;; |
| *) |
| echo "unknown gi" |
| esac |
| ;; |
| "he_tb") |
| case ${val} in |
| "0") |
| sgi="1" |
| ;; |
| "1") |
| sgi="1" |
| he_ltf="1" |
| ;; |
| "2") |
| sgi="2" |
| he_ltf="2" |
| ;; |
| *) |
| echo "unknown gi" |
| esac |
| ;; |
| *) |
| echo "unknown tx_rate_mode, can't transform gi" |
| esac |
| |
| do_cmd "mt76-test ${interface} set tx_rate_sgi=${sgi} tx_ltf=${he_ltf}" |
| } |
| |
| function convert_channel { |
| local band=$(echo $1 | sed s/:/' '/g | cut -d " " -f 2) |
| local ch=$(echo $1 | sed s/:/' '/g | cut -d " " -f 1) |
| local bw=$(get_config "ATETXBW" | cut -d ":" -f 1) |
| |
| if [ "${band}" = "0" ]; then |
| case ${bw} in |
| "1") |
| if [ "${ch}" -ge "1" ] && [ "${ch}" -le "7" ]; then |
| local bw_str="HT40+" |
| else |
| local bw_str="HT40-" |
| fi |
| ;; |
| "0") |
| local bw_str="HT20" |
| ;; |
| esac |
| elif [ "${band}" = "1" ]; then |
| case ${bw} in |
| "5") |
| local bw_str="160MHz" |
| ;; |
| "2") |
| local bw_str="80MHz" |
| ;; |
| "1") |
| if [ "${ch}" == "36" ] || [ "${ch}" == "44" ] || [ "${ch}" == "52" ] || [ "${ch}" == "60" ] || \ |
| [ "${ch}" == "100" ] || [ "${ch}" == "108" ] || [ "${ch}" == "116" ] || [ "${ch}" == "124" ] || \ |
| [ "${ch}" == "132" ] || [ "${ch}" == "132" ] || [ "${ch}" == "140" ] || [ "${ch}" == "149" ] || \ |
| [ "${ch}" == "157" ] |
| then |
| local bw_str="HT40+" |
| else |
| local bw_str="HT40-" |
| fi |
| ;; |
| "0") |
| local bw_str="HT20" |
| ;; |
| esac |
| else |
| echo "6G Todo" |
| fi |
| |
| do_cmd "iw dev mon${phy_idx} set channel ${ch} ${bw_str}" |
| } |
| |
| function do_ate_work() { |
| local ate_cmd=$1 |
| |
| case ${ate_cmd} in |
| "ATESTART") |
| local if_str=$(ifconfig | grep mon${phy_idx}) |
| |
| if [ ! -z "${if_str}" -a "${if_str}" != " " ]; then |
| echo "ATE already starts." |
| else |
| do_cmd "iw phy ${interface} interface add mon${phy_idx} type monitor" |
| do_cmd "iw dev wlan${phy_idx} del" |
| do_cmd "ifconfig mon${phy_idx} up" |
| fi |
| ;; |
| "ATESTOP") |
| local if_str=$(ifconfig | grep mon${phy_idx}) |
| |
| if [ -z "${if_str}" -a "${if_str}" != " " ]; then |
| echo "ATE does not start." |
| else |
| do_cmd "mt76-test ${interface} set state=off" |
| do_cmd "iw dev mon${phy_idx} del" |
| do_cmd "iw phy ${interface} interface add wlan${phy_idx} type managed" |
| do_cmd "ifconfig wlan${phy_idx} up" |
| fi |
| ;; |
| "TXFRAME") |
| do_cmd "mt76-test ${interface} set state=tx_frames" |
| ;; |
| "TXSTOP"|"RXSTOP"|"TXREVERT") |
| do_cmd "mt76-test ${interface} set state=idle" |
| ;; |
| "RXFRAME") |
| do_cmd "mt76-test ${interface} set state=rx_frames" |
| ;; |
| "TXCONT") |
| do_cmd "mt76-test ${interface} set state=tx_cont" |
| ;; |
| "TXCOMMIT") |
| tx_mode=$(convert_tx_mode $(get_config "ATETXMODE")) |
| case ${tx_mode} in |
| "ht"|"vht"|"he_su") |
| do_cmd "mt76-test ${interface} set aid=1" |
| ;; |
| *) |
| ;; |
| esac |
| do_cmd "mt76-test ${interface} set state=idle" |
| ;; |
| esac |
| } |
| |
| if [ "${cmd_type}" = "set" ]; then |
| skip=0 |
| use_ated=0 |
| case ${cmd} in |
| "ATE") |
| do_ate_work ${param} |
| |
| skip=1 |
| ;; |
| "ATETXCNT"|"ATETXLEN"|"ATETXMCS"|"ATEVHTNSS"|"ATETXLDPC"|"ATETXSTBC"| \ |
| "ATEPKTTXTIME"|"ATEIPG"|"ATEDUTYCYCLE"|"ATETXFREQOFFSET") |
| cmd_new=$(simple_convert ${cmd}) |
| param_new=${param} |
| ;; |
| "ATETXANT"|"ATERXANT") |
| cmd_new="tx_antenna" |
| param_new=${param} |
| ;; |
| "ATETXGI") |
| tx_mode=$(convert_tx_mode $(get_config "ATETXMODE")) |
| convert_gi ${tx_mode} ${param} |
| skip=1 |
| ;; |
| "ATETXMODE") |
| cmd_new="tx_rate_mode" |
| param_new=$(convert_tx_mode ${param}) |
| record_config ${cmd} ${param} |
| ;; |
| "ATETXPOW0"|"ATETXPOW1"|"ATETXPOW2"|"ATETXPOW3") |
| cmd_new="tx_power" |
| param_new="${param},0,0,0" |
| ;; |
| "ATETXBW") |
| record_config ${cmd} ${param} |
| skip=1 |
| ;; |
| "ATECHANNEL") |
| convert_channel ${param} |
| skip=1 |
| ;; |
| "ATECTRLBANDIDX") |
| echo "Unused command, please use phy0/phy1 to switch" |
| skip=1 |
| ;; |
| "bufferMode") |
| if [ "${param}" = "2" ]; then |
| do_cmd "ated -i ${interface} -c \"eeprom update\"" |
| fi |
| skip=1 |
| ;; |
| "ResetCounter"|"ATERXSTATRESET") |
| skip=1 |
| ;; |
| *) |
| echo "Unknown command to set" |
| skip=1 |
| esac |
| |
| if [ "${skip}" != "1" ]; then |
| do_cmd "mt76-test ${interface} set ${cmd_new}=${param_new}" |
| fi |
| elif [ "${cmd_type}" = "show" ]; then |
| do_cmd "mt76-test ${interface} dump" |
| do_cmd "mt76-test ${interface} dump stats" |
| elif [ "${cmd_type}" = "e2p" ]; then |
| offset=$(printf "0x%s" ${cmd}) |
| val=$(printf "0x%s" ${param}) |
| |
| # eeprom offset write |
| if [[ ${full_cmd} == *"="* ]]; then |
| tmp=$((${val} & 0xff)) |
| tmp=$(printf "0x%x" ${tmp}) |
| do_cmd "ated -i ${interface} -c \"eeprom set ${offset}=${tmp}\"" |
| |
| offset=$((${offset})) |
| offset=$(expr ${offset} + "1") |
| offset=$(printf "0x%x" ${offset}) |
| tmp=$(((${val} >> 8) & 0xff)) |
| tmp=$(printf "0x%x" ${tmp}) |
| do_cmd "ated -i ${interface} -c \"eeprom set ${offset}=${tmp}\"" |
| else |
| v1=$(do_cmd "ated -i ${interface} -c \"eeprom read ${param}\"") |
| v1=$(echo "${v1}" | grep "val =" | cut -d '(' -f 2 | grep -o -E '[0-9]+') |
| |
| tmp=$(printf "0x%s" ${param}) |
| tmp=$((${tmp})) |
| param2=$(expr ${tmp} + "1") |
| param2=$(printf "%x" ${param2}) |
| v2=$(do_cmd "ated -i ${interface} -c \"eeprom read ${param2}\"") |
| v2=$(echo "${v2}" | grep "val =" | cut -d '(' -f 2 | grep -o -E '[0-9]+') |
| |
| param=$(printf "0x%s" ${param}) |
| printf "[0x%04x]:0x%02x%02x\n" ${param} ${v2} ${v1} |
| fi |
| elif [ "${cmd_type}" = "mac" ]; then |
| regidx=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/regidx |
| regval=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/regval |
| offset=$(printf "0x%s" ${cmd}) |
| val=$(printf "0x%s" ${param}) |
| |
| echo ${offset} > ${regidx} |
| # reg write |
| if [[ ${full_cmd} == *"="* ]]; then |
| echo ${val} > ${regval} |
| else |
| res=$(cat ${regval} | cut -d 'x' -f 2) |
| printf "%s mac:[%s]:%s\n" ${interface} ${offset} ${res} |
| fi |
| else |
| echo "Unknown command" |
| fi |