| #!/bin/ash |
| |
| interface=$1 # phy0/phy1/ra0 |
| cmd_type=$2 # set/show/e2p/mac/dump |
| full_cmd=$3 |
| interface_ori=${interface} |
| SOC_start_idx="0" |
| SOC_end_idx="0" |
| is_connac3="0" |
| |
| work_mode="RUN" # RUN/PRINT/DEBUG |
| iwpriv_file="/tmp/iwpriv_wrapper" |
| interface_file="/tmp/interface" |
| phy_idx=$(echo ${interface} | tr -dc '0-9') |
| |
| function do_cmd() { |
| case ${work_mode} in |
| "RUN") |
| eval "$1" |
| ;; |
| "PRINT") |
| echo "$1" |
| ;; |
| "DEBUG") |
| echo "$1" |
| eval "$1" |
| ;; |
| esac |
| } |
| |
| function print_debug() { |
| if [ "${work_mode}" = "DEBUG" ]; then |
| echo "$1" |
| fi |
| } |
| |
| function write_dmesg() { |
| echo "$1" > /dev/kmsg |
| } |
| |
| function record_config() { |
| local config=$1 |
| local tmp_file=$3 |
| |
| # check it is SOC(mt7986)/Eagle or PCIE card (mt7915/7916), and write its config |
| if [ ${tmp_file} != ${interface_file} ]; then |
| if [ $phy_idx -lt $SOC_start_idx ]; then |
| config="${config}_PCIE" |
| elif [ $phy_idx -ge $SOC_start_idx ]; then |
| config="${config}_SOC" |
| fi |
| fi |
| |
| if [ -f ${tmp_file} ]; then |
| if grep -q ${config} ${tmp_file}; then |
| sed -i "/${config}/c\\${config}=$2" ${tmp_file} |
| else |
| echo "${config}=$2" >> ${tmp_file} |
| fi |
| else |
| echo "${config}=$2" >> ${tmp_file} |
| fi |
| } |
| |
| function get_config() { |
| local config=$1 |
| local tmp_file=$2 |
| |
| if [ ! -f ${tmp_file} ]; then |
| echo "" |
| return |
| fi |
| |
| # check it is SOC(mt7986)/Eagle or PCIE card (mt7915/7916), and write its config |
| if [ ${tmp_file} != ${interface_file} ]; then |
| if [ $phy_idx -lt $SOC_start_idx ]; then |
| config="${config}_PCIE" |
| elif [ $phy_idx -ge $SOC_start_idx ]; then |
| config="${config}_SOC" |
| fi |
| fi |
| |
| if grep -q ${config} ${tmp_file}; then |
| echo "$(cat ${tmp_file} | grep ${config} | sed s/=/' '/g | cut -d " " -f 2)" |
| else |
| echo "" |
| fi |
| } |
| |
| function parse_sku { |
| SOC_start_idx=$(get_config "STARTIDX" ${interface_file}) |
| SOC_end_idx=$(get_config "ENDIDX" ${interface_file}) |
| is_connac3=$(get_config "IS_CONNAC3" ${interface_file}) |
| local eeprom_file=/sys/kernel/debug/ieee80211/phy0/mt76/eeprom |
| if [ -z "${SOC_start_idx}" ] || [ -z "${SOC_end_idx}" ] || [ -z "${is_connac3}" ]; then |
| if [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7916")" ]; then |
| SOC_start_idx="2" |
| SOC_end_idx="3" |
| is_connac3="0" |
| elif [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7915")" ]; then |
| SOC_start_idx="1" |
| SOC_end_idx="2" |
| is_connac3="0" |
| elif [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7981")" ]; then |
| SOC_start_idx="0" |
| SOC_end_idx="1" |
| is_connac3="0" |
| elif [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7986")" ]; then |
| SOC_start_idx="0" |
| SOC_end_idx="1" |
| is_connac3="0" |
| elif [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7990")" ]; then |
| SOC_start_idx="0" |
| SOC_end_idx="2" |
| is_connac3="1" |
| elif [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7992")" ]; then |
| SOC_start_idx="0" |
| SOC_end_idx="1" |
| is_connac3="1" |
| else |
| echo "Interface Conversion Failed!" |
| echo "Please use iwpriv <phy0/phy1/..> set <...> or configure the sku of your board manually by the following commands" |
| echo "For AX3000/AX6000:" |
| echo " echo STARTIDX=0 >> ${interface_file}" |
| echo " echo ENDIDX=1 >> ${interface_file}" |
| echo " echo IS_CONNAC3=0 >> ${interface_file}" |
| echo "For AX7800:" |
| echo " echo STARTIDX=2 >> ${interface_file}" |
| echo " echo ENDIDX=3 >> ${interface_file}" |
| echo " echo IS_CONNAC3=0 >> ${interface_file}" |
| echo "For AX8400:" |
| echo " echo STARTIDX=1 >> ${interface_file}" |
| echo " echo ENDIDX=2 >> ${interface_file}" |
| echo " echo IS_CONNAC3=0 >> ${interface_file}" |
| echo "For Eagle:" |
| echo " echo STARTIDX=0 >> ${interface_file}" |
| echo " echo ENDIDX=2 >> ${interface_file}" |
| echo " echo IS_CONNAC3=1 >> ${interface_file}" |
| echo "For Kite:" |
| echo " echo STARTIDX=0 >> ${interface_file}" |
| echo " echo ENDIDX=1 >> ${interface_file}" |
| echo " echo IS_CONNAC3=1 >> ${interface_file}" |
| exit 0 |
| fi |
| record_config "STARTIDX" ${SOC_start_idx} ${interface_file} |
| record_config "ENDIDX" ${SOC_end_idx} ${interface_file} |
| record_config "IS_CONNAC3" ${is_connac3} ${interface_file} |
| fi |
| } |
| |
| function convert_interface { |
| if [ ${is_connac3} == "0" ]; then |
| if [[ $1 == "raix"* ]]; then |
| phy_idx=1 |
| elif [[ $1 == "rai"* ]]; then |
| phy_idx=0 |
| elif [[ $1 == "rax"* ]]; then |
| phy_idx=$((SOC_start_idx+1)) |
| else |
| phy_idx=$SOC_start_idx |
| fi |
| |
| # convert phy index according to band idx |
| local band_idx=$(get_config "ATECTRLBANDIDX" ${iwpriv_file}) |
| if [ "${band_idx}" = "0" ]; then |
| if [[ $1 == "raix"* ]]; then |
| phy_idx=0 |
| elif [[ $1 == "rax"* ]]; then |
| phy_idx=$SOC_start_idx |
| fi |
| elif [ "${band_idx}" = "1" ]; then |
| if [[ $1 == "rai"* ]]; then |
| # AX8400: mt7915 remain phy0 |
| # AX7800: mt7916 becomes phy1 |
| phy_idx=$((SOC_start_idx-1)) |
| elif [[ $1 == "ra"* ]]; then |
| phy_idx=$((SOC_start_idx+1)) |
| fi |
| fi |
| else |
| # Eagle has different mapping method |
| # phy0: ra0 |
| # phy1: rai0 |
| # phy2: rax0 |
| if [[ $1 == "rai"* ]]; then |
| phy_idx=1 |
| elif [[ $1 == "rax"* ]]; then |
| phy_idx=2 |
| else |
| phy_idx=0 |
| fi |
| fi |
| |
| interface="phy${phy_idx}" |
| } |
| |
| function change_band_idx { |
| local new_idx=$1 |
| local new_phy_idx=$phy_idx |
| |
| local old_idx=$(get_config "ATECTRLBANDIDX" ${iwpriv_file}) |
| |
| |
| if [[ ${interface_ori} == "ra"* ]]; then |
| if [ -z "${old_idx}" ] || [ "${old_idx}" != "${new_idx}" ]; then |
| if [ "${new_idx}" = "0" ]; then |
| # raix0 & rai0 becomes rai0 |
| if [[ $interface_ori == "rai"* ]]; then |
| new_phy_idx=0 |
| # rax0 & ra0 becomes ra0 |
| elif [[ $interface_ori == "ra"* ]]; then |
| new_phy_idx=$SOC_start_idx |
| fi |
| elif [ "${new_idx}" = "1" ]; then |
| # raix0 & rai0 becomes raix0 |
| if [[ $interface_ori == "rai"* ]]; then |
| # For AX8400 => don't change phy idx |
| if [ ${SOC_start_idx} != "1" ]; then |
| new_phy_idx=1 |
| fi |
| # rax0 & ra0 becomes rax0 |
| elif [[ $interface_ori == "ra"* ]]; then |
| new_phy_idx=$((SOC_start_idx+1)) |
| fi |
| fi |
| fi |
| |
| if [ ${new_phy_idx} != ${phy_idx} ]; then |
| do_ate_work "ATESTOP" |
| phy_idx=$new_phy_idx |
| interface="phy${phy_idx}" |
| do_ate_work "ATESTART" |
| fi |
| fi |
| record_config "ATECTRLBANDIDX" ${new_idx} ${iwpriv_file} |
| } |
| |
| function simple_convert() { |
| if [ "$1" = "ATETXCNT" ]; then |
| echo "tx_count" |
| elif [ "$1" = "ATETXLEN" ]; then |
| echo "tx_length" |
| elif [ "$1" = "ATETXMCS" ]; then |
| echo "tx_rate_idx" |
| elif [ "$1" = "ATEVHTNSS" ]; then |
| echo "tx_rate_nss" |
| elif [ "$1" = "ATETXLDPC" ]; then |
| echo "tx_rate_ldpc" |
| elif [ "$1" = "ATETXSTBC" ]; then |
| echo "tx_rate_stbc" |
| elif [ "$1" = "ATEPKTTXTIME" ]; then |
| echo "tx_time" |
| elif [ "$1" = "ATEIPG" ]; then |
| echo "tx_ipg" |
| elif [ "$1" = "ATEDUTYCYCLE" ]; then |
| echo "tx_duty_cycle" |
| elif [ "$1" = "ATETXFREQOFFSET" ]; then |
| echo "freq_offset" |
| else |
| echo "undefined" |
| fi |
| } |
| |
| function convert_tx_mode() { |
| # Remove leading zeros |
| local tx_mode=$(echo $1 | sed -r 's/0+([0-9]+)/\1/g') |
| |
| if [ "$tx_mode" = "0" ]; then |
| echo "cck" |
| elif [ "$tx_mode" = "1" ]; then |
| echo "ofdm" |
| elif [ "$tx_mode" = "2" ]; then |
| echo "ht" |
| elif [ "$tx_mode" = "4" ]; then |
| echo "vht" |
| elif [ "$tx_mode" = "8" ]; then |
| echo "he_su" |
| elif [ "$tx_mode" = "9" ]; then |
| echo "he_er" |
| elif [ "$tx_mode" = "10" ]; then |
| echo "he_tb" |
| elif [ "$tx_mode" = "11" ]; then |
| echo "he_mu" |
| elif [ "$tx_mode" = "13" ]; then |
| echo "eht_su" |
| elif [ "$tx_mode" = "14" ]; then |
| echo "eht_tb" |
| elif [ "$tx_mode" = "15" ]; then |
| echo "eht_mu" |
| else |
| echo "undefined" |
| fi |
| } |
| |
| function convert_gi { |
| local tx_mode=$1 |
| local val=$2 |
| local sgi="0" |
| local he_ltf="0" |
| |
| case ${tx_mode} in |
| "ht"|"vht") |
| sgi=${val} |
| ;; |
| "he_su"|"he_er") |
| case ${val} in |
| "0") |
| ;; |
| "1") |
| he_ltf="1" |
| ;; |
| "2") |
| sgi="1" |
| he_ltf="1" |
| ;; |
| "3") |
| sgi="2" |
| he_ltf="2" |
| ;; |
| "4") |
| he_ltf="2" |
| ;; |
| *) |
| echo "unknown gi" |
| esac |
| ;; |
| "he_mu") |
| case ${val} in |
| "0") |
| he_ltf="2" |
| ;; |
| "1") |
| he_ltf="1" |
| ;; |
| "2") |
| sgi="1" |
| he_ltf="1" |
| ;; |
| "3") |
| sgi="2" |
| he_ltf="2" |
| ;; |
| *) |
| echo "unknown gi" |
| esac |
| ;; |
| "he_tb") |
| case ${val} in |
| "0") |
| sgi="1" |
| ;; |
| "1") |
| sgi="1" |
| he_ltf="1" |
| ;; |
| "2") |
| sgi="2" |
| he_ltf="2" |
| ;; |
| *) |
| echo "unknown gi" |
| esac |
| ;; |
| *) |
| print_debug "legacy mode no need gi" |
| esac |
| |
| do_cmd "mt76-test ${interface} set tx_rate_sgi=${sgi} tx_ltf=${he_ltf}" |
| } |
| |
| function convert_channel { |
| local ctrl_band_idx=$(get_config "ATECTRLBANDIDX" ${iwpriv_file}) |
| local ch=$(echo $1 | sed s/:/' '/g | cut -d " " -f 1) |
| local bw=$(get_config "ATETXBW" ${iwpriv_file} | cut -d ":" -f 1) |
| local bw_str="HT20" |
| local base_chan=1 |
| local control_freq=0 |
| local base_freq=0 |
| local band=$(echo $1 | sed s/:/' '/g | cut -d " " -f 2) |
| local temp=$((phy_idx+1)) |
| |
| # Handle ATECTRLBANDIDX |
| if [ ! -z ${ctrl_band_idx} ]; then |
| if [ "${ctrl_band_idx}" == "1" ] && [ ${band} == "0" ]; then |
| local temp=$(cat "/etc/config/wireless"| grep "option band" | sed -n ${temp}p | cut -c 15) |
| if [ "${temp}" == "2" ]; then |
| local band=0 |
| elif [ "${temp}" == "5" ]; then |
| local band=1 |
| elif [ "${temp}" == "6" ]; then |
| local band=2 |
| else |
| echo "iwpriv wrapper band translate error!" |
| fi |
| else |
| # mt7915 in AX8400 case: band should be determined by only the input band |
| if [ "${SOC_start_idx}" == "1" ] && [ ${phy_idx} == "0" ]; then |
| local band=$((band)) |
| else |
| local band=$((ctrl_band_idx * band)) |
| fi |
| fi |
| fi |
| |
| if [[ $1 != *":"* ]] || [ "${band}" = "0" ]; then |
| case ${bw} in |
| "1") |
| if [ "${ch}" -lt "3" ] || [ "${ch}" -gt "12" ]; then |
| local bw_str="HT20" |
| else |
| local bw_str="HT40+" |
| ch=$(expr ${ch} - "2") |
| fi |
| ;; |
| esac |
| local base_freq=2412 |
| elif [ "${band}" = "1" ]; then |
| case ${bw} in |
| "5") |
| bw_str="160MHz" |
| if [ ${ch} -lt "68" ]; then |
| ch="36" |
| elif [ ${ch} -lt "100" ]; then |
| ch="68" |
| elif [ ${ch} -lt "132" ]; then |
| ch="100" |
| elif [ ${ch} -lt "181" ]; then |
| ch="149" |
| fi |
| ;; |
| "2") |
| bw_str="80MHz" |
| if [ ${ch} -lt "52" ]; then |
| ch="36" |
| elif [ ${ch} -lt "68" ]; then |
| ch="52" |
| elif [ ${ch} -lt "84" ]; then |
| ch="68" |
| elif [ ${ch} -lt "100" ]; then |
| ch="84" |
| elif [ ${ch} -lt "116" ]; then |
| ch="100" |
| elif [ ${ch} -lt "132" ]; then |
| ch="116" |
| elif [ ${ch} -lt "149" ]; then |
| ch="132" |
| elif [ ${ch} -lt "165" ]; then |
| ch="149" |
| elif [ ${ch} -lt "181" ]; then |
| ch="165" |
| fi |
| ;; |
| "1") |
| if [ ${ch} -lt "44" ]; then |
| ch=$([ "${ch}" -lt "40" ] && echo "36" || echo "40") |
| bw_str=$([ "${ch}" -le "38" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "52" ]; then |
| ch=$([ "${ch}" -lt "48" ] && echo "44" || echo "48") |
| bw_str=$([ "${ch}" -le "46" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "60" ]; then |
| ch=$([ "${ch}" -lt "56" ] && echo "52" || echo "56") |
| bw_str=$([ "${ch}" -le "54" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "68" ]; then |
| ch=$([ "${ch}" -lt "64" ] && echo "60" || echo "64") |
| bw_str=$([ "${ch}" -le "62" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "76" ]; then |
| ch=$([ "${ch}" -lt "72" ] && echo "68" || echo "72") |
| bw_str=$([ "${ch}" -le "70" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "84" ]; then |
| ch=$([ "${ch}" -lt "80" ] && echo "76" || echo "80") |
| bw_str=$([ "${ch}" -le "78" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "92" ]; then |
| ch=$([ "${ch}" -lt "88" ] && echo "84" || echo "88") |
| bw_str=$([ "${ch}" -le "86" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "100" ]; then |
| ch=$([ "${ch}" -lt "96" ] && echo "92" || echo "96") |
| bw_str=$([ "${ch}" -le "94" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "108" ]; then |
| ch=$([ "${ch}" -lt "104" ] && echo "100" || echo "104") |
| bw_str=$([ "${ch}" -le "102" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "116" ]; then |
| ch=$([ "${ch}" -lt "112" ] && echo "108" || echo "112") |
| bw_str=$([ "${ch}" -le "110" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "124" ]; then |
| ch=$([ "${ch}" -lt "120" ] && echo "116" || echo "120") |
| bw_str=$([ "${ch}" -le "118" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "132" ]; then |
| ch=$([ "${ch}" -lt "128" ] && echo "124" || echo "128") |
| bw_str=$([ "${ch}" -le "126" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "140" ]; then |
| ch=$([ "${ch}" -lt "136" ] && echo "132" || echo "136") |
| bw_str=$([ "${ch}" -le "134" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "149" ]; then |
| ch=$([ "${ch}" -lt "144" ] && echo "140" || echo "144") |
| bw_str=$([ "${ch}" -le "142" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "157" ]; then |
| ch=$([ "${ch}" -lt "153" ] && echo "149" || echo "153") |
| bw_str=$([ "${ch}" -le "151" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "165" ]; then |
| ch=$([ "${ch}" -lt "161" ] && echo "157" || echo "161") |
| bw_str=$([ "${ch}" -le "159" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "173" ]; then |
| ch=$([ "${ch}" -lt "169" ] && echo "165" || echo "169") |
| bw_str=$([ "${ch}" -le "167" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "181" ]; then |
| ch=$([ "${ch}" -lt "177" ] && echo "173" || echo "177") |
| bw_str=$([ "${ch}" -le "175" ] && echo "HT40+" || echo "HT40-") |
| fi |
| ;; |
| "0") |
| local bw_str="HT20" |
| ;; |
| esac |
| local base_freq=5180 |
| local base_chan=36 |
| else |
| local base_freq=5955 |
| case ${bw} in |
| "12") |
| local bw_str="320" |
| if [ ${ch} == "31" ]; then |
| local control_freq="5955" |
| elif [ ${ch} == "63" ]; then |
| local control_freq="6115" |
| elif [ ${ch} == "95" ]; then |
| local control_freq="6275" |
| elif [ ${ch} == "127" ]; then |
| local control_freq="6435" |
| elif [ ${ch} == "159" ]; then |
| local control_freq="6595" |
| elif [ ${ch} == "191" ]; then |
| local control_freq="6755" |
| fi |
| local center_freq=$(((ch - base_chan) * 5 + base_freq)) |
| do_cmd "iw dev mon${phy_idx} set freq ${control_freq} ${bw_str} ${center_freq}" |
| return |
| ;; |
| "5") |
| bw_str="160MHz" |
| if [ ${ch} -lt "33" ]; then |
| ch="1" |
| elif [ ${ch} -lt "65" ]; then |
| ch="33" |
| elif [ ${ch} -lt "97" ]; then |
| ch="65" |
| elif [ ${ch} -lt "129" ]; then |
| ch="97" |
| elif [ ${ch} -lt "161" ]; then |
| ch="129" |
| elif [ ${ch} -lt "193" ]; then |
| ch="161" |
| elif [ ${ch} -lt "225" ]; then |
| ch="193" |
| fi |
| ;; |
| "2") |
| bw_str="80MHz" |
| if [ ${ch} -lt "17" ]; then |
| ch="1" |
| elif [ ${ch} -lt "33" ]; then |
| ch="17" |
| elif [ ${ch} -lt "49" ]; then |
| ch="33" |
| elif [ ${ch} -lt "65" ]; then |
| ch="49" |
| elif [ ${ch} -lt "81" ]; then |
| ch="65" |
| elif [ ${ch} -lt "97" ]; then |
| ch="81" |
| elif [ ${ch} -lt "113" ]; then |
| ch="97" |
| elif [ ${ch} -lt "129" ]; then |
| ch="113" |
| elif [ ${ch} -lt "145" ]; then |
| ch="129" |
| elif [ ${ch} -lt "161" ]; then |
| ch="145" |
| elif [ ${ch} -lt "177" ]; then |
| ch="161" |
| elif [ ${ch} -lt "193" ]; then |
| ch="177" |
| elif [ ${ch} -lt "209" ]; then |
| ch="193" |
| elif [ ${ch} -lt "225" ]; then |
| ch="209" |
| fi |
| ;; |
| "1") |
| if [ ${ch} -lt "9" ]; then |
| ch=$([ "${ch}" -lt "5" ] && echo "1" || echo "5") |
| bw_str=$([ "${ch}" -le "3" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "17" ]; then |
| ch=$([ "${ch}" -lt "13" ] && echo "9" || echo "13") |
| bw_str=$([ "${ch}" -le "11" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "25" ]; then |
| ch=$([ "${ch}" -lt "21" ] && echo "17" || echo "21") |
| bw_str=$([ "${ch}" -le "19" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "33" ]; then |
| ch=$([ "${ch}" -lt "29" ] && echo "25" || echo "29") |
| bw_str=$([ "${ch}" -le "27" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "33" ]; then |
| ch=$([ "${ch}" -lt "29" ] && echo "25" || echo "29") |
| bw_str=$([ "${ch}" -le "27" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "41" ]; then |
| ch=$([ "${ch}" -lt "37" ] && echo "33" || echo "37") |
| bw_str=$([ "${ch}" -le "35" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "49" ]; then |
| ch=$([ "${ch}" -lt "45" ] && echo "41" || echo "45") |
| bw_str=$([ "${ch}" -le "43" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "57" ]; then |
| ch=$([ "${ch}" -lt "53" ] && echo "49" || echo "53") |
| bw_str=$([ "${ch}" -le "51" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "65" ]; then |
| ch=$([ "${ch}" -lt "61" ] && echo "57" || echo "61") |
| bw_str=$([ "${ch}" -le "59" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "73" ]; then |
| ch=$([ "${ch}" -lt "69" ] && echo "65" || echo "69") |
| bw_str=$([ "${ch}" -le "67" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "81" ]; then |
| ch=$([ "${ch}" -lt "77" ] && echo "73" || echo "77") |
| bw_str=$([ "${ch}" -le "75" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "89" ]; then |
| ch=$([ "${ch}" -lt "85" ] && echo "81" || echo "85") |
| bw_str=$([ "${ch}" -le "83" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "97" ]; then |
| ch=$([ "${ch}" -lt "93" ] && echo "89" || echo "93") |
| bw_str=$([ "${ch}" -le "91" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "105" ]; then |
| ch=$([ "${ch}" -lt "101" ] && echo "97" || echo "101") |
| bw_str=$([ "${ch}" -le "99" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "113" ]; then |
| ch=$([ "${ch}" -lt "109" ] && echo "105" || echo "109") |
| bw_str=$([ "${ch}" -le "107" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "121" ]; then |
| ch=$([ "${ch}" -lt "117" ] && echo "113" || echo "117") |
| bw_str=$([ "${ch}" -le "115" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "129" ]; then |
| ch=$([ "${ch}" -lt "125" ] && echo "121" || echo "125") |
| bw_str=$([ "${ch}" -le "123" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "137" ]; then |
| ch=$([ "${ch}" -lt "133" ] && echo "129" || echo "133") |
| bw_str=$([ "${ch}" -le "131" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "145" ]; then |
| ch=$([ "${ch}" -lt "141" ] && echo "137" || echo "141") |
| bw_str=$([ "${ch}" -le "139" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "153" ]; then |
| ch=$([ "${ch}" -lt "149" ] && echo "145" || echo "149") |
| bw_str=$([ "${ch}" -le "147" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "161" ]; then |
| ch=$([ "${ch}" -lt "157" ] && echo "153" || echo "157") |
| bw_str=$([ "${ch}" -le "155" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "169" ]; then |
| ch=$([ "${ch}" -lt "165" ] && echo "161" || echo "165") |
| bw_str=$([ "${ch}" -le "163" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "177" ]; then |
| ch=$([ "${ch}" -lt "173" ] && echo "169" || echo "173") |
| bw_str=$([ "${ch}" -le "171" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "185" ]; then |
| ch=$([ "${ch}" -lt "181" ] && echo "177" || echo "181") |
| bw_str=$([ "${ch}" -le "179" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "193" ]; then |
| ch=$([ "${ch}" -lt "189" ] && echo "185" || echo "189") |
| bw_str=$([ "${ch}" -le "187" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "201" ]; then |
| ch=$([ "${ch}" -lt "197" ] && echo "193" || echo "197") |
| bw_str=$([ "${ch}" -le "195" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "209" ]; then |
| ch=$([ "${ch}" -lt "205" ] && echo "201" || echo "205") |
| bw_str=$([ "${ch}" -le "203" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "217" ]; then |
| ch=$([ "${ch}" -lt "213" ] && echo "209" || echo "213") |
| bw_str=$([ "${ch}" -le "211" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "225" ]; then |
| ch=$([ "${ch}" -lt "221" ] && echo "217" || echo "221") |
| bw_str=$([ "${ch}" -le "219" ] && echo "HT40+" || echo "HT40-") |
| elif [ ${ch} -lt "233" ]; then |
| ch=$([ "${ch}" -lt "229" ] && echo "225" || echo "229") |
| bw_str=$([ "${ch}" -le "227" ] && echo "HT40+" || echo "HT40-") |
| fi |
| ;; |
| "0") |
| local bw_str="HT20" |
| ;; |
| esac |
| fi |
| |
| local control_freq=$(((ch - base_chan) * 5 + base_freq)) |
| do_cmd "iw dev mon${phy_idx} set freq ${control_freq} ${bw_str}" |
| } |
| |
| function convert_rxstat { |
| local res=$(do_cmd "mt76-test ${interface} dump stats") |
| local mdrdy=$(echo "${res}" | grep "rx_packets" | cut -d "=" -f 2) |
| local fcs_error=$(echo "${res}" | grep "rx_fcs_error" | cut -d "=" -f 2) |
| local rcpi=$(echo "${res}" | grep "last_rcpi" | cut -d "=" -f 2 | sed 's/,/ /g') |
| local ib_rssi=$(echo "${res}" | grep "last_ib_rssi" | cut -d "=" -f 2 | sed 's/,/ /g') |
| local wb_rssi=$(echo "${res}" | grep "last_wb_rssi" | cut -d "=" -f 2 | sed 's/,/ /g') |
| local rx_ok=$(expr ${mdrdy} - ${fcs_error}) |
| |
| write_dmesg "rcpi: ${rcpi}" |
| write_dmesg "fagc rssi ib: ${ib_rssi}" |
| write_dmesg "fagc rssi wb: ${wb_rssi}" |
| write_dmesg "all_mac_rx_mdrdy_cnt: ${mdrdy}" |
| write_dmesg "all_mac_rx_fcs_err_cnt: ${fcs_error}" |
| write_dmesg "all_mac_rx_ok_cnt : ${rx_ok}" |
| } |
| |
| function set_mac_addr { |
| record_config ${cmd} ${param} ${iwpriv_file} |
| |
| local addr1=$(get_config "ATEDA" ${iwpriv_file}) |
| local addr2=$(get_config "ATESA" ${iwpriv_file}) |
| local addr3=$(get_config "ATEBSSID" ${iwpriv_file}) |
| |
| if [ -z "${addr1}" ]; then |
| addr1="00:11:22:33:44:55" |
| fi |
| if [ -z "${addr2}" ]; then |
| addr2="00:11:22:33:44:55" |
| fi |
| if [ -z "${addr3}" ]; then |
| addr3="00:11:22:33:44:55" |
| fi |
| |
| do_cmd "mt76-test phy${phy_idx} set mac_addrs=${addr1},${addr2},${addr3}" |
| } |
| |
| function convert_ibf { |
| local cmd=$1 |
| local param=$2 |
| local new_cmd="" |
| local new_param=$(echo ${param} | sed s/":"/","/g) |
| |
| case ${cmd} in |
| "ATETxBfInit") |
| new_cmd="init" |
| new_param="1" |
| do_cmd "mt76-test phy${phy_idx} set state=idle" |
| ;; |
| "ATETxBfGdInit") |
| new_cmd="golden_init" |
| new_param="1" |
| do_cmd "mt76-test phy${phy_idx} set state=idle" |
| ;; |
| "ATEIBFPhaseComp") |
| new_cmd="phase_comp" |
| new_param="${new_param}" |
| ;; |
| "ATEEBfProfileConfig") |
| new_cmd="ebf_prof_update" |
| ;; |
| "ATEIBfProfileConfig") |
| new_cmd="ibf_prof_update" |
| ;; |
| "ATEIBfInstCal") |
| new_cmd="phase_cal" |
| ;; |
| "ATEIBfGdCal") |
| local group=${new_param:0:2} |
| local group_l_m_h=${new_param:3:2} |
| local band_idx=${new_param:6:2} |
| local cal_type=${new_param:9:2} |
| local version=${new_param:12} |
| local lna_level="00" |
| |
| # only ibf 2.0 will set version, so add null check for backward compatibility |
| if [ -z $version ]; then |
| version="00" |
| fi |
| |
| new_cmd="phase_cal" |
| new_param="${group},${group_l_m_h},${band_idx},${cal_type},${lna_level},${version}" |
| ;; |
| "TxBfTxApply") |
| new_cmd="apply_tx" |
| ;; |
| "ATETxPacketWithBf") |
| local bf_on=${new_param:0:2} |
| local aid="01" |
| local wlan_idx=${new_param:3:2} |
| local update="00" |
| local tx_count=${new_param:6} |
| |
| new_cmd="tx_prep" |
| new_param="${bf_on},${aid},${wlan_idx},${update}" |
| if [ "${tx_count}" = "00" ]; then |
| new_param="${new_param} aid=1 tx_count=10000000 tx_length=1024" |
| else |
| new_param="${new_param} aid=1 tx_count=${tx_count} tx_length=1024" |
| fi |
| do_cmd "mt76-test phy${phy_idx} set state=idle" |
| ;; |
| "TxBfProfileData20MAllWrite") |
| new_cmd="prof_update_all" |
| ;; |
| "ATEIBFPhaseE2pUpdate") |
| new_cmd="e2p_update" |
| ;; |
| "ATEIBFPhaseVerify") |
| local group=${new_param:0:2} |
| local group_l_m_h=${new_param:3:2} |
| local band_idx=${new_param:6:2} |
| local phase_cal_type=${new_param:9:2} |
| local LNA_gain_level=${new_param:12:2} |
| local read_from_e2p=${new_param:15:2} |
| |
| do_cmd "mt76-test phy${phy_idx} set txbf_act=phase_comp txbf_param=1,${band_idx},${group},${read_from_e2p},0" |
| new_cmd="phase_cal" |
| new_param="${group},${group_l_m_h},${band_idx},${phase_cal_type},${LNA_gain_level}" |
| ;; |
| "TxBfProfileTagRead") |
| new_cmd="pfmu_tag_read" |
| ;; |
| "TxBfProfileTagWrite") |
| new_cmd="pfmu_tag_write" |
| ;; |
| "TxBfProfileTagInValid") |
| new_cmd="set_invalid_prof" |
| ;; |
| "StaRecBfRead") |
| new_cmd="sta_rec_read" |
| ;; |
| "TriggerSounding") |
| new_cmd="trigger_sounding" |
| ;; |
| "StopSounding") |
| new_cmd="stop_sounding" |
| new_param="0" |
| ;; |
| "TxBfTxCmd") |
| new_cmd="txcmd" |
| ;; |
| "ATEConTxETxBfGdProc") |
| local tx_rate_mode=$(convert_tx_mode ${new_param:0:2}) |
| local tx_rate_idx=${new_param:3:2} |
| local bw=$(echo ${new_param:6:2} | sed 's/^0//') |
| local channel=${new_param:9:3} |
| local channel2=${new_param:13:3} |
| local band=${new_param:17} |
| |
| new_cmd="ebf_golden_init" |
| do_ate_work "ATESTART" |
| do_cmd "mt76-test phy${phy_idx} set state=idle" |
| record_config "ATETXBW" ${bw} ${iwpriv_file} |
| convert_channel "${channel}:${band}" |
| if [ "${bw}" = "5" ]; then |
| new_param="1,1" |
| else |
| new_param="1,0" |
| fi |
| do_cmd "mt76-test phy${phy_idx} set tx_rate_mode=${tx_rate_mode} tx_rate_idx=${tx_rate_idx} tx_rate_sgi=0" |
| ;; |
| "ATEConTxETxBfInitProc") |
| local tx_rate_mode=$(convert_tx_mode ${new_param:0:2}) |
| local tx_rate_idx=${new_param:3:2} |
| local bw=$(echo ${new_param:6:2} | sed 's/^0//') |
| local tx_rate_nss=${new_param:9:2} |
| local tx_stream=${new_param:12:2} |
| local tx_power=${new_param:15:2} |
| local channel=$(echo ${new_param:18:3} | sed 's/^0//') |
| local channel2=${new_param:22:3} |
| local band=${new_param:26:1} |
| local tx_length=$(echo ${new_param:28:5} | sed 's/^0//') |
| |
| new_cmd="ebf_init" |
| do_ate_work "ATESTART" |
| do_cmd "mt76-test phy${phy_idx} set state=idle" |
| record_config "ATETXBW" ${bw} ${iwpriv_file} |
| convert_channel "${channel}:${band}" |
| new_param="1" |
| do_cmd "mt76-test phy${phy_idx} set tx_rate_mode=${tx_rate_mode} tx_rate_idx=${tx_rate_idx} tx_rate_nss=${tx_rate_nss} tx_rate_sgi=0 tx_rate_ldpc=1 tx_power=${tx_power},0,0,0 tx_count=10000000 tx_length=${tx_length} tx_ipg=4" |
| ;; |
| *) |
| esac |
| |
| do_cmd "mt76-test phy${phy_idx} set txbf_act=${new_cmd} txbf_param=${new_param}" |
| |
| if [ "${cmd}" = "ATETxPacketWithBf" ]; then |
| do_cmd "mt76-test phy${phy_idx} set state=tx_frames" |
| elif [ "${cmd}" = "ATEConTxETxBfInitProc" ]; then |
| local wlan_idx="1" |
| if [ ${is_connac3} == "1" ]; then |
| local wlan_idx=$((phy_idx+1)) |
| fi |
| do_cmd "mt76-test phy${phy_idx} set aid=1" |
| do_cmd "mt76-test phy${phy_idx} set txbf_act=stop_sounding txbf_param=1" |
| do_cmd "mt76-test phy${phy_idx} set txbf_act=update_ch txbf_param=1" |
| do_cmd "mt76-test phy${phy_idx} set txbf_act=ebf_prof_update txbf_param=0,0,0" |
| do_cmd "mt76-test phy${phy_idx} set txbf_act=apply_tx txbf_param=${wlan_idx},1,0,0,0" |
| if [ ${is_connac3} == "1" ]; then |
| do_cmd "mt76-test phy${phy_idx} set txbf_act=txcmd txbf_param=1,1,1" |
| fi |
| do_cmd "mt76-test phy${phy_idx} set txbf_act=pfmu_tag_read txbf_param=0,1" |
| do_cmd "mt76-test phy${phy_idx} set txbf_act=sta_rec_read txbf_param=${wlan_idx}" |
| do_cmd "mt76-test phy${phy_idx} set txbf_act=trigger_sounding txbf_param=0,1,0,${wlan_idx},0,0,0" |
| do_cmd "mt76-test phy${phy_idx} set txbf_act=trigger_sounding txbf_param=2,1,ff,${wlan_idx},0,0,0" |
| do_cmd "mt76-test phy${phy_idx} set state=rx_frames" |
| elif [ "${cmd}" = "ATEConTxETxBfGdProc" ]; then |
| do_cmd "mt76-test phy${phy_idx} set aid=1" |
| do_cmd "mt76-test phy${phy_idx} set state=rx_frames" |
| elif [ "${cmd}" = "ATETxBfInit" ]; then |
| do_cmd "mt76-test phy${phy_idx} set aid=1" |
| elif [ "${cmd}" = "ATETxBfGdInit" ]; then |
| do_cmd "mt76-test phy${phy_idx} set aid=1" |
| elif [ "${cmd}" = "ATEIBFPhaseE2pUpdate" ]; then |
| do_cmd "atenl -i phy${phy_idx} -c \"eeprom ibf sync\"" |
| fi |
| } |
| |
| function convert_ruinfo { |
| local new_param=$1 |
| |
| do_cmd "mt76-test phy${phy_idx} set state=idle" |
| while [ -n "$new_param" ] |
| do |
| [ ${new_param:1:1} = ':' ] && { |
| new_param=${new_param:2} |
| } |
| local oIFS="$IFS"; IFS=":"; set -- $new_param; IFS="$oIFS" |
| |
| parsing_ruinfo $new_param |
| new_param=${new_param:${#1}+1} |
| done |
| } |
| |
| function parsing_ruinfo { |
| local new_param=$1 |
| local oIFS="$IFS"; IFS="-:"; set -- $new_param; IFS="$oIFS" |
| |
| # $7 is Start spatial stream and it should be 0, $9 is alpha, not used |
| do_cmd "mt76-test phy${phy_idx} set tx_rate_mode=he_mu tx_rate_sgi=0 tx_ltf=0 ru_alloc=$1 aid=$2 ru_idx=$3\ |
| tx_rate_idx=$4 tx_rate_ldpc=$5 tx_rate_nss=$6 tx_length=$8" |
| } |
| |
| function convert_dfs { |
| local cmd=$1 |
| local param=$2 |
| |
| case ${cmd} in |
| "DfsRxCtrl") |
| local offchan_ch="$(echo $param | cut -d ':' -f1)" |
| local offchan_bw="$(echo $param | cut -d ':' -f2)" |
| |
| if [ "$offchan_bw" = "0" ]; then |
| offchan_bw="20" |
| elif [ "$offchan_bw" = "1" ]; then |
| offchan_bw="40" |
| elif [ "$offchan_bw" = "2" ]; then |
| offchan_bw="80" |
| elif [ "$offchan_bw" = "3" ]; then |
| offchan_bw="160" |
| fi |
| |
| do_cmd "mt76-test phy${phy_idx} set state=idle" |
| do_cmd "mt76-test phy${phy_idx} set offchan_ch=${offchan_ch} offchan_bw=${offchan_bw}" |
| ;; |
| "DfsRxHist") |
| local ipi_th="$(echo $param | cut -d ':' -f 1)" |
| local ipi_period="$(echo $param | cut -d ':' -f 2)" |
| local ipi_antenna="$(echo $param | cut -d ':' -f 3)" |
| |
| if [ -z $ipi_antenna ]; then |
| do_cmd "mt76-test phy${phy_idx} set ipi_threshold=${ipi_th} ipi_period=${ipi_period}" |
| else |
| do_cmd "mt76-test phy${phy_idx} set ipi_threshold=${ipi_th} ipi_period=${ipi_period} ipi_antenna_idx=${ipi_antenna}" |
| fi |
| ;; |
| *) |
| esac |
| } |
| |
| function do_ate_work() { |
| local ate_cmd=$1 |
| |
| case ${ate_cmd} in |
| "ATESTART") |
| local if_str=$(ifconfig | grep mon${phy_idx}) |
| |
| if [ ! -z "${if_str}" -a "${if_str}" != " " ]; then |
| echo "ATE already starts." |
| else |
| do_cmd "iw phy ${interface} interface add mon${phy_idx} type monitor" |
| |
| if [ $phy_idx -ge $SOC_start_idx ]; then |
| local end_idx=$SOC_end_idx |
| local start_idx=$SOC_start_idx |
| else |
| local end_idx=$((SOC_start_idx-1)) |
| local start_idx="0" |
| fi |
| |
| for phy_index in $( seq $start_idx $end_idx ) |
| do |
| # "phy#-1" would not be in iw dev, therefore it will grep the line from the phy#${phy_index} to the end |
| local prev_phy_index=$((phy_index-1)) |
| local if_num=$(iw dev | awk "/phy#${phy_index}/,/phy#${prev_phy_index}/" | grep -c Interface) |
| local j="1" |
| # avoid del_if_count reset to 0 when start ate on another band in dbdc case |
| local del_if_count=$(get_config "DEL_IF${phy_index}_NUM" ${interface_file}) |
| if [ -z "${del_if_count}" ]; then |
| local del_if_count="0" |
| fi |
| |
| for if_count in $( seq 1 $if_num ) |
| do |
| local del_if=$(iw dev | awk "/phy#${phy_index}/,/phy#${prev_phy_index}/" | grep Interface | sed -n ${j}p | cut -d " " -f 2) |
| if [ ! -z "${del_if}" ] && [[ "$del_if" != *"mon"* ]]; then |
| do_cmd "iw dev ${del_if} del" |
| del_if_count=$((del_if_count+1)) |
| # handle the case of multiple interface in a phy |
| record_config "DEL_IF${phy_index}-${del_if_count}" ${del_if} ${interface_file} |
| else |
| # j add 1 to skip mon interface |
| j=$((j+1)) |
| fi |
| done |
| record_config "DEL_IF${phy_index}_NUM" ${del_if_count} ${interface_file} |
| done |
| |
| do_cmd "ifconfig mon${phy_idx} up" |
| do_cmd "iw reg set VV" |
| fi |
| ;; |
| "ATESTOP") |
| local if_str=$(ifconfig | grep mon${phy_idx}) |
| |
| if [ -z "${if_str}" -a "${if_str}" != " " ]; then |
| echo "ATE does not start." |
| else |
| do_cmd "mt76-test ${interface} set state=off" |
| do_cmd "iw dev mon${phy_idx} del" |
| |
| if [ $phy_idx -ge $SOC_start_idx ]; then |
| local end_idx=$SOC_end_idx |
| local start_idx=$SOC_start_idx |
| else |
| local end_idx=$((SOC_start_idx-1)) |
| local start_idx="0" |
| fi |
| |
| # first check its phy and dbdc band phy has monitor interface or not |
| # if has at lease one mon interface, then skip adding back normal interface |
| local has_mon="0" |
| for phy_index in $( seq $start_idx $end_idx ) |
| do |
| # "phy#-1" would not be in iw dev, therefore it will grep the line from the phy#${phy_index} to the end |
| local prev_phy_index=$((phy_index-1)) |
| local has_mon_phy=$(iw dev | awk "/phy#${phy_index}/,/phy#${prev_phy_index}/" | grep "Interface mon") |
| # if this phy interface has mon interface |
| if [ ! -z "${has_mon_phy}" ]; then |
| local has_mon="1" |
| fi |
| done |
| |
| for phy_index in $( seq $start_idx $end_idx ) |
| do |
| # "phy#-1" would not be in iw dev, therefore it will grep the line from the phy#${phy_index} to the end |
| local prev_phy_index=$((phy_index-1)) |
| local j="1" |
| local add_if_num=$(get_config "DEL_IF${phy_index}_NUM" ${interface_file}) |
| if [ -z "${add_if_num}" ]; then |
| local add_if_num="0" |
| fi |
| # if this phy interface (including its dbdc phy) has no mon interface and can find deleted interface in file, then add it back |
| if [ "${has_mon}" == "0" ] && [ $add_if_num -ge "1" ]; then |
| local if_index=$add_if_num |
| # add interface backwards |
| while [ $if_index -gt "0" ] |
| do |
| local add_if=$(get_config "DEL_IF${phy_index}-${if_index}" ${interface_file}) |
| do_cmd "iw phy phy${phy_index} interface add ${add_if} type managed" |
| # remove the deleted interface in interface_file since it is added back |
| sed -i "/DEL_IF${phy_index}-${if_index}=/d" ${interface_file} |
| if_index=$((if_index-1)) |
| done |
| # remove the number of deleted interface in interface_file since it is all added back |
| sed -i "/DEL_IF${phy_index}_NUM=/d" ${interface_file} |
| fi |
| done |
| |
| do_cmd "mt76-test ${interface} set aid=0" |
| fi |
| |
| if [ ${phy_idx} -lt ${SOC_start_idx} ]; then |
| sed -i '/_PCIE=/d' ${iwpriv_file} |
| elif [ ${phy_idx} -ge ${SOC_start_idx} ]; then |
| sed -i '/_SOC=/d' ${iwpriv_file} |
| fi |
| ;; |
| "TXCOMMIT") |
| do_cmd "mt76-test ${interface} set aid=1" |
| ;; |
| "TXFRAME") |
| do_cmd "mt76-test ${interface} set state=tx_frames" |
| ;; |
| "TXSTOP"|"RXSTOP") |
| do_cmd "mt76-test ${interface} set state=idle" |
| ;; |
| "TXREVERT") |
| do_cmd "mt76-test ${interface} set aid=0" |
| ;; |
| "RXFRAME") |
| do_cmd "mt76-test ${interface} set state=rx_frames" |
| ;; |
| "TXCONT") |
| do_cmd "mt76-test ${interface} set state=tx_cont" |
| ;; |
| "GROUPREK") |
| do_cmd "mt76-test ${interface} set state=group_prek" |
| do_cmd "atenl -i ${interface} -c \"eeprom precal sync group\"" |
| ;; |
| "GROUPREKDump") |
| do_cmd "mt76-test ${interface} set state=group_prek_dump" |
| ;; |
| "GROUPREKClean") |
| do_cmd "mt76-test ${interface} set state=group_prek_clean" |
| do_cmd "atenl -i ${interface} -c \"eeprom precal group clean\"" |
| ;; |
| "DPD2G") |
| do_cmd "mt76-test ${interface} set state=dpd_2g" |
| do_cmd "atenl -i ${interface} -c \"eeprom precal sync dpd 2g\"" |
| ;; |
| "DPD5G") |
| do_cmd "mt76-test ${interface} set state=dpd_5g" |
| do_cmd "atenl -i ${interface} -c \"eeprom precal sync dpd 5g\"" |
| ;; |
| "DPD6G") |
| do_cmd "mt76-test ${interface} set state=dpd_6g" |
| do_cmd "atenl -i ${interface} -c \"eeprom precal sync dpd 6g\"" |
| ;; |
| "DPDDump") |
| do_cmd "mt76-test ${interface} set state=dpd_dump" |
| ;; |
| "DPDClean") |
| do_cmd "mt76-test ${interface} set state=dpd_clean" |
| do_cmd "atenl -i ${interface} -c \"eeprom precal dpd clean\"" |
| ;; |
| *) |
| print_debug "skip ${ate_cmd}" |
| ;; |
| esac |
| } |
| |
| function dump_usage { |
| echo "Usage:" |
| echo " mwctl <interface> set csi ctrl=<opt1>,<opt2>,<opt3>,<opt4> (macaddr=<macaddr>)" |
| echo " mwctl <interface> set csi interval=<interval (us)>" |
| echo " mwctl <interface> dump csi <packet num> <filename>" |
| echo " mwctl <interface> set amnt <index>(0x0~0xf) <mac addr>(xx:xx:xx:xx:xx:xx)" |
| echo " mwctl <interface> dump amnt <index> (0x0~0xf or 0xff)" |
| echo " mwctl <interface> set ap_rfeatures he_gi=<val>" |
| echo " mwctl <interface> set ap_rfeatures he_ltf=<val>" |
| echo " mwctl <interface> set ap_rfeatures trig_type=<enable>,<val> (val: 0-7)" |
| echo " mwctl <interface> set ap_rfeatures ack_policy=<val> (val: 0-4)" |
| echo " mwctl <interface> set ap_wireless fixed_mcs=<val>" |
| echo " mwctl <interface> set ap_wireless ofdma=<val> (0: disable, 1: DL, 2: UL)" |
| echo " mwctl <interface> set ap_wireless nusers_ofdma=<val>" |
| echo " mwctl <interface> set ap_wireless ppdu_type=<val> (0: SU, 1: MU, 4: LEGACY)" |
| echo " mwctl <interface> set ap_wireless add_ba_req_bufsize=<val>" |
| echo " mwctl <interface> set ap_wireless mimo=<val> (0: DL, 1: UL)" |
| echo " mwctl <interface> set ap_wireless ampdu=<enable>" |
| echo " mwctl <interface> set ap_wireless amsdu=<enable>" |
| echo " mwctl <interface> set ap_wireless cert=<enable>" |
| echo " mwctl <interface> set mu onoff=<val> (bitmap- UL MU-MIMO(bit3), DL MU-MIMO(bit2), UL OFDMA(bit1), DL OFDMA(bit0))" |
| echo " mwctl <interface> dump phy_capa" |
| } |
| |
| function register_handler { |
| |
| local phy_idx=$1 |
| local offset=$2 |
| local val=$3 |
| local cmd=$4 |
| local w_cmd="write" |
| |
| regidx=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/regidx |
| regval=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/regval |
| |
| echo ${offset} > ${regidx} |
| if [[ "${cmd}" == "${w_cmd}" ]]; then |
| echo ${val} > ${regval} |
| fi |
| |
| res=$(cat ${regval} | cut -d 'x' -f 2) |
| printf "%s mac:[%s]:%s\n" ${interface_ori} ${offset} ${res} |
| } |
| |
| # main start here |
| parse_sku |
| if [ -z ${interface} ]; then |
| dump_usage |
| exit |
| elif [[ ${interface} == "ra"* ]]; then |
| convert_interface $interface |
| elif [[ ${interface} == "phy" ]]; then |
| # handle mwctl phy phy0 e2p ... case |
| interface=$2 |
| cmd_type=$3 |
| full_cmd=$4 |
| fi |
| |
| tmp_work_mode=$(get_config "WORKMODE" ${iwpriv_file}) |
| |
| if [ ! -z ${tmp_work_mode} ]; then |
| work_mode=${tmp_work_mode} |
| fi |
| |
| cmd=$(echo ${full_cmd} | sed s/=/' '/g | cut -d " " -f 1) |
| param=$(echo ${full_cmd} | sed s/=/' '/g | cut -d " " -f 2) |
| |
| if [ "${cmd_type}" = "set" ]; then |
| skip=0 |
| case ${cmd} in |
| ## In wifi 7 chipset, testmode & vendor command both use mwctl |
| ## Therefore this wrapper would translate it to either mt76-test or mt76-vendor based on the attribute of the command |
| ## Translate to mt76-vendor command |
| "csi"|"amnt"|"ap_rfeatures"|"ap_wireless"|"mu"|"set_muru_manual_config") |
| if [ ${is_connac3} == "1" ]; then |
| hostapd_cmd="$(echo $* | sed 's/set/raw/')" |
| do_cmd "hostapd_cli -i $hostapd_cmd" |
| else |
| do_cmd "mt76-vendor $*" |
| fi |
| skip=1 |
| ;; |
| "ATE") |
| do_ate_work ${param} |
| |
| skip=1 |
| ;; |
| "ATETXCNT"|"ATETXLEN"|"ATETXMCS"|"ATEVHTNSS"|"ATETXLDPC"|"ATETXSTBC"| \ |
| "ATEPKTTXTIME"|"ATEIPG"|"ATEDUTYCYCLE"|"ATETXFREQOFFSET") |
| cmd_new=$(simple_convert ${cmd}) |
| if [ "${param_new}" = "undefined" ]; then |
| echo "unknown cmd: ${cmd}" |
| exit |
| fi |
| param_new=${param} |
| if [ "${cmd}" = "ATETXCNT" ] && [ "${param}" = "0" ]; then |
| param_new="0xFFFFFFFF" |
| fi |
| ;; |
| "ATETXANT"|"ATERXANT") |
| cmd_new="tx_antenna" |
| param_new=${param} |
| ;; |
| "ATETXGI") |
| if [ ${is_connac3} == "0" ]; then |
| tx_mode=$(convert_tx_mode $(get_config "ATETXMODE" ${iwpriv_file})) |
| convert_gi ${tx_mode} ${param} |
| skip=1 |
| else |
| cmd_new="tx_rate_sgi" |
| param_new=${param} |
| fi |
| ;; |
| "ATETXMODE") |
| cmd_new="tx_rate_mode" |
| param_new=$(convert_tx_mode ${param}) |
| if [ "${param_new}" = "undefined" ]; then |
| echo "unknown tx mode" |
| echo "0:cck, 1:ofdm, 2:ht, 4:vht, 8:he_su, 9:he_er, 10:he_tb, 11:he_mu" |
| exit |
| else |
| record_config ${cmd} ${param} ${iwpriv_file} |
| fi |
| ;; |
| "ATETXPOW0"|"ATETXPOW1"|"ATETXPOW2"|"ATETXPOW3"|"ATETXPOW") |
| cmd_new="tx_power" |
| if [ "${param}" == "127" ]; then |
| # for iTest verification |
| exit |
| fi |
| param_new="${param},0,0,0" |
| ;; |
| "ATEMUAID") |
| cmd_new="aid" |
| param_new=${param} |
| ;; |
| "ATETXBW") |
| record_config ${cmd} ${param} ${iwpriv_file} |
| skip=1 |
| ;; |
| "ATECHANNEL") |
| convert_channel ${param} |
| skip=1 |
| ;; |
| "ATERXSTAT") |
| convert_rxstat |
| skip=1 |
| ;; |
| "ATECTRLBANDIDX") |
| change_band_idx ${param} |
| skip=1 |
| ;; |
| "ATEDA"|"ATESA"|"ATEBSSID") |
| set_mac_addr ${cmd} ${param} |
| skip=1 |
| ;; |
| "DfsRxCtrl"|"DfsRxHist") |
| convert_dfs ${cmd} ${param} |
| skip=1 |
| ;; |
| "ATETxBfInit"|"ATETxBfGdInit"|"ATEIBFPhaseComp"|"ATEEBfProfileConfig"|"ATEIBfProfileConfig"| \ |
| "TxBfTxApply"|"ATETxPacketWithBf"|"TxBfProfileData20MAllWrite"|"ATEIBfInstCal"| \ |
| "ATEIBfGdCal"|"ATEIBFPhaseE2pUpdate"|"TriggerSounding"|"StopSounding"|"TxBfTxCmd"| \ |
| "StaRecBfRead"|"TxBfProfileTagInValid"|"TxBfProfileTagWrite"|"TxBfProfileTagRead"| \ |
| "ATEIBFPhaseVerify"|"ATEConTxETxBfGdProc"|"ATEConTxETxBfInitProc") |
| convert_ibf ${cmd} ${param} |
| skip=1 |
| ;; |
| "bufferMode") |
| if [ "${param}" = "2" ]; then |
| do_cmd "atenl -i ${interface} -c \"eeprom update buffermode\"" |
| fi |
| skip=1 |
| ;; |
| "ResetCounter"|"ATERXSTATRESET") |
| skip=1 |
| ;; |
| "WORKMODE") |
| record_config "WORKMODE" ${param} ${iwpriv_file} |
| echo "Entering ${param} mode in iwpriv" |
| skip=1 |
| ;; |
| "ATERUINFO") |
| convert_ruinfo ${param} |
| skip=1 |
| ;; |
| *) |
| print_debug "Unknown command to set: ${cmd}" |
| skip=1 |
| esac |
| |
| if [ "${skip}" != "1" ]; then |
| do_cmd "mt76-test ${interface} set ${cmd_new}=${param_new}" |
| fi |
| |
| elif [ "${cmd_type}" = "show" ]; then |
| if [ "${cmd}" = "wtbl" ]; then |
| wlan_idx=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/wlan_idx |
| wtbl_info=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/wtbl_info |
| |
| do_cmd "echo ${param} > ${wlan_idx}" |
| do_cmd "cat ${wtbl_info}" |
| elif [ "${cmd}" = "ATERXSTAT" ]; then |
| convert_rxstat |
| else |
| do_cmd "mt76-test ${interface} dump" |
| do_cmd "mt76-test ${interface} dump stats" |
| fi |
| |
| elif [ "${cmd_type}" = "e2p" ]; then |
| # support multiple read write |
| # eeprom offset write |
| if [[ ${full_cmd} == *"="* ]]; then |
| IFS=, |
| for tuple in $full_cmd |
| do |
| cmd=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 1) |
| param=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 2) |
| offset=$(printf "0x%s" ${cmd}) |
| val=$(printf "0x%s" ${param}) |
| tmp=$((${val} & 0xff)) |
| tmp=$(printf "0x%x" ${tmp}) |
| do_cmd "atenl -i ${interface} -c \"eeprom set ${offset}=${tmp}\"" |
| |
| offset=$((${offset})) |
| offset=$(expr ${offset} + "1") |
| offset=$(printf "0x%x" ${offset}) |
| tmp=$(((${val} >> 8) & 0xff)) |
| tmp=$(printf "0x%x" ${tmp}) |
| do_cmd "atenl -i ${interface} -c \"eeprom set ${offset}=${tmp}\"" |
| done |
| else |
| IFS=, |
| for tuple in $full_cmd |
| do |
| cmd=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 1) |
| param=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 2) |
| offset=$(printf "0x%s" ${cmd}) |
| val=$(printf "0x%s" ${param}) |
| v1=$(do_cmd "atenl -i ${interface} -c \"eeprom read ${param}\"") |
| v1=$(echo "${v1}" | grep "val =" | cut -d '(' -f 2 | grep -o -E '[0-9]+') |
| |
| tmp=$(printf "0x%s" ${param}) |
| tmp=$((${tmp})) |
| param2=$(expr ${tmp} + "1") |
| param2=$(printf "%x" ${param2}) |
| v2=$(do_cmd "atenl -i ${interface} -c \"eeprom read ${param2}\"") |
| v2=$(echo "${v2}" | grep "val =" | cut -d '(' -f 2 | grep -o -E '[0-9]+') |
| |
| param=$(printf "0x%s" ${param}) |
| param=$(printf "%04x" ${param}) |
| param=$(echo $param | tr 'a-z' 'A-Z') |
| printf "%s e2p:\n" ${interface_ori} |
| printf "[0x%s]:0x%02x%02x\n" ${param} ${v2} ${v1} |
| done |
| fi |
| |
| elif [ "${cmd_type}" = "mac" ]; then |
| offset=$(printf "0x%s" ${cmd}) |
| val=$(printf "0x%s" ${param}) |
| |
| # reg write |
| if [[ ${full_cmd} == *"="* ]]; then |
| register_handler ${phy_idx} ${offset} ${val} "write" |
| else |
| start_addr=$(echo ${full_cmd} | sed s/-/' '/g | cut -d " " -f 1) |
| end_addr=$(echo ${full_cmd} | sed s/-/' '/g | cut -d " " -f 2) |
| loop=$((0x${end_addr}-0x${start_addr})) |
| |
| if [[ ${loop} == "0" ]]; then |
| register_handler ${phy_idx} ${offset} ${val} |
| else |
| i=0 |
| while [ $i -le $loop ]; do |
| addr=$((0x${start_addr}+$i)) |
| offset=$(printf "0x%x" ${addr}) |
| register_handler ${phy_idx} ${offset} ${val} |
| i=$(($i + 4)) |
| done |
| fi |
| fi |
| |
| ## dump command is only for vendor commands |
| elif [ "${cmd_type}" = "dump" ]; then |
| do_cmd "mt76-vendor $*" |
| elif [ "${cmd_type}" = "switch" ]; then |
| eeprom_mode_file=/sys/kernel/debug/ieee80211/phy0/mt76/eeprom_mode |
| eeprom_mode=$(cat ${eeprom_mode_file} | grep "mode" | sed -n 2p | cut -d " " -f 4) |
| eeprom_testmode_offset="1af" |
| testmode_enable="0" |
| |
| if [ ${is_connac3} == "0" ]; then |
| return |
| fi |
| |
| if [ "${cmd}" = "testmode" ]; then |
| testmode_enable="1" |
| do_cmd "wifi down" |
| do_cmd "uci set wireless.radio0.disabled=1" |
| do_cmd "uci set wireless.radio1.disabled=1" |
| do_cmd "uci set wireless.radio2.disabled=1" |
| do_cmd "uci commit" |
| fi |
| |
| if [ "${eeprom_mode}" = "flash" ]; then |
| ## flash mode should set eeprom testmode offset bit |
| ## efuse/bin file/default bin mode rely on module param only |
| do_cmd "atenl -i ${interface} -c \"eeprom set 0x${eeprom_testmode_offset}=0x${testmode_enable}\"" |
| ## If has no precal, it would not affect |
| do_cmd "atenl -i ${interface} -c \"eeprom precal sync\"" |
| do_cmd "atenl -i ${interface} -c \"sync eeprom all\"" |
| fi |
| |
| do_cmd "rmmod mt7996e" |
| do_cmd "rmmod mt76-connac-lib" |
| do_cmd "rmmod mt76" |
| do_cmd "rmmod mac80211" |
| do_cmd "rmmod cfg80211" |
| do_cmd "rmmod compat" |
| do_cmd "insmod compat" |
| do_cmd "insmod cfg80211" |
| do_cmd "insmod mac80211" |
| do_cmd "insmod mt76" |
| do_cmd "insmod mt76-connac-lib" |
| do_cmd "insmod mt7996e testmode_enable=${testmode_enable}" |
| do_cmd "sleep 5" |
| do_cmd "killall hostapd" |
| do_cmd "killall netifd" |
| else |
| echo "Unknown command" |
| fi |