blob: b5b6fa347ab00c746b220fb92aa4084d7c603055 [file] [log] [blame]
#!/bin/ash
interface=$1 # phy0/phy1/ra0
cmd_type=$2 # set/show/e2p/mac/dump
full_cmd=$3
interface_ori=${interface}
SOC_start_idx="0"
SOC_end_idx="0"
is_eagle="0"
work_mode="RUN" # RUN/PRINT/DEBUG
iwpriv_file="/tmp/iwpriv_wrapper"
interface_file="/tmp/interface"
phy_idx=$(echo ${interface} | tr -dc '0-9')
function do_cmd() {
case ${work_mode} in
"RUN")
eval "$1"
;;
"PRINT")
echo "$1"
;;
"DEBUG")
echo "$1"
eval "$1"
;;
esac
}
function print_debug() {
if [ "${work_mode}" = "DEBUG" ]; then
echo "$1"
fi
}
function write_dmesg() {
echo "$1" > /dev/kmsg
}
function record_config() {
local config=$1
local tmp_file=$3
# check it is SOC(mt7986)/Eagle or PCIE card (mt7915/7916), and write its config
if [ ${tmp_file} != ${interface_file} ]; then
if [ $phy_idx -lt $SOC_start_idx ]; then
config="${config}_PCIE"
elif [ $phy_idx -ge $SOC_start_idx ]; then
config="${config}_SOC"
fi
fi
if [ -f ${tmp_file} ]; then
if grep -q ${config} ${tmp_file}; then
sed -i "/${config}/c\\${config}=$2" ${tmp_file}
else
echo "${config}=$2" >> ${tmp_file}
fi
else
echo "${config}=$2" >> ${tmp_file}
fi
}
function get_config() {
local config=$1
local tmp_file=$2
if [ ! -f ${tmp_file} ]; then
echo ""
return
fi
# check it is SOC(mt7986)/Eagle or PCIE card (mt7915/7916), and write its config
if [ ${tmp_file} != ${interface_file} ]; then
if [ $phy_idx -lt $SOC_start_idx ]; then
config="${config}_PCIE"
elif [ $phy_idx -ge $SOC_start_idx ]; then
config="${config}_SOC"
fi
fi
if grep -q ${config} ${tmp_file}; then
echo "$(cat ${tmp_file} | grep ${config} | sed s/=/' '/g | cut -d " " -f 2)"
else
echo ""
fi
}
function parse_sku {
SOC_start_idx=$(get_config "STARTIDX" ${interface_file})
SOC_end_idx=$(get_config "ENDIDX" ${interface_file})
is_eagle=$(get_config "IS_EAGLE" ${interface_file})
local eeprom_file=/sys/kernel/debug/ieee80211/phy0/mt76/eeprom
if [ -z "${SOC_start_idx}" ] || [ -z "${SOC_end_idx}" ] || [ -z "${is_eagle}" ]; then
if [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7916")" ]; then
SOC_start_idx="2"
SOC_end_idx="3"
is_eagle="0"
elif [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7915")" ]; then
SOC_start_idx="1"
SOC_end_idx="2"
is_eagle="0"
elif [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7986")" ]; then
SOC_start_idx="0"
SOC_end_idx="1"
is_eagle="0"
elif [ ! -z "$(head -c 2 ${eeprom_file} | hexdump | grep "7990")" ]; then
SOC_start_idx="0"
SOC_end_idx="2"
is_eagle="1"
else
echo "Interface Conversion Failed!"
echo "Please use iwpriv <phy0/phy1/..> set <...> or configure the sku of your board manually by the following commands"
echo "For AX6000:"
echo " echo STARTIDX=0 >> ${interface_file}"
echo " echo ENDIDX=1 >> ${interface_file}"
echo " echo IS_EAGLE=0 >> ${interface_file}"
echo "For AX7800:"
echo " echo STARTIDX=2 >> ${interface_file}"
echo " echo ENDIDX=3 >> ${interface_file}"
echo " echo IS_EAGLE=0 >> ${interface_file}"
echo "For AX8400:"
echo " echo STARTIDX=1 >> ${interface_file}"
echo " echo ENDIDX=2 >> ${interface_file}"
echo " echo IS_EAGLE=0 >> ${interface_file}"
echo "For Eagle:"
echo " echo STARTIDX=1 >> ${interface_file}"
echo " echo ENDIDX=2 >> ${interface_file}"
echo " echo IS_EAGLE=1 >> ${interface_file}"
exit 0
fi
record_config "STARTIDX" ${SOC_start_idx} ${interface_file}
record_config "ENDIDX" ${SOC_end_idx} ${interface_file}
record_config "IS_EAGLE" ${is_eagle} ${interface_file}
fi
}
function convert_interface {
if [ ${is_eagle} == "0" ]; then
if [[ $1 == "raix"* ]]; then
phy_idx=1
elif [[ $1 == "rai"* ]]; then
phy_idx=0
elif [[ $1 == "rax"* ]]; then
phy_idx=$((SOC_start_idx+1))
else
phy_idx=$SOC_start_idx
fi
# convert phy index according to band idx
local band_idx=$(get_config "ATECTRLBANDIDX" ${iwpriv_file})
if [ "${band_idx}" = "0" ]; then
if [[ $1 == "raix"* ]]; then
phy_idx=0
elif [[ $1 == "rax"* ]]; then
phy_idx=$SOC_start_idx
fi
elif [ "${band_idx}" = "1" ]; then
if [[ $1 == "rai"* ]]; then
# AX8400: mt7915 remain phy0
# AX7800: mt7916 becomes phy1
phy_idx=$((SOC_start_idx-1))
elif [[ $1 == "ra"* ]]; then
phy_idx=$((SOC_start_idx+1))
fi
fi
else
# Eagle has different mapping method
# phy0: ra0
# phy1: rai0
# phy2: rax0
if [[ $1 == "rai"* ]]; then
phy_idx=1
elif [[ $1 == "rax"* ]]; then
phy_idx=2
else
phy_idx=0
fi
fi
interface="phy${phy_idx}"
}
function change_band_idx {
local new_idx=$1
local new_phy_idx=$phy_idx
local old_idx=$(get_config "ATECTRLBANDIDX" ${iwpriv_file})
if [[ ${interface_ori} == "ra"* ]]; then
if [ -z "${old_idx}" ] || [ "${old_idx}" != "${new_idx}" ]; then
if [ "${new_idx}" = "0" ]; then
# raix0 & rai0 becomes rai0
if [[ $interface_ori == "rai"* ]]; then
new_phy_idx=0
# rax0 & ra0 becomes ra0
elif [[ $interface_ori == "ra"* ]]; then
new_phy_idx=$SOC_start_idx
fi
elif [ "${new_idx}" = "1" ]; then
# raix0 & rai0 becomes raix0
if [[ $interface_ori == "rai"* ]]; then
# For AX8400 => don't change phy idx
if [ ${SOC_start_idx} != "1" ]; then
new_phy_idx=1
fi
# rax0 & ra0 becomes rax0
elif [[ $interface_ori == "ra"* ]]; then
new_phy_idx=$((SOC_start_idx+1))
fi
fi
fi
if [ ${new_phy_idx} != ${phy_idx} ]; then
do_ate_work "ATESTOP"
phy_idx=$new_phy_idx
interface="phy${phy_idx}"
do_ate_work "ATESTART"
fi
fi
record_config "ATECTRLBANDIDX" ${new_idx} ${iwpriv_file}
}
function simple_convert() {
if [ "$1" = "ATETXCNT" ]; then
echo "tx_count"
elif [ "$1" = "ATETXLEN" ]; then
echo "tx_length"
elif [ "$1" = "ATETXMCS" ]; then
echo "tx_rate_idx"
elif [ "$1" = "ATEVHTNSS" ]; then
echo "tx_rate_nss"
elif [ "$1" = "ATETXLDPC" ]; then
echo "tx_rate_ldpc"
elif [ "$1" = "ATETXSTBC" ]; then
echo "tx_rate_stbc"
elif [ "$1" = "ATEPKTTXTIME" ]; then
echo "tx_time"
elif [ "$1" = "ATEIPG" ]; then
echo "tx_ipg"
elif [ "$1" = "ATEDUTYCYCLE" ]; then
echo "tx_duty_cycle"
elif [ "$1" = "ATETXFREQOFFSET" ]; then
echo "freq_offset"
else
echo "undefined"
fi
}
function convert_tx_mode() {
# Remove leading zeros
local tx_mode=$(echo $1 | sed -r 's/0+([0-9]+)/\1/g')
if [ "$tx_mode" = "0" ]; then
echo "cck"
elif [ "$tx_mode" = "1" ]; then
echo "ofdm"
elif [ "$tx_mode" = "2" ]; then
echo "ht"
elif [ "$tx_mode" = "4" ]; then
echo "vht"
elif [ "$tx_mode" = "8" ]; then
echo "he_su"
elif [ "$tx_mode" = "9" ]; then
echo "he_er"
elif [ "$tx_mode" = "10" ]; then
echo "he_tb"
elif [ "$tx_mode" = "11" ]; then
echo "he_mu"
elif [ "$tx_mode" = "13" ]; then
echo "eht_su"
elif [ "$tx_mode" = "14" ]; then
echo "eht_tb"
elif [ "$tx_mode" = "15" ]; then
echo "eht_mu"
else
echo "undefined"
fi
}
function convert_gi {
local tx_mode=$1
local val=$2
local sgi="0"
local he_ltf="0"
case ${tx_mode} in
"ht"|"vht")
sgi=${val}
;;
"he_su"|"he_er")
case ${val} in
"0")
;;
"1")
he_ltf="1"
;;
"2")
sgi="1"
he_ltf="1"
;;
"3")
sgi="2"
he_ltf="2"
;;
"4")
he_ltf="2"
;;
*)
echo "unknown gi"
esac
;;
"he_mu")
case ${val} in
"0")
he_ltf="2"
;;
"1")
he_ltf="1"
;;
"2")
sgi="1"
he_ltf="1"
;;
"3")
sgi="2"
he_ltf="2"
;;
*)
echo "unknown gi"
esac
;;
"he_tb")
case ${val} in
"0")
sgi="1"
;;
"1")
sgi="1"
he_ltf="1"
;;
"2")
sgi="2"
he_ltf="2"
;;
*)
echo "unknown gi"
esac
;;
*)
print_debug "legacy mode no need gi"
esac
do_cmd "mt76-test ${interface} set tx_rate_sgi=${sgi} tx_ltf=${he_ltf}"
}
function convert_channel {
local ctrl_band_idx=$(get_config "ATECTRLBANDIDX" ${iwpriv_file})
local ch=$(echo $1 | sed s/:/' '/g | cut -d " " -f 1)
local bw=$(get_config "ATETXBW" ${iwpriv_file} | cut -d ":" -f 1)
local bw_str="HT20"
local base_chan=1
local control_freq=0
local base_freq=0
local band=$(echo $1 | sed s/:/' '/g | cut -d " " -f 2)
local temp=$((phy_idx+1))
# Handle ATECTRLBANDIDX
if [ ! -z ${ctrl_band_idx} ]; then
if [ "${ctrl_band_idx}" == "1" ] && [ ${band} == "0" ]; then
local temp=$(cat "/etc/config/wireless"| grep "option band" | sed -n ${temp}p | cut -c 15)
if [ "${temp}" == "2" ]; then
local band=0
elif [ "${temp}" == "5" ]; then
local band=1
elif [ "${temp}" == "6" ]; then
local band=2
else
echo "iwpriv wrapper band translate error!"
fi
else
# mt7915 in AX8400 case: band should be determined by only the input band
if [ "${SOC_start_idx}" == "1" ] && [ ${phy_idx} == "0" ]; then
local band=$((band))
else
local band=$((ctrl_band_idx * band))
fi
fi
fi
if [[ $1 != *":"* ]] || [ "${band}" = "0" ]; then
case ${bw} in
"1")
if [ "${ch}" -lt "3" ] || [ "${ch}" -gt "12" ]; then
local bw_str="HT20"
else
local bw_str="HT40+"
ch=$(expr ${ch} - "2")
fi
;;
esac
local base_freq=2412
elif [ "${band}" = "1" ]; then
case ${bw} in
"5")
bw_str="160MHz"
if [ ${ch} -lt "68" ]; then
ch="36"
elif [ ${ch} -lt "100" ]; then
ch="68"
elif [ ${ch} -lt "132" ]; then
ch="100"
elif [ ${ch} -lt "181" ]; then
ch="149"
fi
;;
"2")
bw_str="80MHz"
if [ ${ch} -lt "52" ]; then
ch="36"
elif [ ${ch} -lt "68" ]; then
ch="52"
elif [ ${ch} -lt "84" ]; then
ch="68"
elif [ ${ch} -lt "100" ]; then
ch="84"
elif [ ${ch} -lt "116" ]; then
ch="100"
elif [ ${ch} -lt "132" ]; then
ch="116"
elif [ ${ch} -lt "149" ]; then
ch="132"
elif [ ${ch} -lt "165" ]; then
ch="149"
elif [ ${ch} -lt "181" ]; then
ch="165"
fi
;;
"1")
if [ ${ch} -lt "44" ]; then
ch=$([ "${ch}" -lt "40" ] && echo "36" || echo "40")
bw_str=$([ "${ch}" -le "38" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "52" ]; then
ch=$([ "${ch}" -lt "48" ] && echo "44" || echo "48")
bw_str=$([ "${ch}" -le "46" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "60" ]; then
ch=$([ "${ch}" -lt "56" ] && echo "52" || echo "56")
bw_str=$([ "${ch}" -le "54" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "68" ]; then
ch=$([ "${ch}" -lt "64" ] && echo "60" || echo "64")
bw_str=$([ "${ch}" -le "62" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "76" ]; then
ch=$([ "${ch}" -lt "72" ] && echo "68" || echo "72")
bw_str=$([ "${ch}" -le "70" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "84" ]; then
ch=$([ "${ch}" -lt "80" ] && echo "76" || echo "80")
bw_str=$([ "${ch}" -le "78" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "92" ]; then
ch=$([ "${ch}" -lt "88" ] && echo "84" || echo "88")
bw_str=$([ "${ch}" -le "86" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "100" ]; then
ch=$([ "${ch}" -lt "96" ] && echo "92" || echo "96")
bw_str=$([ "${ch}" -le "94" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "108" ]; then
ch=$([ "${ch}" -lt "104" ] && echo "100" || echo "104")
bw_str=$([ "${ch}" -le "102" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "116" ]; then
ch=$([ "${ch}" -lt "112" ] && echo "108" || echo "112")
bw_str=$([ "${ch}" -le "110" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "124" ]; then
ch=$([ "${ch}" -lt "120" ] && echo "116" || echo "120")
bw_str=$([ "${ch}" -le "118" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "132" ]; then
ch=$([ "${ch}" -lt "128" ] && echo "124" || echo "128")
bw_str=$([ "${ch}" -le "126" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "140" ]; then
ch=$([ "${ch}" -lt "136" ] && echo "132" || echo "136")
bw_str=$([ "${ch}" -le "134" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "149" ]; then
ch=$([ "${ch}" -lt "144" ] && echo "140" || echo "144")
bw_str=$([ "${ch}" -le "142" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "157" ]; then
ch=$([ "${ch}" -lt "153" ] && echo "149" || echo "153")
bw_str=$([ "${ch}" -le "151" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "165" ]; then
ch=$([ "${ch}" -lt "161" ] && echo "157" || echo "161")
bw_str=$([ "${ch}" -le "159" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "173" ]; then
ch=$([ "${ch}" -lt "169" ] && echo "165" || echo "169")
bw_str=$([ "${ch}" -le "167" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "181" ]; then
ch=$([ "${ch}" -lt "177" ] && echo "173" || echo "177")
bw_str=$([ "${ch}" -le "175" ] && echo "HT40+" || echo "HT40-")
fi
;;
"0")
local bw_str="HT20"
;;
esac
local base_freq=5180
local base_chan=36
else
local base_freq=5955
case ${bw} in
"12")
local bw_str="320"
if [ ${ch} == "31" ]; then
local control_freq="5955"
elif [ ${ch} == "63" ]; then
local control_freq="6115"
elif [ ${ch} == "95" ]; then
local control_freq="6275"
elif [ ${ch} == "127" ]; then
local control_freq="6435"
elif [ ${ch} == "159" ]; then
local control_freq="6595"
elif [ ${ch} == "191" ]; then
local control_freq="6755"
fi
local center_freq=$(((ch - base_chan) * 5 + base_freq))
do_cmd "iw dev mon${phy_idx} set freq ${control_freq} ${bw_str} ${center_freq}"
return
;;
"5")
bw_str="160MHz"
if [ ${ch} -lt "33" ]; then
ch="1"
elif [ ${ch} -lt "65" ]; then
ch="33"
elif [ ${ch} -lt "97" ]; then
ch="65"
elif [ ${ch} -lt "129" ]; then
ch="97"
elif [ ${ch} -lt "161" ]; then
ch="129"
elif [ ${ch} -lt "193" ]; then
ch="161"
elif [ ${ch} -lt "225" ]; then
ch="193"
fi
;;
"2")
bw_str="80MHz"
if [ ${ch} -lt "17" ]; then
ch="1"
elif [ ${ch} -lt "33" ]; then
ch="17"
elif [ ${ch} -lt "49" ]; then
ch="33"
elif [ ${ch} -lt "65" ]; then
ch="49"
elif [ ${ch} -lt "81" ]; then
ch="65"
elif [ ${ch} -lt "97" ]; then
ch="81"
elif [ ${ch} -lt "113" ]; then
ch="97"
elif [ ${ch} -lt "129" ]; then
ch="113"
elif [ ${ch} -lt "145" ]; then
ch="129"
elif [ ${ch} -lt "161" ]; then
ch="145"
elif [ ${ch} -lt "177" ]; then
ch="161"
elif [ ${ch} -lt "193" ]; then
ch="177"
elif [ ${ch} -lt "209" ]; then
ch="193"
elif [ ${ch} -lt "225" ]; then
ch="209"
fi
;;
"1")
if [ ${ch} -lt "9" ]; then
ch=$([ "${ch}" -lt "5" ] && echo "1" || echo "5")
bw_str=$([ "${ch}" -le "3" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "17" ]; then
ch=$([ "${ch}" -lt "13" ] && echo "9" || echo "13")
bw_str=$([ "${ch}" -le "11" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "25" ]; then
ch=$([ "${ch}" -lt "21" ] && echo "17" || echo "21")
bw_str=$([ "${ch}" -le "19" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "33" ]; then
ch=$([ "${ch}" -lt "29" ] && echo "25" || echo "29")
bw_str=$([ "${ch}" -le "27" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "33" ]; then
ch=$([ "${ch}" -lt "29" ] && echo "25" || echo "29")
bw_str=$([ "${ch}" -le "27" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "41" ]; then
ch=$([ "${ch}" -lt "37" ] && echo "33" || echo "37")
bw_str=$([ "${ch}" -le "35" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "49" ]; then
ch=$([ "${ch}" -lt "45" ] && echo "41" || echo "45")
bw_str=$([ "${ch}" -le "43" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "57" ]; then
ch=$([ "${ch}" -lt "53" ] && echo "49" || echo "53")
bw_str=$([ "${ch}" -le "51" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "65" ]; then
ch=$([ "${ch}" -lt "61" ] && echo "57" || echo "61")
bw_str=$([ "${ch}" -le "59" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "73" ]; then
ch=$([ "${ch}" -lt "69" ] && echo "65" || echo "69")
bw_str=$([ "${ch}" -le "67" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "81" ]; then
ch=$([ "${ch}" -lt "77" ] && echo "73" || echo "77")
bw_str=$([ "${ch}" -le "75" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "89" ]; then
ch=$([ "${ch}" -lt "85" ] && echo "81" || echo "85")
bw_str=$([ "${ch}" -le "83" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "97" ]; then
ch=$([ "${ch}" -lt "93" ] && echo "89" || echo "93")
bw_str=$([ "${ch}" -le "91" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "105" ]; then
ch=$([ "${ch}" -lt "101" ] && echo "97" || echo "101")
bw_str=$([ "${ch}" -le "99" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "113" ]; then
ch=$([ "${ch}" -lt "109" ] && echo "105" || echo "109")
bw_str=$([ "${ch}" -le "107" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "121" ]; then
ch=$([ "${ch}" -lt "117" ] && echo "113" || echo "117")
bw_str=$([ "${ch}" -le "115" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "129" ]; then
ch=$([ "${ch}" -lt "125" ] && echo "121" || echo "125")
bw_str=$([ "${ch}" -le "123" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "137" ]; then
ch=$([ "${ch}" -lt "133" ] && echo "129" || echo "133")
bw_str=$([ "${ch}" -le "131" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "145" ]; then
ch=$([ "${ch}" -lt "141" ] && echo "137" || echo "141")
bw_str=$([ "${ch}" -le "139" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "153" ]; then
ch=$([ "${ch}" -lt "149" ] && echo "145" || echo "149")
bw_str=$([ "${ch}" -le "147" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "161" ]; then
ch=$([ "${ch}" -lt "157" ] && echo "153" || echo "157")
bw_str=$([ "${ch}" -le "155" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "169" ]; then
ch=$([ "${ch}" -lt "165" ] && echo "161" || echo "165")
bw_str=$([ "${ch}" -le "163" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "177" ]; then
ch=$([ "${ch}" -lt "173" ] && echo "169" || echo "173")
bw_str=$([ "${ch}" -le "171" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "185" ]; then
ch=$([ "${ch}" -lt "181" ] && echo "177" || echo "181")
bw_str=$([ "${ch}" -le "179" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "193" ]; then
ch=$([ "${ch}" -lt "189" ] && echo "185" || echo "189")
bw_str=$([ "${ch}" -le "187" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "201" ]; then
ch=$([ "${ch}" -lt "197" ] && echo "193" || echo "197")
bw_str=$([ "${ch}" -le "195" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "209" ]; then
ch=$([ "${ch}" -lt "205" ] && echo "201" || echo "205")
bw_str=$([ "${ch}" -le "203" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "217" ]; then
ch=$([ "${ch}" -lt "213" ] && echo "209" || echo "213")
bw_str=$([ "${ch}" -le "211" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "225" ]; then
ch=$([ "${ch}" -lt "221" ] && echo "217" || echo "221")
bw_str=$([ "${ch}" -le "219" ] && echo "HT40+" || echo "HT40-")
elif [ ${ch} -lt "233" ]; then
ch=$([ "${ch}" -lt "229" ] && echo "225" || echo "229")
bw_str=$([ "${ch}" -le "227" ] && echo "HT40+" || echo "HT40-")
fi
;;
"0")
local bw_str="HT20"
;;
esac
fi
local control_freq=$(((ch - base_chan) * 5 + base_freq))
do_cmd "iw dev mon${phy_idx} set freq ${control_freq} ${bw_str}"
}
function convert_rxstat {
local res=$(do_cmd "mt76-test ${interface} dump stats")
local mdrdy=$(echo "${res}" | grep "rx_packets" | cut -d "=" -f 2)
local fcs_error=$(echo "${res}" | grep "rx_fcs_error" | cut -d "=" -f 2)
local rcpi=$(echo "${res}" | grep "last_rcpi" | cut -d "=" -f 2 | sed 's/,/ /g')
local ib_rssi=$(echo "${res}" | grep "last_ib_rssi" | cut -d "=" -f 2 | sed 's/,/ /g')
local wb_rssi=$(echo "${res}" | grep "last_wb_rssi" | cut -d "=" -f 2 | sed 's/,/ /g')
local rx_ok=$(expr ${mdrdy} - ${fcs_error})
write_dmesg "rcpi: ${rcpi}"
write_dmesg "fagc rssi ib: ${ib_rssi}"
write_dmesg "fagc rssi wb: ${wb_rssi}"
write_dmesg "all_mac_rx_mdrdy_cnt: ${mdrdy}"
write_dmesg "all_mac_rx_fcs_err_cnt: ${fcs_error}"
write_dmesg "all_mac_rx_ok_cnt : ${rx_ok}"
}
function set_mac_addr {
record_config ${cmd} ${param} ${iwpriv_file}
local addr1=$(get_config "ATEDA" ${iwpriv_file})
local addr2=$(get_config "ATESA" ${iwpriv_file})
local addr3=$(get_config "ATEBSSID" ${iwpriv_file})
if [ -z "${addr1}" ]; then
addr1="00:11:22:33:44:55"
fi
if [ -z "${addr2}" ]; then
addr2="00:11:22:33:44:55"
fi
if [ -z "${addr3}" ]; then
addr3="00:11:22:33:44:55"
fi
do_cmd "mt76-test phy${phy_idx} set mac_addrs=${addr1},${addr2},${addr3}"
}
function convert_ibf {
local cmd=$1
local param=$2
local new_cmd=""
local new_param=$(echo ${param} | sed s/":"/","/g)
case ${cmd} in
"ATETxBfInit")
new_cmd="init"
new_param="1"
do_cmd "mt76-test phy${phy_idx} set state=idle"
;;
"ATETxBfGdInit")
new_cmd="golden_init"
new_param="1"
do_cmd "mt76-test phy${phy_idx} set state=idle"
;;
"ATEIBFPhaseComp")
new_cmd="phase_comp"
new_param="${new_param}"
;;
"ATEEBfProfileConfig")
new_cmd="ebf_prof_update"
;;
"ATEIBfProfileConfig")
new_cmd="ibf_prof_update"
;;
"ATEIBfInstCal")
new_cmd="phase_cal"
;;
"ATEIBfGdCal")
new_cmd="phase_cal"
new_param="${new_param},00"
;;
"TxBfTxApply")
new_cmd="apply_tx"
;;
"ATETxPacketWithBf")
local bf_on=${new_param:0:2}
local aid="01"
local wlan_idx=${new_param:3:2}
local update="00"
local tx_len=${new_param:6}
new_cmd="tx_prep"
new_param="${bf_on},${aid},${wlan_idx},${update}"
if [ "${tx_len}" = "00" ]; then
new_param="${new_param} aid=1 tx_count=10000000 tx_length=1024"
else
new_param="${new_param} aid=1 tx_count=${tx_len} tx_length=1024"
fi
do_cmd "mt76-test phy${phy_idx} set state=idle"
;;
"TxBfProfileData20MAllWrite")
new_cmd="prof_update_all"
;;
"ATEIBFPhaseE2pUpdate")
new_cmd="e2p_update"
;;
"ATEIBFPhaseVerify")
local group=${new_param:0:2}
local group_l_m_h=${new_param:3:2}
local band_idx=${new_param:6:2}
local phase_cal_type=${new_param:9:2}
local LNA_gain_level=${new_param:12:2}
local read_from_e2p=${new_param:15:2}
do_cmd "mt76-test phy${phy_idx} set txbf_act=phase_comp txbf_param=1,${band_idx},${group},${read_from_e2p},0"
new_cmd="phase_cal"
new_param="${group},${group_l_m_h},${band_idx},${phase_cal_type},${LNA_gain_level}"
;;
"TxBfProfileTagRead")
new_cmd="pfmu_tag_read"
;;
"TxBfProfileTagWrite")
new_cmd="pfmu_tag_write"
;;
"TxBfProfileTagInValid")
new_cmd="set_invalid_prof"
;;
"StaRecBfRead")
new_cmd="sta_rec_read"
;;
"TriggerSounding")
new_cmd="trigger_sounding"
;;
"StopSounding")
new_cmd="stop_sounding"
new_param="0"
;;
"TxBfTxCmd")
new_cmd="txcmd"
;;
"ATEConTxETxBfGdProc")
local tx_rate_mode=$(convert_tx_mode ${new_param:0:2})
local tx_rate_idx=${new_param:3:2}
local bw=$(echo ${new_param:6:2} | sed 's/^0//')
local channel=${new_param:9:3}
local channel2=${new_param:13:3}
local band=${new_param:17}
new_cmd="ebf_golden_init"
do_ate_work "ATESTART"
do_cmd "mt76-test phy${phy_idx} set state=idle"
record_config "ATETXBW" ${bw} ${iwpriv_file}
convert_channel "${channel}:${band}"
if [ "${bw}" = "5" ]; then
new_param="1,1"
else
new_param="1,0"
fi
do_cmd "mt76-test phy${phy_idx} set tx_rate_mode=${tx_rate_mode} tx_rate_idx=${tx_rate_idx} tx_rate_sgi=0"
;;
"ATEConTxETxBfInitProc")
local tx_rate_mode=$(convert_tx_mode ${new_param:0:2})
local tx_rate_idx=${new_param:3:2}
local bw=$(echo ${new_param:6:2} | sed 's/^0//')
local tx_rate_nss=${new_param:9:2}
local tx_stream=${new_param:12:2}
local tx_power=${new_param:15:2}
local channel=$(echo ${new_param:18:3} | sed 's/^0//')
local channel2=${new_param:22:3}
local band=${new_param:26:1}
local tx_length=$(echo ${new_param:28:5} | sed 's/^0//')
new_cmd="ebf_init"
do_ate_work "ATESTART"
do_cmd "mt76-test phy${phy_idx} set state=idle"
record_config "ATETXBW" ${bw} ${iwpriv_file}
convert_channel "${channel}:${band}"
new_param="1"
do_cmd "mt76-test phy${phy_idx} set tx_rate_mode=${tx_rate_mode} tx_rate_idx=${tx_rate_idx} tx_rate_nss=${tx_rate_nss} tx_rate_sgi=0 tx_rate_ldpc=1 tx_power=${tx_power},0,0,0 tx_count=10000000 tx_length=${tx_length} tx_ipg=4"
;;
*)
esac
do_cmd "mt76-test phy${phy_idx} set txbf_act=${new_cmd} txbf_param=${new_param}"
if [ "${cmd}" = "ATETxPacketWithBf" ]; then
do_cmd "mt76-test phy${phy_idx} set state=tx_frames"
elif [ "${cmd}" = "ATEConTxETxBfInitProc" ]; then
local wlan_idx="1"
if [ ${is_eagle} == "1" ]; then
local wlan_idx=$((phy_idx+1))
fi
do_cmd "mt76-test phy${phy_idx} set aid=1"
do_cmd "mt76-test phy${phy_idx} set txbf_act=stop_sounding txbf_param=1"
do_cmd "mt76-test phy${phy_idx} set txbf_act=update_ch txbf_param=1"
do_cmd "mt76-test phy${phy_idx} set txbf_act=ebf_prof_update txbf_param=0,0,0"
do_cmd "mt76-test phy${phy_idx} set txbf_act=apply_tx txbf_param=${wlan_idx},1,0,0,0"
if [ ${is_eagle} == "1" ]; then
do_cmd "mt76-test phy${phy_idx} set txbf_act=txcmd txbf_param=1,1,1"
fi
do_cmd "mt76-test phy${phy_idx} set txbf_act=pfmu_tag_read txbf_param=0,1"
do_cmd "mt76-test phy${phy_idx} set txbf_act=sta_rec_read txbf_param=${wlan_idx}"
do_cmd "mt76-test phy${phy_idx} set txbf_act=trigger_sounding txbf_param=0,1,0,${wlan_idx},0,0,0"
do_cmd "mt76-test phy${phy_idx} set txbf_act=trigger_sounding txbf_param=2,1,ff,${wlan_idx},0,0,0"
do_cmd "mt76-test phy${phy_idx} set state=rx_frames"
elif [ "${cmd}" = "ATEConTxETxBfGdProc" ]; then
do_cmd "mt76-test phy${phy_idx} set aid=1"
do_cmd "mt76-test phy${phy_idx} set state=rx_frames"
elif [ "${cmd}" = "ATETxBfInit" ]; then
do_cmd "mt76-test phy${phy_idx} set aid=1"
elif [ "${cmd}" = "ATETxBfGdInit" ]; then
do_cmd "mt76-test phy${phy_idx} set aid=1"
fi
}
function convert_dfs {
local cmd=$1
local param=$2
case ${cmd} in
"DfsRxCtrl")
local offchan_ch="$(echo $param | cut -d ':' -f1)"
local offchan_bw="$(echo $param | cut -d ':' -f2)"
if [ "$offchan_bw" = "0" ]; then
offchan_bw="20"
elif [ "$offchan_bw" = "1" ]; then
offchan_bw="40"
elif [ "$offchan_bw" = "2" ]; then
offchan_bw="80"
elif [ "$offchan_bw" = "3" ]; then
offchan_bw="160"
fi
do_cmd "mt76-test phy${phy_idx} set state=idle"
do_cmd "mt76-test phy${phy_idx} set offchan_ch=${offchan_ch} offchan_bw=${offchan_bw}"
;;
"DfsRxHist")
local ipi_th="$(echo $param | cut -d ':' -f 1)"
local ipi_period="$(echo $param | cut -d ':' -f 2)"
local ipi_antenna="$(echo $param | cut -d ':' -f 3)"
if [ -z $ipi_antenna ]; then
do_cmd "mt76-test phy${phy_idx} set ipi_threshold=${ipi_th} ipi_period=${ipi_period}"
else
do_cmd "mt76-test phy${phy_idx} set ipi_threshold=${ipi_th} ipi_period=${ipi_period} ipi_antenna_idx=${ipi_antenna}"
fi
;;
*)
esac
}
function do_ate_work() {
local ate_cmd=$1
case ${ate_cmd} in
"ATESTART")
local if_str=$(ifconfig | grep mon${phy_idx})
if [ ! -z "${if_str}" -a "${if_str}" != " " ]; then
echo "ATE already starts."
else
do_cmd "iw phy ${interface} interface add mon${phy_idx} type monitor"
if [ $phy_idx -ge $SOC_start_idx ]; then
local end_idx=$SOC_end_idx
local start_idx=$SOC_start_idx
else
local end_idx=$((SOC_start_idx-1))
local start_idx="0"
fi
for phy_index in $( seq $start_idx $end_idx )
do
# "phy#-1" would not be in iw dev, therefore it will grep the line from the phy#${phy_index} to the end
local prev_phy_index=$((phy_index-1))
local if_num=$(iw dev | awk "/phy#${phy_index}/,/phy#${prev_phy_index}/" | grep -c Interface)
local j="1"
# avoid del_if_count reset to 0 when start ate on another band in dbdc case
local del_if_count=$(get_config "DEL_IF${phy_index}_NUM" ${interface_file})
if [ -z "${del_if_count}" ]; then
local del_if_count="0"
fi
for if_count in $( seq 1 $if_num )
do
local del_if=$(iw dev | awk "/phy#${phy_index}/,/phy#${prev_phy_index}/" | grep Interface | sed -n ${j}p | cut -d " " -f 2)
if [ ! -z "${del_if}" ] && [[ "$del_if" != *"mon"* ]]; then
do_cmd "iw dev ${del_if} del"
del_if_count=$((del_if_count+1))
# handle the case of multiple interface in a phy
record_config "DEL_IF${phy_index}-${del_if_count}" ${del_if} ${interface_file}
else
# j add 1 to skip mon interface
j=$((j+1))
fi
done
record_config "DEL_IF${phy_index}_NUM" ${del_if_count} ${interface_file}
done
do_cmd "ifconfig mon${phy_idx} up"
do_cmd "iw reg set VV"
fi
;;
"ATESTOP")
local if_str=$(ifconfig | grep mon${phy_idx})
if [ -z "${if_str}" -a "${if_str}" != " " ]; then
echo "ATE does not start."
else
do_cmd "mt76-test ${interface} set state=off"
do_cmd "iw dev mon${phy_idx} del"
if [ $phy_idx -ge $SOC_start_idx ]; then
local end_idx=$SOC_end_idx
local start_idx=$SOC_start_idx
else
local end_idx=$((SOC_start_idx-1))
local start_idx="0"
fi
# first check its phy and dbdc band phy has monitor interface or not
# if has at lease one mon interface, then skip adding back normal interface
local has_mon="0"
for phy_index in $( seq $start_idx $end_idx )
do
# "phy#-1" would not be in iw dev, therefore it will grep the line from the phy#${phy_index} to the end
local prev_phy_index=$((phy_index-1))
local has_mon_phy=$(iw dev | awk "/phy#${phy_index}/,/phy#${prev_phy_index}/" | grep "Interface mon")
# if this phy interface has mon interface
if [ ! -z "${has_mon_phy}" ]; then
local has_mon="1"
fi
done
for phy_index in $( seq $start_idx $end_idx )
do
# "phy#-1" would not be in iw dev, therefore it will grep the line from the phy#${phy_index} to the end
local prev_phy_index=$((phy_index-1))
local j="1"
local add_if_num=$(get_config "DEL_IF${phy_index}_NUM" ${interface_file})
if [ -z "${add_if_num}" ]; then
local add_if_num="0"
fi
# if this phy interface (including its dbdc phy) has no mon interface and can find deleted interface in file, then add it back
if [ "${has_mon}" == "0" ] && [ $add_if_num -ge "1" ]; then
local if_index=$add_if_num
# add interface backwards
while [ $if_index -gt "0" ]
do
local add_if=$(get_config "DEL_IF${phy_index}-${if_index}" ${interface_file})
do_cmd "iw phy phy${phy_index} interface add ${add_if} type managed"
# remove the deleted interface in interface_file since it is added back
sed -i "/DEL_IF${phy_index}-${if_index}=/d" ${interface_file}
if_index=$((if_index-1))
done
# remove the number of deleted interface in interface_file since it is all added back
sed -i "/DEL_IF${phy_index}_NUM=/d" ${interface_file}
fi
done
do_cmd "mt76-test ${interface} set aid=0"
fi
if [ ${phy_idx} -lt ${SOC_start_idx} ]; then
sed -i '/_PCIE=/d' ${iwpriv_file}
elif [ ${phy_idx} -ge ${SOC_start_idx} ]; then
sed -i '/_SOC=/d' ${iwpriv_file}
fi
;;
"TXCOMMIT")
do_cmd "mt76-test ${interface} set aid=1"
;;
"TXFRAME")
do_cmd "mt76-test ${interface} set state=tx_frames"
;;
"TXSTOP"|"RXSTOP")
do_cmd "mt76-test ${interface} set state=idle"
;;
"TXREVERT")
do_cmd "mt76-test ${interface} set aid=0"
;;
"RXFRAME")
do_cmd "mt76-test ${interface} set state=rx_frames"
;;
"TXCONT")
do_cmd "mt76-test ${interface} set state=tx_cont"
;;
"GROUPREK")
do_cmd "mt76-test ${interface} set state=group_prek"
do_cmd "atenl -i ${interface} -c \"eeprom precal sync group\""
;;
"GROUPREKDump")
do_cmd "mt76-test ${interface} set state=group_prek_dump"
;;
"GROUPREKClean")
do_cmd "mt76-test ${interface} set state=group_prek_clean"
do_cmd "atenl -i ${interface} -c \"eeprom precal group clean\""
;;
"DPD2G")
do_cmd "mt76-test ${interface} set state=dpd_2g"
do_cmd "atenl -i ${interface} -c \"eeprom precal sync dpd 2g\""
;;
"DPD5G")
do_cmd "mt76-test ${interface} set state=dpd_5g"
do_cmd "atenl -i ${interface} -c \"eeprom precal sync dpd 5g\""
;;
"DPD6G")
do_cmd "mt76-test ${interface} set state=dpd_6g"
do_cmd "atenl -i ${interface} -c \"eeprom precal sync dpd 6g\""
;;
"DPDDump")
do_cmd "mt76-test ${interface} set state=dpd_dump"
;;
"DPDClean")
do_cmd "mt76-test ${interface} set state=dpd_clean"
do_cmd "atenl -i ${interface} -c \"eeprom precal dpd clean\""
;;
*)
print_debug "skip ${ate_cmd}"
;;
esac
}
function dump_usage {
echo "Usage:"
echo " mwctl <interface> set csi ctrl=<opt1>,<opt2>,<opt3>,<opt4> (macaddr=<macaddr>)"
echo " mwctl <interface> set csi interval=<interval (us)>"
echo " mwctl <interface> dump csi <packet num> <filename>"
echo " mwctl <interface> set amnt <index>(0x0~0xf) <mac addr>(xx:xx:xx:xx:xx:xx)"
echo " mwctl <interface> dump amnt <index> (0x0~0xf or 0xff)"
echo " mwctl <interface> set ap_rfeatures he_gi=<val>"
echo " mwctl <interface> set ap_rfeatures he_ltf=<val>"
echo " mwctl <interface> set ap_rfeatures trig_type=<enable>,<val> (val: 0-7)"
echo " mwctl <interface> set ap_rfeatures ack_policy=<val> (val: 0-4)"
echo " mwctl <interface> set ap_wireless fixed_mcs=<val>"
echo " mwctl <interface> set ap_wireless ofdma=<val> (0: disable, 1: DL, 2: UL)"
echo " mwctl <interface> set ap_wireless nusers_ofdma=<val>"
echo " mwctl <interface> set ap_wireless ppdu_type=<val> (0: SU, 1: MU, 4: LEGACY)"
echo " mwctl <interface> set ap_wireless add_ba_req_bufsize=<val>"
echo " mwctl <interface> set ap_wireless mimo=<val> (0: DL, 1: UL)"
echo " mwctl <interface> set ap_wireless ampdu=<enable>"
echo " mwctl <interface> set ap_wireless amsdu=<enable>"
echo " mwctl <interface> set ap_wireless cert=<enable>"
echo " mwctl <interface> set mu onoff=<val> (bitmap- UL MU-MIMO(bit3), DL MU-MIMO(bit2), UL OFDMA(bit1), DL OFDMA(bit0))"
echo " mwctl <interface> dump phy_capa"
}
function register_handler {
local phy_idx=$1
local offset=$2
local val=$3
local cmd=$4
local w_cmd="write"
regidx=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/regidx
regval=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/regval
echo ${offset} > ${regidx}
if [[ "${cmd}" == "${w_cmd}" ]]; then
echo ${val} > ${regval}
fi
res=$(cat ${regval} | cut -d 'x' -f 2)
printf "%s mac:[%s]:%s\n" ${interface_ori} ${offset} ${res}
}
# main start here
parse_sku
if [ -z ${interface} ]; then
dump_usage
exit
elif [[ ${interface} == "ra"* ]]; then
convert_interface $interface
elif [[ ${interface} == "phy" ]]; then
# handle mwctl phy phy0 e2p ... case
interface=$2
cmd_type=$3
full_cmd=$4
fi
tmp_work_mode=$(get_config "WORKMODE" ${iwpriv_file})
if [ ! -z ${tmp_work_mode} ]; then
work_mode=${tmp_work_mode}
fi
cmd=$(echo ${full_cmd} | sed s/=/' '/g | cut -d " " -f 1)
param=$(echo ${full_cmd} | sed s/=/' '/g | cut -d " " -f 2)
if [ "${cmd_type}" = "set" ]; then
skip=0
case ${cmd} in
## In wifi 7 chipset, testmode & vendor command both use mwctl
## Therefore this wrapper would translate it to either mt76-test or mt76-vendor based on the attribute of the command
## Translate to mt76-vendor command
"csi"|"amnt"|"ap_rfeatures"|"ap_wireless"|"mu"|"set_muru_manual_config")
if [ ${is_eagle} == "1" ]; then
hostapd_cmd="$(echo $* | sed 's/set/raw/')"
do_cmd "hostapd_cli -i $hostapd_cmd"
else
do_cmd "mt76-vendor $*"
fi
skip=1
;;
"ATE")
do_ate_work ${param}
skip=1
;;
"ATETXCNT"|"ATETXLEN"|"ATETXMCS"|"ATEVHTNSS"|"ATETXLDPC"|"ATETXSTBC"| \
"ATEPKTTXTIME"|"ATEIPG"|"ATEDUTYCYCLE"|"ATETXFREQOFFSET")
cmd_new=$(simple_convert ${cmd})
if [ "${param_new}" = "undefined" ]; then
echo "unknown cmd: ${cmd}"
exit
fi
param_new=${param}
if [ "${cmd}" = "ATETXCNT" ] && [ "${param}" = "0" ]; then
param_new="0xFFFFFFFF"
fi
;;
"ATETXANT"|"ATERXANT")
cmd_new="tx_antenna"
param_new=${param}
;;
"ATETXGI")
if [ ${is_eagle} == "0" ]; then
tx_mode=$(convert_tx_mode $(get_config "ATETXMODE" ${iwpriv_file}))
convert_gi ${tx_mode} ${param}
skip=1
else
cmd_new="tx_rate_sgi"
param_new=${param}
fi
;;
"ATETXMODE")
cmd_new="tx_rate_mode"
param_new=$(convert_tx_mode ${param})
if [ "${param_new}" = "undefined" ]; then
echo "unknown tx mode"
echo "0:cck, 1:ofdm, 2:ht, 4:vht, 8:he_su, 9:he_er, 10:he_tb, 11:he_mu"
exit
else
record_config ${cmd} ${param} ${iwpriv_file}
fi
;;
"ATETXPOW0"|"ATETXPOW1"|"ATETXPOW2"|"ATETXPOW3"|"ATETXPOW")
cmd_new="tx_power"
if [ "${param}" == "127" ]; then
# for iTest verification
exit
fi
param_new="${param},0,0,0"
;;
"ATEMUAID")
cmd_new="aid"
param_new=${param}
;;
"ATETXBW")
record_config ${cmd} ${param} ${iwpriv_file}
skip=1
;;
"ATECHANNEL")
convert_channel ${param}
skip=1
;;
"ATERXSTAT")
convert_rxstat
skip=1
;;
"ATECTRLBANDIDX")
change_band_idx ${param}
skip=1
;;
"ATEDA"|"ATESA"|"ATEBSSID")
set_mac_addr ${cmd} ${param}
skip=1
;;
"DfsRxCtrl"|"DfsRxHist")
convert_dfs ${cmd} ${param}
skip=1
;;
"ATETxBfInit"|"ATETxBfGdInit"|"ATEIBFPhaseComp"|"ATEEBfProfileConfig"|"ATEIBfProfileConfig"| \
"TxBfTxApply"|"ATETxPacketWithBf"|"TxBfProfileData20MAllWrite"|"ATEIBfInstCal"| \
"ATEIBfGdCal"|"ATEIBFPhaseE2pUpdate"|"TriggerSounding"|"StopSounding"|"TxBfTxCmd"| \
"StaRecBfRead"|"TxBfProfileTagInValid"|"TxBfProfileTagWrite"|"TxBfProfileTagRead"| \
"ATEIBFPhaseVerify"|"ATEConTxETxBfGdProc"|"ATEConTxETxBfInitProc")
convert_ibf ${cmd} ${param}
skip=1
;;
"bufferMode")
if [ "${param}" = "2" ]; then
do_cmd "atenl -i ${interface} -c \"eeprom update buffermode\""
fi
skip=1
;;
"ResetCounter"|"ATERXSTATRESET")
skip=1
;;
"WORKMODE")
record_config "WORKMODE" ${param} ${iwpriv_file}
echo "Entering ${param} mode in iwpriv"
skip=1
;;
*)
print_debug "Unknown command to set: ${cmd}"
skip=1
esac
if [ "${skip}" != "1" ]; then
do_cmd "mt76-test ${interface} set ${cmd_new}=${param_new}"
fi
elif [ "${cmd_type}" = "show" ]; then
if [ "${cmd}" = "wtbl" ]; then
wlan_idx=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/wlan_idx
wtbl_info=/sys/kernel/debug/ieee80211/phy${phy_idx}/mt76/wtbl_info
do_cmd "echo ${param} > ${wlan_idx}"
do_cmd "cat ${wtbl_info}"
elif [ "${cmd}" = "ATERXSTAT" ]; then
convert_rxstat
else
do_cmd "mt76-test ${interface} dump"
do_cmd "mt76-test ${interface} dump stats"
fi
elif [ "${cmd_type}" = "e2p" ]; then
# support multiple read write
# eeprom offset write
if [[ ${full_cmd} == *"="* ]]; then
IFS=,
for tuple in $full_cmd
do
cmd=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 1)
param=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 2)
offset=$(printf "0x%s" ${cmd})
val=$(printf "0x%s" ${param})
tmp=$((${val} & 0xff))
tmp=$(printf "0x%x" ${tmp})
do_cmd "atenl -i ${interface} -c \"eeprom set ${offset}=${tmp}\""
offset=$((${offset}))
offset=$(expr ${offset} + "1")
offset=$(printf "0x%x" ${offset})
tmp=$(((${val} >> 8) & 0xff))
tmp=$(printf "0x%x" ${tmp})
do_cmd "atenl -i ${interface} -c \"eeprom set ${offset}=${tmp}\""
done
else
IFS=,
for tuple in $full_cmd
do
cmd=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 1)
param=$(echo ${tuple} | sed s/=/' '/g | cut -d " " -f 2)
offset=$(printf "0x%s" ${cmd})
val=$(printf "0x%s" ${param})
v1=$(do_cmd "atenl -i ${interface} -c \"eeprom read ${param}\"")
v1=$(echo "${v1}" | grep "val =" | cut -d '(' -f 2 | grep -o -E '[0-9]+')
tmp=$(printf "0x%s" ${param})
tmp=$((${tmp}))
param2=$(expr ${tmp} + "1")
param2=$(printf "%x" ${param2})
v2=$(do_cmd "atenl -i ${interface} -c \"eeprom read ${param2}\"")
v2=$(echo "${v2}" | grep "val =" | cut -d '(' -f 2 | grep -o -E '[0-9]+')
param=$(printf "0x%s" ${param})
param=$(printf "%04x" ${param})
param=$(echo $param | tr 'a-z' 'A-Z')
printf "%s e2p:\n" ${interface_ori}
printf "[0x%s]:0x%02x%02x\n" ${param} ${v2} ${v1}
done
fi
elif [ "${cmd_type}" = "mac" ]; then
offset=$(printf "0x%s" ${cmd})
val=$(printf "0x%s" ${param})
# reg write
if [[ ${full_cmd} == *"="* ]]; then
register_handler ${phy_idx} ${offset} ${val} "write"
else
start_addr=$(echo ${full_cmd} | sed s/-/' '/g | cut -d " " -f 1)
end_addr=$(echo ${full_cmd} | sed s/-/' '/g | cut -d " " -f 2)
loop=$((0x${end_addr}-0x${start_addr}))
if [[ ${loop} == "0" ]]; then
register_handler ${phy_idx} ${offset} ${val}
else
i=0
while [ $i -le $loop ]; do
addr=$((0x${start_addr}+$i))
offset=$(printf "0x%x" ${addr})
register_handler ${phy_idx} ${offset} ${val}
i=$(($i + 4))
done
fi
fi
## dump command is only for vendor commands
elif [ "${cmd_type}" = "dump" ]; then
do_cmd "mt76-vendor $*"
elif [ "${cmd_type}" = "switch" ]; then
eeprom_mode_file=sys/kernel/debug/ieee80211/phy0/mt76/eeprom_mode
eeprom_mode=$(cat ${eeprom_mode_file} | grep "mode" | sed -n 2p | cut -d " " -f 4)
eeprom_testmode_offset="1af"
testmode_enable="0"
if [ ${is_eagle} == "0" ]; then
return
fi
if [ "${cmd}" = "testmode" ]; then
testmode_enable="1"
fi
if [ "${eeprom_mode}" = "flash" ]; then
## flash mode should set eeprom testmode offset bit
## efuse/bin file/default bin mode rely on module param only
do_cmd "atenl -i ${interface} -c \"eeprom set 0x${eeprom_testmode_offset}=0x${testmode_enable}\""
## If has no precal, it would not affect
do_cmd "atenl -i ${interface} -c \"eeprom precal sync\""
do_cmd "atenl -i ${interface} -c \"sync eeprom all\""
fi
do_cmd "rmmod mt7996e"
do_cmd "rmmod mt76-connac-lib"
do_cmd "rmmod mt76"
do_cmd "rmmod mac80211"
do_cmd "rmmod cfg80211"
do_cmd "rmmod compat"
do_cmd "insmod compat"
do_cmd "insmod cfg80211"
do_cmd "insmod mac80211"
do_cmd "insmod mt76"
do_cmd "insmod mt76-connac-lib"
do_cmd "insmod mt7996e testmode_enable=${testmode_enable}"
do_cmd "sleep 5"
do_cmd "killall hostapd"
do_cmd "killall netifd"
else
echo "Unknown command"
fi