| Adam Ford | a855481 | 2023-03-23 22:06:16 -0500 | [diff] [blame] | 1 | // SPDX-License-Identifier: GPL-2.0-or-later |
| 2 | /* |
| 3 | * Copyright 2022 Logic PD, Inc dba Beacon EmbeddedWorks |
| 4 | * |
| 5 | */ |
| 6 | |
| 7 | #include <common.h> |
| 8 | #include <hang.h> |
| 9 | #include <init.h> |
| 10 | #include <log.h> |
| 11 | #include <spl.h> |
| 12 | #include <asm/global_data.h> |
| 13 | #include <asm/arch/clock.h> |
| 14 | #include <asm/arch/imx8mp_pins.h> |
| 15 | #include <asm/arch/sys_proto.h> |
| 16 | #include <asm/mach-imx/boot_mode.h> |
| 17 | #include <asm/mach-imx/gpio.h> |
| 18 | #include <asm/mach-imx/iomux-v3.h> |
| 19 | #include <asm/mach-imx/mxc_i2c.h> |
| 20 | #include <asm/arch/ddr.h> |
| 21 | #include <power/pmic.h> |
| 22 | #include <power/pca9450.h> |
| 23 | #include <dm/uclass.h> |
| 24 | #include <dm/device.h> |
| 25 | |
| 26 | DECLARE_GLOBAL_DATA_PTR; |
| 27 | |
| 28 | int spl_board_boot_device(enum boot_device boot_dev_spl) |
| 29 | { |
| 30 | return BOOT_DEVICE_BOOTROM; |
| 31 | } |
| 32 | |
| 33 | void spl_dram_init(void) |
| 34 | { |
| 35 | ddr_init(&dram_timing); |
| 36 | } |
| 37 | |
| 38 | void spl_board_init(void) |
| 39 | { |
| 40 | if (IS_ENABLED(CONFIG_FSL_CAAM)) { |
| 41 | struct udevice *dev; |
| 42 | int ret; |
| 43 | |
| 44 | ret = uclass_get_device_by_driver(UCLASS_MISC, DM_DRIVER_GET(caam_jr), &dev); |
| 45 | if (ret) |
| 46 | printf("Failed to initialize caam_jr: %d\n", ret); |
| 47 | } |
| 48 | /* |
| 49 | * Set GIC clock to 500Mhz for OD VDD_SOC. Kernel driver does |
| 50 | * not allow to change it. Should set the clock after PMIC |
| 51 | * setting done. Default is 400Mhz (system_pll1_800m with div = 2) |
| 52 | * set by ROM for ND VDD_SOC |
| 53 | */ |
| 54 | if (IS_ENABLED(CONFIG_IMX8M_VDD_SOC_850MV)) { |
| 55 | clock_enable(CCGR_GIC, 0); |
| 56 | clock_set_target_val(GIC_CLK_ROOT, CLK_ROOT_ON | CLK_ROOT_SOURCE_SEL(5)); |
| 57 | clock_enable(CCGR_GIC, 1); |
| 58 | } |
| 59 | } |
| 60 | |
| 61 | #if CONFIG_IS_ENABLED(DM_PMIC_PCA9450) |
| 62 | int power_init_board(void) |
| 63 | { |
| 64 | struct udevice *dev; |
| 65 | int ret; |
| 66 | |
| 67 | ret = pmic_get("pmic@25", &dev); |
| 68 | if (ret == -ENODEV) { |
| 69 | puts("No pmic@25\n"); |
| 70 | return 0; |
| 71 | } |
| 72 | if (ret != 0) |
| 73 | return ret; |
| 74 | |
| 75 | /* BUCKxOUT_DVS0/1 control BUCK123 output */ |
| 76 | pmic_reg_write(dev, PCA9450_BUCK123_DVS, 0x29); |
| 77 | |
| 78 | /* |
| 79 | * increase VDD_SOC to typical value 0.95V before first |
| 80 | * DRAM access, set DVS1 to 0.85v for suspend. |
| 81 | * Enable DVS control through PMIC_STBY_REQ and |
| 82 | * set B1_ENMODE=1 (ON by PMIC_ON_REQ=H) |
| 83 | */ |
| 84 | if (CONFIG_IS_ENABLED(IMX8M_VDD_SOC_850MV)) |
| 85 | pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x14); |
| 86 | else |
| 87 | pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x1C); |
| 88 | |
| 89 | pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS1, 0x14); |
| 90 | pmic_reg_write(dev, PCA9450_BUCK1CTRL, 0x59); |
| 91 | |
| 92 | /* Kernel uses OD/OD freq for SOC */ |
| 93 | /* To avoid timing risk from SOC to ARM,increase VDD_ARM to OD voltage 0.95v */ |
| 94 | pmic_reg_write(dev, PCA9450_BUCK2OUT_DVS0, 0x1C); |
| 95 | |
| 96 | return 0; |
| 97 | } |
| 98 | #endif |
| 99 | |
| 100 | #if IS_ENABLED(CONFIG_SPL_LOAD_FIT) |
| 101 | int board_fit_config_name_match(const char *name) |
| 102 | { |
| 103 | /* Just empty function now - can't decide what to choose */ |
| 104 | debug("%s: %s\n", __func__, name); |
| 105 | |
| 106 | return 0; |
| 107 | } |
| 108 | #endif |
| 109 | |
| 110 | void board_init_f(ulong dummy) |
| 111 | { |
| 112 | int ret; |
| 113 | |
| 114 | arch_cpu_init(); |
| 115 | |
| 116 | init_uart_clk(1); |
| 117 | |
| 118 | ret = spl_early_init(); |
| 119 | if (ret) { |
| 120 | debug("spl_init() failed: %d\n", ret); |
| 121 | hang(); |
| 122 | } |
| 123 | |
| 124 | preloader_console_init(); |
| 125 | |
| 126 | enable_tzc380(); |
| 127 | |
| 128 | power_init_board(); |
| 129 | |
| 130 | /* DDR initialization */ |
| 131 | spl_dram_init(); |
| 132 | } |