blob: f8b1cda5bb1a3c854aa60702ed6f5769de1159cd [file] [log] [blame]
Ilya Ledvich38a53c62017-09-24 09:00:25 +03001/*
2 * U-Boot board functions for CompuLab CL-SOM-iMX7 module
3 *
4 * (C) Copyright 2017 CompuLab, Ltd. http://www.compulab.com
5 *
6 * Author: Uri Mashiach <uri.mashiach@compulab.co.il>
7 *
8 * SPDX-License-Identifier: GPL-2.0+
9 */
10
11#include <common.h>
12#include <mmc.h>
13#include <phy.h>
14#include <netdev.h>
15#include <fsl_esdhc.h>
16#include <power/pmic.h>
17#include <power/pfuze3000_pmic.h>
18#include <asm/mach-imx/mxc_i2c.h>
19#include <asm/mach-imx/iomux-v3.h>
20#include <asm/arch-mx7/mx7-pins.h>
21#include <asm/arch-mx7/sys_proto.h>
22#include <asm/arch-mx7/clock.h>
23#include "../common/eeprom.h"
24#include "common.h"
25
26DECLARE_GLOBAL_DATA_PTR;
27
28#ifdef CONFIG_SYS_I2C_MXC
29
30#define I2C_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
31 PAD_CTL_HYS)
32
33#define CL_SOM_IMX7_GPIO_I2C2_SCL IMX_GPIO_NR(1, 6)
34#define CL_SOM_IMX7_GPIO_I2C2_SDA IMX_GPIO_NR(1, 7)
35
36static struct i2c_pads_info cl_som_imx7_i2c_pad_info2 = {
37 .scl = {
38 .i2c_mode = MX7D_PAD_GPIO1_IO06__I2C2_SCL |
39 MUX_PAD_CTRL(I2C_PAD_CTRL),
40 .gpio_mode = MX7D_PAD_GPIO1_IO06__GPIO1_IO6 |
41 MUX_PAD_CTRL(I2C_PAD_CTRL),
42 .gp = CL_SOM_IMX7_GPIO_I2C2_SCL,
43 },
44 .sda = {
45 .i2c_mode = MX7D_PAD_GPIO1_IO07__I2C2_SDA |
46 MUX_PAD_CTRL(I2C_PAD_CTRL),
47 .gpio_mode = MX7D_PAD_GPIO1_IO07__GPIO1_IO7 |
48 MUX_PAD_CTRL(I2C_PAD_CTRL),
49 .gp = CL_SOM_IMX7_GPIO_I2C2_SDA,
50 },
51};
52
53/*
54 * cl_som_imx7_setup_i2c() - I2C pinmux configuration.
55 */
56static void cl_som_imx7_setup_i2c(void)
57{
58 setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &cl_som_imx7_i2c_pad_info2);
59}
60#else /* !CONFIG_SYS_I2C_MXC */
61static void cl_som_imx7_setup_i2c(void) {}
62#endif /* CONFIG_SYS_I2C_MXC */
63
64int dram_init(void)
65{
66 gd->ram_size = imx_ddr_size();
67
68 return 0;
69}
70
71#ifdef CONFIG_FSL_ESDHC
72
73#define CL_SOM_IMX7_GPIO_USDHC3_PWR IMX_GPIO_NR(6, 11)
74
75static struct fsl_esdhc_cfg cl_som_imx7_usdhc_cfg[3] = {
76 {USDHC1_BASE_ADDR, 0, 4},
77 {USDHC3_BASE_ADDR},
78};
79
80int board_mmc_init(bd_t *bis)
81{
82 int i, ret;
83 /*
84 * According to the board_mmc_init() the following map is done:
85 * (U-boot device node) (Physical Port)
86 * mmc0 USDHC1
87 * mmc2 USDHC3 (eMMC)
88 */
89 for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
90 switch (i) {
91 case 0:
92 cl_som_imx7_usdhc1_pads_set();
93 gpio_request(CL_SOM_IMX7_GPIO_USDHC1_CD, "usdhc1_cd");
94 cl_som_imx7_usdhc_cfg[0].sdhc_clk =
95 mxc_get_clock(MXC_ESDHC_CLK);
96 break;
97 case 1:
98 cl_som_imx7_usdhc3_emmc_pads_set();
99 gpio_request(CL_SOM_IMX7_GPIO_USDHC3_PWR, "usdhc3_pwr");
100 gpio_direction_output(CL_SOM_IMX7_GPIO_USDHC3_PWR, 0);
101 udelay(500);
102 gpio_direction_output(CL_SOM_IMX7_GPIO_USDHC3_PWR, 1);
103 cl_som_imx7_usdhc_cfg[1].sdhc_clk =
104 mxc_get_clock(MXC_ESDHC3_CLK);
105 break;
106 default:
107 printf("Warning: you configured more USDHC controllers "
108 "(%d) than supported by the board\n", i + 1);
109 return -EINVAL;
110 }
111
112 ret = fsl_esdhc_initialize(bis, &cl_som_imx7_usdhc_cfg[i]);
113 if (ret)
114 return ret;
115 }
116
117 return 0;
118}
119#endif /* CONFIG_FSL_ESDHC */
120
121#ifdef CONFIG_FEC_MXC
122
123#define CL_SOM_IMX7_ETH1_PHY_NRST IMX_GPIO_NR(1, 4)
124
125/*
126 * cl_som_imx7_rgmii_rework() - Ethernet PHY configuration.
127 */
128static void cl_som_imx7_rgmii_rework(struct phy_device *phydev)
129{
130 unsigned short val;
131
132 /* Ar8031 phy SmartEEE feature cause link status generates glitch,
133 * which cause ethernet link down/up issue, so disable SmartEEE
134 */
135 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x3);
136 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x805d);
137 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4003);
138 val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
139 val &= ~(0x1 << 8);
140 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
141
142 /* To enable AR8031 ouput a 125MHz clk from CLK_25M */
143 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
144 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
145 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
146
147 val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
148 val &= 0xffe3;
149 val |= 0x18;
150 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
151
152 /* introduce tx clock delay */
153 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
154 val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
155 val |= 0x0100;
156 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
157}
158
159int board_phy_config(struct phy_device *phydev)
160{
161 cl_som_imx7_rgmii_rework(phydev);
162
163 if (phydev->drv->config)
164 phydev->drv->config(phydev);
165
166 return 0;
167}
168
169/*
170 * cl_som_imx7_handle_mac_address() - set Ethernet MAC address environment.
171 *
172 * @env_var: MAC address environment variable
173 * @eeprom_bus: I2C bus of the environment EEPROM
174 *
175 * @return: 0 on success, < 0 on failure
176 */
177static int cl_som_imx7_handle_mac_address(char *env_var, uint eeprom_bus)
178{
179 int ret;
180 unsigned char enetaddr[6];
181
182 ret = eth_env_get_enetaddr(env_var, enetaddr);
183 if (ret)
184 return 0;
185
186 ret = cl_eeprom_read_mac_addr(enetaddr, eeprom_bus);
187 if (ret)
188 return ret;
189
190 ret = is_valid_ethaddr(enetaddr);
191 if (!ret)
192 return -1;
193
194 return eth_env_set_enetaddr(env_var, enetaddr);
195}
196
197#define CL_SOM_IMX7_FEC_DEV_ID_PRI 0
198
199int board_eth_init(bd_t *bis)
200{
201 /* set Ethernet MAC address environment */
202 cl_som_imx7_handle_mac_address("ethaddr", CONFIG_SYS_I2C_EEPROM_BUS);
203 /* Ethernet interface pinmux configuration */
204 cl_som_imx7_phy1_rst_pads_set();
205 cl_som_imx7_fec1_pads_set();
206 /* PHY reset */
207 gpio_request(CL_SOM_IMX7_ETH1_PHY_NRST, "eth1_phy_nrst");
208 gpio_direction_output(CL_SOM_IMX7_ETH1_PHY_NRST, 0);
209 mdelay(10);
210 gpio_set_value(CL_SOM_IMX7_ETH1_PHY_NRST, 1);
211 /* MAC initialization */
212 return fecmxc_initialize_multi(bis, CL_SOM_IMX7_FEC_DEV_ID_PRI,
213 CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
214}
215
216/*
217 * cl_som_imx7_setup_fec() - Ethernet MAC 1 clock configuration.
218 * - ENET1 reference clock mode select.
219 * - ENET1_TX_CLK output driver is disabled when configured for ALT1.
220 */
221static void cl_som_imx7_setup_fec(void)
222{
223 struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
224 = (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
225
226 /* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17]*/
227 clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
228 (IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
229 IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
230
231 set_clk_enet(ENET_125MHZ);
232}
233#else /* !CONFIG_FEC_MXC */
234static void cl_som_imx7_setup_fec(void) {}
235#endif /* CONFIG_FEC_MXC */
236
237#ifdef CONFIG_SPI
238
239static void cl_som_imx7_spi_init(void)
240{
241 cl_som_imx7_espi1_pads_set();
242}
243#else /* !CONFIG_SPI */
244static void cl_som_imx7_spi_init(void) {}
245#endif /* CONFIG_SPI */
246
247int board_early_init_f(void)
248{
249 cl_som_imx7_uart1_pads_set();
250 cl_som_imx7_usb_otg1_pads_set();
251
252 return 0;
253}
254
255int board_init(void)
256{
257 /* address of boot parameters */
258 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
259 cl_som_imx7_setup_i2c();
260 cl_som_imx7_setup_fec();
261 cl_som_imx7_spi_init();
262
263 return 0;
264}
265
266#ifdef CONFIG_POWER
267#define I2C_PMIC 0
268int power_init_board(void)
269{
270 struct pmic *p;
271 int ret;
272 unsigned int reg, rev_id;
273
274 ret = power_pfuze3000_init(I2C_PMIC);
275 if (ret)
276 return ret;
277
278 p = pmic_get("PFUZE3000");
279 ret = pmic_probe(p);
280 if (ret)
281 return ret;
282
283 pmic_reg_read(p, PFUZE3000_DEVICEID, &reg);
284 pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
285 printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
286
287 /* disable Low Power Mode during standby mode */
288 pmic_reg_write(p, PFUZE3000_LDOGCTL, 0x1);
289
290 return 0;
291}
292#endif /* CONFIG_POWER */
293
294/*
295 * cl_som_imx7_setup_wdog() - watchdog configuration.
296 * - Output WDOG_B signal to reset external pmic.
297 * - Suspend the watchdog timer during low-power modes.
298 */
299void cl_som_imx7_setup_wdog(void)
300{
301 struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
302
303 cl_som_imx7_wdog_pads_set();
304 set_wdog_reset(wdog);
305 /*
306 * Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
307 * since we use PMIC_PWRON to reset the board.
308 */
309 clrsetbits_le16(&wdog->wcr, 0, 0x10);
310}
311
312int board_late_init(void)
313{
314 env_set("board_name", "CL-SOM-iMX7");
315 cl_som_imx7_setup_wdog();
316 return 0;
317}
318
319int checkboard(void)
320{
321 char *mode;
322
323 if (IS_ENABLED(CONFIG_ARMV7_BOOT_SEC_DEFAULT))
324 mode = "secure";
325 else
326 mode = "non-secure";
327
328 printf("Board: CL-SOM-iMX7 in %s mode\n", mode);
329
330 return 0;
331}