include/configs/kilauea.h

/*
 * Copyright (c) 2008 Nuovation System Designs, LLC
 *   Grant Erickson <gerickson@nuovations.com>
 *
 * (C) Copyright 2007
 * Stefan Roese, DENX Software Engineering, sr@denx.de.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/************************************************************************
 * kilauea.h - configuration for AMCC Kilauea (405EX)
 ***********************************************************************/

#ifndef __CONFIG_H
#define __CONFIG_H

/*-----------------------------------------------------------------------
 * High Level Configuration Options
 *----------------------------------------------------------------------*/
#define CONFIG_KILAUEA		1		/* Board is Kilauea	*/
#define CONFIG_405EX		1		/* Specifc 405EX support*/
#define CONFIG_SYS_CLK_FREQ	33333333	/* ext frequency to pll	*/

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE	0xFFFA0000
#endif

/*
 * CHIP_21 errata - you must set this to match your exact CPU, else your
 * board will not boot.  DO NOT enable this unless you have JTAG available
 * for recovery, in the event you get it wrong.
 *
 * Kilauea uses the 405EX, while Haleakala uses the 405EXr.  Either board
 * may be equipped for security or not.  You must look at the CPU part
 * number to be sure what you have.
 */
/* #define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY */
/* #define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY */
/* #define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY */
/* #define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY */

/*
 * Include common defines/options for all AMCC eval boards
 */
#define CONFIG_HOSTNAME		kilauea
#include "amcc-common.h"

#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
#define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
#define CONFIG_BOARD_TYPES
#define CONFIG_BOARD_EMAC_COUNT

/*-----------------------------------------------------------------------
 * Base addresses -- Note these are effective addresses where the
 * actual resources get mapped (not physical addresses)
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH_BASE		0xFC000000
#define CONFIG_SYS_NAND_ADDR		0xF8000000
#define CONFIG_SYS_FPGA_BASE		0xF0000000

/*-----------------------------------------------------------------------
 * Initial RAM & Stack Pointer Configuration Options
 *
 *   There are traditionally three options for the primordial
 *   (i.e. initial) stack usage on the 405-series:
 *
 *      1) On-chip Memory (OCM) (i.e. SRAM)
 *      2) Data cache
 *      3) SDRAM
 *
 *   For the 405EX(r), there is no OCM, so we are left with (2) or (3)
 *   the latter of which is less than desireable since it requires
 *   setting up the SDRAM and ECC in assembly code.
 *
 *   To use (2), define 'CONFIG_SYS_INIT_DCACHE_CS' to be an unused chip
 *   select on the External Bus Controller (EBC) and then select a
 *   value for 'CONFIG_SYS_INIT_RAM_ADDR' outside of the range of valid,
 *   physical SDRAM. Otherwise, undefine 'CONFIG_SYS_INIT_DCACHE_CS' and
 *   select a value for 'CONFIG_SYS_INIT_RAM_ADDR' within the range of valid,
 *   physical SDRAM to use (3).
 *-----------------------------------------------------------------------*/

#define CONFIG_SYS_INIT_DCACHE_CS	4

#if defined(CONFIG_SYS_INIT_DCACHE_CS)
#define CONFIG_SYS_INIT_RAM_ADDR	(CONFIG_SYS_SDRAM_BASE + ( 1 << 30))	/*  1 GiB */
#else
#define CONFIG_SYS_INIT_RAM_ADDR	(CONFIG_SYS_SDRAM_BASE + (32 << 20))	/* 32 MiB */
#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */

#define CONFIG_SYS_INIT_RAM_SIZE        (4 << 10)			/*  4 KiB */
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

/*
 * If the data cache is being used for the primordial stack and global
 * data area, the POST word must be placed somewhere else. The General
 * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves
 * its compare and mask register contents across reset, so it is used
 * for the POST word.
 */

#if defined(CONFIG_SYS_INIT_DCACHE_CS)
# define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
# define CONFIG_SYS_POST_WORD_ADDR	(CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
#else
# define CONFIG_SYS_INIT_EXTRA_SIZE	16
# define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_EXTRA_SIZE)
# define CONFIG_SYS_OCM_DATA_ADDR	CONFIG_SYS_INIT_RAM_ADDR
#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */

/*-----------------------------------------------------------------------
 * Serial Port
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_EXT_SERIAL_CLOCK	11059200	/* ext. 11.059MHz clk	*/
#define CONFIG_CONS_INDEX	1	/* Use UART0			*/

/*-----------------------------------------------------------------------
 * Environment
 *----------------------------------------------------------------------*/
#define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/

/*-----------------------------------------------------------------------
 * FLASH related
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH_CFI			/* The flash is CFI compatible	*/
#define CONFIG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/

#define CONFIG_SYS_FLASH_BANKS_LIST    {CONFIG_SYS_FLASH_BASE}
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */

#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE	0x20000	/* size of one complete sector	*/
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
#endif /* CONFIG_ENV_IS_IN_FLASH */

/*-----------------------------------------------------------------------
 * NAND FLASH
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_BASE		(CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
#define CONFIG_SYS_NAND_SELECT_DEVICE  1	/* nand driver supports mutipl. chips	*/

/*-----------------------------------------------------------------------
 * DDR SDRAM
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_MBYTES_SDRAM        (256)		/* 256MB			*/

/*
 * CONFIG_PPC4xx_DDR_AUTOCALIBRATION
 *
 * Note: DDR Autocalibration Method_A scans the full range of possible PPC4xx
 *       SDRAM Controller DDR autocalibration values and takes a lot longer
 *       to run than Method_B.
 * (See the Method_A and Method_B algorithm discription in the file:
 *	arch/powerpc/cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c)
 * Define CONFIG_PPC4xx_DDR_METHOD_A to use DDR autocalibration Method_A
 *
 * DDR Autocalibration Method_B is the default.
 */
#define	CONFIG_PPC4xx_DDR_AUTOCALIBRATION	/* IBM DDR autocalibration */
#define	DEBUG_PPC4xx_DDR_AUTOCALIBRATION	/* dynamic DDR autocal debug */
#undef	CONFIG_PPC4xx_DDR_METHOD_A

#define	CONFIG_SYS_SDRAM0_MB0CF_BASE	((  0 << 20) + CONFIG_SYS_SDRAM_BASE)

/* DDR1/2 SDRAM Device Control Register Data Values */
#define CONFIG_SYS_SDRAM0_MB0CF	((CONFIG_SYS_SDRAM0_MB0CF_BASE >> 3)	| \
				 SDRAM_RXBAS_SDSZ_256MB		| \
				 SDRAM_RXBAS_SDAM_MODE7		| \
				 SDRAM_RXBAS_SDBE_ENABLE)
#define CONFIG_SYS_SDRAM0_MB1CF	SDRAM_RXBAS_SDBE_DISABLE
#define CONFIG_SYS_SDRAM0_MB2CF	SDRAM_RXBAS_SDBE_DISABLE
#define CONFIG_SYS_SDRAM0_MB3CF	SDRAM_RXBAS_SDBE_DISABLE
#define CONFIG_SYS_SDRAM0_MCOPT1	(SDRAM_MCOPT1_PMU_OPEN		| \
				 SDRAM_MCOPT1_8_BANKS		| \
				 SDRAM_MCOPT1_DDR2_TYPE		| \
				 SDRAM_MCOPT1_QDEP		| \
				 SDRAM_MCOPT1_DCOO_DISABLED)
#define CONFIG_SYS_SDRAM0_MCOPT2	0x00000000
#define CONFIG_SYS_SDRAM0_MODT0	(SDRAM_MODT_EB0W_ENABLE | \
				 SDRAM_MODT_EB0R_ENABLE)
#define CONFIG_SYS_SDRAM0_MODT1	0x00000000
#define CONFIG_SYS_SDRAM0_CODT		(SDRAM_CODT_RK0R_ON		| \
				 SDRAM_CODT_CKLZ_36OHM		| \
				 SDRAM_CODT_DQS_1_8_V_DDR2	| \
				 SDRAM_CODT_IO_NMODE)
#define CONFIG_SYS_SDRAM0_RTR		SDRAM_RTR_RINT_ENCODE(1560)
#define CONFIG_SYS_SDRAM0_INITPLR0	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(80)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_NOP))
#define CONFIG_SYS_SDRAM0_INITPLR1	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(3)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE)		| \
		SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR)			| \
		SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL))
#define CONFIG_SYS_SDRAM0_INITPLR2	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(2)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR)		| \
		SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR2)			| \
		SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR2_TEMP_COMMERCIAL))
#define CONFIG_SYS_SDRAM0_INITPLR3	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(2)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR)		| \
		SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR3)			| \
		SDRAM_INITPLR_IMA_ENCODE(0))
#define CONFIG_SYS_SDRAM0_INITPLR4	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(2)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR)		| \
		SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR)			| \
		SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_DQS_DISABLE | \
					 JEDEC_MA_EMR_RTT_75OHM))
#define CONFIG_SYS_SDRAM0_INITPLR5	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(2)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR)		| \
		SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR)			| \
		SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \
					 JEDEC_MA_MR_CL_DDR2_4_0_CLK | \
					 JEDEC_MA_MR_BLEN_4 | \
					 JEDEC_MA_MR_DLL_RESET))
#define CONFIG_SYS_SDRAM0_INITPLR6	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(3)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE)		| \
		SDRAM_INITPLR_IBA_ENCODE(0x0)				| \
		SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL))
#define CONFIG_SYS_SDRAM0_INITPLR7	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(26)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
#define CONFIG_SYS_SDRAM0_INITPLR8	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(26)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
#define CONFIG_SYS_SDRAM0_INITPLR9	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(26)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
#define CONFIG_SYS_SDRAM0_INITPLR10	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(26)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
#define CONFIG_SYS_SDRAM0_INITPLR11	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(2)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR)		| \
		SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR)			| \
		SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \
					 JEDEC_MA_MR_CL_DDR2_4_0_CLK | \
					 JEDEC_MA_MR_BLEN_4))
#define CONFIG_SYS_SDRAM0_INITPLR12	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(2)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR)		| \
		SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR)			| \
		SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_ENTER	| \
					 JEDEC_MA_EMR_RDQS_DISABLE | \
					 JEDEC_MA_EMR_DQS_DISABLE | \
					 JEDEC_MA_EMR_RTT_DISABLED | \
					 JEDEC_MA_EMR_ODS_NORMAL))
#define CONFIG_SYS_SDRAM0_INITPLR13	(SDRAM_INITPLR_ENABLE			| \
		SDRAM_INITPLR_IMWT_ENCODE(2)				| \
		SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR)		| \
		SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR)			| \
		SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_EXIT | \
					 JEDEC_MA_EMR_RDQS_DISABLE | \
					 JEDEC_MA_EMR_DQS_DISABLE | \
					 JEDEC_MA_EMR_RTT_DISABLED | \
					 JEDEC_MA_EMR_ODS_NORMAL))
#define CONFIG_SYS_SDRAM0_INITPLR14	(SDRAM_INITPLR_DISABLE)
#define CONFIG_SYS_SDRAM0_INITPLR15	(SDRAM_INITPLR_DISABLE)
#define CONFIG_SYS_SDRAM0_RQDC		(SDRAM_RQDC_RQDE_ENABLE | \
				 SDRAM_RQDC_RQFD_ENCODE(56))
#define CONFIG_SYS_SDRAM0_RFDC		SDRAM_RFDC_RFFD_ENCODE(521)
#define CONFIG_SYS_SDRAM0_RDCC		(SDRAM_RDCC_RDSS_T2)
#define CONFIG_SYS_SDRAM0_DLCR		(SDRAM_DLCR_DCLM_AUTO		| \
				 SDRAM_DLCR_DLCS_CONT_DONE	| \
				 SDRAM_DLCR_DLCV_ENCODE(165))
#define CONFIG_SYS_SDRAM0_CLKTR	(SDRAM_CLKTR_CLKP_180_DEG_ADV)
#define CONFIG_SYS_SDRAM0_WRDTR	0x00000000
#define CONFIG_SYS_SDRAM0_SDTR1	(SDRAM_SDTR1_LDOF_2_CLK	| \
				 SDRAM_SDTR1_RTW_2_CLK	| \
				 SDRAM_SDTR1_RTRO_1_CLK)
#define CONFIG_SYS_SDRAM0_SDTR2	(SDRAM_SDTR2_RCD_3_CLK		| \
				 SDRAM_SDTR2_WTR_2_CLK		| \
				 SDRAM_SDTR2_XSNR_32_CLK	| \
				 SDRAM_SDTR2_WPC_4_CLK		| \
				 SDRAM_SDTR2_RPC_2_CLK		| \
				 SDRAM_SDTR2_RP_3_CLK		| \
				 SDRAM_SDTR2_RRD_2_CLK)
#define CONFIG_SYS_SDRAM0_SDTR3	(SDRAM_SDTR3_RAS_ENCODE(8)	| \
				 SDRAM_SDTR3_RC_ENCODE(11)	| \
				 SDRAM_SDTR3_XCS		| \
				 SDRAM_SDTR3_RFC_ENCODE(26))
#define CONFIG_SYS_SDRAM0_MMODE	(SDRAM_MMODE_WR_DDR2_3_CYC | \
				 SDRAM_MMODE_DCL_DDR2_4_0_CLK | \
				 SDRAM_MMODE_BLEN_4)
#define CONFIG_SYS_SDRAM0_MEMODE	(SDRAM_MEMODE_DQS_DISABLE | \
				 SDRAM_MEMODE_RTT_75OHM)

/*-----------------------------------------------------------------------
 * I2C
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000

#define CONFIG_SYS_I2C_EEPROM_ADDR	0x52	/* I2C boot EEPROM (24C02BN)	*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10

/* I2C bootstrap EEPROM */
#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR	0x52
#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET	0
#define CONFIG_4xx_CONFIG_BLOCKSIZE		16

/* Standard DTT sensor configuration */
#define CONFIG_DTT_DS1775	1
#define CONFIG_DTT_SENSORS	{ 0 }
#define CONFIG_SYS_I2C_DTT_ADDR	0x48

/* RTC configuration */
#define CONFIG_RTC_DS1338	1
#define CONFIG_SYS_I2C_RTC_ADDR	0x68

/*-----------------------------------------------------------------------
 * Ethernet
 *----------------------------------------------------------------------*/
#define CONFIG_M88E1111_PHY	1
#define CONFIG_IBM_EMAC4_V4	1
#define CONFIG_EMAC_PHY_MODE	EMAC_PHY_MODE_RGMII_RGMII
#define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/

#define CONFIG_PHY_RESET	1	/* reset phy upon startup	*/
#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */

#define CONFIG_HAS_ETH0		1

#define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"   */
#define CONFIG_PHY1_ADDR	2

/* Debug messages for the DDR autocalibration */
#define CONFIG_AUTOCALIB		"silent\0"  /* default is non-verbose */

/*
 * Default environment variables
 */
#define	CONFIG_EXTRA_ENV_SETTINGS					\
	CONFIG_AMCC_DEF_ENV						\
	CONFIG_AMCC_DEF_ENV_POWERPC					\
	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
	"logversion=2\0"						\
	"kernel_addr=fc000000\0"					\
	"fdt_addr=fc1e0000\0"						\
	"ramdisk_addr=fc200000\0"					\
	"pciconfighost=1\0"						\
	"pcie_mode=RP:RP\0"						\
	""

/*
 * Commands additional to the ones defined in amcc-common.h
 */
#define CONFIG_CMD_CHIP_CONFIG
#define CONFIG_CMD_DATE
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SNTP

#define CONFIG_SYS_POST_MEMORY_ON	CONFIG_SYS_POST_MEMORY

/* POST support */
#define CONFIG_POST		(CONFIG_SYS_POST_CACHE		| \
				 CONFIG_SYS_POST_CPU		| \
				 CONFIG_SYS_POST_ETHER		| \
				 CONFIG_SYS_POST_I2C		| \
				 CONFIG_SYS_POST_MEMORY_ON	| \
				 CONFIG_SYS_POST_UART)

/* Define here the base-addresses of the UARTs to test in POST */
#define CONFIG_SYS_POST_UART_TABLE	{ CONFIG_SYS_NS16550_COM1, \
			CONFIG_SYS_NS16550_COM2 }

#define CONFIG_LOGBUFFER
#define CONFIG_SYS_POST_CACHE_ADDR	0x00800000 /* free virtual address	*/

#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */

/*-----------------------------------------------------------------------
 * PCI stuff
 *----------------------------------------------------------------------*/
#define CONFIG_PCI			/* include pci support	        */
#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
#define CONFIG_PCI_PNP		1	/* do pci plug-and-play		*/
#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
#define CONFIG_PCI_CONFIG_HOST_BRIDGE

/*-----------------------------------------------------------------------
 * PCIe stuff
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_PCIE_MEMBASE	0x90000000	/* mapped PCIe memory	*/
#define CONFIG_SYS_PCIE_MEMSIZE	0x08000000      /* 128 Meg, smallest incr per port */

#define	CONFIG_SYS_PCIE0_CFGBASE	0xa0000000      /* remote access */
#define	CONFIG_SYS_PCIE0_XCFGBASE	0xb0000000      /* local access */
#define	CONFIG_SYS_PCIE0_CFGMASK	0xe0000001      /* 512 Meg */

#define	CONFIG_SYS_PCIE1_CFGBASE	0xc0000000      /* remote access */
#define	CONFIG_SYS_PCIE1_XCFGBASE	0xd0000000      /* local access */
#define	CONFIG_SYS_PCIE1_CFGMASK	0xe0000001      /* 512 Meg */

#define	CONFIG_SYS_PCIE0_UTLBASE	0xef502000
#define	CONFIG_SYS_PCIE1_UTLBASE	0xef503000

/* base address of inbound PCIe window */
#define CONFIG_SYS_PCIE_INBOUND_BASE	0x0000000000000000ULL

/*-----------------------------------------------------------------------
 * External Bus Controller (EBC) Setup
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_NAND_CS		1		/* NAND chip connected to CSx	*/

/* Memory Bank 0 (NOR-FLASH) initialization					*/
#define CONFIG_SYS_EBC_PB0AP		0x05806500
#define CONFIG_SYS_EBC_PB0CR           0xFC0DA000  /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/

/* Memory Bank 1 (NAND-FLASH) initialization					*/
#define CONFIG_SYS_EBC_PB1AP		0x018003c0
#define CONFIG_SYS_EBC_PB1CR		(CONFIG_SYS_NAND_ADDR | 0x1e000)

/* Memory Bank 2 (FPGA) initialization					*/
#define CONFIG_SYS_EBC_PB2AP		(EBC_BXAP_BME_ENABLED |		\
					 EBC_BXAP_FWT_ENCODE(6) |	\
					 EBC_BXAP_BWT_ENCODE(1) |	\
					 EBC_BXAP_BCE_DISABLE |		\
					 EBC_BXAP_BCT_2TRANS |		\
					 EBC_BXAP_CSN_ENCODE(0) |	\
					 EBC_BXAP_OEN_ENCODE(0) |	\
					 EBC_BXAP_WBN_ENCODE(3) |	\
					 EBC_BXAP_WBF_ENCODE(1) |	\
					 EBC_BXAP_TH_ENCODE(4) |	\
					 EBC_BXAP_RE_DISABLED |		\
					 EBC_BXAP_SOR_DELAYED |		\
					 EBC_BXAP_BEM_WRITEONLY |	\
					 EBC_BXAP_PEN_DISABLED)
#define CONFIG_SYS_EBC_PB2CR	(CONFIG_SYS_FPGA_BASE | 0x18000)

#define CONFIG_SYS_EBC_CFG		0x7FC00000 /*  EBC0_CFG */

/*-----------------------------------------------------------------------
 * GPIO Setup
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_4xx_GPIO_TABLE { /*	  Out		  GPIO	Alternate1	Alternate2	Alternate3 */ \
{											\
/* GPIO Core 0 */									\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO0	EBC_DATA_PAR(0)			*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO1	EBC_DATA_PAR(1)			*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO2	EBC_DATA_PAR(2)			*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO3	EBC_DATA_PAR(3)			*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO4	EBC_DATA(20)	USB2_DATA(4)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO5	EBC_DATA(21)	USB2_DATA(5)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO6	EBC_DATA(22)	USB2_DATA(6)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO7	EBC_DATA(23)	USB2_DATA(7)	*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8	CS(1)/NFCE(1)	IRQ(7)		*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9	CS(2)/NFCE(2)	IRQ(8)		*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3)	IRQ(9)		*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 IRQ(6)				*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16)	USB2_DATA(0)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17)	USB2_DATA(1)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18)	USB2_DATA(2)	*/	\
{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19)	USB2_DATA(3)	*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD	UART1_CTS	*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR	UART1_RTS	*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS			*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS			*/	\
{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO20 UART0_DTR	UART1_TX	*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO21 UART0_RI	UART1_RX	*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ	DMA_ACK2	*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK	DMA_REQ2	*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ	DMA_EOT2	IRQ(4) */ \
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK	DMA_ACK3	IRQ(3) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5)	DMA_EOT0	TS(3) */ \
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ	DMA_EOT3	IRQ(5) */ \
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO28				*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO29 DMA_EOT1	IRQ(2)		*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO30 DMA_REQ1	IRQ(1)		*/	\
{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO31 DMA_ACK1	IRQ(0)		*/	\
}												\
}

/*-----------------------------------------------------------------------
 * Some Kilauea stuff..., mainly fpga registers
 */
#define CONFIG_SYS_FPGA_REG_BASE		CONFIG_SYS_FPGA_BASE
#define CONFIG_SYS_FPGA_FIFO_BASE		(CONFIG_SYS_FPGA_BASE | (1 << 10))

/* interrupt */
#define CONFIG_SYS_FPGA_SLIC0_R_DPRAM_INT	0x80000000
#define CONFIG_SYS_FPGA_SLIC0_W_DPRAM_INT	0x40000000
#define CONFIG_SYS_FPGA_SLIC1_R_DPRAM_INT	0x20000000
#define CONFIG_SYS_FPGA_SLIC1_W_DPRAM_INT	0x10000000
#define CONFIG_SYS_FPGA_PHY0_INT		0x08000000
#define CONFIG_SYS_FPGA_PHY1_INT		0x04000000
#define CONFIG_SYS_FPGA_SLIC0_INT		0x02000000
#define CONFIG_SYS_FPGA_SLIC1_INT		0x01000000

/* DPRAM setting */
/* 00: 32B; 01: 64B; 10: 128B; 11: 256B  */
#define CONFIG_SYS_FPGA_DPRAM_R_INT_LINE	0x00400000	/* 64 B */
#define CONFIG_SYS_FPGA_DPRAM_W_INT_LINE	0x00100000	/* 64 B */
#define CONFIG_SYS_FPGA_DPRAM_RW_TYPE		0x00080000
#define CONFIG_SYS_FPGA_DPRAM_RST		0x00040000
#define CONFIG_SYS_FPGA_UART0_FO		0x00020000
#define CONFIG_SYS_FPGA_UART1_FO		0x00010000

/* loopback */
#define CONFIG_SYS_FPGA_CHIPSIDE_LOOPBACK	0x00004000
#define CONFIG_SYS_FPGA_LINESIDE_LOOPBACK	0x00008000
#define CONFIG_SYS_FPGA_SLIC0_ENABLE		0x00002000
#define CONFIG_SYS_FPGA_SLIC1_ENABLE		0x00001000
#define CONFIG_SYS_FPGA_SLIC0_CS		0x00000800
#define CONFIG_SYS_FPGA_SLIC1_CS		0x00000400
#define CONFIG_SYS_FPGA_USER_LED0		0x00000200
#define CONFIG_SYS_FPGA_USER_LED1		0x00000100

#define CONFIG_SYS_FPGA_MAGIC_MASK		0xffff0000
#define CONFIG_SYS_FPGA_MAGIC			0xabcd0000
#define CONFIG_SYS_FPGA_VER_MASK		0x0000ff00

#endif	/* __CONFIG_H */