include/configs/PK1C20.h

/*
 * (C) Copyright 2004, Psyent Corporation <www.psyent.com>
 * Scott McNutt <smcnutt@psyent.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*------------------------------------------------------------------------
 * BOARD/CPU
 *----------------------------------------------------------------------*/
#define CONFIG_PK1C20		1		/* PK1C20 board		*/
#define CONFIG_SYS_CLK_FREQ	50000000	/* 50 MHz core clk	*/

#define CONFIG_SYS_RESET_ADDR		0x00000000	/* Hard-reset address	*/
#define CONFIG_SYS_EXCEPTION_ADDR	0x01000020	/* Exception entry point*/
#define CONFIG_SYS_NIOS_SYSID_BASE	0x021208b8	/* System id address	*/
#define CONFIG_BOARD_EARLY_INIT_F 1	/* enable early board-spec. init*/

/*------------------------------------------------------------------------
 * CACHE -- the following will support II/s and II/f. The II/s does not
 * have dcache, so the cache instructions will behave as NOPs.
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_ICACHE_SIZE		4096		/* 4 KByte total	*/
#define CONFIG_SYS_ICACHELINE_SIZE	32		/* 32 bytes/line	*/
#define CONFIG_SYS_DCACHE_SIZE		2048		/* 2 KByte (II/f)	*/
#define CONFIG_SYS_DCACHELINE_SIZE	4		/* 4 bytes/line (II/f)	*/

/*------------------------------------------------------------------------
 * MEMORY BASE ADDRESSES
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH_BASE		0x00000000	/* FLASH base addr	*/
#define CONFIG_SYS_FLASH_SIZE		0x00800000	/* 8 MByte		*/
#define CONFIG_SYS_SDRAM_BASE		0x01000000	/* SDRAM base addr	*/
#define CONFIG_SYS_SDRAM_SIZE		0x01000000	/* 16 MByte		*/
#define CONFIG_SYS_SRAM_BASE		0x02000000	/* SRAM base addr	*/
#define CONFIG_SYS_SRAM_SIZE		0x00100000	/* 1 MB (only 1M mapped)*/

/*------------------------------------------------------------------------
 * MEMORY ORGANIZATION
 *	-Monitor at top.
 *	-The heap is placed below the monitor.
 *	-Global data is placed below the heap.
 *	-The stack is placed below global data (&grows down).
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 128k		*/
#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128*1024)

#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_MALLOC_BASE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP		CONFIG_SYS_GBL_DATA_OFFSET

/*------------------------------------------------------------------------
 * FLASH (AM29LV065D)
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_MAX_FLASH_SECT	128		/* Max # sects per bank */
#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* Max # of flash banks */
#define CONFIG_SYS_FLASH_ERASE_TOUT	8000		/* Erase timeout (msec) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	100		/* Write timeout (msec) */
#define CONFIG_SYS_FLASH_WORD_SIZE	unsigned char	/* flash word size	*/

/*------------------------------------------------------------------------
 * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
 * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
 * reset address, no? This will keep the environment in user region
 * of flash. NOTE: the monitor length must be multiple of sector size
 * (which is common practice).
 *----------------------------------------------------------------------*/
#define CONFIG_ENV_IS_IN_FLASH	1		/* Environment in flash */
#define CONFIG_ENV_SIZE		(64 * 1024)	/* 64 KByte (1 sector)	*/
#define CONFIG_ENV_OVERWRITE			/* Serial change Ok	*/
#define CONFIG_ENV_ADDR	(CONFIG_SYS_RESET_ADDR + CONFIG_SYS_MONITOR_LEN)

/*------------------------------------------------------------------------
 * CONSOLE
 *----------------------------------------------------------------------*/
#define CONFIG_ALTERA_UART		1	/* Use altera uart */
#if defined(CONFIG_ALTERA_JTAG_UART)
#define CONFIG_SYS_NIOS_CONSOLE	0x021208b0	/* JTAG UART base addr	*/
#else
#define CONFIG_SYS_NIOS_CONSOLE	0x02120840	/* UART base addr	*/
#endif

#define CONFIG_SYS_NIOS_FIXEDBAUD	1		/* Baudrate is fixed	*/
#define CONFIG_BAUDRATE		115200		/* Initial baudrate	*/
#define CONFIG_SYS_BAUDRATE_TABLE	{115200}	/* It's fixed ;-)	*/

#define CONFIG_SYS_CONSOLE_INFO_QUIET	1		/* Suppress console info*/

/*------------------------------------------------------------------------
 * EPCS Device -- wne CONFIG_SYS_NIOS_EPCSBASE is defined code/commands for
 * epcs device access is enabled. The base address is the epcs
 * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK.
 * The register base is currently at offset 0x600 from the memory base.
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_NIOS_EPCSBASE	0x02100200	/* EPCS register base	*/

/*------------------------------------------------------------------------
 * DEBUG
 *----------------------------------------------------------------------*/
#undef CONFIG_ROM_STUBS				/* Stubs not in ROM	*/

/*------------------------------------------------------------------------
 * TIMEBASE --
 *
 * The high res timer defaults to 1 msec. Since it includes the period
 * registers, the interrupt frequency can be reduced using TMRCNT.
 * If the default period is acceptable, TMRCNT can be left undefined.
 * TMRMS represents the desired mecs per tick (msecs per interrupt).
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_HZ			1000	/* Always 1000 */
#define CONFIG_SYS_LOW_RES_TIMER
#define CONFIG_SYS_NIOS_TMRBASE	0x02120820	/* Tick timer base addr */
#define CONFIG_SYS_NIOS_TMRIRQ		3	/* Timer IRQ num */
#define CONFIG_SYS_NIOS_TMRMS		10	/* Desired period */
#define CONFIG_SYS_NIOS_TMRCNT \
		(CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))

/*------------------------------------------------------------------------
 * STATUS LED -- Provides a simple blinking led. For Nios2 each board
 * must implement its own led routines -- leds are, after all,
 * board-specific, no?
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_LEDPIO_ADDR		0x02120870	/* LED PIO base addr	*/
#define CONFIG_STATUS_LED			/* Enable status driver */
#define CONFIG_BOARD_SPECIFIC_LED

#define STATUS_LED_BIT		1		/* Bit-0 on PIO		*/
#define STATUS_LED_STATE	1		/* Blinking		*/
#define STATUS_LED_PERIOD	(500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec	*/

/*------------------------------------------------------------------------
 * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
 * and really doesn't need any additional clutter. So I choose the lazy
 * way out to avoid changes there -- define the base address to ensure
 * cache bypass so there's no need to monkey with inx/outx macros.
 *----------------------------------------------------------------------*/
#define CONFIG_SMC91111_BASE	0x82110300	/* Base addr (bypass)	*/
#define CONFIG_SMC91111			/* Using SMC91c111	*/
#undef	CONFIG_SMC91111_EXT_PHY			/* Internal PHY		*/
#define CONFIG_SMC_USE_32_BIT			/* 32-bit interface	*/

#define CONFIG_ETHADDR		08:00:3e:26:0a:5b
#define CONFIG_NETMASK		255.255.255.0
#define CONFIG_IPADDR		192.168.2.21
#define CONFIG_SERVERIP		192.168.2.16


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */

#define CONFIG_CMD_BDI
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ECHO
#define CONFIG_CMD_SAVEENV
#define CONFIG_CMD_FLASH
#define CONFIG_CMD_IMI
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_LOADS
#define CONFIG_CMD_LOADB
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_MISC
#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
#define CONFIG_CMD_RUN
#define CONFIG_CMD_SAVES


/*------------------------------------------------------------------------
 * COMPACT FLASH
 *----------------------------------------------------------------------*/
#if defined(CONFIG_CMD_IDE)
#define CONFIG_IDE_PREINIT			/* Implement id_preinit	*/
#define CONFIG_SYS_IDE_MAXBUS		1		/* 1 IDE bus		*/
#define CONFIG_SYS_IDE_MAXDEVICE	1		/* 1 drive per IDE bus	*/

#define CONFIG_SYS_ATA_BASE_ADDR	0x00900800	/* ATA base addr	*/
#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000		/* IDE0 offset		*/
#define CONFIG_SYS_ATA_DATA_OFFSET	0x0040		/* Data IO offset	*/
#define CONFIG_SYS_ATA_REG_OFFSET	0x0040		/* Register offset	*/
#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100		/* Alternate reg offset	*/
#define CONFIG_SYS_ATA_STRIDE          4		/* Width betwix addrs	*/
#define CONFIG_DOS_PARTITION

/* Board-specific cf regs */
#define CONFIG_SYS_CF_PRESENT		0x00900880	/* CF Present PIO base	*/
#define CONFIG_SYS_CF_POWER		0x00900890	/* CF Power FET PIO base*/
#define CONFIG_SYS_CF_ATASEL		0x009008a0	/* CF ATASEL PIO base	*/

#endif

/*------------------------------------------------------------------------
 * JFFS2
 *----------------------------------------------------------------------*/
#if defined(CONFIG_CMD_JFFS2)
#define CONFIG_SYS_JFFS_CUSTOM_PART			/* board defined part	*/
#endif

/*------------------------------------------------------------------------
 * MISC
 *----------------------------------------------------------------------*/
#define CONFIG_SYS_LONGHELP				/* Provide extended help*/
#define CONFIG_SYS_PROMPT		"==> "		/* Command prompt	*/
#define CONFIG_SYS_CBSIZE		256		/* Console I/O buf size */
#define CONFIG_SYS_MAXARGS		16		/* Max command args	*/
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot arg buf size	*/
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */
#define CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_SDRAM_BASE	/* Default load address */
#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE	/* Start addr for test	*/
#define CONFIG_SYS_MEMTEST_END		CONFIG_SYS_INIT_SP - 0x00020000

#define CONFIG_SYS_HUSH_PARSER

#endif	/* __CONFIG_H */