dts/upstream/Bindings/pci/mvebu-pci.txt

* Marvell EBU PCIe interfaces

Mandatory properties:

- compatible: one of the following values:
    marvell,armada-370-pcie
    marvell,armada-xp-pcie
    marvell,dove-pcie
    marvell,kirkwood-pcie
- #address-cells, set to <3>
- #size-cells, set to <2>
- #interrupt-cells, set to <1>
- bus-range: PCI bus numbers covered
- device_type, set to "pci"
- ranges: ranges describing the MMIO registers to control the PCIe
  interfaces, and ranges describing the MBus windows needed to access
  the memory and I/O regions of each PCIe interface.
- msi-parent: Link to the hardware entity that serves as the Message
  Signaled Interrupt controller for this PCI controller.

The ranges describing the MMIO registers have the following layout:

    0x82000000 0 r MBUS_ID(0xf0, 0x01) r 0 s

where:

  * r is a 32-bits value that gives the offset of the MMIO
  registers of this PCIe interface, from the base of the internal
  registers.

  * s is a 32-bits value that give the size of this MMIO
  registers area. This range entry translates the '0x82000000 0 r' PCI
  address into the 'MBUS_ID(0xf0, 0x01) r' CPU address, which is part
  of the internal register window (as identified by MBUS_ID(0xf0,
  0x01)).

The ranges describing the MBus windows have the following layout:

    0x8t000000 s 0     MBUS_ID(w, a) 0 1 0

where:

   * t is the type of the MBus window (as defined by the standard PCI DT
   bindings), 1 for I/O and 2 for memory.

   * s is the PCI slot that corresponds to this PCIe interface

   * w is the 'target ID' value for the MBus window

   * a the 'attribute' value for the MBus window.

Since the location and size of the different MBus windows is not fixed in
hardware, and only determined in runtime, those ranges cover the full first
4 GB of the physical address space, and do not translate into a valid CPU
address.

In addition, the device tree node must have sub-nodes describing each
PCIe interface, having the following mandatory properties:

- reg: used only for interrupt mapping, so only the first four bytes
  are used to refer to the correct bus number and device number.
- assigned-addresses: reference to the MMIO registers used to control
  this PCIe interface.
- clocks: the clock associated to this PCIe interface
- marvell,pcie-port: the physical PCIe port number
- status: either "disabled" or "okay"
- device_type, set to "pci"
- #address-cells, set to <3>
- #size-cells, set to <2>
- #interrupt-cells, set to <1>
- ranges, translating the MBus windows ranges of the parent node into
  standard PCI addresses.
- interrupt-map-mask and interrupt-map, standard PCI properties to
  define the mapping of the PCIe interface to interrupt numbers.

and the following optional properties:
- marvell,pcie-lane: the physical PCIe lane number, for ports having
  multiple lanes. If this property is not found, we assume that the
  value is 0.
- num-lanes: number of SerDes PCIe lanes for this link (1 or 4)
- reset-gpios: optional GPIO to PERST#
- reset-delay-us: delay in us to wait after reset de-assertion, if not
  specified will default to 100ms, as required by the PCIe specification.
- interrupt-names: list of interrupt names, supported are:
   - "intx" - interrupt line triggered by one of the legacy interrupt
- interrupts or interrupts-extended: List of the interrupt sources which
  corresponding to the "interrupt-names". If non-empty then also additional
  'interrupt-controller' subnode must be defined.

Example:

pcie-controller {
	compatible = "marvell,armada-xp-pcie";
	device_type = "pci";

	#address-cells = <3>;
	#size-cells = <2>;

	bus-range = <0x00 0xff>;
	msi-parent = <&mpic>;

	ranges =
	       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000	/* Port 0.0 registers */
		0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000	/* Port 2.0 registers */
		0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000	/* Port 0.1 registers */
		0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000	/* Port 0.2 registers */
		0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000	/* Port 0.3 registers */
		0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000	/* Port 1.0 registers */
		0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000	/* Port 3.0 registers */
		0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000	/* Port 1.1 registers */
		0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000	/* Port 1.2 registers */
		0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000	/* Port 1.3 registers */
		0x82000000 0x1 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
		0x81000000 0x1 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO  */
		0x82000000 0x2 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */
		0x81000000 0x2 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 0.1 IO  */
		0x82000000 0x3 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 0.2 MEM */
		0x81000000 0x3 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO  */
		0x82000000 0x4 0     MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */
		0x81000000 0x4 0     MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO  */

		0x82000000 0x5 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
		0x81000000 0x5 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO  */
		0x82000000 0x6 0     MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */
		0x81000000 0x6 0     MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO  */
		0x82000000 0x7 0     MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */
		0x81000000 0x7 0     MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO  */
		0x82000000 0x8 0     MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */
		0x81000000 0x8 0     MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO  */

		0x82000000 0x9 0     MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */
		0x81000000 0x9 0     MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO  */

		0x82000000 0xa 0     MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */
		0x81000000 0xa 0     MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO  */>;

	pcie@1,0 {
		device_type = "pci";
		assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
		reg = <0x0800 0 0 0 0>;
		#address-cells = <3>;
		#size-cells = <2>;
		#interrupt-cells = <1>;
		ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
			  0x81000000 0 0 0x81000000 0x1 0 1 0>;
		interrupt-map-mask = <0 0 0 0>;
		interrupt-map = <0 0 0 0 &mpic 58>;
		marvell,pcie-port = <0>;
		marvell,pcie-lane = <0>;
		num-lanes = <1>;
		/* low-active PERST# reset on GPIO 25 */
		reset-gpios = <&gpio0 25 1>;
		/* wait 20ms for device settle after reset deassertion */
		reset-delay-us = <20000>;
		clocks = <&gateclk 5>;
	};

	pcie@2,0 {
		device_type = "pci";
		assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
		reg = <0x1000 0 0 0 0>;
		#address-cells = <3>;
		#size-cells = <2>;
		#interrupt-cells = <1>;
		ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
			  0x81000000 0 0 0x81000000 0x2 0 1 0>;
		interrupt-map-mask = <0 0 0 0>;
		interrupt-map = <0 0 0 0 &mpic 59>;
		marvell,pcie-port = <0>;
		marvell,pcie-lane = <1>;
		num-lanes = <1>;
		clocks = <&gateclk 6>;
	};

	pcie@3,0 {
		device_type = "pci";
		assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
		reg = <0x1800 0 0 0 0>;
		#address-cells = <3>;
		#size-cells = <2>;
		#interrupt-cells = <1>;
		ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
			  0x81000000 0 0 0x81000000 0x3 0 1 0>;
		interrupt-map-mask = <0 0 0 0>;
		interrupt-map = <0 0 0 0 &mpic 60>;
		marvell,pcie-port = <0>;
		marvell,pcie-lane = <2>;
		num-lanes = <1>;
		clocks = <&gateclk 7>;
	};

	pcie@4,0 {
		device_type = "pci";
		assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
		reg = <0x2000 0 0 0 0>;
		#address-cells = <3>;
		#size-cells = <2>;
		#interrupt-cells = <1>;
		ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
			  0x81000000 0 0 0x81000000 0x4 0 1 0>;
		interrupt-map-mask = <0 0 0 0>;
		interrupt-map = <0 0 0 0 &mpic 61>;
		marvell,pcie-port = <0>;
		marvell,pcie-lane = <3>;
		num-lanes = <1>;
		clocks = <&gateclk 8>;
	};

	pcie@5,0 {
		device_type = "pci";
		assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
		reg = <0x2800 0 0 0 0>;
		#address-cells = <3>;
		#size-cells = <2>;
		#interrupt-cells = <1>;
		ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
			  0x81000000 0 0 0x81000000 0x5 0 1 0>;
		interrupt-map-mask = <0 0 0 0>;
		interrupt-map = <0 0 0 0 &mpic 62>;
		marvell,pcie-port = <1>;
		marvell,pcie-lane = <0>;
		num-lanes = <1>;
		clocks = <&gateclk 9>;
	};

	pcie@6,0 {
		device_type = "pci";
		assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
		reg = <0x3000 0 0 0 0>;
		#address-cells = <3>;
		#size-cells = <2>;
		#interrupt-cells = <1>;
		ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
			  0x81000000 0 0 0x81000000 0x6 0 1 0>;
		interrupt-map-mask = <0 0 0 0>;
		interrupt-map = <0 0 0 0 &mpic 63>;
		marvell,pcie-port = <1>;
		marvell,pcie-lane = <1>;
		num-lanes = <1>;
		clocks = <&gateclk 10>;
	};

	pcie@7,0 {
		device_type = "pci";
		assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
		reg = <0x3800 0 0 0 0>;
		#address-cells = <3>;
		#size-cells = <2>;
		#interrupt-cells = <1>;
		ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
			  0x81000000 0 0 0x81000000 0x7 0 1 0>;
		interrupt-map-mask = <0 0 0 0>;
		interrupt-map = <0 0 0 0 &mpic 64>;
		marvell,pcie-port = <1>;
		marvell,pcie-lane = <2>;
		num-lanes = <1>;
		clocks = <&gateclk 11>;
	};

	pcie@8,0 {
		device_type = "pci";
		assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
		reg = <0x4000 0 0 0 0>;
		#address-cells = <3>;
		#size-cells = <2>;
		#interrupt-cells = <1>;
		ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
			  0x81000000 0 0 0x81000000 0x8 0 1 0>;
		interrupt-map-mask = <0 0 0 0>;
		interrupt-map = <0 0 0 0 &mpic 65>;
		marvell,pcie-port = <1>;
		marvell,pcie-lane = <3>;
		num-lanes = <1>;
		clocks = <&gateclk 12>;
	};

	pcie@9,0 {
		device_type = "pci";
		assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
		reg = <0x4800 0 0 0 0>;
		#address-cells = <3>;
		#size-cells = <2>;
		#interrupt-cells = <1>;
		ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
			  0x81000000 0 0 0x81000000 0x9 0 1 0>;
		interrupt-map-mask = <0 0 0 0>;
		interrupt-map = <0 0 0 0 &mpic 99>;
		marvell,pcie-port = <2>;
		marvell,pcie-lane = <0>;
		num-lanes = <1>;
		clocks = <&gateclk 26>;
	};

	pcie@a,0 {
		device_type = "pci";
		assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
		reg = <0x5000 0 0 0 0>;
		#address-cells = <3>;
		#size-cells = <2>;
		#interrupt-cells = <1>;
		ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0
			  0x81000000 0 0 0x81000000 0xa 0 1 0>;
		interrupt-map-mask = <0 0 0 0>;
		interrupt-map = <0 0 0 0 &mpic 103>;
		marvell,pcie-port = <3>;
		marvell,pcie-lane = <0>;
		num-lanes = <1>;
		clocks = <&gateclk 27>;
	};
};