Simon Glass | dec49b7 | 2016-03-11 22:07:30 -0700 | [diff] [blame] | 1 | /* |
| 2 | * From coreboot src/soc/intel/broadwell/igd.c |
| 3 | * |
| 4 | * Copyright (C) 2016 Google, Inc |
| 5 | * |
| 6 | * SPDX-License-Identifier: GPL-2.0 |
| 7 | */ |
| 8 | |
| 9 | #include <common.h> |
| 10 | #include <bios_emul.h> |
| 11 | #include <dm.h> |
| 12 | #include <pci_rom.h> |
| 13 | #include <vbe.h> |
| 14 | #include <video.h> |
| 15 | #include <video_fb.h> |
| 16 | #include <asm/cpu.h> |
| 17 | #include <asm/intel_regs.h> |
| 18 | #include <asm/io.h> |
| 19 | #include <asm/mtrr.h> |
| 20 | #include <asm/arch/cpu.h> |
| 21 | #include <asm/arch/iomap.h> |
| 22 | #include <asm/arch/pch.h> |
| 23 | #include <linux/log2.h> |
| 24 | #include "i915_reg.h" |
| 25 | |
| 26 | struct broadwell_igd_priv { |
| 27 | GraphicDevice ctfb; |
| 28 | u8 *regs; |
| 29 | }; |
| 30 | |
| 31 | struct broadwell_igd_plat { |
| 32 | u32 dp_hotplug[3]; |
| 33 | |
| 34 | int port_select; |
| 35 | int power_up_delay; |
| 36 | int power_backlight_on_delay; |
| 37 | int power_down_delay; |
| 38 | int power_backlight_off_delay; |
| 39 | int power_cycle_delay; |
| 40 | int cpu_backlight; |
| 41 | int pch_backlight; |
| 42 | int cdclk; |
| 43 | int pre_graphics_delay; |
| 44 | }; |
| 45 | |
| 46 | #define GT_RETRY 1000 |
| 47 | #define GT_CDCLK_337 0 |
| 48 | #define GT_CDCLK_450 1 |
| 49 | #define GT_CDCLK_540 2 |
| 50 | #define GT_CDCLK_675 3 |
| 51 | |
| 52 | u32 board_map_oprom_vendev(u32 vendev) |
| 53 | { |
| 54 | return SA_IGD_OPROM_VENDEV; |
| 55 | } |
| 56 | |
| 57 | static int poll32(u8 *addr, uint mask, uint value) |
| 58 | { |
| 59 | ulong start; |
| 60 | |
| 61 | start = get_timer(0); |
| 62 | debug("%s: addr %p = %x\n", __func__, addr, readl(addr)); |
| 63 | while ((readl(addr) & mask) != value) { |
| 64 | if (get_timer(start) > GT_RETRY) { |
| 65 | debug("poll32: timeout: %x\n", readl(addr)); |
| 66 | return -ETIMEDOUT; |
| 67 | } |
| 68 | } |
| 69 | |
| 70 | return 0; |
| 71 | } |
| 72 | |
| 73 | static int haswell_early_init(struct udevice *dev) |
| 74 | { |
| 75 | struct broadwell_igd_priv *priv = dev_get_priv(dev); |
| 76 | u8 *regs = priv->regs; |
| 77 | int ret; |
| 78 | |
| 79 | /* Enable Force Wake */ |
| 80 | writel(0x00000020, regs + 0xa180); |
| 81 | writel(0x00010001, regs + 0xa188); |
| 82 | ret = poll32(regs + 0x130044, 1, 1); |
| 83 | if (ret) |
| 84 | goto err; |
| 85 | |
| 86 | /* Enable Counters */ |
| 87 | setbits_le32(regs + 0xa248, 0x00000016); |
| 88 | |
| 89 | /* GFXPAUSE settings */ |
| 90 | writel(0x00070020, regs + 0xa000); |
| 91 | |
| 92 | /* ECO Settings */ |
| 93 | clrsetbits_le32(regs + 0xa180, ~0xff3fffff, 0x15000000); |
| 94 | |
| 95 | /* Enable DOP Clock Gating */ |
| 96 | writel(0x000003fd, regs + 0x9424); |
| 97 | |
| 98 | /* Enable Unit Level Clock Gating */ |
| 99 | writel(0x00000080, regs + 0x9400); |
| 100 | writel(0x40401000, regs + 0x9404); |
| 101 | writel(0x00000000, regs + 0x9408); |
| 102 | writel(0x02000001, regs + 0x940c); |
| 103 | |
| 104 | /* |
| 105 | * RC6 Settings |
| 106 | */ |
| 107 | |
| 108 | /* Wake Rate Limits */ |
| 109 | setbits_le32(regs + 0xa090, 0x00000000); |
| 110 | setbits_le32(regs + 0xa098, 0x03e80000); |
| 111 | setbits_le32(regs + 0xa09c, 0x00280000); |
| 112 | setbits_le32(regs + 0xa0a8, 0x0001e848); |
| 113 | setbits_le32(regs + 0xa0ac, 0x00000019); |
| 114 | |
| 115 | /* Render/Video/Blitter Idle Max Count */ |
| 116 | writel(0x0000000a, regs + 0x02054); |
| 117 | writel(0x0000000a, regs + 0x12054); |
| 118 | writel(0x0000000a, regs + 0x22054); |
| 119 | writel(0x0000000a, regs + 0x1a054); |
| 120 | |
| 121 | /* RC Sleep / RCx Thresholds */ |
| 122 | setbits_le32(regs + 0xa0b0, 0x00000000); |
| 123 | setbits_le32(regs + 0xa0b4, 0x000003e8); |
| 124 | setbits_le32(regs + 0xa0b8, 0x0000c350); |
| 125 | |
| 126 | /* RP Settings */ |
| 127 | setbits_le32(regs + 0xa010, 0x000f4240); |
| 128 | setbits_le32(regs + 0xa014, 0x12060000); |
| 129 | setbits_le32(regs + 0xa02c, 0x0000e808); |
| 130 | setbits_le32(regs + 0xa030, 0x0003bd08); |
| 131 | setbits_le32(regs + 0xa068, 0x000101d0); |
| 132 | setbits_le32(regs + 0xa06c, 0x00055730); |
| 133 | setbits_le32(regs + 0xa070, 0x0000000a); |
| 134 | |
| 135 | /* RP Control */ |
| 136 | writel(0x00000b92, regs + 0xa024); |
| 137 | |
| 138 | /* HW RC6 Control */ |
| 139 | writel(0x88040000, regs + 0xa090); |
| 140 | |
| 141 | /* Video Frequency Request */ |
| 142 | writel(0x08000000, regs + 0xa00c); |
| 143 | |
| 144 | /* Set RC6 VIDs */ |
| 145 | ret = poll32(regs + 0x138124, (1 << 31), 0); |
| 146 | if (ret) |
| 147 | goto err; |
| 148 | writel(0, regs + 0x138128); |
| 149 | writel(0x80000004, regs + 0x138124); |
| 150 | ret = poll32(regs + 0x138124, (1 << 31), 0); |
| 151 | if (ret) |
| 152 | goto err; |
| 153 | |
| 154 | /* Enable PM Interrupts */ |
| 155 | writel(0x03000076, regs + 0x4402c); |
| 156 | |
| 157 | /* Enable RC6 in idle */ |
| 158 | writel(0x00040000, regs + 0xa094); |
| 159 | |
| 160 | return 0; |
| 161 | err: |
| 162 | debug("%s: ret=%d\n", __func__, ret); |
| 163 | return ret; |
| 164 | }; |
| 165 | |
| 166 | static int haswell_late_init(struct udevice *dev) |
| 167 | { |
| 168 | struct broadwell_igd_priv *priv = dev_get_priv(dev); |
| 169 | u8 *regs = priv->regs; |
| 170 | int ret; |
| 171 | |
| 172 | /* Lock settings */ |
| 173 | setbits_le32(regs + 0x0a248, (1 << 31)); |
| 174 | setbits_le32(regs + 0x0a004, (1 << 4)); |
| 175 | setbits_le32(regs + 0x0a080, (1 << 2)); |
| 176 | setbits_le32(regs + 0x0a180, (1 << 31)); |
| 177 | |
| 178 | /* Disable Force Wake */ |
| 179 | writel(0x00010000, regs + 0xa188); |
| 180 | ret = poll32(regs + 0x130044, 1, 0); |
| 181 | if (ret) |
| 182 | goto err; |
| 183 | writel(0x00000001, regs + 0xa188); |
| 184 | |
| 185 | /* Enable power well for DP and Audio */ |
| 186 | setbits_le32(regs + 0x45400, (1 << 31)); |
| 187 | ret = poll32(regs + 0x45400, 1 << 30, 1 << 30); |
| 188 | if (ret) |
| 189 | goto err; |
| 190 | |
| 191 | return 0; |
| 192 | err: |
| 193 | debug("%s: ret=%d\n", __func__, ret); |
| 194 | return ret; |
| 195 | }; |
| 196 | |
| 197 | static int broadwell_early_init(struct udevice *dev) |
| 198 | { |
| 199 | struct broadwell_igd_priv *priv = dev_get_priv(dev); |
| 200 | u8 *regs = priv->regs; |
| 201 | int ret; |
| 202 | |
| 203 | /* Enable Force Wake */ |
| 204 | writel(0x00010001, regs + 0xa188); |
| 205 | ret = poll32(regs + 0x130044, 1, 1); |
| 206 | if (ret) |
| 207 | goto err; |
| 208 | |
| 209 | /* Enable push bus metric control and shift */ |
| 210 | writel(0x00000004, regs + 0xa248); |
| 211 | writel(0x000000ff, regs + 0xa250); |
| 212 | writel(0x00000010, regs + 0xa25c); |
| 213 | |
| 214 | /* GFXPAUSE settings (set based on stepping) */ |
| 215 | |
| 216 | /* ECO Settings */ |
| 217 | writel(0x45200000, regs + 0xa180); |
| 218 | |
| 219 | /* Enable DOP Clock Gating */ |
| 220 | writel(0x000000fd, regs + 0x9424); |
| 221 | |
| 222 | /* Enable Unit Level Clock Gating */ |
| 223 | writel(0x00000000, regs + 0x9400); |
| 224 | writel(0x40401000, regs + 0x9404); |
| 225 | writel(0x00000000, regs + 0x9408); |
| 226 | writel(0x02000001, regs + 0x940c); |
| 227 | writel(0x0000000a, regs + 0x1a054); |
| 228 | |
| 229 | /* Video Frequency Request */ |
| 230 | writel(0x08000000, regs + 0xa00c); |
| 231 | |
| 232 | writel(0x00000009, regs + 0x138158); |
| 233 | writel(0x0000000d, regs + 0x13815c); |
| 234 | |
| 235 | /* |
| 236 | * RC6 Settings |
| 237 | */ |
| 238 | |
| 239 | /* Wake Rate Limits */ |
| 240 | clrsetbits_le32(regs + 0x0a090, ~0, 0); |
| 241 | setbits_le32(regs + 0x0a098, 0x03e80000); |
| 242 | setbits_le32(regs + 0x0a09c, 0x00280000); |
| 243 | setbits_le32(regs + 0x0a0a8, 0x0001e848); |
| 244 | setbits_le32(regs + 0x0a0ac, 0x00000019); |
| 245 | |
| 246 | /* Render/Video/Blitter Idle Max Count */ |
| 247 | writel(0x0000000a, regs + 0x02054); |
| 248 | writel(0x0000000a, regs + 0x12054); |
| 249 | writel(0x0000000a, regs + 0x22054); |
| 250 | |
| 251 | /* RC Sleep / RCx Thresholds */ |
| 252 | setbits_le32(regs + 0x0a0b0, 0x00000000); |
| 253 | setbits_le32(regs + 0x0a0b8, 0x00000271); |
| 254 | |
| 255 | /* RP Settings */ |
| 256 | setbits_le32(regs + 0x0a010, 0x000f4240); |
| 257 | setbits_le32(regs + 0x0a014, 0x12060000); |
| 258 | setbits_le32(regs + 0x0a02c, 0x0000e808); |
| 259 | setbits_le32(regs + 0x0a030, 0x0003bd08); |
| 260 | setbits_le32(regs + 0x0a068, 0x000101d0); |
| 261 | setbits_le32(regs + 0x0a06c, 0x00055730); |
| 262 | setbits_le32(regs + 0x0a070, 0x0000000a); |
| 263 | setbits_le32(regs + 0x0a168, 0x00000006); |
| 264 | |
| 265 | /* RP Control */ |
| 266 | writel(0x00000b92, regs + 0xa024); |
| 267 | |
| 268 | /* HW RC6 Control */ |
| 269 | writel(0x90040000, regs + 0xa090); |
| 270 | |
| 271 | /* Set RC6 VIDs */ |
| 272 | ret = poll32(regs + 0x138124, (1 << 31), 0); |
| 273 | if (ret) |
| 274 | goto err; |
| 275 | writel(0, regs + 0x138128); |
| 276 | writel(0x80000004, regs + 0x138124); |
| 277 | ret = poll32(regs + 0x138124, (1 << 31), 0); |
| 278 | if (ret) |
| 279 | goto err; |
| 280 | |
| 281 | /* Enable PM Interrupts */ |
| 282 | writel(0x03000076, regs + 0x4402c); |
| 283 | |
| 284 | /* Enable RC6 in idle */ |
| 285 | writel(0x00040000, regs + 0xa094); |
| 286 | |
| 287 | return 0; |
| 288 | err: |
| 289 | debug("%s: ret=%d\n", __func__, ret); |
| 290 | return ret; |
| 291 | } |
| 292 | |
| 293 | static int broadwell_late_init(struct udevice *dev) |
| 294 | { |
| 295 | struct broadwell_igd_priv *priv = dev_get_priv(dev); |
| 296 | u8 *regs = priv->regs; |
| 297 | int ret; |
| 298 | |
| 299 | /* Lock settings */ |
| 300 | setbits_le32(regs + 0x0a248, 1 << 31); |
| 301 | setbits_le32(regs + 0x0a000, 1 << 18); |
| 302 | setbits_le32(regs + 0x0a180, 1 << 31); |
| 303 | |
| 304 | /* Disable Force Wake */ |
| 305 | writel(0x00010000, regs + 0xa188); |
| 306 | ret = poll32(regs + 0x130044, 1, 0); |
| 307 | if (ret) |
| 308 | goto err; |
| 309 | |
| 310 | /* Enable power well for DP and Audio */ |
| 311 | setbits_le32(regs + 0x45400, 1 << 31); |
| 312 | ret = poll32(regs + 0x45400, 1 << 30, 1 << 30); |
| 313 | if (ret) |
| 314 | goto err; |
| 315 | |
| 316 | return 0; |
| 317 | err: |
| 318 | debug("%s: ret=%d\n", __func__, ret); |
| 319 | return ret; |
| 320 | }; |
| 321 | |
| 322 | |
| 323 | static unsigned long gtt_read(struct broadwell_igd_priv *priv, |
| 324 | unsigned long reg) |
| 325 | { |
| 326 | u32 val; |
| 327 | |
| 328 | val = readl(priv->regs + reg); |
| 329 | return val; |
| 330 | } |
| 331 | |
| 332 | static void gtt_write(struct broadwell_igd_priv *priv, unsigned long reg, |
| 333 | unsigned long data) |
| 334 | { |
| 335 | writel(data, priv->regs + reg); |
| 336 | } |
| 337 | |
| 338 | static inline void gtt_clrsetbits(struct broadwell_igd_priv *priv, u32 reg, |
| 339 | u32 bic, u32 or) |
| 340 | { |
| 341 | clrsetbits_le32(priv->regs + reg, bic, or); |
| 342 | } |
| 343 | |
| 344 | static int gtt_poll(struct broadwell_igd_priv *priv, u32 reg, u32 mask, |
| 345 | u32 value) |
| 346 | { |
| 347 | unsigned try = GT_RETRY; |
| 348 | u32 data; |
| 349 | |
| 350 | while (try--) { |
| 351 | data = gtt_read(priv, reg); |
| 352 | if ((data & mask) == value) |
| 353 | return 0; |
| 354 | udelay(10); |
| 355 | } |
| 356 | |
| 357 | debug("GT init timeout\n"); |
| 358 | return -ETIMEDOUT; |
| 359 | } |
| 360 | |
| 361 | static void igd_setup_panel(struct udevice *dev) |
| 362 | { |
| 363 | struct broadwell_igd_plat *plat = dev_get_platdata(dev); |
| 364 | struct broadwell_igd_priv *priv = dev_get_priv(dev); |
| 365 | u32 reg32; |
| 366 | |
| 367 | /* Setup Digital Port Hotplug */ |
| 368 | reg32 = (plat->dp_hotplug[0] & 0x7) << 2; |
| 369 | reg32 |= (plat->dp_hotplug[1] & 0x7) << 10; |
| 370 | reg32 |= (plat->dp_hotplug[2] & 0x7) << 18; |
| 371 | gtt_write(priv, PCH_PORT_HOTPLUG, reg32); |
| 372 | |
| 373 | /* Setup Panel Power On Delays */ |
| 374 | reg32 = (plat->port_select & 0x3) << 30; |
| 375 | reg32 |= (plat->power_up_delay & 0x1fff) << 16; |
| 376 | reg32 |= (plat->power_backlight_on_delay & 0x1fff); |
| 377 | gtt_write(priv, PCH_PP_ON_DELAYS, reg32); |
| 378 | |
| 379 | /* Setup Panel Power Off Delays */ |
| 380 | reg32 = (plat->power_down_delay & 0x1fff) << 16; |
| 381 | reg32 |= (plat->power_backlight_off_delay & 0x1fff); |
| 382 | gtt_write(priv, PCH_PP_OFF_DELAYS, reg32); |
| 383 | |
| 384 | /* Setup Panel Power Cycle Delay */ |
| 385 | if (plat->power_cycle_delay) { |
| 386 | reg32 = gtt_read(priv, PCH_PP_DIVISOR); |
| 387 | reg32 &= ~0xff; |
| 388 | reg32 |= plat->power_cycle_delay & 0xff; |
| 389 | gtt_write(priv, PCH_PP_DIVISOR, reg32); |
| 390 | } |
| 391 | |
| 392 | /* Enable Backlight if needed */ |
| 393 | if (plat->cpu_backlight) { |
| 394 | gtt_write(priv, BLC_PWM_CPU_CTL2, BLC_PWM2_ENABLE); |
| 395 | gtt_write(priv, BLC_PWM_CPU_CTL, plat->cpu_backlight); |
| 396 | } |
| 397 | if (plat->pch_backlight) { |
| 398 | gtt_write(priv, BLC_PWM_PCH_CTL1, BLM_PCH_PWM_ENABLE); |
| 399 | gtt_write(priv, BLC_PWM_PCH_CTL2, plat->pch_backlight); |
| 400 | } |
| 401 | } |
| 402 | |
| 403 | static int igd_cdclk_init_haswell(struct udevice *dev) |
| 404 | { |
| 405 | struct broadwell_igd_plat *plat = dev_get_platdata(dev); |
| 406 | struct broadwell_igd_priv *priv = dev_get_priv(dev); |
| 407 | int cdclk = plat->cdclk; |
| 408 | u16 devid; |
| 409 | int gpu_is_ulx = 0; |
| 410 | u32 dpdiv, lpcll; |
| 411 | int ret; |
| 412 | |
| 413 | dm_pci_read_config16(dev, PCI_DEVICE_ID, &devid); |
| 414 | |
| 415 | /* Check for ULX GT1 or GT2 */ |
| 416 | if (devid == 0x0a0e || devid == 0x0a1e) |
| 417 | gpu_is_ulx = 1; |
| 418 | |
| 419 | /* 675MHz is not supported on haswell */ |
| 420 | if (cdclk == GT_CDCLK_675) |
| 421 | cdclk = GT_CDCLK_337; |
| 422 | |
| 423 | /* If CD clock is fixed or ULT then set to 450MHz */ |
| 424 | if ((gtt_read(priv, 0x42014) & 0x1000000) || cpu_is_ult()) |
| 425 | cdclk = GT_CDCLK_450; |
| 426 | |
| 427 | /* 540MHz is not supported on ULX */ |
| 428 | if (gpu_is_ulx && cdclk == GT_CDCLK_540) |
| 429 | cdclk = GT_CDCLK_337; |
| 430 | |
| 431 | /* 337.5MHz is not supported on non-ULT/ULX */ |
| 432 | if (!gpu_is_ulx && !cpu_is_ult() && cdclk == GT_CDCLK_337) |
| 433 | cdclk = GT_CDCLK_450; |
| 434 | |
| 435 | /* Set variables based on CD Clock setting */ |
| 436 | switch (cdclk) { |
| 437 | case GT_CDCLK_337: |
| 438 | dpdiv = 169; |
| 439 | lpcll = (1 << 26); |
| 440 | break; |
| 441 | case GT_CDCLK_450: |
| 442 | dpdiv = 225; |
| 443 | lpcll = 0; |
| 444 | break; |
| 445 | case GT_CDCLK_540: |
| 446 | dpdiv = 270; |
| 447 | lpcll = (1 << 26); |
| 448 | break; |
| 449 | default: |
| 450 | ret = -EDOM; |
| 451 | goto err; |
| 452 | } |
| 453 | |
| 454 | /* Set LPCLL_CTL CD Clock Frequency Select */ |
| 455 | gtt_clrsetbits(priv, 0x130040, ~0xf3ffffff, lpcll); |
| 456 | |
| 457 | /* ULX: Inform power controller of selected frequency */ |
| 458 | if (gpu_is_ulx) { |
| 459 | if (cdclk == GT_CDCLK_450) |
| 460 | gtt_write(priv, 0x138128, 0x00000000); /* 450MHz */ |
| 461 | else |
| 462 | gtt_write(priv, 0x138128, 0x00000001); /* 337.5MHz */ |
| 463 | gtt_write(priv, 0x13812c, 0x00000000); |
| 464 | gtt_write(priv, 0x138124, 0x80000017); |
| 465 | } |
| 466 | |
| 467 | /* Set CPU DP AUX 2X bit clock dividers */ |
| 468 | gtt_clrsetbits(priv, 0x64010, ~0xfffff800, dpdiv); |
| 469 | gtt_clrsetbits(priv, 0x64810, ~0xfffff800, dpdiv); |
| 470 | |
| 471 | return 0; |
| 472 | err: |
| 473 | debug("%s: ret=%d\n", __func__, ret); |
| 474 | return ret; |
| 475 | } |
| 476 | |
| 477 | static int igd_cdclk_init_broadwell(struct udevice *dev) |
| 478 | { |
| 479 | struct broadwell_igd_plat *plat = dev_get_platdata(dev); |
| 480 | struct broadwell_igd_priv *priv = dev_get_priv(dev); |
| 481 | int cdclk = plat->cdclk; |
| 482 | u32 dpdiv, lpcll, pwctl, cdset; |
| 483 | int ret; |
| 484 | |
| 485 | /* Inform power controller of upcoming frequency change */ |
| 486 | gtt_write(priv, 0x138128, 0); |
| 487 | gtt_write(priv, 0x13812c, 0); |
| 488 | gtt_write(priv, 0x138124, 0x80000018); |
| 489 | |
| 490 | /* Poll GT driver mailbox for run/busy clear */ |
| 491 | if (gtt_poll(priv, 0x138124, 1 << 31, 0 << 31)) |
| 492 | cdclk = GT_CDCLK_450; |
| 493 | |
| 494 | if (gtt_read(priv, 0x42014) & 0x1000000) { |
| 495 | /* If CD clock is fixed then set to 450MHz */ |
| 496 | cdclk = GT_CDCLK_450; |
| 497 | } else { |
| 498 | /* Program CD clock to highest supported freq */ |
| 499 | if (cpu_is_ult()) |
| 500 | cdclk = GT_CDCLK_540; |
| 501 | else |
| 502 | cdclk = GT_CDCLK_675; |
| 503 | } |
| 504 | |
| 505 | /* CD clock frequency 675MHz not supported on ULT */ |
| 506 | if (cpu_is_ult() && cdclk == GT_CDCLK_675) |
| 507 | cdclk = GT_CDCLK_540; |
| 508 | |
| 509 | /* Set variables based on CD Clock setting */ |
| 510 | switch (cdclk) { |
| 511 | case GT_CDCLK_337: |
| 512 | cdset = 337; |
| 513 | lpcll = (1 << 27); |
| 514 | pwctl = 2; |
| 515 | dpdiv = 169; |
| 516 | break; |
| 517 | case GT_CDCLK_450: |
| 518 | cdset = 449; |
| 519 | lpcll = 0; |
| 520 | pwctl = 0; |
| 521 | dpdiv = 225; |
| 522 | break; |
| 523 | case GT_CDCLK_540: |
| 524 | cdset = 539; |
| 525 | lpcll = (1 << 26); |
| 526 | pwctl = 1; |
| 527 | dpdiv = 270; |
| 528 | break; |
| 529 | case GT_CDCLK_675: |
| 530 | cdset = 674; |
| 531 | lpcll = (1 << 26) | (1 << 27); |
| 532 | pwctl = 3; |
| 533 | dpdiv = 338; |
| 534 | break; |
| 535 | default: |
| 536 | ret = -EDOM; |
| 537 | goto err; |
| 538 | } |
| 539 | debug("%s: frequency = %d\n", __func__, cdclk); |
| 540 | |
| 541 | /* Set LPCLL_CTL CD Clock Frequency Select */ |
| 542 | gtt_clrsetbits(priv, 0x130040, ~0xf3ffffff, lpcll); |
| 543 | |
| 544 | /* Inform power controller of selected frequency */ |
| 545 | gtt_write(priv, 0x138128, pwctl); |
| 546 | gtt_write(priv, 0x13812c, 0); |
| 547 | gtt_write(priv, 0x138124, 0x80000017); |
| 548 | |
| 549 | /* Program CD Clock Frequency */ |
| 550 | gtt_clrsetbits(priv, 0x46200, ~0xfffffc00, cdset); |
| 551 | |
| 552 | /* Set CPU DP AUX 2X bit clock dividers */ |
| 553 | gtt_clrsetbits(priv, 0x64010, ~0xfffff800, dpdiv); |
| 554 | gtt_clrsetbits(priv, 0x64810, ~0xfffff800, dpdiv); |
| 555 | |
| 556 | return 0; |
| 557 | err: |
| 558 | debug("%s: ret=%d\n", __func__, ret); |
| 559 | return ret; |
| 560 | } |
| 561 | |
| 562 | u8 systemagent_revision(struct udevice *bus) |
| 563 | { |
| 564 | ulong val; |
| 565 | |
| 566 | pci_bus_read_config(bus, PCI_BDF(0, 0, 0), PCI_REVISION_ID, &val, |
| 567 | PCI_SIZE_32); |
| 568 | |
| 569 | return val; |
| 570 | } |
| 571 | |
| 572 | static int igd_pre_init(struct udevice *dev, bool is_broadwell) |
| 573 | { |
| 574 | struct broadwell_igd_plat *plat = dev_get_platdata(dev); |
| 575 | struct broadwell_igd_priv *priv = dev_get_priv(dev); |
| 576 | u32 rp1_gfx_freq; |
| 577 | int ret; |
| 578 | |
| 579 | mdelay(plat->pre_graphics_delay); |
| 580 | |
| 581 | /* Early init steps */ |
| 582 | if (is_broadwell) { |
| 583 | ret = broadwell_early_init(dev); |
| 584 | if (ret) |
| 585 | goto err; |
| 586 | |
| 587 | /* Set GFXPAUSE based on stepping */ |
| 588 | if (cpu_get_stepping() <= (CPUID_BROADWELL_E0 & 0xf) && |
| 589 | systemagent_revision(pci_get_controller(dev)) <= 9) { |
| 590 | gtt_write(priv, 0xa000, 0x300ff); |
| 591 | } else { |
| 592 | gtt_write(priv, 0xa000, 0x30020); |
| 593 | } |
| 594 | } else { |
| 595 | ret = haswell_early_init(dev); |
| 596 | if (ret) |
| 597 | goto err; |
| 598 | } |
| 599 | |
| 600 | /* Set RP1 graphics frequency */ |
| 601 | rp1_gfx_freq = (readl(MCHBAR_REG(0x5998)) >> 8) & 0xff; |
| 602 | gtt_write(priv, 0xa008, rp1_gfx_freq << 24); |
| 603 | |
| 604 | /* Post VBIOS panel setup */ |
| 605 | igd_setup_panel(dev); |
| 606 | |
| 607 | return 0; |
| 608 | err: |
| 609 | debug("%s: ret=%d\n", __func__, ret); |
| 610 | return ret; |
| 611 | } |
| 612 | |
| 613 | static int igd_post_init(struct udevice *dev, bool is_broadwell) |
| 614 | { |
| 615 | int ret; |
| 616 | |
| 617 | /* Late init steps */ |
| 618 | if (is_broadwell) { |
| 619 | ret = igd_cdclk_init_broadwell(dev); |
| 620 | if (ret) |
| 621 | return ret; |
| 622 | ret = broadwell_late_init(dev); |
| 623 | if (ret) |
| 624 | return ret; |
| 625 | } else { |
| 626 | igd_cdclk_init_haswell(dev); |
| 627 | ret = haswell_late_init(dev); |
| 628 | if (ret) |
| 629 | return ret; |
| 630 | } |
| 631 | |
| 632 | return 0; |
| 633 | } |
| 634 | |
| 635 | static int broadwell_igd_int15_handler(void) |
| 636 | { |
| 637 | int res = 0; |
| 638 | |
| 639 | debug("%s: INT15 function %04x!\n", __func__, M.x86.R_AX); |
| 640 | |
| 641 | switch (M.x86.R_AX) { |
| 642 | case 0x5f35: |
| 643 | /* |
| 644 | * Boot Display Device Hook: |
| 645 | * bit 0 = CRT |
| 646 | * bit 1 = TV (eDP) |
| 647 | * bit 2 = EFP |
| 648 | * bit 3 = LFP |
| 649 | * bit 4 = CRT2 |
| 650 | * bit 5 = TV2 (eDP) |
| 651 | * bit 6 = EFP2 |
| 652 | * bit 7 = LFP2 |
| 653 | */ |
| 654 | M.x86.R_AX = 0x005f; |
| 655 | M.x86.R_CX = 0x0000; /* Use video bios default */ |
| 656 | res = 1; |
| 657 | break; |
| 658 | default: |
| 659 | debug("Unknown INT15 function %04x!\n", M.x86.R_AX); |
| 660 | break; |
| 661 | } |
| 662 | |
| 663 | return res; |
| 664 | } |
| 665 | |
| 666 | static int broadwell_igd_probe(struct udevice *dev) |
| 667 | { |
| 668 | struct video_uc_platdata *plat = dev_get_uclass_platdata(dev); |
| 669 | struct video_priv *uc_priv = dev_get_uclass_priv(dev); |
| 670 | struct broadwell_igd_priv *priv = dev_get_priv(dev); |
| 671 | bool is_broadwell; |
| 672 | GraphicDevice *gdev = &priv->ctfb; |
| 673 | int bits_per_pixel; |
| 674 | int ret; |
| 675 | |
| 676 | if (!ll_boot_init()) { |
| 677 | /* |
| 678 | * If we are running from EFI or coreboot, this driver can't |
| 679 | * work. |
| 680 | */ |
| 681 | printf("Not available (previous bootloader prevents it)\n"); |
| 682 | return -EPERM; |
| 683 | } |
| 684 | is_broadwell = cpu_get_family_model() == BROADWELL_FAMILY_ULT; |
| 685 | bootstage_start(BOOTSTAGE_ID_ACCUM_LCD, "vesa display"); |
| 686 | debug("%s: is_broadwell=%d\n", __func__, is_broadwell); |
| 687 | ret = igd_pre_init(dev, is_broadwell); |
| 688 | if (!ret) { |
| 689 | ret = dm_pci_run_vga_bios(dev, broadwell_igd_int15_handler, |
| 690 | PCI_ROM_USE_NATIVE | |
| 691 | PCI_ROM_ALLOW_FALLBACK); |
| 692 | if (ret) { |
| 693 | printf("failed to run video BIOS: %d\n", ret); |
| 694 | ret = -EIO; |
| 695 | } |
| 696 | } |
| 697 | if (!ret) |
| 698 | ret = igd_post_init(dev, is_broadwell); |
| 699 | bootstage_accum(BOOTSTAGE_ID_ACCUM_LCD); |
| 700 | if (ret) |
| 701 | return ret; |
| 702 | |
| 703 | if (vbe_get_video_info(gdev)) { |
| 704 | printf("No video mode configured\n"); |
| 705 | return -ENXIO; |
| 706 | } |
| 707 | |
| 708 | /* Use write-through for the graphics memory, 256MB */ |
| 709 | ret = mtrr_add_request(MTRR_TYPE_WRTHROUGH, gdev->pciBase, 256 << 20); |
| 710 | if (!ret) |
| 711 | ret = mtrr_commit(true); |
| 712 | if (ret && ret != -ENOSYS) { |
| 713 | printf("Failed to add MTRR: Display will be slow (err %d)\n", |
| 714 | ret); |
| 715 | } |
| 716 | |
| 717 | bits_per_pixel = gdev->gdfBytesPP * 8; |
| 718 | sprintf(gdev->modeIdent, "%dx%dx%d", gdev->winSizeX, gdev->winSizeY, |
| 719 | bits_per_pixel); |
| 720 | printf("%s\n", gdev->modeIdent); |
| 721 | uc_priv->xsize = gdev->winSizeX; |
| 722 | uc_priv->ysize = gdev->winSizeY; |
| 723 | uc_priv->bpix = ilog2(bits_per_pixel); |
| 724 | plat->base = gdev->pciBase; |
| 725 | plat->size = gdev->memSize; |
| 726 | debug("fb=%x, size %x, display size=%d %d %d\n", gdev->pciBase, |
| 727 | gdev->memSize, uc_priv->xsize, uc_priv->ysize, uc_priv->bpix); |
| 728 | |
| 729 | return 0; |
| 730 | } |
| 731 | |
| 732 | static int broadwell_igd_ofdata_to_platdata(struct udevice *dev) |
| 733 | { |
| 734 | struct broadwell_igd_plat *plat = dev_get_platdata(dev); |
| 735 | struct broadwell_igd_priv *priv = dev_get_priv(dev); |
| 736 | int node = dev->of_offset; |
| 737 | const void *blob = gd->fdt_blob; |
| 738 | |
| 739 | if (fdtdec_get_int_array(blob, node, "intel,dp-hotplug", |
| 740 | plat->dp_hotplug, |
| 741 | ARRAY_SIZE(plat->dp_hotplug))) |
| 742 | return -EINVAL; |
| 743 | plat->port_select = fdtdec_get_int(blob, node, "intel,port-select", 0); |
| 744 | plat->power_cycle_delay = fdtdec_get_int(blob, node, |
| 745 | "intel,power-cycle-delay", 0); |
| 746 | plat->power_up_delay = fdtdec_get_int(blob, node, |
| 747 | "intel,power-up-delay", 0); |
| 748 | plat->power_down_delay = fdtdec_get_int(blob, node, |
| 749 | "intel,power-down-delay", 0); |
| 750 | plat->power_backlight_on_delay = fdtdec_get_int(blob, node, |
| 751 | "intel,power-backlight-on-delay", 0); |
| 752 | plat->power_backlight_off_delay = fdtdec_get_int(blob, node, |
| 753 | "intel,power-backlight-off-delay", 0); |
| 754 | plat->cpu_backlight = fdtdec_get_int(blob, node, |
| 755 | "intel,cpu-backlight", 0); |
| 756 | plat->pch_backlight = fdtdec_get_int(blob, node, |
| 757 | "intel,pch-backlight", 0); |
| 758 | plat->pre_graphics_delay = fdtdec_get_int(blob, node, |
| 759 | "intel,pre-graphics-delay", 0); |
| 760 | priv->regs = (u8 *)dm_pci_read_bar32(dev, 0); |
| 761 | debug("%s: regs at %p\n", __func__, priv->regs); |
| 762 | debug("dp_hotplug %d %d %d\n", plat->dp_hotplug[0], plat->dp_hotplug[1], |
| 763 | plat->dp_hotplug[2]); |
| 764 | debug("port_select = %d\n", plat->port_select); |
| 765 | debug("power_up_delay = %d\n", plat->power_up_delay); |
| 766 | debug("power_backlight_on_delay = %d\n", |
| 767 | plat->power_backlight_on_delay); |
| 768 | debug("power_down_delay = %d\n", plat->power_down_delay); |
| 769 | debug("power_backlight_off_delay = %d\n", |
| 770 | plat->power_backlight_off_delay); |
| 771 | debug("power_cycle_delay = %d\n", plat->power_cycle_delay); |
| 772 | debug("cpu_backlight = %x\n", plat->cpu_backlight); |
| 773 | debug("pch_backlight = %x\n", plat->pch_backlight); |
| 774 | debug("cdclk = %d\n", plat->cdclk); |
| 775 | debug("pre_graphics_delay = %d\n", plat->pre_graphics_delay); |
| 776 | |
| 777 | return 0; |
| 778 | } |
| 779 | |
| 780 | static const struct video_ops broadwell_igd_ops = { |
| 781 | }; |
| 782 | |
| 783 | static const struct udevice_id broadwell_igd_ids[] = { |
| 784 | { .compatible = "intel,broadwell-igd" }, |
| 785 | { } |
| 786 | }; |
| 787 | |
| 788 | U_BOOT_DRIVER(broadwell_igd) = { |
| 789 | .name = "broadwell_igd", |
| 790 | .id = UCLASS_VIDEO, |
| 791 | .of_match = broadwell_igd_ids, |
| 792 | .ops = &broadwell_igd_ops, |
| 793 | .ofdata_to_platdata = broadwell_igd_ofdata_to_platdata, |
| 794 | .probe = broadwell_igd_probe, |
| 795 | .priv_auto_alloc_size = sizeof(struct broadwell_igd_priv), |
| 796 | .platdata_auto_alloc_size = sizeof(struct broadwell_igd_plat), |
| 797 | }; |