arch/arm/cpu/armv7/nonsec_virt.S

/*
 * code for switching cores into non-secure state
 *
 * Copyright (c) 2013	Andre Przywara <andre.przywara@linaro.org>
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

#include <config.h>
#include <linux/linkage.h>
#include <asm/gic.h>
#include <asm/armv7.h>

.arch_extension sec

/* the vector table for secure state */
_monitor_vectors:
	.word 0	/* reset */
	.word 0 /* undef */
	adr pc, _secure_monitor
	.word 0
	.word 0
	.word 0
	.word 0
	.word 0

/*
 * secure monitor handler
 * U-boot calls this "software interrupt" in start.S
 * This is executed on a "smc" instruction, we use a "smc #0" to switch
 * to non-secure state.
 * We use only r0 and r1 here, due to constraints in the caller.
 */
	.align	5
_secure_monitor:
	mrc	p15, 0, r1, c1, c1, 0		@ read SCR
	bic	r1, r1, #0x4e			@ clear IRQ, FIQ, EA, nET bits
	orr	r1, r1, #0x31			@ enable NS, AW, FW bits

	mcr	p15, 0, r1, c1, c1, 0		@ write SCR (with NS bit set)

	movs	pc, lr				@ return to non-secure SVC

/*
 * Switch a core to non-secure state.
 *
 *  1. initialize the GIC per-core interface
 *  2. allow coprocessor access in non-secure modes
 *  3. switch the cpu mode (by calling "smc #0")
 *
 * Called from smp_pen by secondary cores and directly by the BSP.
 * Do not assume that the stack is available and only use registers
 * r0-r3 and r12.
 *
 * PERIPHBASE is used to get the GIC address. This could be 40 bits long,
 * though, but we check this in C before calling this function.
 */
ENTRY(_nonsec_init)
#ifdef CONFIG_ARM_GIC_BASE_ADDRESS
	ldr	r2, =CONFIG_ARM_GIC_BASE_ADDRESS
#else
	mrc	p15, 4, r2, c15, c0, 0		@ read CBAR
	bfc	r2, #0, #15			@ clear reserved bits
#endif
	add	r3, r2, #GIC_DIST_OFFSET	@ GIC dist i/f offset
	mvn	r1, #0				@ all bits to 1
	str	r1, [r3, #GICD_IGROUPRn]	@ allow private interrupts

	mrc	p15, 0, r0, c0, c0, 0		@ read MIDR
	ldr	r1, =MIDR_PRIMARY_PART_MASK
	and	r0, r0, r1			@ mask out variant and revision

	ldr	r1, =MIDR_CORTEX_A7_R0P0 & MIDR_PRIMARY_PART_MASK
	cmp	r0, r1				@ check for Cortex-A7

	ldr	r1, =MIDR_CORTEX_A15_R0P0 & MIDR_PRIMARY_PART_MASK
	cmpne	r0, r1				@ check for Cortex-A15

	movne	r1, #GIC_CPU_OFFSET_A9		@ GIC CPU offset for A9
	moveq	r1, #GIC_CPU_OFFSET_A15		@ GIC CPU offset for A15/A7
	add	r3, r2, r1			@ r3 = GIC CPU i/f addr

	mov	r1, #1				@ set GICC_CTLR[enable]
	str	r1, [r3, #GICC_CTLR]		@ and clear all other bits
	mov	r1, #0xff
	str	r1, [r3, #GICC_PMR]		@ set priority mask register

	movw	r1, #0x3fff
	movt	r1, #0x0006
	mcr	p15, 0, r1, c1, c1, 2		@ NSACR = all copros to non-sec

/* The CNTFRQ register of the generic timer needs to be
 * programmed in secure state. Some primary bootloaders / firmware
 * omit this, so if the frequency is provided in the configuration,
 * we do this here instead.
 * But first check if we have the generic timer.
 */
#ifdef CONFIG_SYS_CLK_FREQ
	mrc	p15, 0, r0, c0, c1, 1		@ read ID_PFR1
	and	r0, r0, #CPUID_ARM_GENTIMER_MASK	@ mask arch timer bits
	cmp	r0, #(1 << CPUID_ARM_GENTIMER_SHIFT)
	ldreq	r1, =CONFIG_SYS_CLK_FREQ
	mcreq	p15, 0, r1, c14, c0, 0		@ write CNTFRQ
#endif

	adr	r1, _monitor_vectors
	mcr	p15, 0, r1, c12, c0, 1		@ set MVBAR to secure vectors

	mrc	p15, 0, ip, c12, c0, 0		@ save secure copy of VBAR

	isb
	smc	#0				@ call into MONITOR mode

	mcr	p15, 0, ip, c12, c0, 0		@ write non-secure copy of VBAR

	mov	r1, #1
	str	r1, [r3, #GICC_CTLR]		@ enable non-secure CPU i/f
	add	r2, r2, #GIC_DIST_OFFSET
	str	r1, [r2, #GICD_CTLR]		@ allow private interrupts

	mov	r0, r3				@ return GICC address

	bx	lr
ENDPROC(_nonsec_init)