board/prodrive/p3p440/p3p440.c

/*
 * (C) Copyright 2005
 * Stefan Roese, DENX Software Engineering, sr@denx.de.
 *
 * Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <asm/processor.h>
#include <command.h>

#include "p3p440.h"

DECLARE_GLOBAL_DATA_PTR;

void set_led(int color)
{
	switch (color) {
	case LED_OFF:
		out32(GPIO0_OR,  in32(GPIO0_OR) & ~CONFIG_SYS_LED_GREEN & ~CONFIG_SYS_LED_RED);
		break;

	case LED_GREEN:
		out32(GPIO0_OR,  (in32(GPIO0_OR) | CONFIG_SYS_LED_GREEN) & ~CONFIG_SYS_LED_RED);
		break;

	case LED_RED:
		out32(GPIO0_OR,  (in32(GPIO0_OR) | CONFIG_SYS_LED_RED) & ~CONFIG_SYS_LED_GREEN);
		break;

	case LED_ORANGE:
		out32(GPIO0_OR,  in32(GPIO0_OR) | CONFIG_SYS_LED_GREEN | CONFIG_SYS_LED_RED);
		break;
	}
}

static int is_monarch(void)
{
	out32(GPIO0_OR,  in32(GPIO0_OR) & ~CONFIG_SYS_GPIO_RDY);
	udelay(1000);

	if (in32(GPIO0_IR) & CONFIG_SYS_MONARCH_IO)
		return 0;
	else
		return 1;
}

static void wait_for_pci_ready(void)
{
	/*
	 * Configure EREADY_IO as input
	 */
	out32(GPIO0_TCR, in32(GPIO0_TCR) & ~CONFIG_SYS_EREADY_IO);
	udelay(1000);

	for (;;) {
		if (in32(GPIO0_IR) & CONFIG_SYS_EREADY_IO)
			return;
	}

}

int board_early_init_f(void)
{
	uint reg;

	/*--------------------------------------------------------------------
	 * Setup the external bus controller/chip selects
	 *-------------------------------------------------------------------*/
	mtdcr(EBC0_CFGADDR, EBC0_CFG);
	reg = mfdcr(EBC0_CFGDATA);
	mtdcr(EBC0_CFGDATA, reg | 0x04000000);	/* Set ATC */

	/*--------------------------------------------------------------------
	 * Setup pin multiplexing (GPIO/IRQ...)
	 *-------------------------------------------------------------------*/
	mtdcr(CPC0_GPIO, 0x03F01F80);

	out32(GPIO0_ODR, 0x00000000);	/* no open drain pins      */
	out32(GPIO0_TCR, CONFIG_SYS_GPIO_RDY | CONFIG_SYS_EREADY_IO | CONFIG_SYS_LED_RED | CONFIG_SYS_LED_GREEN);
	out32(GPIO0_OR,  CONFIG_SYS_GPIO_RDY);

	/*--------------------------------------------------------------------
	 * Setup the interrupt controller polarities, triggers, etc.
	 *-------------------------------------------------------------------*/
	mtdcr(UIC0SR, 0xffffffff);	/* clear all */
	mtdcr(UIC0ER, 0x00000000);	/* disable all */
	mtdcr(UIC0CR, 0x00000001);	/* UIC1 crit is critical */
	mtdcr(UIC0PR, 0xfffffe13);	/* per ref-board manual */
	mtdcr(UIC0TR, 0x01c00008);	/* per ref-board manual */
	mtdcr(UIC0VR, 0x00000001);	/* int31 highest, base=0x000 */
	mtdcr(UIC0SR, 0xffffffff);	/* clear all */

	mtdcr(UIC1SR, 0xffffffff);	/* clear all */
	mtdcr(UIC1ER, 0x00000000);	/* disable all */
	mtdcr(UIC1CR, 0x00000000);	/* all non-critical */
	mtdcr(UIC1PR, 0xffffe0ff);	/* per ref-board manual */
	mtdcr(UIC1TR, 0x00ffc000);	/* per ref-board manual */
	mtdcr(UIC1VR, 0x00000001);	/* int31 highest, base=0x000 */
	mtdcr(UIC1SR, 0xffffffff);	/* clear all */

	return 0;
}

int checkboard(void)
{
	char buf[64];
	int i = getenv_f("serial#", buf, sizeof(buf));

	printf("Board: P3P440");
	if (i > 0) {
		puts(", serial# ");
		puts(buf);
	}

	if (is_monarch()) {
		puts(", Monarch");
	} else {
		puts(", None-Monarch");
	}

	putc('\n');

	return (0);
}

int misc_init_r (void)
{
	/*
	 * Adjust flash start and offset to detected values
	 */
	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
	gd->bd->bi_flashoffset = 0;

	/*
	 * Check if only one FLASH bank is available
	 */
	if (gd->bd->bi_flashsize != CONFIG_SYS_MAX_FLASH_BANKS * (0 - CONFIG_SYS_FLASH0)) {
		mtebc(PB1CR, 0);			/* disable cs */
		mtebc(PB1AP, 0);
		mtebc(PB2CR, 0);			/* disable cs */
		mtebc(PB2AP, 0);
		mtebc(PB3CR, 0);			/* disable cs */
		mtebc(PB3AP, 0);
	}

	return 0;
}

/*************************************************************************
 * Override weak is_pci_host()
 *
 *	This routine is called to determine if a pci scan should be
 *	performed. With various hardware environments (especially cPCI and
 *	PPMC) it's insufficient to depend on the state of the arbiter enable
 *	bit in the strap register, or generic host/adapter assumptions.
 *
 *	Rather than hard-code a bad assumption in the general 440 code, the
 *	440 pci code requires the board to decide at runtime.
 *
 *	Return 0 for adapter mode, non-zero for host (monarch) mode.
 *
 *
 ************************************************************************/
#if defined(CONFIG_PCI)
int is_pci_host(struct pci_controller *hose)
{
	if (is_monarch()) {
		wait_for_pci_ready();
		return 1;		/* return 1 for host controller */
	} else {
		return 0;		/* return 0 for adapter controller */
	}
}
#endif				/* defined(CONFIG_PCI) */