board/pcs440ep/pcs440ep.c

/*
 * (C) Copyright 2006
 * Stefan Roese, DENX Software Engineering, sr@denx.de.
 *
 * SPDX-License-Identifier:	GPL-2.0+ 
 */

#include <common.h>
#include <asm/ppc4xx.h>
#include <malloc.h>
#include <command.h>
#include <crc.h>
#include <asm/processor.h>
#include <spd_sdram.h>
#include <status_led.h>
#include <sha1.h>
#include <asm/io.h>
#include <net.h>
#include <ata.h>

DECLARE_GLOBAL_DATA_PTR;

extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips	*/

unsigned char	sha1_checksum[SHA1_SUM_LEN];

/* swap 4 Bits (Bit0 = Bit3, Bit1 = Bit2, Bit2 = Bit1 and Bit3 = Bit0) */
unsigned char swapbits[16] = {0x0, 0x8, 0x4, 0xc, 0x2, 0xa, 0x6, 0xe,
			      0x1, 0x9, 0x5, 0xd, 0x3, 0xb, 0x7, 0xf};

static void set_leds (int val)
{
	out32(GPIO0_OR, (in32 (GPIO0_OR) & ~0x78000000) | (val << 27));
}

#define GET_LEDS ((in32 (GPIO0_OR) & 0x78000000) >> 27)

void __led_init (led_id_t mask, int state)
{
	int	val = GET_LEDS;

	if (state == STATUS_LED_ON)
		val |= mask;
	else
		val &= ~mask;
	set_leds (val);
}

void __led_set (led_id_t mask, int state)
{
	int	val = GET_LEDS;

	if (state == STATUS_LED_ON)
		val |= mask;
	else if (state == STATUS_LED_OFF)
		val &= ~mask;
	set_leds (val);
}

void __led_toggle (led_id_t mask)
{
	int	val = GET_LEDS;

	val ^= mask;
	set_leds (val);
}

static void status_led_blink (void)
{
	int	i;
	int	val = GET_LEDS;

	/* set all LED which are on, to state BLINKING */
	for (i = 0; i < 4; i++) {
		if (val & 0x01) status_led_set (3 - i, STATUS_LED_BLINKING);
		else status_led_set (3 - i, STATUS_LED_OFF);
		val = val >> 1;
	}
}

#if defined(CONFIG_SHOW_BOOT_PROGRESS)
void show_boot_progress (int val)
{
	/* find all valid Codes for val in README */
	if (val == -BOOTSTAGE_ID_NEED_RESET)
		return;
	if (val < 0) {
		/* smthing goes wrong */
		status_led_blink ();
		return;
	}
	switch (val) {
	case BOOTSTAGE_ID_CHECK_MAGIC:
		/* validating Image */
		status_led_set(0, STATUS_LED_OFF);
		status_led_set(1, STATUS_LED_ON);
		status_led_set(2, STATUS_LED_ON);
		break;
	case BOOTSTAGE_ID_RUN_OS:
		status_led_set(0, STATUS_LED_ON);
		status_led_set(1, STATUS_LED_ON);
		status_led_set(2, STATUS_LED_ON);
		break;
#if 0
	case BOOTSTAGE_ID_NET_ETH_START:
		/* starting Ethernet configuration */
		status_led_set(0, STATUS_LED_OFF);
		status_led_set(1, STATUS_LED_OFF);
		status_led_set(2, STATUS_LED_ON);
		break;
#endif
	case BOOTSTAGE_ID_NET_START:
		/* loading Image */
		status_led_set(0, STATUS_LED_ON);
		status_led_set(1, STATUS_LED_OFF);
		status_led_set(2, STATUS_LED_ON);
		break;
	}
}
#endif

int board_early_init_f(void)
{
	register uint reg;

	set_leds(0);			/* display boot info counter */

	/*--------------------------------------------------------------------
	 * Setup the external bus controller/chip selects
	 *-------------------------------------------------------------------*/
	mtdcr(EBC0_CFGADDR, EBC0_CFG);
	reg = mfdcr(EBC0_CFGDATA);
	mtdcr(EBC0_CFGDATA, reg | 0x04000000);	/* Set ATC */

	/*--------------------------------------------------------------------
	 * GPIO's are alreay setup in arch/powerpc/cpu/ppc4xx/cpu_init.c
	 * via define from board config file.
	 *-------------------------------------------------------------------*/

	/*--------------------------------------------------------------------
	 * Setup the interrupt controller polarities, triggers, etc.
	 *-------------------------------------------------------------------*/
	mtdcr(UIC0SR, 0xffffffff);	/* clear all */
	mtdcr(UIC0ER, 0x00000000);	/* disable all */
	mtdcr(UIC0CR, 0x00000001);	/* UIC1 crit is critical */
	mtdcr(UIC0PR, 0xfffffe1f);	/* per ref-board manual */
	mtdcr(UIC0TR, 0x01c00000);	/* per ref-board manual */
	mtdcr(UIC0VR, 0x00000001);	/* int31 highest, base=0x000 */
	mtdcr(UIC0SR, 0xffffffff);	/* clear all */

	mtdcr(UIC1SR, 0xffffffff);	/* clear all */
	mtdcr(UIC1ER, 0x00000000);	/* disable all */
	mtdcr(UIC1CR, 0x00000000);	/* all non-critical */
	mtdcr(UIC1PR, 0xffffe0ff);	/* per ref-board manual */
	mtdcr(UIC1TR, 0x00ffc000);	/* per ref-board manual */
	mtdcr(UIC1VR, 0x00000001);	/* int31 highest, base=0x000 */
	mtdcr(UIC1SR, 0xffffffff);	/* clear all */

	/*--------------------------------------------------------------------
	 * Setup other serial configuration
	 *-------------------------------------------------------------------*/
	mfsdr(SDR0_PCI0, reg);
	mtsdr(SDR0_PCI0, 0x80000000 | reg);	/* PCI arbiter enabled */
	mtsdr(SDR0_PFC0, 0x00000000);	/* Pin function: enable GPIO49-63 */
	mtsdr(SDR0_PFC1, 0x00048000);	/* Pin function: UART0 has 4 pins, select IRQ5 */

	return 0;
}

#define EEPROM_LEN	256
static void load_ethaddr(void)
{
	int	ok_ethaddr, ok_eth1addr;
	int	ret;
	uchar	buf[EEPROM_LEN];
	char	*use_eeprom;
	u16	checksumcrc16 = 0;

	/* If the env is sane, then nothing for us to do */
	ok_ethaddr = eth_getenv_enetaddr("ethaddr", buf);
	ok_eth1addr = eth_getenv_enetaddr("eth1addr", buf);
	if (ok_ethaddr && ok_eth1addr)
		return;

	/* read the MACs from EEprom */
	status_led_set (0, STATUS_LED_ON);
	status_led_set (1, STATUS_LED_ON);
	ret = eeprom_read (CONFIG_SYS_I2C_EEPROM_ADDR, 0, buf, EEPROM_LEN);
	if (ret == 0) {
		checksumcrc16 = cyg_crc16 (buf, EEPROM_LEN - 2);
		/* check, if the EEprom is programmed:
		 * - The Prefix(Byte 0,1,2) is equal to "ATR"
		 * - The checksum, stored in the last 2 Bytes, is correct
		 */
		if ((strncmp ((char *)buf,"ATR",3) != 0) ||
		    ((checksumcrc16 >> 8) != buf[EEPROM_LEN - 2]) ||
		    ((checksumcrc16 & 0xff) != buf[EEPROM_LEN - 1])) {
			/* EEprom is not programmed */
			printf("%s: EEPROM Checksum not OK\n", __FUNCTION__);
		} else {
			/* get the MACs */
			if (!ok_ethaddr)
				eth_setenv_enetaddr("ethaddr", &buf[3]);
			if (!ok_eth1addr)
				eth_setenv_enetaddr("eth1addr", &buf[9]);
			return;
		}
	}

	/* some error reading the EEprom */
	if ((use_eeprom = getenv ("use_eeprom_ethaddr")) == NULL) {
		/* dont use bootcmd */
		setenv("bootdelay", "-1");
		return;
	}
	/* == default ? use standard */
	if (strncmp (use_eeprom, "default", 7) == 0) {
		return;
	}
	/* Env doesnt exist -> hang */
	status_led_blink ();
	/* here we do this "handy" because we have no interrupts
	   at this time */
	puts ("### EEPROM ERROR ### Please RESET the board ###\n");
	for (;;) {
		__led_toggle (12);
		udelay (100000);
	}
	return;
}

#ifdef CONFIG_PREBOOT

static uchar kbd_magic_prefix[]		= "key_magic";
static uchar kbd_command_prefix[]	= "key_cmd";

struct kbd_data_t {
	char s1;
	char s2;
};

struct kbd_data_t* get_keys (struct kbd_data_t *kbd_data)
{
	char *val;
	unsigned long tmp;

	/* use the DIPs for some bootoptions */
	val = getenv (ENV_NAME_DIP);
	tmp = simple_strtoul (val, NULL, 16);

	kbd_data->s2 = (tmp & 0x0f);
	kbd_data->s1 = (tmp & 0xf0) >> 4;
	return kbd_data;
}

static int compare_magic (const struct kbd_data_t *kbd_data, char *str)
{
	char s1 = str[0];

	if (s1 >= '0' && s1 <= '9')
		s1 -= '0';
	else if (s1 >= 'a' && s1 <= 'f')
		s1 = s1 - 'a' + 10;
	else if (s1 >= 'A' && s1 <= 'F')
		s1 = s1 - 'A' + 10;
	else
		return -1;

	if (s1 != kbd_data->s1) return -1;

	s1 = str[1];
	if (s1 >= '0' && s1 <= '9')
		s1 -= '0';
	else if (s1 >= 'a' && s1 <= 'f')
		s1 = s1 - 'a' + 10;
	else if (s1 >= 'A' && s1 <= 'F')
		s1 = s1 - 'A' + 10;
	else
		return -1;

	if (s1 != kbd_data->s2) return -1;
	return 0;
}

static char *key_match (const struct kbd_data_t *kbd_data)
{
	char magic[sizeof (kbd_magic_prefix) + 1];
	char *suffix;
	char *kbd_magic_keys;

	/*
	 * The following string defines the characters that can be appended
	 * to "key_magic" to form the names of environment variables that
	 * hold "magic" key codes, i. e. such key codes that can cause
	 * pre-boot actions. If the string is empty (""), then only
	 * "key_magic" is checked (old behaviour); the string "125" causes
	 * checks for "key_magic1", "key_magic2" and "key_magic5", etc.
	 */
	if ((kbd_magic_keys = getenv ("magic_keys")) == NULL)
		kbd_magic_keys = "";

	/* loop over all magic keys;
	 * use '\0' suffix in case of empty string
	 */
	for (suffix = kbd_magic_keys; *suffix ||
		     suffix == kbd_magic_keys; ++suffix) {
		sprintf (magic, "%s%c", kbd_magic_prefix, *suffix);
		if (compare_magic (kbd_data, getenv (magic)) == 0) {
			char cmd_name[sizeof (kbd_command_prefix) + 1];
			char *cmd;

			sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix);
			cmd = getenv (cmd_name);

			return (cmd);
		}
	}
	return (NULL);
}

#endif /* CONFIG_PREBOOT */

static int pcs440ep_readinputs (void)
{
	int	i;
	char	value[20];

	/* read the inputs and set the Envvars */
	/* Revision Level Bit 26 - 29 */
	i = ((in32 (GPIO0_IR) & 0x0000003c) >> 2);
	i = swapbits[i];
	sprintf (value, "%02x", i);
	setenv (ENV_NAME_REVLEV, value);
	/* Solder Switch Bit 30 - 33 */
	i = (in32 (GPIO0_IR) & 0x00000003) << 2;
	i += (in32 (GPIO1_IR) & 0xc0000000) >> 30;
	i = swapbits[i];
	sprintf (value, "%02x", i);
	setenv (ENV_NAME_SOLDER, value);
	/* DIP Switch Bit 49 - 56 */
	i = ((in32 (GPIO1_IR) & 0x00007f80) >> 7);
	i = (swapbits[i & 0x0f] << 4) + swapbits[(i & 0xf0) >> 4];
	sprintf (value, "%02x", i);
	setenv (ENV_NAME_DIP, value);
	return 0;
}


#if defined(CONFIG_SHA1_CHECK_UB_IMG)
/*************************************************************************
 * calculate a SHA1 sum for the U-Boot image in Flash.
 *
 ************************************************************************/
static int pcs440ep_sha1 (int docheck)
{
	unsigned char *data;
	unsigned char *ptroff;
	unsigned char output[20];
	unsigned char org[20];
	int	i, len = CONFIG_SHA1_LEN;

	memcpy ((char *)CONFIG_SYS_LOAD_ADDR, (char *)CONFIG_SHA1_START, len);
	data = (unsigned char *)CONFIG_SYS_LOAD_ADDR;
	ptroff = &data[len + SHA1_SUM_POS];

	for (i = 0; i < SHA1_SUM_LEN; i++) {
		org[i] = ptroff[i];
		ptroff[i] = 0;
	}

	sha1_csum ((unsigned char *) data, len, (unsigned char *)output);

	if (docheck == 2) {
		for (i = 0; i < 20 ; i++) {
			printf("%02X ", output[i]);
		}
		printf("\n");
	}
	if (docheck == 1) {
		for (i = 0; i < 20 ; i++) {
			if (org[i] != output[i]) return 1;
		}
	}
	return 0;
}

/*************************************************************************
 * do some checks after the SHA1 checksum from the U-Boot Image was
 * calculated.
 *
 ************************************************************************/
static void pcs440ep_checksha1 (void)
{
	int	ret;
	char	*cs_test;

	status_led_set (0, STATUS_LED_OFF);
	status_led_set (1, STATUS_LED_OFF);
	status_led_set (2, STATUS_LED_ON);
	ret = pcs440ep_sha1 (1);
	if (ret == 0) return;

	if ((cs_test = getenv ("cs_test")) == NULL) {
		/* Env doesnt exist -> hang */
		status_led_blink ();
		/* here we do this "handy" because we have no interrupts
		   at this time */
		puts ("### SHA1 ERROR ### Please RESET the board ###\n");
		for (;;) {
			__led_toggle (2);
			udelay (100000);
		}
	}

	if (strncmp (cs_test, "off", 3) == 0) {
		printf ("SHA1 U-Boot sum NOT ok!\n");
		setenv ("bootdelay", "-1");
	}
}
#else
static __inline__ void pcs440ep_checksha1 (void) { do {} while (0);}
#endif

int misc_init_r (void)
{
	uint pbcr;
	int size_val = 0;

	load_ethaddr();

	/* Re-do sizing to get full correct info */
	mtdcr(EBC0_CFGADDR, PB0CR);
	pbcr = mfdcr(EBC0_CFGDATA);
	switch (gd->bd->bi_flashsize) {
	case 1 << 20:
		size_val = 0;
		break;
	case 2 << 20:
		size_val = 1;
		break;
	case 4 << 20:
		size_val = 2;
		break;
	case 8 << 20:
		size_val = 3;
		break;
	case 16 << 20:
		size_val = 4;
		break;
	case 32 << 20:
		size_val = 5;
		break;
	case 64 << 20:
		size_val = 6;
		break;
	case 128 << 20:
		size_val = 7;
		break;
	}
	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
	mtdcr(EBC0_CFGADDR, PB0CR);
	mtdcr(EBC0_CFGDATA, pbcr);

	/* adjust flash start and offset */
	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
	gd->bd->bi_flashoffset = 0;

	/* Monitor protection ON by default */
	(void)flash_protect(FLAG_PROTECT_SET,
			    -CONFIG_SYS_MONITOR_LEN,
			    0xffffffff,
			    &flash_info[1]);

	/* Env protection ON by default */
	(void)flash_protect(FLAG_PROTECT_SET,
			    CONFIG_ENV_ADDR_REDUND,
			    CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1,
			    &flash_info[1]);

	pcs440ep_readinputs ();
	pcs440ep_checksha1 ();
#ifdef CONFIG_PREBOOT
	{
		struct kbd_data_t kbd_data;
		/* Decode keys */
		char *str = strdup (key_match (get_keys (&kbd_data)));
		/* Set or delete definition */
		setenv ("preboot", str);
		free (str);
	}
#endif /* CONFIG_PREBOOT */
	return 0;
}

int checkboard(void)
{
	char buf[64];
	int i = getenv_f("serial#", buf, sizeof(buf));

	printf("Board: PCS440EP");
	if (i > 0) {
		puts(", serial# ");
		puts(buf);
	}
	putc('\n');

	return (0);
}

void spd_ddr_init_hang (void)
{
	status_led_set (0, STATUS_LED_OFF);
	status_led_set (1, STATUS_LED_ON);
	/* we cannot use hang() because we are still running from
	   Flash, and so the status_led driver is not initialized */
	puts ("### SDRAM ERROR ### Please RESET the board ###\n");
	for (;;) {
		__led_toggle (4);
		udelay (100000);
	}
}

phys_size_t initdram (int board_type)
{
	long dram_size = 0;

	status_led_set (0, STATUS_LED_ON);
	status_led_set (1, STATUS_LED_OFF);
	dram_size = spd_sdram();
	status_led_set (0, STATUS_LED_OFF);
	status_led_set (1, STATUS_LED_ON);
	if (dram_size == 0) {
		hang();
	}

	return dram_size;
}

/*************************************************************************
 *  hw_watchdog_reset
 *
 *	This routine is called to reset (keep alive) the watchdog timer
 *
 ************************************************************************/
#if defined(CONFIG_HW_WATCHDOG)
void hw_watchdog_reset(void)
{

}
#endif

/*************************************************************************
 * "led" Commando for the U-Boot shell
 *
 ************************************************************************/
int do_led (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
	int	rcode = 0, i;
	ulong	pattern = 0;

	pattern = simple_strtoul (argv[1], NULL, 16);
	if (pattern > 0x400) {
		int	val = GET_LEDS;
		printf ("led: %x\n", val);
		return rcode;
	}
	if (pattern > 0x200) {
		status_led_blink ();
		hang ();
		return rcode;
	}
	if (pattern > 0x100) {
		status_led_blink ();
		return rcode;
	}
	pattern &= 0x0f;
	for (i = 0; i < 4; i++) {
		if (pattern & 0x01) status_led_set (i, STATUS_LED_ON);
		else status_led_set (i, STATUS_LED_OFF);
		pattern = pattern >> 1;
	}
	return rcode;
}

U_BOOT_CMD(
	led,	2,	1,	do_led,
	"set the DIAG-LED",
	"[bitmask] 0x01 = DIAG 1 on\n"
	"              0x02 = DIAG 2 on\n"
	"              0x04 = DIAG 3 on\n"
	"              0x08 = DIAG 4 on\n"
	"              > 0x100 set the LED, who are on, to state blinking"
);

#if defined(CONFIG_SHA1_CHECK_UB_IMG)
/*************************************************************************
 * "sha1" Commando for the U-Boot shell
 *
 ************************************************************************/
int do_sha1 (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
	int	rcode = -1;

	if (argc < 2) {
usage:
		return cmd_usage(cmdtp);
	}

	if (argc >= 3) {
		unsigned char *data;
		unsigned char output[20];
		int	len;
		int	i;

		data = (unsigned char *)simple_strtoul (argv[1], NULL, 16);
		len = simple_strtoul (argv[2], NULL, 16);
		sha1_csum (data, len, (unsigned char *)output);
		printf ("U-Boot sum:\n");
		for (i = 0; i < 20 ; i++) {
			printf ("%02X ", output[i]);
		}
		printf ("\n");
		if (argc == 4) {
			data = (unsigned char *)simple_strtoul (argv[3], NULL, 16);
			memcpy (data, output, 20);
		}
		return 0;
	}
	if (argc == 2) {
		char *ptr = argv[1];
		if (*ptr != '-') goto usage;
		ptr++;
		if ((*ptr == 'c') || (*ptr == 'C')) {
			rcode = pcs440ep_sha1 (1);
			printf ("SHA1 U-Boot sum %sok!\n", (rcode != 0) ? "not " : "");
		} else if ((*ptr == 'p') || (*ptr == 'P')) {
			rcode = pcs440ep_sha1 (2);
		} else {
			rcode = pcs440ep_sha1 (0);
		}
		return rcode;
	}
	return rcode;
}

U_BOOT_CMD(
	sha1,	4,	1,	do_sha1,
	"calculate the SHA1 Sum",
	"address len [addr]  calculate the SHA1 sum [save at addr]\n"
	"     -p calculate the SHA1 sum from the U-Boot image in flash and print\n"
	"     -c check the U-Boot image in flash"
);
#endif

#if defined (CONFIG_CMD_IDE)
/* These addresses need to be shifted one place to the left
 * ( bus per_addr 20 -30 is connectsd on CF bus A10-A0)
 * These values are shifted
 */
void inline ide_outb(int dev, int port, unsigned char val)
{
	debug ("ide_outb (dev= %d, port= 0x%x, val= 0x%02x) : @ 0x%08lx\n",
		dev, port, val, (ATA_CURR_BASE(dev)+port));

	out_be16((u16 *)(ATA_CURR_BASE(dev)+(port << 1)), val);
}
unsigned char inline ide_inb(int dev, int port)
{
	uchar val;
	val = in_be16((u16 *)(ATA_CURR_BASE(dev)+(port << 1)));
	debug ("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n",
		dev, port, (ATA_CURR_BASE(dev)+port), val);
	return (val);
}
#endif

#ifdef CONFIG_IDE_PREINIT
int ide_preinit (void)
{
	/* Set True IDE Mode */
	out32 (GPIO0_OR, (in32 (GPIO0_OR) | 0x00100000));
	out32 (GPIO0_OR, (in32 (GPIO0_OR) | 0x00200000));
	out32 (GPIO1_OR, (in32 (GPIO1_OR) & ~0x00008040));
	udelay (100000);
	return 0;
}
#endif

#if defined (CONFIG_CMD_IDE) && defined (CONFIG_IDE_RESET)
void ide_set_reset (int idereset)
{
	debug ("ide_reset(%d)\n", idereset);
	if (idereset == 0) {
		out32 (GPIO0_OR, (in32 (GPIO0_OR) | 0x00200000));
	} else {
		out32 (GPIO0_OR, (in32 (GPIO0_OR) & ~0x00200000));
	}
	udelay (10000);
}
#endif /* defined (CONFIG_CMD_IDE) && defined (CONFIG_IDE_RESET) */


/* this is motly the same as it should, causing a little code duplication */
#if defined(CONFIG_CMD_IDE)
#define EIEIO		__asm__ volatile ("eieio")

void ide_input_swap_data(int dev, ulong *sect_buf, int words)
{
	volatile ushort *pbuf =
		(ushort *) (ATA_CURR_BASE(dev) + ATA_DATA_REG);
	ushort *dbuf = (ushort *) sect_buf;

	debug("in input swap data base for read is %lx\n",
		(unsigned long) pbuf);

	while (words--) {
		*dbuf++ = *pbuf;
		*dbuf++ = *pbuf;
	}
}

void ide_output_data(int dev, const ulong *sect_buf, int words)
{
	ushort *dbuf;
	volatile ushort *pbuf;

	pbuf = (ushort *) (ATA_CURR_BASE(dev) + ATA_DATA_REG);
	dbuf = (ushort *) sect_buf;
	while (words--) {
		EIEIO;
		*pbuf = ld_le16(dbuf++);
		EIEIO;
		*pbuf = ld_le16(dbuf++);
	}
}

void ide_input_data(int dev, ulong *sect_buf, int words)
{
	ushort *dbuf;
	volatile ushort *pbuf;

	pbuf = (ushort *) (ATA_CURR_BASE(dev) + ATA_DATA_REG);
	dbuf = (ushort *) sect_buf;

	debug("in input data base for read is %lx\n", (unsigned long) pbuf);

	while (words--) {
		EIEIO;
		*dbuf++ = ld_le16(pbuf);
		EIEIO;
		*dbuf++ = ld_le16(pbuf);
	}
}

#endif