| Wolfgang Denk | 0ee7077 | 2005-09-23 11:05:55 +0200 | [diff] [blame] | 1 | AMCC Ocotea Board |
| wdenk | acd9b10 | 2004-03-14 00:59:59 +0000 | [diff] [blame] | 2 | |
| 3 | Last Update: March 2, 2004 |
| 4 | ======================================================================= |
| 5 | |
| Wolfgang Denk | 0ee7077 | 2005-09-23 11:05:55 +0200 | [diff] [blame] | 6 | This file contains some handy info regarding U-Boot and the AMCC |
| wdenk | acd9b10 | 2004-03-14 00:59:59 +0000 | [diff] [blame] | 7 | Ocotea 440gx evalutation board. See the README.ppc440 for additional |
| 8 | information. |
| 9 | |
| 10 | |
| 11 | SWITCH SETTINGS & JUMPERS |
| 12 | ========================== |
| 13 | |
| 14 | Here's what I've been using successfully. If you feel inclined to |
| 15 | change things ... please read the docs! |
| 16 | |
| 17 | DIPSW U46 U80 |
| 18 | ------------------------ |
| 19 | SW 1 off off |
| 20 | SW 2 on off |
| 21 | SW 3 off off |
| 22 | SW 4 off off |
| 23 | SW 5 off off |
| 24 | SW 6 on on |
| 25 | SW 7 on off |
| 26 | SW 8 on off |
| 27 | |
| 28 | J41: strapped |
| 29 | J42: open |
| 30 | |
| 31 | All others are factory default. |
| 32 | |
| 33 | |
| 34 | I2C Information |
| 35 | ===================== |
| 36 | |
| 37 | See README.ebony for information. |
| 38 | |
| 39 | PCI |
| 40 | =========================== |
| 41 | |
| 42 | Untested at the time of writing. |
| 43 | |
| 44 | PPC440GX Ethernet EMACs |
| 45 | =========================== |
| 46 | |
| 47 | All EMAC ports have been tested and are known to work |
| 48 | with EPS Group 4. |
| 49 | |
| 50 | Special note about the Cicada CIS8201: |
| 51 | The CIS8201 Gigabit PHY comes up in GMII mode by default. |
| 52 | One must hit an extended register to allow use of RGMII mode. |
| 53 | This has been done in the 440gx_enet.c file with a #ifdef/endif |
| 54 | pair. |
| 55 | |
| Wolfgang Denk | 0ee7077 | 2005-09-23 11:05:55 +0200 | [diff] [blame] | 56 | AMCC does not store the EMAC ethernet addresses within their PIBS bootloader. |
| wdenk | acd9b10 | 2004-03-14 00:59:59 +0000 | [diff] [blame] | 57 | The addresses contained in the config header file are from my particular |
| 58 | board and you _*should*_ change them to reflect your board either in the |
| 59 | config file and/or in your environment variables. I found the addresses on |
| 60 | labels on the bottom side of the board. |
| 61 | |
| 62 | |
| 63 | BDI2k or JTAG Debugging |
| 64 | =========================== |
| 65 | |
| 66 | For ease of debugging you can swap the small boot flash and external SRAM |
| 67 | by changing U46:3 to on. You can then use the sram as your boot flash by |
| 68 | loading the sram via the jtag debugger. |
| 69 | |
| 70 | |
| 71 | Regards, |
| 72 | --Travis |
| 73 | <tsawyer@sandburst.com> |