Gitiles
Code Review Sign In
git01.mediatek.com / filogic / uboot / 93743d241c64bc1f7ecbf3262d1683176551e11f / . / src / arm / nxp / imx / imx6ull-dhcom-som.dtsi
blob: 830b5a5064f28b45e7f387fbe2d506540bedafa8 [file] [log] [blame]
Tom Rini53633a82024-02-29 12:33:36 -0500[diff] [blame]1// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
2/*
3 * Copyright (C) 2023 DH electronics GmbH
4 */
5
6#include "imx6ull-dhcor-som.dtsi"
7
8/ {
9 aliases {
10 /delete-property/ spi2;
11 /delete-property/ spi3;
12 i2c0 = &i2c2;
13 i2c1 = &i2c1;
14 mmc2 = &usdhc2;
15 rtc0 = &rtc_i2c;
16 rtc1 = &snvs_rtc;
17 serial0 = &uart1;
18 serial1 = &uart6; /* DHCOM UART2, special hardware required */
19 serial2 = &uart3;
20 serial3 = &uart2; /* Use BT UART always as ttymxc3 */
21 serial4 = &uart4;
22 serial5 = &uart5;
23 spi0 = &ecspi1;
24 spi1 = &ecspi4; /* DHCOM SPI2, special hardware required */
25 };
26
27 chosen {
28 stdout-path = "serial0:115200n8";
29 };
30
31 reg_ext_3v3_ref: regulator-ext-3v3-ref {
32 compatible = "regulator-fixed";
33 regulator-always-on;
34 regulator-max-microvolt = <3300000>;
35 regulator-min-microvolt = <3300000>;
36 regulator-name = "VCC_3V3_REF";
37 };
38
39 reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
40 compatible = "regulator-fixed";
41 regulator-max-microvolt = <5000000>;
42 regulator-min-microvolt = <5000000>;
43 regulator-name = "usb-otg1-vbus";
44 };
45
46 reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
47 compatible = "regulator-fixed";
48 gpio = <&gpio1 5 GPIO_ACTIVE_LOW>;
49 regulator-max-microvolt = <5000000>;
50 regulator-min-microvolt = <5000000>;
51 regulator-name = "usb-otg2-vbus";
52 };
53
54 /* SoM with WiFi/BT: WiFi pin WL_REG_ON is connected to a DHCOM GPIO */
55 /omit-if-no-ref/ usdhc1_pwrseq: usdhc1-pwrseq {
56 compatible = "mmc-pwrseq-simple";
57 reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; /* GPIO H */
58 };
59};
60
61/* SoM with WiFi/BT: BT pin BT_REG_ON is connected to a DHCOM GPIO */
62&bluetooth {
63 shutdown-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
64};
65
66&can1 {
67 pinctrl-0 = <&pinctrl_flexcan1>;
68 pinctrl-names = "default";
69 status = "okay";
70};
71
72/*
73 * The signals for CAN2 TX and RX are routed to the DHCOM UART1 RTS/CTS pins.
74 * Only if this pins are used as CAN interface enable it on board layer.
75 */
76&can2 {
77 pinctrl-0 = <&pinctrl_flexcan2>;
78 pinctrl-names = "default";
79};
80
81/* DHCOM SPI1 */
82&ecspi1 {
83 cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
84 pinctrl-0 = <&pinctrl_ecspi1>;
85 pinctrl-names = "default";
86 status = "okay";
87};
88
89/*
90 * DHCOM SPI2
91 * Special hardware required that uses the pins of FEC2. Therefore this SPI
92 * interface can only be used if FEC2 is disabled.
93 */
94&ecspi4 {
95 cs-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
96 pinctrl-0 = <&pinctrl_ecspi4>;
97 pinctrl-names = "default";
98};
99
100/* DHCOM ETH1 */
101&fec1 {
102 phy-handle = <&mdio2_phy0>;
103 phy-mode = "rmii";
104 pinctrl-0 = <&pinctrl_fec1>;
105 pinctrl-names = "default";
106 status = "okay";
107};
108
109/* DHCOM ETH2 */
110&fec2 {
111 phy-handle = <&mdio2_phy1>;
112 phy-mode = "rmii";
113 pinctrl-0 = <&pinctrl_fec2>;
114 pinctrl-names = "default";
115 status = "okay";
116
117 mdio {
118 #address-cells = <1>;
119 #size-cells = <0>;
120
121 mdio2_phy0: ethernet-phy@0 {
122 compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
123 "ethernet-phy-ieee802.3-c22";
124 reg = <0>;
125 clock-names = "rmii-ref";
126 clocks = <&clks IMX6UL_CLK_ENET_REF>;
127 interrupt-parent = <&gpio5>;
128 interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
129 pinctrl-0 = <&pinctrl_fec1_phy &pinctrl_snvs_fec1_phy>;
130 pinctrl-names = "default";
131 reset-assert-us = <500>;
132 reset-deassert-us = <500>;
133 reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
134 smsc,disable-energy-detect; /* Make plugin detection reliable */
135 };
136
137 mdio2_phy1: ethernet-phy@1 {
138 compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
139 "ethernet-phy-ieee802.3-c22";
140 reg = <1>;
141 clock-names = "rmii-ref";
142 clocks = <&clks IMX6UL_CLK_ENET2_REF>;
143 interrupt-parent = <&gpio5>;
144 interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
145 pinctrl-0 = <&pinctrl_fec2_phy &pinctrl_snvs_fec2_phy>;
146 pinctrl-names = "default";
147 reset-assert-us = <500>;
148 reset-deassert-us = <500>;
149 reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
150 smsc,disable-energy-detect; /* Make plugin detection reliable */
151 };
152 };
153};
154
155&gpio1 {
156 gpio-line-names =
157 "", "", "", "",
158 "", "", "", "",
159 "", "", "", "DHCOM-INT",
160 "", "", "", "",
161 "", "", "DHCOM-I", "",
162 "", "", "", "",
163 "", "", "", "",
164 "", "", "", "";
165 pinctrl-0 = <&pinctrl_spi1_switch
166 &pinctrl_dhcom_i &pinctrl_dhcom_int>;
167 pinctrl-names = "default";
168};
169
170&gpio4 {
171 gpio-line-names =
172 "", "", "", "",
173 "", "", "", "",
174 "", "", "", "",
175 "", "", "", "",
176 "", "DHCOM-L", "DHCOM-K", "DHCOM-M",
177 "DHCOM-J", "DHCOM-U", "DHCOM-T", "DHCOM-S",
178 "DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
179 "DHCOM-N", "", "", "";
180 pinctrl-0 = <&pinctrl_dhcom_j &pinctrl_dhcom_k
181 &pinctrl_dhcom_l &pinctrl_dhcom_m
182 &pinctrl_dhcom_n &pinctrl_dhcom_o
183 &pinctrl_dhcom_p &pinctrl_dhcom_q
184 &pinctrl_dhcom_r &pinctrl_dhcom_s
185 &pinctrl_dhcom_t &pinctrl_dhcom_u>;
186 pinctrl-names = "default";
187};
188
189&gpio5 {
190 gpio-line-names =
191 "DHCOM-A", "DHCOM-B", "DHCOM-C", "DHCOM-D",
192 "DHCOM-E", "", "", "DHCOM-F",
193 "DHCOM-G", "DHCOM-H", "", "",
194 "", "", "", "",
195 "", "", "", "",
196 "", "", "", "",
197 "", "", "", "",
198 "", "", "", "";
199 pinctrl-0 = <&pinctrl_snvs_dhcom_a &pinctrl_snvs_dhcom_b
200 &pinctrl_snvs_dhcom_c &pinctrl_snvs_dhcom_d
201 &pinctrl_snvs_dhcom_e &pinctrl_snvs_dhcom_f
202 &pinctrl_snvs_dhcom_g &pinctrl_snvs_dhcom_h>;
203 pinctrl-names = "default";
204};
205
206/* DHCOM I2C2 */
207&i2c1 {
208 rtc_i2c: rtc@32 {
209 compatible = "microcrystal,rv8803";
210 reg = <0x32>;
211 };
212
213 /* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH1 */
214 eeprom@50 {
215 compatible = "atmel,24c02";
216 reg = <0x50>;
217 pagesize = <16>;
218 };
219
220 /* TI ADC101C027 */
221 adc@51 {
222 compatible = "ti,adc101c";
223 reg = <0x51>;
224 vref-supply = <&reg_ext_3v3_ref>;
225 };
226
227 /* TI ADC101C027 */
228 adc@52 {
229 compatible = "ti,adc101c";
230 reg = <0x52>;
231 vref-supply = <&reg_ext_3v3_ref>;
232 };
233
234 /* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH2 */
235 eeprom@53 {
236 compatible = "atmel,24c02";
237 reg = <0x53>;
238 pagesize = <16>;
239 };
240};
241
242/* DHCOM I2C1 */
243&i2c2 {
244 clock-frequency = <100000>;
245 pinctrl-0 = <&pinctrl_i2c2>;
246 pinctrl-1 = <&pinctrl_i2c2_gpio>;
247 pinctrl-names = "default", "gpio";
248 scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
249 sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
250 status = "okay";
251};
252
253&lcdif {
254 pinctrl-0 = <&pinctrl_lcdif>;
255 pinctrl-names = "default";
256};
257
258&pwm1 {
259 pinctrl-0 = <&pinctrl_pwm1>;
260 pinctrl-names = "default";
261};
262
263&sai2 {
264 assigned-clock-rates = <320000000>;
265 assigned-clocks = <&clks IMX6UL_CLK_PLL3_PFD2>;
266 pinctrl-0 = <&pinctrl_sai2>;
267 pinctrl-names = "default";
268};
269
270&tsc {
271 measure-delay-time = <0xffff>;
272 pinctrl-0 = <&pinctrl_tsc>;
273 pinctrl-names = "default";
274 pre-charge-time = <0xfff>;
275 touchscreen-average-samples = <32>;
276 xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
277};
278
279/* DHCOM UART1 */
280&uart1 {
281 pinctrl-0 = <&pinctrl_uart1>;
282 pinctrl-names = "default";
283 status = "okay";
284};
285
286/*
287 * DHCOM UART2 (alternative)
288 * Special hardware required that uses DHCOM GPIO pins for DHCOM UART2.
289 * Therefore this UART interface can only be used if DHCOM GPIOs J/K/L/M are
290 * removed from GPIO hog muxing.
291 */
292&uart6 {
293 pinctrl-0 = <&pinctrl_uart6>;
294 pinctrl-names = "default";
295 uart-has-rtscts;
296};
297
298&usbotg1 {
299 adp-disable;
300 disable-over-current;
301 dr_mode = "otg";
302 hnp-disable;
303 pinctrl-0 = <&pinctrl_usbotg1>;
304 pinctrl-names = "default";
305 srp-disable;
306 vbus-supply = <&reg_usb_otg1_vbus>;
307 status = "okay";
308};
309
310&usbotg2 {
311 disable-over-current; /* Overcurrent pin is used for TSC */
312 dr_mode = "host";
313 pinctrl-0 = <&pinctrl_usbotg2>;
314 pinctrl-names = "default";
315 tpl-support;
316 vbus-supply = <&reg_usb_otg2_vbus>;
317 status = "okay";
318};
319
320&usbphy1 {
321 fsl,tx-d-cal = <106>;
322};
323
324&usbphy2 {
325 fsl,tx-d-cal = <106>;
326};
327
328/* WiFi on LGA */
329&usdhc1 {
330 mmc-pwrseq = <&usdhc1_pwrseq>;
331};
332
333/* eMMC on module */
334&usdhc2 {
335 bus-width = <8>;
336 no-1-8-v;
337 non-removable;
338 pinctrl-0 = <&pinctrl_usdhc2>;
339 pinctrl-names = "default";
340 vmmc-supply = <&vcc_3v3>;
341 vqmmc-supply = <&vcc_3v3>;
342 status = "okay";
343};
344
345&iomuxc {
346 /* DHCOM GPIOs I..U + INT_HIGHEST_PRIORITY */
347 pinctrl_dhcom_i: dhcom-i-grp {
348 fsl,pins = <MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x400120b0>;
349 };
350
351 pinctrl_dhcom_j: dhcom-j-grp {
352 fsl,pins = <MX6UL_PAD_CSI_HSYNC__GPIO4_IO20 0x400120b0>;
353 };
354
355 pinctrl_dhcom_k: dhcom-k-grp {
356 fsl,pins = <MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18 0x400120b0>;
357 };
358
359 pinctrl_dhcom_l: dhcom-l-grp {
360 fsl,pins = <MX6UL_PAD_CSI_MCLK__GPIO4_IO17 0x400120b0>;
361 };
362
363 pinctrl_dhcom_m: dhcom-m-grp {
364 fsl,pins = <MX6UL_PAD_CSI_VSYNC__GPIO4_IO19 0x400120b0>;
365 };
366
367 pinctrl_dhcom_n: dhcom-n-grp {
368 fsl,pins = <MX6UL_PAD_CSI_DATA07__GPIO4_IO28 0x400120b0>;
369 };
370
371 pinctrl_dhcom_o: dhcom-o-grp {
372 fsl,pins = <MX6UL_PAD_CSI_DATA06__GPIO4_IO27 0x400120b0>;
373 };
374
375 pinctrl_dhcom_p: dhcom-p-grp {
376 fsl,pins = <MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x400120b0>;
377 };
378
379 pinctrl_dhcom_q: dhcom-q-grp {
380 fsl,pins = <MX6UL_PAD_CSI_DATA04__GPIO4_IO25 0x400120b0>;
381 };
382
383 pinctrl_dhcom_r: dhcom-r-grp {
384 fsl,pins = <MX6UL_PAD_CSI_DATA03__GPIO4_IO24 0x400120b0>;
385 };
386
387 pinctrl_dhcom_s: dhcom-s-grp {
388 fsl,pins = <MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x400120b0>;
389 };
390
391 pinctrl_dhcom_t: dhcom-t-grp {
392 fsl,pins = <MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x400120b0>;
393 };
394
395 pinctrl_dhcom_u: dhcom-u-grp {
396 fsl,pins = <MX6UL_PAD_CSI_DATA00__GPIO4_IO21 0x400120b0>;
397 };
398
399 pinctrl_dhcom_int: dhcom-int-grp {
400 fsl,pins = <MX6UL_PAD_JTAG_TMS__GPIO1_IO11 0x400120b0>;
401 };
402
403 pinctrl_ecspi1: ecspi1-grp {
404 fsl,pins = <
405 MX6UL_PAD_LCD_DATA23__ECSPI1_MISO 0x100b1
406 MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI 0x100b1
407 MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK 0x100b1
408 MX6UL_PAD_LCD_DATA21__GPIO3_IO26 0x1b0b0 /* SS0 */
409 >;
410 };
411
412 pinctrl_ecspi4: ecspi4-grp {
413 fsl,pins = <
414 MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO 0x100b1
415 MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI 0x100b1
416 MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK 0x100b1
417 MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x1b0b0 /* SS0 */
418 >;
419 };
420
421 pinctrl_fec1: fec1-grp {
422 fsl,pins = <
423 /* FEC1 uses MDIO bus from FEC2 */
424 MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
425 MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
426 MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
427 MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
428 MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b010
429 MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b010
430 MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b010
431 MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b010
432 >;
433 };
434
435 pinctrl_fec1_phy: fec1-phy-grp {
436 fsl,pins = <
437 MX6UL_PAD_LCD_DATA18__GPIO3_IO23 0xb0 /* SMSC PHY reset */
438 >;
439 };
440
441 pinctrl_fec2: fec2-grp {
442 fsl,pins = <
443 MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
444 MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
445 MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
446 MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
447 MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
448 MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
449 MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b010
450 MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b010
451 MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b010
452 MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b010
453 >;
454 };
455
456 pinctrl_fec2_phy: fec2-phy-grp {
457 fsl,pins = <
458 MX6UL_PAD_LCD_DATA19__GPIO3_IO24 0xb0 /* SMSC PHY reset */
459 >;
460 };
461
462 pinctrl_flexcan1: flexcan1-grp {
463 fsl,pins = <
464 MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020
465 MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020
466 >;
467 };
468
469 pinctrl_flexcan2: flexcan2-grp {
470 fsl,pins = <
471 MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
472 MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
473 >;
474 };
475
476 pinctrl_i2c2: i2c2-grp {
477 fsl,pins = <
478 MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
479 MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
480 >;
481 };
482
483 pinctrl_i2c2_gpio: i2c2-gpio-grp {
484 fsl,pins = <
485 MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001b8b0
486 MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001b8b0
487 >;
488 };
489
490 pinctrl_lcdif: lcdif-grp {
491 fsl,pins = <
492 MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
493 MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
494 MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
495 MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
496 MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
497 MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
498 MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
499 MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
500 MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
501 MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
502 MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
503 MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
504 MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
505 MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
506 MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
507 MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
508 MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
509 MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
510 MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
511 MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
512 MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
513 MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
514 >;
515 };
516
517 pinctrl_pwm1: pwm1-grp {
518 fsl,pins = <
519 MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0
520 >;
521 };
522
523 pinctrl_sai2: sai2-grp {
524 fsl,pins = <
525 MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x130b0
526 MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088
527 MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088
528 MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x120b0
529 >;
530 };
531
532 pinctrl_tsc: tsc-grp {
533 fsl,pins = <
534 MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0
535 MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
536 MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
537 MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0
538 >;
539 };
540
541 pinctrl_uart1: uart1-grp {
542 fsl,pins = <
543 MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
544 MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
545 >;
546 };
547
548 pinctrl_uart6: uart6-grp {
549 fsl,pins = <
550 MX6UL_PAD_CSI_MCLK__UART6_DCE_TX 0x1b0b1
551 MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX 0x1b0b1
552 MX6UL_PAD_CSI_VSYNC__UART6_DCE_RTS 0x1b0b1
553 MX6UL_PAD_CSI_HSYNC__UART6_DCE_CTS 0x1b0b1
554 >;
555 };
556
557 pinctrl_usbotg1: usbotg1-grp {
558 fsl,pins = <
559 MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
560 >;
561 };
562
563 pinctrl_usbotg2: usbotg2-grp {
564 fsl,pins = <
565 MX6UL_PAD_GPIO1_IO05__GPIO1_IO05 0x120b0
566 >;
567 };
568
569 pinctrl_usdhc2: usdhc2-grp {
570 fsl,pins = <
571 MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069
572 MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
573 MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
574 MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
575 MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
576 MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
577 MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
578 MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
579 MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
580 MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
581 MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x17059 /* SD2 Reset */
582 >;
583 };
584};
585
586&iomuxc_snvs {
587 /* DHCOM GPIOs A..H */
588 pinctrl_snvs_dhcom_a: snvs-dhcom-a-grp {
589 fsl,pins = <MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x400120b0>;
590 };
591
592 pinctrl_snvs_dhcom_b: snvs-dhcom-b-grp {
593 fsl,pins = <MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x400120b0>;
594 };
595
596 pinctrl_snvs_dhcom_c: snvs-dhcom-c-grp {
597 fsl,pins = <MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x400120b0>;
598 };
599
600 pinctrl_snvs_dhcom_d: snvs-dhcom-d-grp {
601 fsl,pins = <MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x400120b0>;
602 };
603
604 pinctrl_snvs_dhcom_e: snvs-dhcom-e-grp {
605 fsl,pins = <MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x400120b0>;
606 };
607
608 pinctrl_snvs_dhcom_f: snvs-dhcom-f-grp {
609 fsl,pins = <MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x400120b0>;
610 };
611
612 pinctrl_snvs_dhcom_g: snvs-dhcom-g-grp {
613 fsl,pins = <MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x400120b0>;
614 };
615
616 pinctrl_snvs_dhcom_h: snvs-dhcom-h-grp {
617 fsl,pins = <MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x400120b0>;
618 };
619
620 pinctrl_snvs_fec1_phy: snvs-fec1-phy-grp {
621 fsl,pins = <
622 MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05 0xb1 /* SMSC PHY Int */
623 >;
624 };
625
626 pinctrl_snvs_fec2_phy: snvs-fec2-phy-grp {
627 fsl,pins = <
628 MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06 0xb1 /* SMSC PHY Int */
629 >;
630 };
631};