Horatiu Vultur | 5cc72e8 | 2019-01-23 16:39:44 +0100 | [diff] [blame] | 1 | // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 | /* |
| 3 | * Copyright (c) 2018 Microsemi Corporation |
| 4 | */ |
| 5 | |
| 6 | /dts-v1/; |
| 7 | #include "mscc,serval.dtsi" |
Horatiu Vultur | 3ac7bc7 | 2019-04-11 14:11:34 +0200 | [diff] [blame] | 8 | #include <dt-bindings/mscc/serval_data.h> |
Horatiu Vultur | 5cc72e8 | 2019-01-23 16:39:44 +0100 | [diff] [blame] | 9 | |
| 10 | / { |
| 11 | model = "Serval PCB106 Reference Board"; |
| 12 | compatible = "mscc,serval-pcb106", "mscc,serval"; |
| 13 | |
| 14 | aliases { |
| 15 | spi0 = &spi0; |
| 16 | serial0 = &uart0; |
| 17 | }; |
| 18 | |
| 19 | chosen { |
| 20 | stdout-path = "serial0:115200n8"; |
| 21 | }; |
| 22 | |
| 23 | gpio-leds { |
| 24 | compatible = "gpio-leds"; |
| 25 | |
| 26 | status_green { |
| 27 | label = "pcb106:green:status"; |
| 28 | gpios = <&sgpio 43 1>; /* p11.1 */ |
| 29 | default-state = "on"; |
| 30 | }; |
| 31 | |
| 32 | status_red { |
| 33 | label = "pcb106:red:status"; |
| 34 | gpios = <&sgpio 11 1>; /* p11.0 */ |
| 35 | default-state = "off"; |
| 36 | }; |
| 37 | }; |
| 38 | }; |
| 39 | |
| 40 | &uart0 { |
| 41 | status = "okay"; |
| 42 | }; |
| 43 | |
| 44 | &spi0 { |
| 45 | status = "okay"; |
| 46 | spi-flash@0 { |
Neil Armstrong | a009fa7 | 2019-02-10 10:16:20 +0000 | [diff] [blame] | 47 | compatible = "jedec,spi-nor"; |
Horatiu Vultur | 5cc72e8 | 2019-01-23 16:39:44 +0100 | [diff] [blame] | 48 | spi-max-frequency = <18000000>; /* input clock */ |
| 49 | reg = <0>; /* CS0 */ |
| 50 | spi-cs-high; |
| 51 | }; |
| 52 | }; |
| 53 | |
| 54 | &sgpio { |
| 55 | status = "okay"; |
| 56 | sgpio-ports = <0x00FFFFFF>; |
| 57 | }; |
Horatiu Vultur | 3ac7bc7 | 2019-04-11 14:11:34 +0200 | [diff] [blame] | 58 | |
| 59 | &mdio1 { |
| 60 | status = "okay"; |
| 61 | |
| 62 | phy16: ethernet-phy@16 { |
| 63 | reg = <16>; |
| 64 | }; |
| 65 | phy17: ethernet-phy@17 { |
| 66 | reg = <17>; |
| 67 | }; |
| 68 | phy18: ethernet-phy@18 { |
| 69 | reg = <18>; |
| 70 | }; |
| 71 | phy19: ethernet-phy@19 { |
| 72 | reg = <19>; |
| 73 | }; |
| 74 | }; |
| 75 | |
| 76 | &switch { |
| 77 | ethernet-ports { |
| 78 | |
| 79 | port0: port@0 { |
| 80 | reg = <7>; |
| 81 | phy-handle = <&phy16>; |
| 82 | phys = <&serdes_hsio 7 SERDES1G(7) PHY_MODE_SGMII>; |
| 83 | }; |
| 84 | port1: port@1 { |
| 85 | reg = <6>; |
| 86 | phy-handle = <&phy17>; |
| 87 | phys = <&serdes_hsio 6 SERDES1G(6) PHY_MODE_SGMII>; |
| 88 | }; |
| 89 | port2: port@2 { |
| 90 | reg = <5>; |
| 91 | phy-handle = <&phy18>; |
| 92 | phys = <&serdes_hsio 5 SERDES1G(5) PHY_MODE_SGMII>; |
| 93 | }; |
| 94 | port3: port@3 { |
| 95 | reg = <4>; |
| 96 | phy-handle = <&phy19>; |
| 97 | phys = <&serdes_hsio 4 SERDES1G(4) PHY_MODE_SGMII>; |
| 98 | }; |
| 99 | }; |
| 100 | }; |