| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame] | 1 | // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 | /* |
| 3 | * Google Lazor board device tree source |
| 4 | * |
| 5 | * Copyright 2020 Google LLC. |
| 6 | */ |
| 7 | |
| 8 | /* This file must be included after sc7180-trogdor.dtsi */ |
| 9 | #include <arm/cros-ec-keyboard.dtsi> |
| 10 | |
| 11 | &ap_sar_sensor { |
| 12 | semtech,cs0-ground; |
| 13 | semtech,combined-sensors = <3>; |
| 14 | semtech,resolution = "fine"; |
| 15 | semtech,startup-sensor = <0>; |
| 16 | semtech,proxraw-strength = <8>; |
| 17 | semtech,avg-pos-strength = <64>; |
| 18 | }; |
| 19 | |
| 20 | &ap_tp_i2c { |
| 21 | status = "okay"; |
| 22 | }; |
| 23 | |
| 24 | /* |
| 25 | * Lazor is stuffed with a 47k NTC as charger thermistor which currently is |
| 26 | * not supported by the PM6150 ADC driver. Disable the charger thermal zone |
| 27 | * to avoid using bogus temperature values. |
| 28 | */ |
| 29 | &charger_thermal { |
| 30 | status = "disabled"; |
| 31 | }; |
| 32 | |
| 33 | ap_ts_pen_1v8: &i2c4 { |
| 34 | status = "okay"; |
| 35 | clock-frequency = <400000>; |
| 36 | |
| 37 | ap_ts: touchscreen@10 { |
| 38 | compatible = "hid-over-i2c"; |
| 39 | reg = <0x10>; |
| 40 | pinctrl-names = "default"; |
| 41 | pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; |
| 42 | |
| 43 | interrupt-parent = <&tlmm>; |
| 44 | interrupts = <9 IRQ_TYPE_LEVEL_LOW>; |
| 45 | |
| 46 | panel = <&panel>; |
| 47 | post-power-on-delay-ms = <20>; |
| 48 | hid-descr-addr = <0x0001>; |
| 49 | |
| 50 | vdd-supply = <&pp3300_ts>; |
| 51 | }; |
| 52 | }; |
| 53 | |
| 54 | &panel { |
| 55 | compatible = "boe,nv133fhm-n62"; |
| 56 | }; |
| 57 | |
| 58 | &pm6150_adc { |
| 59 | /delete-node/ channel@4f; |
| 60 | }; |
| 61 | |
| 62 | &pm6150_adc_tm { |
| 63 | status = "disabled"; |
| 64 | |
| 65 | /delete-node/ charger-thermistor@0; |
| 66 | }; |
| 67 | |
| 68 | &trackpad { |
| 69 | interrupts = <58 IRQ_TYPE_EDGE_FALLING>; |
| 70 | }; |
| 71 | |
| 72 | &wifi { |
| 73 | qcom,ath10k-calibration-variant = "GO_LAZOR"; |
| 74 | }; |
| 75 | |
| 76 | /* PINCTRL - modifications to sc7180-trogdor.dtsi */ |
| 77 | |
| 78 | &trackpad_int_1v8_odl { |
| 79 | pins = "gpio58"; |
| 80 | }; |
| 81 | |
| 82 | &ts_reset_l { |
| 83 | /* This pin is not connected on -rev0, pull up to park. */ |
| 84 | /delete-property/bias-disable; |
| 85 | bias-pull-up; |
| 86 | }; |
| 87 | |
| 88 | /* PINCTRL - board-specific pinctrl */ |
| 89 | |
| 90 | &tlmm { |
| 91 | gpio-line-names = "ESIM_MISO", |
| 92 | "ESIM_MOSI", |
| 93 | "ESIM_CLK", |
| 94 | "ESIM_CS_L", |
| 95 | "", |
| 96 | "", |
| 97 | "AP_TP_I2C_SDA", |
| 98 | "AP_TP_I2C_SCL", |
| 99 | "TS_RESET_L", |
| 100 | "TS_INT_L", |
| 101 | "", |
| 102 | "EDP_BRIJ_IRQ", |
| 103 | "AP_EDP_BKLTEN", |
| 104 | "AP_RAM_ID2", |
| 105 | "", |
| 106 | "EDP_BRIJ_I2C_SDA", |
| 107 | "EDP_BRIJ_I2C_SCL", |
| 108 | "HUB_RST_L", |
| 109 | "", |
| 110 | "AP_RAM_ID1", |
| 111 | "AP_SKU_ID2", |
| 112 | "", |
| 113 | "", |
| 114 | "AMP_EN", |
| 115 | "P_SENSOR_INT_L", |
| 116 | "AP_SAR_SENSOR_SDA", |
| 117 | "AP_SAR_SENSOR_SCL", |
| 118 | "", |
| 119 | "HP_IRQ", |
| 120 | "AP_RAM_ID0", |
| 121 | "EN_PP3300_DX_EDP", |
| 122 | "AP_BRD_ID2", |
| 123 | "BRIJ_SUSPEND", |
| 124 | "AP_BRD_ID0", |
| 125 | "AP_H1_SPI_MISO", |
| 126 | "AP_H1_SPI_MOSI", |
| 127 | "AP_H1_SPI_CLK", |
| 128 | "AP_H1_SPI_CS_L", |
| 129 | "", |
| 130 | "", |
| 131 | "", |
| 132 | "", |
| 133 | "H1_AP_INT_ODL", |
| 134 | "", |
| 135 | "UART_AP_TX_DBG_RX", |
| 136 | "UART_DBG_TX_AP_RX", |
| 137 | "HP_I2C_SDA", |
| 138 | "HP_I2C_SCL", |
| 139 | "FORCED_USB_BOOT", |
| 140 | "", |
| 141 | "", |
| 142 | "AMP_DIN", |
| 143 | "", |
| 144 | "HP_BCLK", |
| 145 | "HP_LRCLK", |
| 146 | "HP_DOUT", |
| 147 | "HP_DIN", |
| 148 | "HP_MCLK", |
| 149 | "TRACKPAD_INT_1V8_ODL", |
| 150 | "AP_EC_SPI_MISO", |
| 151 | "AP_EC_SPI_MOSI", |
| 152 | "AP_EC_SPI_CLK", |
| 153 | "AP_EC_SPI_CS_L", |
| 154 | "AP_SPI_CLK", |
| 155 | "AP_SPI_MOSI", |
| 156 | "AP_SPI_MISO", |
| 157 | /* |
| 158 | * AP_FLASH_WP_L is crossystem ABI. Schematics |
| 159 | * call it BIOS_FLASH_WP_L. |
| 160 | */ |
| 161 | "AP_FLASH_WP_L", |
| 162 | "DBG_SPI_HOLD_L", |
| 163 | "AP_SPI_CS0_L", |
| 164 | "", |
| 165 | "", |
| 166 | "", |
| 167 | "", |
| 168 | "", |
| 169 | "", |
| 170 | "UIM2_DATA", |
| 171 | "UIM2_CLK", |
| 172 | "UIM2_RST", |
| 173 | "UIM2_PRESENT", |
| 174 | "UIM1_DATA", |
| 175 | "UIM1_CLK", |
| 176 | "UIM1_RST", |
| 177 | "", |
| 178 | "EN_PP3300_CODEC", |
| 179 | "EN_PP3300_HUB", |
| 180 | "", |
| 181 | "", |
| 182 | "", |
| 183 | "", |
| 184 | "", |
| 185 | "AP_SKU_ID1", |
| 186 | "AP_RST_REQ", |
| 187 | "", |
| 188 | "AP_BRD_ID1", |
| 189 | "AP_EC_INT_L", |
| 190 | "", |
| 191 | "", |
| 192 | "", |
| 193 | "", |
| 194 | "", |
| 195 | "", |
| 196 | "", |
| 197 | "", |
| 198 | "", |
| 199 | "EDP_BRIJ_EN", |
| 200 | "AP_SKU_ID0", |
| 201 | "", |
| 202 | "", |
| 203 | "", |
| 204 | "", |
| 205 | "", |
| 206 | "", |
| 207 | "", |
| 208 | "", |
| 209 | "", |
| 210 | "AP_TS_PEN_I2C_SDA", |
| 211 | "AP_TS_PEN_I2C_SCL", |
| 212 | "DP_HOT_PLUG_DET", |
| 213 | "EC_IN_RW_ODL"; |
| 214 | }; |