| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame] | 1 | // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 | |
| 3 | /dts-v1/; |
| 4 | |
| 5 | #include <dt-bindings/gpio/gpio.h> |
| 6 | #include "imx6q-ba16.dtsi" |
| 7 | |
| 8 | / { |
| 9 | model = "Advantech DMS-BA16"; |
| 10 | compatible = "advantech,imx6q-dms-ba16", "advantech,imx6q-ba16", "fsl,imx6q"; |
| 11 | |
| 12 | reg_usb_otg_vbus: regulator-usbotgvbus { |
| 13 | compatible = "regulator-fixed"; |
| 14 | regulator-name = "usb_otg_vbus"; |
| 15 | regulator-min-microvolt = <5000000>; |
| 16 | regulator-max-microvolt = <5000000>; |
| 17 | pinctrl-names = "default"; |
| 18 | pinctrl-0 = <&pinctrl_usbotgvbus>; |
| 19 | gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; |
| 20 | enable-active-high; |
| 21 | }; |
| 22 | |
| 23 | sys_mclk: clock-sys-mclk { |
| 24 | compatible = "fixed-clock"; |
| 25 | #clock-cells = <0>; |
| 26 | clock-frequency = <22000000>; |
| 27 | }; |
| 28 | |
| 29 | sound { |
| 30 | compatible = "fsl,imx6q-ba16-sgtl5000", |
| 31 | "fsl,imx-audio-sgtl5000"; |
| 32 | model = "imx6q-ba16-sgtl5000"; |
| 33 | ssi-controller = <&ssi1>; |
| 34 | audio-codec = <&sgtl5000>; |
| 35 | audio-routing = |
| 36 | "MIC_IN", "Mic Jack", |
| 37 | "Mic Jack", "Mic Bias", |
| 38 | "Headphone Jack", "HP_OUT"; |
| 39 | mux-int-port = <1>; |
| 40 | mux-ext-port = <4>; |
| 41 | }; |
| 42 | }; |
| 43 | |
| 44 | &ecspi5 { |
| 45 | cs-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; |
| 46 | pinctrl-names = "default"; |
| 47 | pinctrl-0 = <&pinctrl_ecspi5>; |
| 48 | status = "okay"; |
| 49 | |
| 50 | m25_eeprom: flash@0 { |
| 51 | compatible = "atmel,at25256B", "atmel,at25"; |
| 52 | spi-max-frequency = <20000000>; |
| 53 | size = <0x8000>; |
| 54 | pagesize = <64>; |
| 55 | reg = <0>; |
| 56 | address-width = <16>; |
| 57 | }; |
| 58 | }; |
| 59 | |
| 60 | &iomuxc { |
| 61 | pinctrl_i2c1_gpio: i2c1gpiogrp { |
| 62 | fsl,pins = < |
| 63 | MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x1b0b0 |
| 64 | MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x1b0b0 |
| 65 | >; |
| 66 | }; |
| 67 | |
| 68 | pinctrl_i2c2_gpio: i2c2gpiogrp { |
| 69 | fsl,pins = < |
| 70 | MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0 |
| 71 | MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x1b0b0 |
| 72 | >; |
| 73 | }; |
| 74 | |
| 75 | pinctrl_i2c3_gpio: i2c3gpiogrp { |
| 76 | fsl,pins = < |
| 77 | MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x1b0b0 |
| 78 | MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0 |
| 79 | >; |
| 80 | }; |
| 81 | |
| 82 | pinctrl_usbotgvbus: usbotgvbusgrp { |
| 83 | fsl,pins = < |
| 84 | MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 |
| 85 | MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0 |
| 86 | >; |
| 87 | }; |
| 88 | }; |
| 89 | |
| 90 | &i2c1 { |
| 91 | clock-frequency = <100000>; |
| 92 | pinctrl-names = "default"; |
| 93 | pinctrl-0 = <&pinctrl_i2c1>; |
| 94 | status = "okay"; |
| 95 | |
| 96 | sgtl5000: codec@a { |
| 97 | compatible = "fsl,sgtl5000"; |
| 98 | reg = <0x0a>; |
| 99 | #sound-dai-cells = <0>; |
| 100 | clocks = <&sys_mclk>; |
| 101 | lrclk-strength = <0x3>; |
| 102 | VDDA-supply = <®_1p8v>; |
| 103 | VDDIO-supply = <®_3p3v>; |
| 104 | }; |
| 105 | }; |
| 106 | |
| 107 | &pwm2 { |
| 108 | pinctrl-names = "default"; |
| 109 | pinctrl-0 = <&pinctrl_pwm2>; |
| 110 | status = "okay"; |
| 111 | }; |
| 112 | |
| 113 | &sata { |
| 114 | fsl,no-spread-spectrum; |
| 115 | fsl,transmit-atten-16ths = <12>; |
| 116 | fsl,transmit-boost-mdB = <3330>; |
| 117 | fsl,transmit-level-mV = <1133>; |
| 118 | fsl,receive-dpll-mode = <1>; |
| 119 | status = "okay"; |
| 120 | }; |
| 121 | |
| 122 | &usbotg { |
| 123 | vbus-supply = <®_usb_otg_vbus>; |
| 124 | pinctrl-names = "default"; |
| 125 | pinctrl-0 = <&pinctrl_usbotg>; |
| 126 | dr_mode = "otg"; |
| 127 | disable-over-current; |
| 128 | status = "okay"; |
| 129 | }; |
| 130 | |
| 131 | &usdhc4 { |
| 132 | pinctrl-names = "default"; |
| 133 | pinctrl-0 = <&pinctrl_usdhc4>; |
| 134 | bus-width = <8>; |
| 135 | cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; |
| 136 | no-1-8-v; |
| 137 | keep-power-in-suspend; |
| 138 | wakeup-source; |
| 139 | status = "okay"; |
| 140 | }; |