| Bo Shen | fd12de9 | 2013-11-15 11:12:37 +0800 | [diff] [blame] | 1 | /* |
| 2 | * Copyright (C) 2013 Atmel Corporation |
| 3 | * Bo Shen <voice.shen@atmel.com> |
| 4 | * |
| 5 | * SPDX-License-Identifier: GPL-2.0+ |
| 6 | */ |
| 7 | |
| 8 | #include <common.h> |
| 9 | #include <asm/io.h> |
| 10 | #include <asm/arch/atmel_mpddrc.h> |
| 11 | |
| 12 | static inline void atmel_mpddr_op(int mode, u32 ram_address) |
| 13 | { |
| 14 | struct atmel_mpddr *mpddr = (struct atmel_mpddr *)ATMEL_BASE_MPDDRC; |
| 15 | |
| 16 | writel(mode, &mpddr->mr); |
| 17 | writel(0, ram_address); |
| 18 | } |
| 19 | |
| 20 | int ddr2_init(const unsigned int ram_address, |
| 21 | const struct atmel_mpddr *mpddr_value) |
| 22 | { |
| 23 | struct atmel_mpddr *mpddr = (struct atmel_mpddr *)ATMEL_BASE_MPDDRC; |
| 24 | u32 ba_off, cr; |
| 25 | |
| 26 | /* Compute bank offset according to NC in configuration register */ |
| 27 | ba_off = (mpddr_value->cr & ATMEL_MPDDRC_CR_NC_MASK) + 9; |
| 28 | if (!(mpddr_value->cr & ATMEL_MPDDRC_CR_DECOD_INTERLEAVED)) |
| 29 | ba_off += ((mpddr->cr & ATMEL_MPDDRC_CR_NR_MASK) >> 2) + 11; |
| 30 | |
| 31 | ba_off += (mpddr_value->md & ATMEL_MPDDRC_MD_DBW_MASK) ? 1 : 2; |
| 32 | |
| 33 | /* Program the memory device type into the memory device register */ |
| 34 | writel(mpddr_value->md, &mpddr->md); |
| 35 | |
| 36 | /* Program the configuration register */ |
| 37 | writel(mpddr_value->cr, &mpddr->cr); |
| 38 | |
| 39 | /* Program the timing register */ |
| 40 | writel(mpddr_value->tpr0, &mpddr->tpr0); |
| 41 | writel(mpddr_value->tpr1, &mpddr->tpr1); |
| 42 | writel(mpddr_value->tpr2, &mpddr->tpr2); |
| 43 | |
| 44 | /* Issue a NOP command */ |
| 45 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address); |
| 46 | |
| 47 | /* A 200 us is provided to precede any signal toggle */ |
| 48 | udelay(200); |
| 49 | |
| 50 | /* Issue a NOP command */ |
| 51 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address); |
| 52 | |
| 53 | /* Issue an all banks precharge command */ |
| 54 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_PRCGALL_CMD, ram_address); |
| 55 | |
| 56 | /* Issue an extended mode register set(EMRS2) to choose operation */ |
| 57 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD, |
| 58 | ram_address + (0x2 << ba_off)); |
| 59 | |
| 60 | /* Issue an extended mode register set(EMRS3) to set EMSR to 0 */ |
| 61 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD, |
| 62 | ram_address + (0x3 << ba_off)); |
| 63 | |
| 64 | /* |
| 65 | * Issue an extended mode register set(EMRS1) to enable DLL and |
| 66 | * program D.I.C (output driver impedance control) |
| 67 | */ |
| 68 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD, |
| 69 | ram_address + (0x1 << ba_off)); |
| 70 | |
| 71 | /* Enable DLL reset */ |
| 72 | cr = readl(&mpddr->cr); |
| 73 | writel(cr | ATMEL_MPDDRC_CR_DLL_RESET_ENABLED, &mpddr->cr); |
| 74 | |
| 75 | /* A mode register set(MRS) cycle is issued to reset DLL */ |
| 76 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_LMR_CMD, ram_address); |
| 77 | |
| 78 | /* Issue an all banks precharge command */ |
| 79 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_PRCGALL_CMD, ram_address); |
| 80 | |
| 81 | /* Two auto-refresh (CBR) cycles are provided */ |
| 82 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_RFSH_CMD, ram_address); |
| 83 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_RFSH_CMD, ram_address); |
| 84 | |
| 85 | /* Disable DLL reset */ |
| 86 | cr = readl(&mpddr->cr); |
| 87 | writel(cr & (~ATMEL_MPDDRC_CR_DLL_RESET_ENABLED), &mpddr->cr); |
| 88 | |
| 89 | /* A mode register set (MRS) cycle is issued to disable DLL reset */ |
| 90 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_LMR_CMD, ram_address); |
| 91 | |
| 92 | /* Set OCD calibration in default state */ |
| 93 | cr = readl(&mpddr->cr); |
| 94 | writel(cr | ATMEL_MPDDRC_CR_OCD_DEFAULT, &mpddr->cr); |
| 95 | |
| 96 | /* |
| 97 | * An extended mode register set (EMRS1) cycle is issued |
| 98 | * to OCD default value |
| 99 | */ |
| 100 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD, |
| 101 | ram_address + (0x1 << ba_off)); |
| 102 | |
| 103 | /* OCD calibration mode exit */ |
| 104 | cr = readl(&mpddr->cr); |
| 105 | writel(cr & (~ATMEL_MPDDRC_CR_OCD_DEFAULT), &mpddr->cr); |
| 106 | |
| 107 | /* |
| 108 | * An extended mode register set (EMRS1) cycle is issued |
| 109 | * to enable OCD exit |
| 110 | */ |
| 111 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD, |
| 112 | ram_address + (0x1 << ba_off)); |
| 113 | |
| 114 | /* A nornal mode command is provided */ |
| 115 | atmel_mpddr_op(ATMEL_MPDDRC_MR_MODE_NORMAL_CMD, ram_address); |
| 116 | |
| 117 | /* Perform a write access to any DDR2-SDRAM address */ |
| 118 | writel(0, ram_address); |
| 119 | |
| 120 | /* Write the refresh rate */ |
| 121 | writel(mpddr_value->rtr, &mpddr->rtr); |
| 122 | |
| 123 | return 0; |
| 124 | } |