Stefan Roese | 9e29eff | 2020-06-30 12:08:57 +0200 | [diff] [blame] | 1 | // SPDX-License-Identifier: GPL-2.0+ |
| 2 | /* |
| 3 | * Marvell / Cavium Inc. CN73xx |
| 4 | */ |
| 5 | |
| 6 | /dts-v1/; |
| 7 | |
Stefan Roese | 1faed61 | 2020-07-30 13:56:17 +0200 | [diff] [blame] | 8 | #include <dt-bindings/clock/octeon-clock.h> |
| 9 | |
Stefan Roese | 9e29eff | 2020-06-30 12:08:57 +0200 | [diff] [blame] | 10 | / { |
| 11 | #address-cells = <2>; |
| 12 | #size-cells = <2>; |
| 13 | |
| 14 | soc0: soc@0 { |
| 15 | interrupt-parent = <&ciu3>; |
| 16 | compatible = "simple-bus"; |
| 17 | #address-cells = <2>; |
| 18 | #size-cells = <2>; |
| 19 | ranges; /* Direct mapping */ |
| 20 | |
| 21 | ciu3: interrupt-controller@1010000000000 { |
| 22 | compatible = "cavium,octeon-7890-ciu3"; |
| 23 | interrupt-controller; |
| 24 | /* |
| 25 | * Interrupts are specified by two parts: |
| 26 | * 1) Source number (20 significant bits) |
| 27 | * 2) Trigger type: (4 == level, 1 == edge) |
| 28 | */ |
| 29 | #address-cells = <0>; |
| 30 | #interrupt-cells = <2>; |
| 31 | reg = <0x10100 0x00000000 0x0 0xb0000000>; |
| 32 | }; |
| 33 | |
| 34 | bootbus: bootbus@1180000000000 { |
| 35 | compatible = "cavium,octeon-3860-bootbus","simple-bus"; |
| 36 | reg = <0x11800 0x00000000 0x0 0x200>; |
| 37 | /* The chip select number and offset */ |
| 38 | #address-cells = <2>; |
| 39 | /* The size of the chip select region */ |
| 40 | #size-cells = <1>; |
| 41 | }; |
| 42 | |
Stefan Roese | 1faed61 | 2020-07-30 13:56:17 +0200 | [diff] [blame] | 43 | clk: clock { |
| 44 | compatible = "mrvl,octeon-clk"; |
| 45 | #clock-cells = <1>; |
| 46 | u-boot,dm-pre-reloc; |
| 47 | }; |
| 48 | |
Stefan Roese | 7bce6c0 | 2020-07-30 13:56:14 +0200 | [diff] [blame] | 49 | gpio: gpio-controller@1070000000800 { |
| 50 | #gpio-cells = <2>; |
| 51 | compatible = "cavium,octeon-7890-gpio"; |
| 52 | reg = <0x10700 0x00000800 0x0 0x100>; |
| 53 | gpio-controller; |
| 54 | nr-gpios = <32>; |
| 55 | /* Interrupts are specified by two parts: |
| 56 | * 1) GPIO pin number (0..15) |
| 57 | * 2) Triggering (1 - edge rising |
| 58 | * 2 - edge falling |
| 59 | * 4 - level active high |
| 60 | * 8 - level active low) |
| 61 | */ |
| 62 | interrupt-controller; |
| 63 | #interrupt-cells = <2>; |
| 64 | /* The GPIO pins connect to 16 consecutive CUI bits */ |
| 65 | interrupts = <0x03000 4>, <0x03001 4>, |
| 66 | <0x03002 4>, <0x03003 4>, |
| 67 | <0x03004 4>, <0x03005 4>, |
| 68 | <0x03006 4>, <0x03007 4>, |
| 69 | <0x03008 4>, <0x03009 4>, |
| 70 | <0x0300a 4>, <0x0300b 4>, |
| 71 | <0x0300c 4>, <0x0300d 4>, |
| 72 | <0x0300e 4>, <0x0300f 4>; |
| 73 | }; |
| 74 | |
Stefan Roese | e9aa953 | 2020-09-02 08:29:02 +0200 | [diff] [blame] | 75 | l2c: l2c@1180080000000 { |
| 76 | #address-cells = <1>; |
| 77 | #size-cells = <0>; |
| 78 | compatible = "cavium,octeon-7xxx-l2c"; |
| 79 | reg = <0x11800 0x80000000 0x0 0x01000000>; |
| 80 | u-boot,dm-pre-reloc; |
| 81 | }; |
| 82 | |
| 83 | lmc: lmc@1180088000000 { |
| 84 | #address-cells = <1>; |
| 85 | #size-cells = <0>; |
| 86 | compatible = "cavium,octeon-7xxx-ddr4"; |
| 87 | reg = <0x11800 0x88000000 0x0 0x02000000>; // 2 IFs |
| 88 | u-boot,dm-pre-reloc; |
| 89 | l2c-handle = <&l2c>; |
| 90 | }; |
| 91 | |
Stefan Roese | 9e29eff | 2020-06-30 12:08:57 +0200 | [diff] [blame] | 92 | reset: reset@1180006001600 { |
| 93 | compatible = "mrvl,cn7xxx-rst"; |
| 94 | reg = <0x11800 0x06001600 0x0 0x200>; |
| 95 | }; |
| 96 | |
| 97 | uart0: serial@1180000000800 { |
| 98 | compatible = "cavium,octeon-3860-uart","ns16550"; |
| 99 | reg = <0x11800 0x00000800 0x0 0x400>; |
Aaron Williams | 07cd14f | 2021-04-07 09:12:39 +0200 | [diff] [blame] | 100 | clocks = <&clk OCTEON_CLK_IO>; |
Stefan Roese | 9e29eff | 2020-06-30 12:08:57 +0200 | [diff] [blame] | 101 | clock-frequency = <0>; |
| 102 | current-speed = <115200>; |
| 103 | reg-shift = <3>; |
| 104 | interrupts = <0x08000 4>; |
| 105 | }; |
| 106 | |
| 107 | uart1: serial@1180000000c00 { |
| 108 | compatible = "cavium,octeon-3860-uart","ns16550"; |
| 109 | reg = <0x11800 0x00000c00 0x0 0x400>; |
Aaron Williams | 07cd14f | 2021-04-07 09:12:39 +0200 | [diff] [blame] | 110 | clocks = <&clk OCTEON_CLK_IO>; |
Stefan Roese | 9e29eff | 2020-06-30 12:08:57 +0200 | [diff] [blame] | 111 | clock-frequency = <0>; |
| 112 | current-speed = <115200>; |
| 113 | reg-shift = <3>; |
| 114 | interrupts = <0x08040 4>; |
| 115 | }; |
Stefan Roese | 42bbbfa | 2020-07-30 13:56:15 +0200 | [diff] [blame] | 116 | |
| 117 | i2c0: i2c@1180000001000 { |
| 118 | #address-cells = <1>; |
| 119 | #size-cells = <0>; |
| 120 | compatible = "cavium,octeon-7890-twsi"; |
| 121 | reg = <0x11800 0x00001000 0x0 0x200>; |
| 122 | /* INT_ST, INT_TS, INT_CORE */ |
| 123 | interrupts = <0x0b000 1>, <0x0b001 1>, <0x0b002 1>; |
| 124 | clock-frequency = <100000>; |
Stefan Roese | 1faed61 | 2020-07-30 13:56:17 +0200 | [diff] [blame] | 125 | clocks = <&clk OCTEON_CLK_IO>; |
Stefan Roese | 42bbbfa | 2020-07-30 13:56:15 +0200 | [diff] [blame] | 126 | }; |
| 127 | |
| 128 | i2c1: i2c@1180000001200 { |
| 129 | #address-cells = <1>; |
| 130 | #size-cells = <0>; |
| 131 | compatible = "cavium,octeon-7890-twsi"; |
| 132 | reg = <0x11800 0x00001200 0x0 0x200>; |
| 133 | /* INT_ST, INT_TS, INT_CORE */ |
| 134 | interrupts = <0x0b100 1>, <0x0b101 1>, <0x0b102 1>; |
| 135 | clock-frequency = <100000>; |
Stefan Roese | 1faed61 | 2020-07-30 13:56:17 +0200 | [diff] [blame] | 136 | clocks = <&clk OCTEON_CLK_IO>; |
Stefan Roese | 42bbbfa | 2020-07-30 13:56:15 +0200 | [diff] [blame] | 137 | }; |
Stefan Roese | 35d4693 | 2020-07-30 13:56:19 +0200 | [diff] [blame] | 138 | |
Stefan Roese | be77652 | 2021-03-12 09:48:26 +0100 | [diff] [blame] | 139 | mmc: mmc@1180000002000 { |
| 140 | compatible = "cavium,octeon-7890-mmc", |
| 141 | "cavium,octeon-7360-mmc"; |
| 142 | reg = <0x11800 0x00000000 0x0 0x2100>; |
| 143 | #address-cells = <1>; |
| 144 | #size-cells = <0>; |
| 145 | /* EMM_INT_BUF_DONE, |
| 146 | EMM_INT_CMD_DONE, |
| 147 | EMM_INT_DMA_DONE, |
| 148 | EMM_INT_CMD_ERR, |
| 149 | EMM_INT_DMA_ERR, |
| 150 | EMM_INT_SWITCH_DONE, |
| 151 | EMM_INT_SWITCH_ERR, |
| 152 | EMM_DMA_DONE, |
| 153 | EMM_DMA_FIFO*/ |
| 154 | interrupts = <0x09040 1>, |
| 155 | <0x09041 1>, |
| 156 | <0x09042 1>, |
| 157 | <0x09043 1>, |
| 158 | <0x09044 1>, |
| 159 | <0x09045 1>, |
| 160 | <0x09046 1>, |
| 161 | <0x09000 1>, |
| 162 | <0x09001 1>; |
| 163 | clocks = <&clk OCTEON_CLK_IO>; |
| 164 | }; |
| 165 | |
Stefan Roese | 35d4693 | 2020-07-30 13:56:19 +0200 | [diff] [blame] | 166 | spi: spi@1070000001000 { |
| 167 | compatible = "cavium,octeon-3010-spi"; |
| 168 | reg = <0x10700 0x00001000 0x0 0x100>; |
| 169 | interrupts = <0x05001 1>; |
| 170 | #address-cells = <1>; |
| 171 | #size-cells = <0>; |
| 172 | spi-max-frequency = <25000000>; |
| 173 | clocks = <&clk OCTEON_CLK_IO>; |
| 174 | }; |
Stefan Roese | 3e08317 | 2020-08-24 13:04:42 +0200 | [diff] [blame] | 175 | |
| 176 | /* USB 0 */ |
| 177 | usb0: uctl@1180068000000 { |
| 178 | compatible = "cavium,octeon-7130-usb-uctl"; |
| 179 | reg = <0x11800 0x68000000 0x0 0x100>; |
| 180 | ranges; /* Direct mapping */ |
| 181 | #address-cells = <2>; |
| 182 | #size-cells = <2>; |
| 183 | /* Only 100MHz allowed */ |
| 184 | refclk-frequency = <100000000>; |
| 185 | /* Only "dlmc_ref_clk0" is supported for 73xx */ |
| 186 | refclk-type-ss = "dlmc_ref_clk0"; |
| 187 | /* Only "dlmc_ref_clk0" is supported for 73xx */ |
| 188 | refclk-type-hs = "dlmc_ref_clk0"; |
| 189 | |
| 190 | /* |
| 191 | * Power is specified by three parts: |
| 192 | * 1) GPIO handle (must be &gpio) |
| 193 | * 2) GPIO pin number |
| 194 | * 3) Active high (0) or active low (1) |
| 195 | */ |
| 196 | xhci@1680000000000 { |
| 197 | compatible = "cavium,octeon-7130-xhci","synopsys,dwc3","snps,dwc3"; |
| 198 | reg = <0x16800 0x00000000 0x10 0x0>; |
| 199 | interrupts = <0x68080 4>; /* UAHC_IMAN, level */ |
| 200 | maximum-speed = "super-speed"; |
| 201 | dr_mode = "host"; |
| 202 | snps,dis_u3_susphy_quirk; |
| 203 | snps,dis_u2_susphy_quirk; |
| 204 | snps,dis_enblslpm_quirk; |
| 205 | }; |
| 206 | }; |
| 207 | |
| 208 | /* USB 1 */ |
| 209 | usb1: uctl@1180069000000 { |
| 210 | compatible = "cavium,octeon-7130-usb-uctl"; |
| 211 | reg = <0x11800 0x69000000 0x0 0x100>; |
| 212 | ranges; /* Direct mapping */ |
| 213 | #address-cells = <2>; |
| 214 | #size-cells = <2>; |
| 215 | /* 50MHz, 100MHz and 125MHz allowed */ |
| 216 | refclk-frequency = <100000000>; |
| 217 | /* Either "dlmc_ref_clk0" or "dlmc_ref_clk0" */ |
| 218 | refclk-type-ss = "dlmc_ref_clk0"; |
| 219 | /* Either "dlmc_ref_clk0" "dlmc_ref_clk1" or "pll_ref_clk" */ |
| 220 | refclk-type-hs = "dlmc_ref_clk0"; |
| 221 | |
| 222 | /* |
| 223 | * Power is specified by three parts: |
| 224 | * 1) GPIO handle (must be &gpio) |
| 225 | * 2) GPIO pin number |
| 226 | * 3) Active high (0) or active low (1) |
| 227 | */ |
| 228 | xhci@1690000000000 { |
| 229 | compatible = "cavium,octeon-7130-xhci","synopsys,dwc3","snps,dwc3"; |
| 230 | reg = <0x16900 0x00000000 0x10 0x0>; |
| 231 | interrupts = <0x69080 4>; /* UAHC_IMAN, level */ |
| 232 | dr_mode = "host"; |
| 233 | }; |
| 234 | }; |
Stefan Roese | 1e4518c | 2020-12-11 17:06:09 +0100 | [diff] [blame] | 235 | |
| 236 | /* PCIe 0 */ |
| 237 | pcie0: pcie@1180069000000 { |
| 238 | compatible = "marvell,pcie-host-octeon"; |
| 239 | reg = <0 0xf2600000 0 0x10000>; |
| 240 | #address-cells = <3>; |
| 241 | #size-cells = <2>; |
| 242 | device_type = "pci"; |
| 243 | dma-coherent; |
| 244 | |
| 245 | bus-range = <0 0xff>; |
| 246 | marvell,pcie-port = <0>; |
| 247 | ranges = <0x81000000 0x00000000 0xd0000000 0x00011a00 0xd0000000 0x00000000 0x01000000 /* IO */ |
| 248 | 0x02000000 0x00000000 0xe0000000 0x00011b00 0xe0000000 0x00000000 0x10000000 /* non-prefetchable memory */ |
| 249 | 0x43000000 0x00011c00 0x00000000 0x00011c00 0x00000000 0x00000010 0x00000000>;/* prefetchable memory */ |
| 250 | }; |
Stefan Roese | 5f7b821 | 2021-04-07 09:12:37 +0200 | [diff] [blame] | 251 | |
| 252 | uctl@118006c000000 { |
| 253 | compatible = "cavium,octeon-7130-sata-uctl", "simple-bus"; |
| 254 | reg = <0x11800 0x6c000000 0x0 0x100>; |
| 255 | ranges; /* Direct mapping */ |
| 256 | #address-cells = <2>; |
| 257 | #size-cells = <2>; |
| 258 | portmap = <0x3>; |
| 259 | staggered-spinup; |
| 260 | cavium,qlm-trim = "4,sata"; |
| 261 | |
| 262 | sata: sata@16c0000000000 { |
| 263 | compatible = "cavium,octeon-7130-ahci"; |
| 264 | reg = <0x16c00 0x00000000 0x0 0x200>; |
| 265 | #address-cells = <2>; |
| 266 | #size-cells = <2>; |
| 267 | interrupts = <0x6c010 4>; |
| 268 | }; |
| 269 | }; |
Stefan Roese | 734cecd | 2022-04-07 09:11:49 +0200 | [diff] [blame] | 270 | |
| 271 | /* SMI1 */ |
| 272 | smi1: mdio@1180000003880 { |
| 273 | compatible = "cavium,octeon-3860-mdio"; |
| 274 | reg = <0x11800 0x00003880 0x0 0x40>; |
| 275 | #address-cells = <1>; |
| 276 | #size-cells = <0>; |
| 277 | }; |
| 278 | |
| 279 | /* BGX 0 */ |
| 280 | bgx0: ethernet-mac-nexus@11800e0000000 { |
| 281 | compatible = "cavium,octeon-7890-bgx"; |
| 282 | reg = <0x11800 0xe0000000 0x0 0x1000000>; |
| 283 | #address-cells = <1>; |
| 284 | #size-cells = <0>; |
| 285 | status = "disabled"; |
| 286 | }; |
| 287 | |
| 288 | /* BGX 1 */ |
| 289 | bgx1: ethernet-mac-nexus@11800e1000000 { |
| 290 | compatible = "cavium,octeon-7890-bgx"; |
| 291 | reg = <0x11800 0xe1000000 0x0 0x1000000>; |
| 292 | #address-cells = <1>; |
| 293 | #size-cells = <0>; |
| 294 | status = "disabled"; |
| 295 | }; |
| 296 | |
| 297 | /* BGX 2*/ |
| 298 | bgx2: ethernet-mac-nexus@11800e2000000 { |
| 299 | compatible = "cavium,octeon-7890-bgx"; |
| 300 | reg = <0x11800 0xe2000000 0x0 0x1000000>; |
| 301 | #address-cells = <1>; |
| 302 | #size-cells = <0>; |
| 303 | status = "disabled"; |
| 304 | }; |
Stefan Roese | 9e29eff | 2020-06-30 12:08:57 +0200 | [diff] [blame] | 305 | }; |
| 306 | }; |