| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame] | 1 | NVIDIA Tegra NAND Flash controller |
| 2 | |
| 3 | Required properties: |
| 4 | - compatible: Must be one of: |
| 5 | - "nvidia,tegra20-nand" |
| 6 | - reg: MMIO address range |
| 7 | - interrupts: interrupt output of the NFC controller |
| 8 | - clocks: Must contain an entry for each entry in clock-names. |
| 9 | See ../clocks/clock-bindings.txt for details. |
| 10 | - clock-names: Must include the following entries: |
| 11 | - nand |
| 12 | - resets: Must contain an entry for each entry in reset-names. |
| 13 | See ../reset/reset.txt for details. |
| 14 | - reset-names: Must include the following entries: |
| 15 | - nand |
| 16 | |
| 17 | Optional children nodes: |
| 18 | Individual NAND chips are children of the NAND controller node. Currently |
| 19 | only one NAND chip supported. |
| 20 | |
| 21 | Required children node properties: |
| 22 | - reg: An integer ranging from 1 to 6 representing the CS line to use. |
| 23 | |
| 24 | Optional children node properties: |
| 25 | - nand-ecc-mode: String, operation mode of the NAND ecc mode. Currently only |
| 26 | "hw" is supported. |
| 27 | - nand-ecc-algo: string, algorithm of NAND ECC. |
| 28 | Supported values with "hw" ECC mode are: "rs", "bch". |
| 29 | - nand-bus-width : See nand-controller.yaml |
| 30 | - nand-on-flash-bbt: See nand-controller.yaml |
| 31 | - nand-ecc-strength: integer representing the number of bits to correct |
| 32 | per ECC step (always 512). Supported strength using HW ECC |
| 33 | modes are: |
| 34 | - RS: 4, 6, 8 |
| 35 | - BCH: 4, 8, 14, 16 |
| 36 | - nand-ecc-maximize: See nand-controller.yaml |
| 37 | - nand-is-boot-medium: Makes sure only ECC strengths supported by the boot ROM |
| 38 | are chosen. |
| 39 | - wp-gpios: GPIO specifier for the write protect pin. |
| 40 | |
| 41 | Optional child node of NAND chip nodes: |
| Tom Rini | 6bb92fc | 2024-05-20 09:54:58 -0600 | [diff] [blame^] | 42 | Partitions: see mtd.yaml |
| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame] | 43 | |
| 44 | Example: |
| 45 | nand-controller@70008000 { |
| 46 | compatible = "nvidia,tegra20-nand"; |
| 47 | reg = <0x70008000 0x100>; |
| 48 | interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; |
| 49 | clocks = <&tegra_car TEGRA20_CLK_NDFLASH>; |
| 50 | clock-names = "nand"; |
| 51 | resets = <&tegra_car 13>; |
| 52 | reset-names = "nand"; |
| 53 | |
| 54 | nand@0 { |
| 55 | reg = <0>; |
| 56 | #address-cells = <1>; |
| 57 | #size-cells = <1>; |
| 58 | nand-bus-width = <8>; |
| 59 | nand-on-flash-bbt; |
| 60 | nand-ecc-algo = "bch"; |
| 61 | nand-ecc-strength = <8>; |
| 62 | wp-gpios = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_LOW>; |
| 63 | }; |
| 64 | }; |