| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame] | 1 | // SPDX-License-Identifier: BSD-3-Clause |
| 2 | /* |
| 3 | * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. |
| 4 | * Copyright (c) 2019, Linaro Limited |
| 5 | */ |
| 6 | |
| 7 | #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| 8 | #include <dt-bindings/interrupt-controller/irq.h> |
| 9 | #include <dt-bindings/spmi/spmi.h> |
| 10 | |
| 11 | / { |
| 12 | thermal-zones { |
| 13 | pm8150l-thermal { |
| 14 | polling-delay-passive = <100>; |
| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame] | 15 | |
| 16 | thermal-sensors = <&pm8150l_temp>; |
| 17 | |
| 18 | trips { |
| 19 | trip0 { |
| 20 | temperature = <95000>; |
| 21 | hysteresis = <0>; |
| 22 | type = "passive"; |
| 23 | }; |
| 24 | |
| 25 | trip1 { |
| 26 | temperature = <115000>; |
| 27 | hysteresis = <0>; |
| 28 | type = "hot"; |
| 29 | }; |
| 30 | |
| 31 | trip2 { |
| 32 | temperature = <145000>; |
| 33 | hysteresis = <0>; |
| 34 | type = "critical"; |
| 35 | }; |
| 36 | }; |
| 37 | }; |
| 38 | }; |
| 39 | }; |
| 40 | |
| 41 | &spmi_bus { |
| 42 | pmic@4 { |
| 43 | compatible = "qcom,pm8150l", "qcom,spmi-pmic"; |
| 44 | reg = <0x4 SPMI_USID>; |
| 45 | #address-cells = <1>; |
| 46 | #size-cells = <0>; |
| 47 | |
| 48 | pon@800 { |
| 49 | compatible = "qcom,pm8916-pon"; |
| 50 | reg = <0x0800>; |
| 51 | |
| 52 | status = "disabled"; |
| 53 | }; |
| 54 | |
| 55 | pm8150l_temp: temp-alarm@2400 { |
| 56 | compatible = "qcom,spmi-temp-alarm"; |
| 57 | reg = <0x2400>; |
| 58 | interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; |
| 59 | io-channels = <&pm8150l_adc ADC5_DIE_TEMP>; |
| 60 | io-channel-names = "thermal"; |
| 61 | #thermal-sensor-cells = <0>; |
| 62 | }; |
| 63 | |
| 64 | pm8150l_adc: adc@3100 { |
| 65 | compatible = "qcom,spmi-adc5"; |
| 66 | reg = <0x3100>; |
| 67 | #address-cells = <1>; |
| 68 | #size-cells = <0>; |
| 69 | #io-channel-cells = <1>; |
| 70 | interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| 71 | |
| 72 | channel@0 { |
| 73 | reg = <ADC5_REF_GND>; |
| 74 | qcom,pre-scaling = <1 1>; |
| 75 | label = "ref_gnd"; |
| 76 | }; |
| 77 | |
| 78 | channel@1 { |
| 79 | reg = <ADC5_1P25VREF>; |
| 80 | qcom,pre-scaling = <1 1>; |
| 81 | label = "vref_1p25"; |
| 82 | }; |
| 83 | |
| 84 | channel@6 { |
| 85 | reg = <ADC5_DIE_TEMP>; |
| 86 | qcom,pre-scaling = <1 1>; |
| 87 | label = "die_temp"; |
| 88 | }; |
| 89 | }; |
| 90 | |
| 91 | pm8150l_adc_tm: adc-tm@3500 { |
| 92 | compatible = "qcom,spmi-adc-tm5"; |
| 93 | reg = <0x3500>; |
| 94 | interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; |
| 95 | #thermal-sensor-cells = <1>; |
| 96 | #address-cells = <1>; |
| 97 | #size-cells = <0>; |
| 98 | status = "disabled"; |
| 99 | }; |
| 100 | |
| 101 | pm8150l_gpios: gpio@c000 { |
| 102 | compatible = "qcom,pm8150l-gpio", "qcom,spmi-gpio"; |
| 103 | reg = <0xc000>; |
| 104 | gpio-controller; |
| 105 | gpio-ranges = <&pm8150l_gpios 0 0 12>; |
| 106 | #gpio-cells = <2>; |
| 107 | interrupt-controller; |
| 108 | #interrupt-cells = <2>; |
| 109 | }; |
| 110 | }; |
| 111 | |
| 112 | pmic@5 { |
| 113 | compatible = "qcom,pm8150l", "qcom,spmi-pmic"; |
| 114 | reg = <0x5 SPMI_USID>; |
| 115 | #address-cells = <1>; |
| 116 | #size-cells = <0>; |
| 117 | |
| 118 | pm8150l_flash: led-controller@d300 { |
| 119 | compatible = "qcom,pm8150l-flash-led", "qcom,spmi-flash-led"; |
| 120 | reg = <0xd300>; |
| 121 | status = "disabled"; |
| 122 | }; |
| 123 | |
| 124 | pm8150l_lpg: pwm { |
| 125 | compatible = "qcom,pm8150l-lpg"; |
| 126 | |
| 127 | #address-cells = <1>; |
| 128 | #size-cells = <0>; |
| 129 | #pwm-cells = <2>; |
| 130 | |
| 131 | status = "disabled"; |
| 132 | }; |
| 133 | |
| 134 | pm8150l_wled: leds@d800 { |
| 135 | compatible = "qcom,pm8150l-wled"; |
| 136 | reg = <0xd800>, <0xd900>; |
| 137 | interrupts = <0x5 0xd8 0x1 IRQ_TYPE_EDGE_RISING>, |
| 138 | <0x5 0xd8 0x2 IRQ_TYPE_EDGE_RISING>; |
| 139 | interrupt-names = "ovp", "short"; |
| 140 | label = "backlight"; |
| 141 | |
| 142 | status = "disabled"; |
| 143 | }; |
| 144 | }; |
| 145 | }; |