| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame] | 1 | // SPDX-License-Identifier: BSD-3-Clause |
| 2 | |
| 3 | #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| 4 | #include <dt-bindings/input/input.h> |
| 5 | #include <dt-bindings/input/linux-event-codes.h> |
| 6 | #include <dt-bindings/interrupt-controller/irq.h> |
| 7 | #include <dt-bindings/spmi/spmi.h> |
| 8 | |
| 9 | / { |
| 10 | thermal-zones { |
| 11 | pm6125-thermal { |
| 12 | polling-delay-passive = <100>; |
| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame] | 13 | |
| 14 | thermal-sensors = <&pm6125_temp>; |
| 15 | |
| 16 | trips { |
| 17 | trip0 { |
| 18 | temperature = <95000>; |
| 19 | hysteresis = <0>; |
| 20 | type = "passive"; |
| 21 | }; |
| 22 | |
| 23 | trip1 { |
| 24 | temperature = <115000>; |
| 25 | hysteresis = <0>; |
| 26 | type = "hot"; |
| 27 | }; |
| 28 | |
| 29 | trip2 { |
| 30 | temperature = <145000>; |
| 31 | hysteresis = <0>; |
| 32 | type = "critical"; |
| 33 | }; |
| 34 | }; |
| 35 | }; |
| 36 | }; |
| 37 | }; |
| 38 | |
| 39 | &spmi_bus { |
| 40 | pmic@0 { |
| 41 | compatible = "qcom,pm6125", "qcom,spmi-pmic"; |
| 42 | reg = <0x0 SPMI_USID>; |
| 43 | #address-cells = <1>; |
| 44 | #size-cells = <0>; |
| 45 | |
| 46 | pm6125_pon: pon@800 { |
| 47 | compatible = "qcom,pm8998-pon"; |
| 48 | reg = <0x800>; |
| 49 | mode-bootloader = <0x2>; |
| 50 | mode-recovery = <0x1>; |
| 51 | |
| 52 | pon_pwrkey: pwrkey { |
| 53 | compatible = "qcom,pm8941-pwrkey"; |
| 54 | interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; |
| 55 | debounce = <15625>; |
| 56 | linux,code = <KEY_POWER>; |
| 57 | bias-pull-up; |
| 58 | status = "disabled"; |
| 59 | }; |
| 60 | |
| 61 | pon_resin: resin { |
| 62 | compatible = "qcom,pm8941-resin"; |
| 63 | interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>; |
| 64 | debounce = <15625>; |
| 65 | bias-pull-up; |
| 66 | status = "disabled"; |
| 67 | }; |
| 68 | }; |
| 69 | |
| 70 | pm6125_temp: temp-alarm@2400 { |
| 71 | compatible = "qcom,spmi-temp-alarm"; |
| 72 | reg = <0x2400>; |
| 73 | interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; |
| 74 | io-channels = <&pm6125_adc ADC5_DIE_TEMP>; |
| 75 | io-channel-names = "thermal"; |
| 76 | #thermal-sensor-cells = <0>; |
| 77 | }; |
| 78 | |
| 79 | pm6125_adc: adc@3100 { |
| 80 | compatible = "qcom,spmi-adc5"; |
| 81 | reg = <0x3100>; |
| 82 | #address-cells = <1>; |
| 83 | #size-cells = <0>; |
| 84 | interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| 85 | #io-channel-cells = <1>; |
| 86 | |
| 87 | channel@0 { |
| 88 | reg = <ADC5_REF_GND>; |
| 89 | qcom,pre-scaling = <1 1>; |
| 90 | label = "ref_gnd"; |
| 91 | }; |
| 92 | |
| 93 | channel@1 { |
| 94 | reg = <ADC5_1P25VREF>; |
| 95 | qcom,pre-scaling = <1 1>; |
| 96 | label = "vref_1p25"; |
| 97 | }; |
| 98 | |
| 99 | channel@6 { |
| 100 | reg = <ADC5_DIE_TEMP>; |
| 101 | qcom,pre-scaling = <1 1>; |
| 102 | label = "die_temp"; |
| 103 | }; |
| 104 | |
| 105 | channel@83 { |
| 106 | reg = <ADC5_VPH_PWR>; |
| 107 | qcom,pre-scaling = <1 3>; |
| 108 | label = "vph_pwr"; |
| 109 | }; |
| 110 | |
| 111 | channel@85 { |
| 112 | reg = <ADC5_VCOIN>; |
| 113 | qcom,pre-scaling = <1 3>; |
| 114 | label = "vcoin"; |
| 115 | }; |
| 116 | |
| 117 | channel@4c { |
| 118 | reg = <ADC5_XO_THERM_100K_PU>; |
| 119 | qcom,pre-scaling = <1 1>; |
| 120 | qcom,hw-settle-time = <200>; |
| 121 | qcom,ratiometric; |
| 122 | label = "xo_therm"; |
| 123 | }; |
| 124 | }; |
| 125 | |
| 126 | pm6125_adc_tm: adc-tm@3500 { |
| 127 | compatible = "qcom,spmi-adc-tm5"; |
| 128 | reg = <0x3500>; |
| 129 | interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; |
| 130 | #address-cells = <1>; |
| 131 | #size-cells = <0>; |
| 132 | #thermal-sensor-cells = <1>; |
| 133 | status = "disabled"; |
| 134 | }; |
| 135 | |
| 136 | pm6125_rtc: rtc@6000 { |
| 137 | compatible = "qcom,pm8941-rtc"; |
| 138 | reg = <0x6000>, <0x6100>; |
| 139 | reg-names = "rtc", "alarm"; |
| 140 | interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; |
| 141 | status = "disabled"; |
| 142 | }; |
| 143 | |
| 144 | pm6125_gpios: gpio@c000 { |
| 145 | compatible = "qcom,pm6125-gpio", "qcom,spmi-gpio"; |
| 146 | reg = <0xc000>; |
| 147 | gpio-controller; |
| 148 | gpio-ranges = <&pm6125_gpios 0 0 9>; |
| 149 | #gpio-cells = <2>; |
| 150 | interrupt-controller; |
| 151 | #interrupt-cells = <2>; |
| 152 | }; |
| 153 | }; |
| 154 | |
| 155 | pmic@1 { |
| 156 | compatible = "qcom,pm6125", "qcom,spmi-pmic"; |
| 157 | reg = <0x1 SPMI_USID>; |
| 158 | }; |
| 159 | }; |