| Chunhe Lan | 8e4f3ff | 2014-04-14 18:42:06 +0800 | [diff] [blame] | 1 | /* |
| 2 | * Copyright 2014 Freescale Semiconductor, Inc. |
| 3 | * |
| 4 | * SPDX-License-Identifier: GPL-2.0+ |
| 5 | */ |
| 6 | |
| 7 | #include <common.h> |
| 8 | #include <i2c.h> |
| 9 | #include <hwconfig.h> |
| 10 | #include <asm/mmu.h> |
| 11 | #include <fsl_ddr_sdram.h> |
| 12 | #include <fsl_ddr_dimm_params.h> |
| 13 | #include <asm/fsl_law.h> |
| 14 | #include "ddr.h" |
| 15 | |
| 16 | DECLARE_GLOBAL_DATA_PTR; |
| 17 | |
| 18 | void fsl_ddr_board_options(memctl_options_t *popts, |
| 19 | dimm_params_t *pdimm, |
| 20 | unsigned int ctrl_num) |
| 21 | { |
| 22 | const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; |
| 23 | ulong ddr_freq; |
| 24 | |
| 25 | if (ctrl_num > 2) { |
| 26 | printf("Not supported controller number %d\n", ctrl_num); |
| 27 | return; |
| 28 | } |
| 29 | if (!pdimm->n_ranks) |
| 30 | return; |
| 31 | |
| 32 | /* |
| 33 | * we use identical timing for all slots. If needed, change the code |
| 34 | * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num]; |
| 35 | */ |
| 36 | if (popts->registered_dimm_en) |
| 37 | pbsp = rdimms[0]; |
| 38 | else |
| 39 | pbsp = udimms[0]; |
| 40 | |
| 41 | |
| 42 | /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr |
| 43 | * freqency and n_banks specified in board_specific_parameters table. |
| 44 | */ |
| 45 | ddr_freq = get_ddr_freq(0) / 1000000; |
| 46 | while (pbsp->datarate_mhz_high) { |
| 47 | if (pbsp->n_ranks == pdimm->n_ranks && |
| 48 | (pdimm->rank_density >> 30) >= pbsp->rank_gb) { |
| 49 | if (ddr_freq <= pbsp->datarate_mhz_high) { |
| 50 | popts->clk_adjust = pbsp->clk_adjust; |
| 51 | popts->wrlvl_start = pbsp->wrlvl_start; |
| 52 | popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; |
| 53 | popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; |
| 54 | goto found; |
| 55 | } |
| 56 | pbsp_highest = pbsp; |
| 57 | } |
| 58 | pbsp++; |
| 59 | } |
| 60 | |
| 61 | if (pbsp_highest) { |
| 62 | printf("Error: board specific timing not found for data\n" |
| 63 | "rate %lu MT/s\n" |
| 64 | "Trying to use the highest speed (%u) parameters\n", |
| 65 | ddr_freq, pbsp_highest->datarate_mhz_high); |
| 66 | popts->clk_adjust = pbsp_highest->clk_adjust; |
| 67 | popts->wrlvl_start = pbsp_highest->wrlvl_start; |
| 68 | popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; |
| 69 | popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; |
| 70 | } else { |
| 71 | panic("DIMM is not supported by this board"); |
| 72 | } |
| 73 | found: |
| 74 | debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n" |
| 75 | "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x,\n" |
| 76 | "wrlvl_ctrl_3 0x%x\n", |
| 77 | pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb, |
| 78 | pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2, |
| 79 | pbsp->wrlvl_ctl_3); |
| 80 | |
| 81 | /* |
| 82 | * Factors to consider for half-strength driver enable: |
| 83 | * - number of DIMMs installed |
| 84 | */ |
| 85 | popts->half_strength_driver_enable = 0; |
| 86 | /* |
| 87 | * Write leveling override |
| 88 | */ |
| 89 | popts->wrlvl_override = 1; |
| 90 | popts->wrlvl_sample = 0xf; |
| 91 | |
| 92 | /* |
| 93 | * Rtt and Rtt_WR override |
| 94 | */ |
| 95 | popts->rtt_override = 0; |
| 96 | |
| 97 | /* Enable ZQ calibration */ |
| 98 | popts->zq_en = 1; |
| 99 | |
| 100 | /* DHC_EN =1, ODT = 75 Ohm */ |
| 101 | popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); |
| 102 | popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); |
| 103 | } |
| 104 | |
| 105 | phys_size_t initdram(int board_type) |
| 106 | { |
| 107 | phys_size_t dram_size; |
| 108 | |
| 109 | puts("Initializing....using SPD\n"); |
| 110 | |
| 111 | dram_size = fsl_ddr_sdram(); |
| 112 | |
| 113 | dram_size = setup_ddr_tlbs(dram_size / 0x100000); |
| 114 | dram_size *= 0x100000; |
| 115 | |
| 116 | puts(" DDR: "); |
| 117 | return dram_size; |
| 118 | } |