| Haiying Wang | 3202f16 | 2006-05-26 10:24:48 -0500 | [diff] [blame] | 1 | Freescale MPC8641HPCN board |
| 2 | =========================== |
| 3 | |
| 4 | Created 05/24/2006 Haiying Wang |
| 5 | ------------------------------- |
| 6 | |
| 7 | 1. Building U-Boot |
| 8 | ------------------ |
| 9 | The 86xx HPCN code base is known to compile using: |
| 10 | Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3 |
| 11 | |
| 12 | $ make MPC8641HPCN_config |
| 13 | Configuring for MPC8641HPCN board... |
| 14 | |
| 15 | $ make |
| 16 | |
| 17 | |
| 18 | 2. Switch and Jumper Setting |
| 19 | ---------------------------- |
| 20 | Jumpers: |
| 21 | J14 Pins 1-2 (near plcc32 socket) |
| 22 | |
| 23 | Switches: |
| 24 | SW1(1-5) = 01100 CFG_COREPLL = 01000 :: CORE = 2:1 |
| 25 | 01100 :: CORE = 2.5:1 |
| 26 | 10000 :: CORE = 3:1 |
| 27 | 11100 :: CORE = 3.5:1 |
| 28 | 10100 :: CORE = 4:1 |
| 29 | 01110 :: CORE = 4.5:1 |
| 30 | SW1(6-8) = 001 CFG_SYSCLK = 000 :: SYSCLK = 33MHz |
| 31 | 001 :: SYSCLK = 40MHz |
| 32 | |
| Jon Loeliger | 5ecfab2 | 2006-10-10 17:06:53 -0500 | [diff] [blame^] | 33 | SW2(1-4) = 1100 CFG_CCBPLL = 0010 :: 2X |
| Haiying Wang | 3202f16 | 2006-05-26 10:24:48 -0500 | [diff] [blame] | 34 | 0100 :: 4X |
| 35 | 0110 :: 6X |
| 36 | 1000 :: 8X |
| 37 | 1010 :: 10X |
| 38 | 1100 :: 12X |
| 39 | 1110 :: 14X |
| 40 | 0000 :: 16X |
| 41 | SW2(5-8) = 1110 CFG_BOOTLOC = 1110 :: boot 16-bit localbus |
| 42 | |
| 43 | SW3(1-7) = 0011000 CFG_VID = 0011000 :: VCORE = 1.2V |
| 44 | 0100000 :: VCORE = 1.11V |
| 45 | SW3(8) = 0 VCC_PLAT = 0 :: VCC_PLAT = 1.2V |
| 46 | 1 :: VCC_PLAT = 1.0V |
| 47 | |
| 48 | SW4(1-2) = 11 CFG_HOSTMODE = 11 :: both prots host/root |
| 49 | SW4(3-4) = 11 CFG_BOOTSEQ = 11 :: no boot seq |
| 50 | SW4(5-8) = 0011 CFG_IOPORT = 0011 :: both PEX |
| 51 | |
| 52 | SW5(1) = 1 CFG_FLASHMAP = 1 :: boot from flash |
| 53 | 0 :: boot from PromJet |
| 54 | SW5(2) = 1 CFG_FLASHBANK = 1 :: swap upper/lower |
| 55 | halves (virtual banks) |
| 56 | 0 :: normal |
| 57 | SW5(3) = 0 CFG_FLASHWP = 0 :: not protected |
| 58 | SW5(4) = 0 CFG_PORTDIV = 1 :: 2:1 for PD4 |
| 59 | 1:1 for PD6 |
| 60 | SW5(5-6) = 11 CFG_PIXISOPT = 11 :: s/w determined |
| 61 | SW5(7-8) = 11 CFG_LADOPT = 11 :: s/w determined |
| 62 | |
| 63 | SW6(1) = 1 CFG_CPUBOOT = 1 :: no boot holdoff |
| 64 | SW6(2) = 1 CFG_BOOTADDR = 1 :: no traslation |
| 65 | SW6(3-5) = 000 CFG_REFCLKSEL = 000 :: 100MHZ |
| 66 | SW6(6) = 1 CFG_SERROM_ADDR= 1 :: |
| 67 | SW6(7) = 1 CFG_MEMDEBUG = 1 :: |
| 68 | SW6(8) = 1 CFG_DDRDEBUG = 1 :: |
| 69 | |
| 70 | SW8(1) = 1 ACZ_SYNC = 1 :: 48MHz on TP49 |
| 71 | SW8(2) = 1 ACB_SYNC = 1 :: THRMTRIP disabled |
| 72 | SW8(3) = 1 ACZ_SDOUT = 1 :: p4 mode |
| 73 | SW8(4) = 1 ACB_SDOUT = 1 :: PATA freq. = 133MHz |
| 74 | SW8(5) = 0 SUSLED = 0 :: SouthBridge Mode |
| 75 | SW8(6) = 0 SPREAD = 0 :: REFCLK SSCG Disabled |
| 76 | SW8(7) = 1 ACPWR = 1 :: non-battery |
| 77 | SW8(8) = 0 CFG_IDWP = 0 :: write enable |
| 78 | |
| 79 | |
| 80 | 3. Flash U-Boot |
| 81 | --------------- |
| 82 | The flash range 0xFF800000 to 0xFFFFFFFF can be divided into 2 halves. |
| 83 | It is possible to use either half to boot using u-boot. Switch 5 bit 2 |
| 84 | is used for this purpose. |
| 85 | |
| 86 | 0xFF800000 to 0xFFBFFFFF - 4MB |
| 87 | 0xFFC00000 to 0xFFFFFFFF - 4MB |
| 88 | When this bit is 0, U-Boot is at 0xFFF00000. |
| 89 | When this bit is 1, U-Boot is at 0xFFB00000. |
| 90 | |
| 91 | Use the above mentioned flash commands to program the other half, and |
| 92 | use switch 5, bit 2 to alternate between the halves. Note: The booting |
| 93 | version of U-Boot will always be at 0xFFF00000. |
| 94 | |
| 95 | To Flash U-Boot into the booting bank (0xFFC00000 - 0xFFFFFFFF): |
| 96 | |
| 97 | tftp 1000000 u-boot.bin |
| 98 | protect off all |
| 99 | erase fff00000 ffffffff |
| 100 | cp.b 1000000 fff00100 80000 |
| 101 | |
| 102 | To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF): |
| 103 | |
| 104 | tftp 1000000 u-boot.bin |
| 105 | erase ffb00000 ffbfffff |
| 106 | cp.b 1000000 ffb00100 80000 |
| 107 | |
| 108 | |
| 109 | 4. Memory Map |
| 110 | ------------- |
| 111 | |
| Jon Loeliger | 5ecfab2 | 2006-10-10 17:06:53 -0500 | [diff] [blame^] | 112 | Memory Range Device Size |
| Haiying Wang | 3202f16 | 2006-05-26 10:24:48 -0500 | [diff] [blame] | 113 | ------------ ------ ---- |
| 114 | 0x0000_0000 0x7fff_ffff DDR 2G |
| 115 | 0x8000_0000 0x9fff_ffff PCI1/PEX1 MEM 512M |
| 116 | 0xa000_0000 0xafff_ffff PCI2/PEX2 MEM 512M |
| 117 | 0xf800_0000 0xf80f_ffff CCSR 1M |
| 118 | 0xf810_0000 0xf81f_ffff PIXIS 1M |
| 119 | 0xf840_0000 0xf840_3fff Stack space 32K |
| Haiying Wang | d8082c1 | 2006-07-28 12:41:41 -0400 | [diff] [blame] | 120 | 0xe200_0000 0xe2ff_ffff PCI1/PEX1 IO 16M |
| 121 | 0xe300_0000 0xe3ff_ffff PCI2/PEX2 IO 16M |
| Haiying Wang | 3202f16 | 2006-05-26 10:24:48 -0500 | [diff] [blame] | 122 | 0xfe00_0000 0xfeff_ffff Flash(alternate)16M |
| 123 | 0xff00_0000 0xffff_ffff Flash(boot bank)16M |