Gitiles
Code Review Sign In
git01.mediatek.com / filogic / uboot / 5e017409383c3677e376fa7a359d2c71c0db31b8 / . / dts / upstream / Bindings / pinctrl / realtek,rtd1315e-pinctrl.yaml
blob: fc6c65fea73bb7389691a33b9ed7d4cc8c36da36 [file] [log] [blame]
Tom Rini53633a82024-02-29 12:33:36 -0500[diff] [blame]1# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
2# Copyright 2023 Realtek Semiconductor Corporation
3%YAML 1.2
4---
5$id: http://devicetree.org/schemas/pinctrl/realtek,rtd1315e-pinctrl.yaml#
6$schema: http://devicetree.org/meta-schemas/core.yaml#
7
8title: Realtek DHC RTD1315E Pin Controller
9
10maintainers:
11 - TY Chang <tychang@realtek.com>
12
13description:
14 The Realtek DHC RTD1315E is a high-definition media processor SoC. The
15 RTD1315E pin controller is used to control pin function, pull up/down
16 resistor, drive strength, schmitt trigger and power source.
17
18properties:
19 compatible:
20 const: realtek,rtd1315e-pinctrl
21
22 reg:
23 maxItems: 1
24
25patternProperties:
26 '-pins$':
27 type: object
28 allOf:
29 - $ref: pincfg-node.yaml#
30 - $ref: pinmux-node.yaml#
31
32 properties:
33 pins:
34 items:
35 enum: [ gpio_0, gpio_1, emmc_rst_n, emmc_dd_sb, emmc_clk, emmc_cmd,
36 gpio_6, gpio_7, gpio_8, gpio_9, gpio_10, gpio_11, gpio_12,
37 gpio_13, gpio_14, gpio_15, gpio_16, gpio_17, gpio_18, gpio_19,
38 gpio_20, emmc_data_0, emmc_data_1, emmc_data_2, usb_cc2, gpio_25,
39 gpio_26, gpio_27, gpio_28, gpio_29, gpio_30, gpio_31, gpio_32,
40 gpio_33, gpio_34, gpio_35, hif_data, hif_en, hif_rdy, hif_clk,
41 gpio_dummy_40, gpio_dummy_41, gpio_dummy_42, gpio_dummy_43,
42 gpio_dummy_44, gpio_dummy_45, gpio_46, gpio_47, gpio_48, gpio_49,
43 gpio_50, usb_cc1, emmc_data_3, emmc_data_4, ir_rx, ur0_rx, ur0_tx,
44 gpio_57, gpio_58, gpio_59, gpio_60, gpio_61, gpio_62, gpio_dummy_63,
45 gpio_dummy_64, gpio_dummy_65, gpio_66, gpio_67, gpio_68, gpio_69,
46 gpio_70, gpio_71, gpio_72, gpio_dummy_73, emmc_data_5, emmc_data_6,
47 emmc_data_7, gpio_dummy_77, gpio_78, gpio_79, gpio_80, gpio_81,
48 ur2_loc, gspi_loc, hi_width, sf_en, arm_trace_dbg_en,
49 ejtag_aucpu_loc, ejtag_acpu_loc, ejtag_vcpu_loc, ejtag_scpu_loc,
50 dmic_loc, vtc_dmic_loc, vtc_tdm_loc, vtc_i2si_loc, tdm_ai_loc,
51 ai_loc, spdif_loc, hif_en_loc, scan_switch, wd_rset, boot_sel,
52 reset_n, testmode ]
53
54 function:
55 enum: [ gpio, nf, emmc, ao, gspi_loc0, gspi_loc1, uart0, uart1,
56 uart2_loc0, uart2_loc1, i2c0, i2c1, i2c4, i2c5, pcie1,
57 etn_led, etn_phy, spi, pwm0_loc0, pwm0_loc1, pwm1_loc0,
58 pwm1_loc1, pwm2_loc0, pwm2_loc1, pwm3_loc0, pwm3_loc1,
59 spdif_optical_loc0, spdif_optical_loc1, usb_cc1, usb_cc2,
60 sd, dmic_loc0, dmic_loc1, ai_loc0, ai_loc1, tdm_ai_loc0,
61 tdm_ai_loc1, hi_loc0, hi_m, vtc_i2so, vtc_i2si_loc0,
62 vtc_i2si_loc1, vtc_dmic_loc0, vtc_dmic_loc1, vtc_tdm_loc0,
63 vtc_tdm_loc1, dc_fan, pll_test_loc0, pll_test_loc1,
64 ir_rx, uart2_disable, gspi_disable, hi_width_disable,
65 hi_width_1bit, sf_disable, sf_enable, scpu_ejtag_loc0,
66 scpu_ejtag_loc1, scpu_ejtag_loc2, scpu_ejtag_loc3,
67 acpu_ejtag_loc0, acpu_ejtag_loc1, acpu_ejtag_loc2,
68 vcpu_ejtag_loc0, vcpu_ejtag_loc1, vcpu_ejtag_loc2,
69 aucpu_ejtag_loc0, aucpu_ejtag_loc1, aucpu_ejtag_loc2,
70 gpu_ejtag, iso_tristate, dbg_out0, dbg_out1, standby_dbg,
71 spdif, arm_trace_debug_disable, arm_trace_debug_enable,
72 aucpu_ejtag_disable, acpu_ejtag_disable, vcpu_ejtag_disable,
73 scpu_ejtag_disable, vtc_dmic_loc_disable, vtc_tdm_disable,
74 vtc_i2si_disable, tdm_ai_disable, ai_disable, spdif_disable,
75 hif_disable, hif_enable, test_loop, pmic_pwrup ]
76
77 drive-strength:
78 enum: [4, 8]
79
80 bias-pull-down: true
81
82 bias-pull-up: true
83
84 bias-disable: true
85
86 input-schmitt-enable: true
87
88 input-schmitt-disable: true
89
90 drive-push-pull: true
91
92 power-source:
93 description: |
94 Valid arguments are described as below:
95 0: power supply of 1.8V
96 1: power supply of 3.3V
97 enum: [0, 1]
98
99 realtek,drive-strength-p:
100 description: |
101 Some of pins can be driven using the P-MOS and N-MOS transistor to
102 achieve finer adjustments. The block-diagram representation is as
103 follows:
104 VDD
105 |
106 ||--+
107 +-----o|| P-MOS-FET
108 | ||--+
109 IN --+ +----- out
110 | ||--+
111 +------|| N-MOS-FET
112 ||--+
113 |
114 GND
115 The driving strength of the P-MOS/N-MOS transistors impacts the
116 waveform's rise/fall times. Greater driving strength results in
117 shorter rise/fall times. Each P-MOS and N-MOS transistor offers
118 8 configurable levels (0 to 7), with higher values indicating
119 greater driving strength, contributing to achieving the desired
120 speed.
121
122 The realtek,drive-strength-p is used to control the driving strength
123 of the P-MOS output.
124 $ref: /schemas/types.yaml#/definitions/uint32
125 minimum: 0
126 maximum: 7
127
128 realtek,drive-strength-n:
129 description: |
130 Similar to the realtek,drive-strength-p, the realtek,drive-strength-n
131 is used to control the driving strength of the N-MOS output.
132 $ref: /schemas/types.yaml#/definitions/uint32
133 minimum: 0
134 maximum: 7
135
136 realtek,duty-cycle:
137 description: |
138 An integer describing the level to adjust output duty cycle, controlling
139 the proportion of positive and negative waveforms in nanoseconds.
140 Valid arguments are described as below:
141 0: 0ns
142 2: + 0.25ns
143 3: + 0.5ns
144 4: -0.25ns
145 5: -0.5ns
146 $ref: /schemas/types.yaml#/definitions/uint32
147 enum: [ 0, 2, 3, 4, 5 ]
148
149 required:
150 - pins
151
152 additionalProperties: false
153
154required:
155 - compatible
156 - reg
157
158additionalProperties: false
159
160examples:
161 - |
162 pinctrl@4e000 {
163 compatible = "realtek,rtd1315e-pinctrl";
164 reg = <0x4e000 0x130>;
165
166 emmc-hs200-pins {
167 pins = "emmc_clk",
168 "emmc_cmd",
169 "emmc_data_0",
170 "emmc_data_1",
171 "emmc_data_2",
172 "emmc_data_3",
173 "emmc_data_4",
174 "emmc_data_5",
175 "emmc_data_6",
176 "emmc_data_7";
177 function = "emmc";
178 realtek,drive-strength-p = <0x2>;
179 realtek,drive-strength-n = <0x2>;
180 };
181
182 i2c-0-pins {
183 pins = "gpio_12",
184 "gpio_13";
185 function = "i2c0";
186 drive-strength = <4>;
187 };
188 };