arch/arm/Kconfig

menu "ARM architecture"
	depends on ARM

config SYS_ARCH
	default "arm"

config ARM64
	bool
	select PHYS_64BIT
	select SYS_CACHE_SHIFT_6
	imply SPL_SEPARATE_BSS

config ARM64_CRC32
	bool "Enable support for CRC32 instruction"
	depends on ARM64
	default y
	help
	  ARMv8 implements dedicated crc32 instruction for crc32 calculation.
	  This is faster than software crc32 calculation. This instruction may
	  not be present on all ARMv8.0, but is always present on ARMv8.1 and
	  newer.

config COUNTER_FREQUENCY
	int "Timer clock frequency"
	depends on ARM64 || CPU_V7A
	default 8000000 if IMX8 || MX7 || MX6UL || MX6ULL
	default 24000000 if ARCH_SUNXI || ARCH_EXYNOS || ROCKCHIP_RK3128 || \
			ROCKCHIP_RK3288 || ROCKCHIP_RK322X || ROCKCHIP_RK3036
	default 25000000 if ARCH_LX2160A || ARCH_LX2162A || ARCH_LS1088A
	default 100000000 if ARCH_ZYNQMP
	default 0
	help
	  For platforms with ARMv8-A and ARMv7-A which features a system
	  counter, those platforms needs software to program the counter
	  frequency. Setup time clock frequency for certain platform.
	  0 means no need to configure the system counter frequency.
	  For platforms needs the frequency set in U-Boot with a
	  pre-defined value, should have the macro defined as a non-zero value.

config POSITION_INDEPENDENT
	bool "Generate position-independent pre-relocation code"
	depends on ARM64 || CPU_V7A
	help
	  U-Boot expects to be linked to a specific hard-coded address, and to
	  be loaded to and run from that address. This option lifts that
	  restriction, thus allowing the code to be loaded to and executed from
	  almost any 4K aligned address. This logic relies on the relocation
	  information that is embedded in the binary to support U-Boot
	  relocating itself to the top-of-RAM later during execution.

config INIT_SP_RELATIVE
	bool "Specify the early stack pointer relative to the .bss section"
	depends on ARM64
	default n if ARCH_QEMU
	default y if POSITION_INDEPENDENT
	help
	  U-Boot typically uses a hard-coded value for the stack pointer
	  before relocation. Enable this option to instead calculate the
	  initial SP at run-time. This is useful to avoid hard-coding addresses
	  into U-Boot, so that it can be loaded and executed at arbitrary
	  addresses and thus avoid using arbitrary addresses at runtime.

	  If this option is enabled, the early stack pointer is set to
	  &_bss_start with a offset value added. The offset is specified by
	  SYS_INIT_SP_BSS_OFFSET.

config SYS_INIT_SP_BSS_OFFSET
	int "Early stack offset from the .bss base address"
	depends on ARM64
	depends on INIT_SP_RELATIVE
	default 524288
	help
	  This option's value is the offset added to &_bss_start in order to
	  calculate the stack pointer. This offset should be large enough so
	  that the early malloc region, global data (gd), and early stack usage
	  do not overlap any appended DTB.

config SPL_SYS_NO_VECTOR_TABLE
	depends on SPL
	bool

config LINUX_KERNEL_IMAGE_HEADER
	depends on ARM64
	bool
	help
	  Place a Linux kernel image header at the start of the U-Boot binary.
	  The format of the header is described in the Linux kernel source at
	  Documentation/arm64/booting.txt. This feature is useful since the
	  image header reports the amount of memory (BSS and similar) that
	  U-Boot needs to use, but which isn't part of the binary.

config LNX_KRNL_IMG_TEXT_OFFSET_BASE
	depends on LINUX_KERNEL_IMAGE_HEADER
	hex
	help
	  The value subtracted from CONFIG_TEXT_BASE to calculate the
	  TEXT_OFFSET value written to the Linux kernel image header.

config GICV2
	bool

config GICV3
	bool

config GIC_V3_ITS
	bool "ARM GICV3 ITS"
	select IRQ
	help
	  ARM GICV3 Interrupt translation service (ITS).
	  Basic support for programming locality specific peripheral
	  interrupts (LPI) configuration tables and enable LPI tables.
	  LPI configuration table can be used by u-boot or Linux.
	  ARM GICV3 has limitation, once the LPI table is enabled, LPI
	  configuration table can not be re-programmed, unless GICV3 reset.

config STATIC_RELA
	bool
	default y if ARM64

config DMA_ADDR_T_64BIT
	bool
	default y if ARM64

config HAS_VBAR
	bool

config HAS_THUMB2
	bool

config GPIO_EXTRA_HEADER
	bool

# Used for compatibility with asm files copied from the kernel
config ARM_ASM_UNIFIED
	bool
	default y

# Used for compatibility with asm files copied from the kernel
config THUMB2_KERNEL
	bool

config SYS_ICACHE_OFF
	bool "Do not enable icache"
	help
	  Do not enable instruction cache in U-Boot.

config SPL_SYS_ICACHE_OFF
	bool "Do not enable icache in SPL"
	depends on SPL
	default SYS_ICACHE_OFF
	help
	  Do not enable instruction cache in SPL.

config SYS_DCACHE_OFF
	bool "Do not enable dcache"
	help
	  Do not enable data cache in U-Boot.

config SPL_SYS_DCACHE_OFF
	bool "Do not enable dcache in SPL"
	depends on SPL
	default SYS_DCACHE_OFF
	help
	  Do not enable data cache in SPL.

config SYS_ARM_CACHE_CP15
	bool "CP15 based cache enabling support"
	help
	  Select this if your processor suports enabling caches by using
	  CP15 registers.

config SYS_ARM_MMU
	bool "MMU-based Paged Memory Management Support"
	select SYS_ARM_CACHE_CP15
	help
	  Select if you want MMU-based virtualised addressing space
	  support via paged memory management.

config SYS_ARM_MPU
	bool 'Use the ARM v7 PMSA Compliant MPU'
	help
	  Some ARM systems without an MMU have instead a Memory Protection
	  Unit (MPU) that defines the type and permissions for regions of
	  memory.
	  If your CPU has an MPU then you should choose 'y' here unless you
	  know that you do not want to use the MPU.

# If set, the workarounds for these ARM errata are applied early during U-Boot
# startup. Note that in general these options force the workarounds to be
# applied; no CPU-type/version detection exists, unlike the similar options in
# the Linux kernel. Do not set these options unless they apply!  Also note that
# the following can be machine-specific errata. These do have ability to
# provide rudimentary version and machine-specific checks, but expect no
# product checks:
# CONFIG_ARM_ERRATA_430973
# CONFIG_ARM_ERRATA_454179
# CONFIG_ARM_ERRATA_621766
# CONFIG_ARM_ERRATA_798870
# CONFIG_ARM_ERRATA_801819
# CONFIG_ARM_CORTEX_A8_CVE_2017_5715
# CONFIG_ARM_CORTEX_A15_CVE_2017_5715

config ARM_ERRATA_430973
	bool

config ARM_ERRATA_454179
	bool

config ARM_ERRATA_621766
	bool

config ARM_ERRATA_716044
	bool

config ARM_ERRATA_725233
	bool

config ARM_ERRATA_742230
	bool

config ARM_ERRATA_743622
	bool

config ARM_ERRATA_751472
	bool

config ARM_ERRATA_761320
	bool

config ARM_ERRATA_773022
	bool

config ARM_ERRATA_774769
	bool

config ARM_ERRATA_794072
	bool

config ARM_ERRATA_798870
	bool

config ARM_ERRATA_801819
	bool

config ARM_ERRATA_826974
	bool

config ARM_ERRATA_828024
	bool

config ARM_ERRATA_829520
	bool

config ARM_ERRATA_833069
	bool

config ARM_ERRATA_833471
	bool

config ARM_ERRATA_845369
	bool

config ARM_ERRATA_852421
	bool

config ARM_ERRATA_852423
	bool

config ARM_ERRATA_855873
	bool

config ARM_CORTEX_A8_CVE_2017_5715
	bool

config ARM_CORTEX_A15_CVE_2017_5715
	bool

config CPU_ARM720T
	bool
	select SYS_CACHE_SHIFT_5
	imply SYS_ARM_MMU

config CPU_ARM920T
	bool
	select SYS_CACHE_SHIFT_5
	imply SYS_ARM_MMU

config CPU_ARM926EJS
	bool
	select SYS_CACHE_SHIFT_5
	imply SYS_ARM_MMU
	imply SPL_SEPARATE_BSS

config CPU_ARM946ES
	bool
	select SYS_CACHE_SHIFT_5
	imply SYS_ARM_MMU

config CPU_ARM1136
	bool
	select SYS_CACHE_SHIFT_5
	imply SYS_ARM_MMU
	imply SPL_SEPARATE_BSS

config CPU_ARM1176
	bool
	select HAS_VBAR
	select SYS_CACHE_SHIFT_5
	imply SYS_ARM_MMU

config CPU_V7A
	bool
	select HAS_THUMB2
	select HAS_VBAR
	select SYS_CACHE_SHIFT_6
	imply SYS_ARM_MMU

config CPU_V7M
	bool
	select HAS_THUMB2
	select SYS_ARM_MPU
	select SYS_CACHE_SHIFT_5
	select SYS_THUMB_BUILD
	select THUMB2_KERNEL

config CPU_V7R
	bool
	select HAS_THUMB2
	select SYS_ARM_CACHE_CP15
	select SYS_ARM_MPU
	select SYS_CACHE_SHIFT_6

config SYS_CPU
	default "arm720t" if CPU_ARM720T
	default "arm920t" if CPU_ARM920T
	default "arm926ejs" if CPU_ARM926EJS
	default "arm946es" if CPU_ARM946ES
	default "arm1136" if CPU_ARM1136
	default "arm1176" if CPU_ARM1176
	default "armv7" if CPU_V7A
	default "armv7" if CPU_V7R
	default "armv7m" if CPU_V7M
	default "armv8" if ARM64

config SYS_ARM_ARCH
	int
	default 4 if CPU_ARM720T
	default 4 if CPU_ARM920T
	default 5 if CPU_ARM926EJS
	default 5 if CPU_ARM946ES
	default 6 if CPU_ARM1136
	default 6 if CPU_ARM1176
	default 7 if CPU_V7A
	default 7 if CPU_V7M
	default 7 if CPU_V7R
	default 8 if ARM64

choice
	prompt "Select the ARM data write cache policy"
	default SYS_ARM_CACHE_WRITETHROUGH if TARGET_BCMCYGNUS || RZA1
	default SYS_ARM_CACHE_WRITEBACK

config SYS_ARM_CACHE_WRITEBACK
	bool "Write-back (WB)"
	help
	  A write updates the cache only and marks the cache line as dirty.
	  External memory is updated only when the line is evicted or explicitly
	  cleaned.

config SYS_ARM_CACHE_WRITETHROUGH
	bool "Write-through (WT)"
	help
	  A write updates both the cache and the external memory system.
	  This does not mark the cache line as dirty.

config SYS_ARM_CACHE_WRITEALLOC
	bool "Write allocation (WA)"
	help
	  A cache line is allocated on a write miss. This means that executing a
	  store instruction on the processor might cause a burst read to occur.
	  There is a linefill to obtain the data for the cache line, before the
	  write is performed.
endchoice

config ARCH_VERY_EARLY_INIT
	bool

config SPL_ARCH_VERY_EARLY_INIT
	bool

config ARCH_CPU_INIT
	bool "Enable ARCH_CPU_INIT"
	help
	  Some architectures require a call to arch_cpu_init().
	  Say Y here to enable it

config SYS_ARCH_TIMER
	bool "ARM Generic Timer support"
	depends on CPU_V7A || ARM64
	default y if ARM64
	help
	  The ARM Generic Timer (aka arch-timer) provides an architected
	  interface to a timer source on an SoC.
	  It is mandatory for ARMv8 implementation and widely available
	  on ARMv7 systems.

config ARM_SMCCC
	bool "Support for ARM SMC Calling Convention (SMCCC)"
	depends on CPU_V7A || ARM64
	select ARM_PSCI_FW
	help
	  Say Y here if you want to enable ARM SMC Calling Convention.
	  This should be enabled if U-Boot needs to communicate with system
	  firmware (for example, PSCI) according to SMCCC.

config SYS_THUMB_BUILD
	bool "Build U-Boot using the Thumb instruction set"
	depends on !ARM64
	help
	   Use this flag to build U-Boot using the Thumb instruction set for
	   ARM architectures. Thumb instruction set provides better code
	   density. For ARM architectures that support Thumb2 this flag will
	   result in Thumb2 code generated by GCC.

config SPL_SYS_THUMB_BUILD
	bool "Build SPL using the Thumb instruction set"
	default y if SYS_THUMB_BUILD
	depends on !ARM64 && SPL
	help
	   Use this flag to build SPL using the Thumb instruction set for
	   ARM architectures. Thumb instruction set provides better code
	   density. For ARM architectures that support Thumb2 this flag will
	   result in Thumb2 code generated by GCC.

config TPL_SYS_THUMB_BUILD
	bool "Build TPL using the Thumb instruction set"
	default y if SYS_THUMB_BUILD
	depends on TPL && !ARM64
	help
	   Use this flag to build TPL using the Thumb instruction set for
	   ARM architectures. Thumb instruction set provides better code
	   density. For ARM architectures that support Thumb2 this flag will
	   result in Thumb2 code generated by GCC.

config SYS_L2_PL310
	bool "ARM PL310 L2 cache controller"
	help
	  Enable support for ARM PL310 L2 cache controller in U-Boot

config SPL_SYS_L2_PL310
	bool "ARM PL310 L2 cache controller in SPL"
	help
	  Enable support for ARM PL310 L2 cache controller in SPL

config SYS_L2CACHE_OFF
	bool "L2cache off"
	help
	  If SoC does not support L2CACHE or one does not want to enable
	  L2CACHE, choose this option.

config ENABLE_ARM_SOC_BOOT0_HOOK
	bool "prepare BOOT0 header"
	help
	  If the SoC's BOOT0 requires a header area filled with (magic)
	  values, then choose this option, and create a file included as
	  <asm/arch/boot0.h> which contains the required assembler code.

config USE_ARCH_MEMCPY
	bool "Use an assembly optimized implementation of memcpy"
	default y if !ARM64
	depends on !ARM64 || (ARM64 && (GCC_VERSION >= 90400))
	help
	  Enable the generation of an optimized version of memcpy.
	  Such an implementation may be faster under some conditions
	  but may increase the binary size.

config SPL_USE_ARCH_MEMCPY
	bool "Use an assembly optimized implementation of memcpy for SPL"
	default y if USE_ARCH_MEMCPY
	depends on SPL
	help
	  Enable the generation of an optimized version of memcpy.
	  Such an implementation may be faster under some conditions
	  but may increase the binary size.

config TPL_USE_ARCH_MEMCPY
	bool "Use an assembly optimized implementation of memcpy for TPL"
	default y if USE_ARCH_MEMCPY
	depends on TPL
	help
	  Enable the generation of an optimized version of memcpy.
	  Such an implementation may be faster under some conditions
	  but may increase the binary size.

config USE_ARCH_MEMMOVE
	bool "Use an assembly optimized implementation of memmove" if !ARM64
	default USE_ARCH_MEMCPY if ARM64
	depends on ARM64
	help
	  Enable the generation of an optimized version of memmove.
	  Such an implementation may be faster under some conditions
	  but may increase the binary size.

config SPL_USE_ARCH_MEMMOVE
	bool "Use an assembly optimized implementation of memmove for SPL" if !ARM64
	default SPL_USE_ARCH_MEMCPY if ARM64
	depends on SPL && ARM64
	help
	  Enable the generation of an optimized version of memmove.
	  Such an implementation may be faster under some conditions
	  but may increase the binary size.

config TPL_USE_ARCH_MEMMOVE
	bool "Use an assembly optimized implementation of memmove for TPL" if !ARM64
	default TPL_USE_ARCH_MEMCPY if ARM64
	depends on TPL && ARM64
	help
	  Enable the generation of an optimized version of memmove.
	  Such an implementation may be faster under some conditions
	  but may increase the binary size.

config USE_ARCH_MEMSET
	bool "Use an assembly optimized implementation of memset"
	default y if !ARM64
	depends on !ARM64 || (ARM64 && (GCC_VERSION >= 90400))
	help
	  Enable the generation of an optimized version of memset.
	  Such an implementation may be faster under some conditions
	  but may increase the binary size.

config SPL_USE_ARCH_MEMSET
	bool "Use an assembly optimized implementation of memset for SPL"
	default y if USE_ARCH_MEMSET
	depends on SPL
	help
	  Enable the generation of an optimized version of memset.
	  Such an implementation may be faster under some conditions
	  but may increase the binary size.

config TPL_USE_ARCH_MEMSET
	bool "Use an assembly optimized implementation of memset for TPL"
	default y if USE_ARCH_MEMSET
	depends on TPL
	help
	  Enable the generation of an optimized version of memset.
	  Such an implementation may be faster under some conditions
	  but may increase the binary size.

config ARM64_SUPPORT_AARCH32
	bool "ARM64 system support AArch32 execution state"
	depends on ARM64
	default y if !TARGET_THUNDERX_88XX
	help
	  This ARM64 system supports AArch32 execution state.

config IPROC
	bool

config S5P
	def_bool y if ARCH_EXYNOS || ARCH_S5PC1XX

choice
	prompt "Target select"
	default TARGET_HIKEY

config ARCH_AT91
	bool "Atmel AT91"
	select GPIO_EXTRA_HEADER
	select SPL_BOARD_INIT if SPL && !TARGET_SMARTWEB
	select SPL_SEPARATE_BSS if SPL

config ARCH_DAVINCI
	bool "TI DaVinci"
	select CPU_ARM926EJS
	select GPIO_EXTRA_HEADER
	select SPL_DM_SPI if SPL
	imply CMD_SAVES
	help
	  Support for TI's DaVinci platform.

config ARCH_KIRKWOOD
	bool "Marvell Kirkwood"
	select ARCH_MISC_INIT
	select BOARD_EARLY_INIT_F
	select CPU_ARM926EJS
	select GPIO_EXTRA_HEADER
	select TIMER

config ARCH_MVEBU
	bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)"
	select DM
	select DM_SERIAL
	select DM_SPI
	select DM_SPI_FLASH
	select GPIO_EXTRA_HEADER
	select SPL_DM_SPI if SPL
	select SPL_DM_SPI_FLASH if SPL
	select SPL_TIMER if SPL
	select TIMER if !ARM64
	select OF_CONTROL
	select OF_SEPARATE
	select SPI
	imply CMD_DM

config ARCH_ORION5X
	bool "Marvell Orion"
	select CPU_ARM926EJS
	select GPIO_EXTRA_HEADER
	select SPL_SEPARATE_BSS if SPL
	select TIMER

config TARGET_STV0991
	bool "Support stv0991"
	select CPU_V7A
	select DM
	select DM_SERIAL
	select DM_SPI
	select DM_SPI_FLASH
	select GPIO_EXTRA_HEADER
	select PL01X_SERIAL
	select SPI
	select SPI_FLASH
	imply CMD_DM

config ARCH_BCM283X
	bool "Broadcom BCM283X family"
	select DM
	select DM_GPIO
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	select OF_CONTROL
	select PL01X_SERIAL
	select SERIAL_SEARCH_ALL
	imply CMD_DM
	imply FAT_WRITE

config ARCH_BCMSTB
	bool "Broadcom BCM7XXX family"
	select CPU_V7A
	select DM
	select GPIO_EXTRA_HEADER
	select OF_CONTROL
	imply CMD_DM
	imply OF_HAS_PRIOR_STAGE
	help
	  This enables support for Broadcom ARM-based set-top box
	  chipsets, including the 7445 family of chips.

config ARCH_BCMBCA
	bool "Broadcom broadband chip family"
	select DM
	select OF_CONTROL
	imply CMD_DM

config TARGET_VEXPRESS_CA9X4
	bool "Support vexpress_ca9x4"
	select CPU_V7A
	select PL011_SERIAL

config TARGET_BCMCYGNUS
	bool "Support bcmcygnus"
	select CPU_V7A
	select GPIO_EXTRA_HEADER
	select IPROC
	imply BCM_SF2_ETH
	imply BCM_SF2_ETH_GMAC
	imply CMD_HASH
	imply CRC32_VERIFY
	imply FAT_WRITE
	imply HASH_VERIFY
	imply NETDEVICES

config TARGET_BCMNS2
	bool "Support Broadcom Northstar2"
	select ARM64
	select GPIO_EXTRA_HEADER
	help
	  Support for Broadcom Northstar 2 SoCs.  NS2 is a quad-core 64-bit
	  ARMv8 Cortex-A57 processors targeting a broad range of networking
	  applications.

config TARGET_BCMNS3
	bool "Support Broadcom NS3"
	select ARM64
	select BOARD_LATE_INIT
	help
	  Support for Broadcom Northstar 3 SoCs. NS3 is a octo-core 64-bit
	  ARMv8 Cortex-A72 processors targeting a broad range of networking
	  applications.

config ARCH_EXYNOS
	bool "Samsung EXYNOS"
	select DM
	select DM_GPIO
	select DM_I2C
	select DM_KEYBOARD
	select DM_SERIAL
	select DM_SPI
	select DM_SPI_FLASH
	select SPI
	select GPIO_EXTRA_HEADER
	imply SYS_THUMB_BUILD
	imply CMD_DM
	imply FAT_WRITE

config ARCH_S5PC1XX
	bool "Samsung S5PC1XX"
	select CPU_V7A
	select DM
	select DM_GPIO
	select DM_I2C
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	imply CMD_DM

config ARCH_HIGHBANK
	bool "Calxeda Highbank"
	select CPU_V7A
	select PL01X_SERIAL
	select DM
	select DM_SERIAL
	select OF_CONTROL
	select CLK
	select CLK_CCF
	select AHCI
	select PHYS_64BIT
	select TIMER
	select SP804_TIMER
	imply OF_HAS_PRIOR_STAGE

config ARCH_INTEGRATOR
	bool "ARM Ltd. Integrator family"
	select DM
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	select PL01X_SERIAL
	imply CMD_DM

config ARCH_IPQ40XX
	bool "Qualcomm IPQ40xx SoCs"
	select CPU_V7A
	select DM
	select DM_GPIO
	select DM_SERIAL
	select DM_RESET
	select GPIO_EXTRA_HEADER
	select MSM_SMEM
	select PINCTRL
	select CLK
	select SMEM
	select OF_CONTROL
	imply CMD_DM

config ARCH_KEYSTONE
	bool "TI Keystone"
	select CMD_POWEROFF
	select CPU_V7A
	select DDR_SPD
	select SUPPORT_SPL
	select SYS_ARCH_TIMER
	select SYS_THUMB_BUILD
	imply CMD_MTDPARTS
	imply CMD_SAVES
	imply FIT

config ARCH_K3
	bool "Texas Instruments' K3 Architecture"
	select SPL
	select SUPPORT_SPL
	select FIT

config ARCH_OMAP2PLUS
	bool "TI OMAP2+"
	select CPU_V7A
	select GPIO_EXTRA_HEADER
	select SPL_BOARD_INIT if SPL
	select SPL_STACK_R if SPL
	select SUPPORT_SPL
	imply TI_SYSC if DM && OF_CONTROL
	imply FIT
	imply SPL_SEPARATE_BSS

config ARCH_MESON
	bool "Amlogic Meson"
	select GPIO_EXTRA_HEADER
	imply DISTRO_DEFAULTS
	imply DM_RNG
	help
	  Support for the Meson SoC family developed by Amlogic Inc.,
	  targeted at media players and tablet computers. We currently
	  support the S905 (GXBaby) 64-bit SoC.

config ARCH_MEDIATEK
	bool "MediaTek SoCs"
	select DM
	select GPIO_EXTRA_HEADER
	select OF_CONTROL
	select SPL_DM if SPL
	select SPL_LIBCOMMON_SUPPORT if SPL
	select SPL_LIBGENERIC_SUPPORT if SPL
	select SPL_OF_CONTROL if SPL
	select SUPPORT_SPL
	help
	  Support for the MediaTek SoCs family developed by MediaTek Inc.
	  Please refer to doc/README.mediatek for more information.

config ARCH_LPC32XX
	bool "NXP LPC32xx platform"
	select CPU_ARM926EJS
	select DM
	select DM_GPIO
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	select SPL_DM if SPL
	select SUPPORT_SPL
	imply CMD_DM

config ARCH_IMX8
	bool "NXP i.MX8 platform"
	select ARM64
	select SYS_FSL_HAS_SEC
	select SYS_FSL_SEC_COMPAT_4
	select SYS_FSL_SEC_LE
	select DM
	select DM_EVENT
	select GPIO_EXTRA_HEADER
	select MACH_IMX
	select OF_CONTROL
	select ENABLE_ARM_SOC_BOOT0_HOOK

config ARCH_IMX8M
	bool "NXP i.MX8M platform"
	select ARM64
	select GPIO_EXTRA_HEADER
	select MACH_IMX
	select SYS_FSL_HAS_SEC
	select SYS_FSL_SEC_COMPAT_4
	select SYS_FSL_SEC_LE
	select SYS_I2C_MXC
	select DM
	select DM_EVENT if CLK
	select SUPPORT_SPL
	imply CMD_DM

config ARCH_IMX8ULP
	bool "NXP i.MX8ULP platform"
	select ARM64
	select DM
	select DM_EVENT
	select MACH_IMX
	select OF_CONTROL
	select SUPPORT_SPL
	select GPIO_EXTRA_HEADER
	select MISC
	select IMX_SENTINEL
	imply CMD_DM

config ARCH_IMX9
	bool "NXP i.MX9 platform"
	select ARM64
	select DM
	select DM_EVENT
	select MACH_IMX
	select SUPPORT_SPL
	select GPIO_EXTRA_HEADER
	select MISC
	select IMX_SENTINEL
	imply CMD_DM

config ARCH_IMXRT
	bool "NXP i.MXRT platform"
	select CPU_V7M
	select DM
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	select MACH_IMX
	select SUPPORT_SPL
	imply CMD_DM

config ARCH_MX23
	bool "NXP i.MX23 family"
	select CPU_ARM926EJS
	select GPIO_EXTRA_HEADER
	select MACH_IMX
	select PL011_SERIAL
	select SUPPORT_SPL

config ARCH_MX28
	bool "NXP i.MX28 family"
	select CPU_ARM926EJS
	select GPIO_EXTRA_HEADER
	select PL011_SERIAL
	select MACH_IMX
	select SUPPORT_SPL

config ARCH_MX31
	bool "NXP i.MX31 family"
	select CPU_ARM1136
	select GPIO_EXTRA_HEADER
	select MACH_IMX

config ARCH_MX7ULP
	bool "NXP MX7ULP"
	select BOARD_POSTCLK_INIT
	select CPU_V7A
	select GPIO_EXTRA_HEADER
	select MACH_IMX
	select SYS_FSL_HAS_SEC
	select SYS_FSL_SEC_COMPAT_4
	select SYS_FSL_SEC_LE
	select ROM_UNIFIED_SECTIONS
	imply MXC_GPIO
	imply SYS_THUMB_BUILD

config ARCH_MX7
	bool "Freescale MX7"
	select ARCH_MISC_INIT
	select CPU_V7A
	select GPIO_EXTRA_HEADER
	select MACH_IMX
	select MXC_GPT_HCLK
	select SYS_FSL_HAS_SEC
	select SYS_FSL_SEC_COMPAT_4
	select SYS_FSL_SEC_LE
	imply BOARD_EARLY_INIT_F
	imply MXC_GPIO
	imply SYS_THUMB_BUILD

config ARCH_MX6
	bool "Freescale MX6"
	select BOARD_POSTCLK_INIT
	select CPU_V7A
	select GPIO_EXTRA_HEADER
	select MACH_IMX
	select MXC_GPT_HCLK
	select SYS_FSL_HAS_SEC
	select SYS_FSL_SEC_COMPAT_4
	select SYS_FSL_SEC_LE
	select SYS_L2_PL310 if !SYS_L2CACHE_OFF
	imply MXC_GPIO
	imply SYS_THUMB_BUILD
	imply SPL_SEPARATE_BSS

config ARCH_MX5
	bool "Freescale MX5"
	select BOARD_EARLY_INIT_F
	select CPU_V7A
	select GPIO_EXTRA_HEADER
	select MACH_IMX
	imply MXC_GPIO

config ARCH_NEXELL
	bool "Nexell S5P4418/S5P6818 SoC"
	select ENABLE_ARM_SOC_BOOT0_HOOK
	select DM
	select GPIO_EXTRA_HEADER

config ARCH_NPCM
	bool "Support Nuvoton SoCs"
	select DM
	select OF_CONTROL
	imply CMD_DM

config ARCH_APPLE
	bool "Apple SoCs"
	select ARM64
	select CLK
	select CMD_PCI
	select CMD_USB
	select DM
	select DM_GPIO
	select DM_KEYBOARD
	select DM_MAILBOX
	select DM_RESET
	select DM_SERIAL
	select DM_SPI
	select DM_USB
	select VIDEO
	select IOMMU
	select LINUX_KERNEL_IMAGE_HEADER
	select OF_BOARD_SETUP
	select OF_CONTROL
	select PCI
	select PINCTRL
	select POSITION_INDEPENDENT
	select POWER_DOMAIN
	select REGMAP
	select SPI
	select SYSCON
	select SYSRESET
	select SYSRESET_WATCHDOG
	select SYSRESET_WATCHDOG_AUTO
	select USB
	imply CMD_DM
	imply CMD_GPT
	imply DISTRO_DEFAULTS
	imply OF_HAS_PRIOR_STAGE

config ARCH_OWL
	bool "Actions Semi OWL SoCs"
	select DM
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	select OWL_SERIAL
	select CLK
	select CLK_OWL
	select OF_CONTROL
	select SYS_RELOC_GD_ENV_ADDR
	imply CMD_DM

config ARCH_QEMU
	bool "QEMU Virtual Platform"
	select DM
	select DM_SERIAL
	select OF_CONTROL
	select PL01X_SERIAL
	imply CMD_DM
	imply DM_RNG
	imply DM_RTC
	imply RTC_PL031
	imply OF_HAS_PRIOR_STAGE

config ARCH_RMOBILE
	bool "Renesas ARM SoCs"
	select DM
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	imply BOARD_EARLY_INIT_F
	imply CMD_DM
	imply FAT_WRITE
	imply SYS_THUMB_BUILD
	imply ARCH_MISC_INIT if DISPLAY_CPUINFO

config ARCH_SNAPDRAGON
	bool "Qualcomm Snapdragon SoCs"
	select ARM64
	select DM
	select DM_GPIO
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	select MSM_SMEM
	select OF_CONTROL
	select OF_SEPARATE
	select SMEM
	select SPMI
	imply CMD_DM

config ARCH_SOCFPGA
	bool "Altera SOCFPGA family"
	select ARCH_EARLY_INIT_R
	select ARCH_MISC_INIT if !TARGET_SOCFPGA_ARRIA10
	select ARM64 if TARGET_SOCFPGA_SOC64
	select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
	select DM
	select DM_SERIAL
	select GICV2
	select GPIO_EXTRA_HEADER
	select ENABLE_ARM_SOC_BOOT0_HOOK if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
	select OF_CONTROL
	select SPL_DM_RESET if DM_RESET
	select SPL_DM_SERIAL
	select SPL_LIBCOMMON_SUPPORT
	select SPL_LIBGENERIC_SUPPORT
	select SPL_OF_CONTROL
	select SPL_SEPARATE_BSS if TARGET_SOCFPGA_SOC64
	select SPL_SERIAL
	select SPL_SYSRESET
	select SPL_WATCHDOG
	select SUPPORT_SPL
	select SYS_NS16550
	select SYS_THUMB_BUILD if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
	select SYSRESET
	select SYSRESET_SOCFPGA if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
	select SYSRESET_SOCFPGA_SOC64 if TARGET_SOCFPGA_SOC64
	imply CMD_DM
	imply CMD_MTDPARTS
	imply CRC32_VERIFY
	imply DM_SPI
	imply DM_SPI_FLASH
	imply FAT_WRITE
	imply SPL
	imply SPL_DM
	imply SPL_DM_SPI
	imply SPL_DM_SPI_FLASH
	imply SPL_LIBDISK_SUPPORT
	imply SPL_MMC
	imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
	imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
	imply SPL_SPI_FLASH_SUPPORT
	imply SPL_SPI
	imply L2X0_CACHE

config ARCH_SUNXI
	bool "Support sunxi (Allwinner) SoCs"
	select BINMAN
	select CMD_GPIO
	select CMD_MMC if MMC
	select CMD_USB if DISTRO_DEFAULTS && USB_HOST
	select CLK
	select DM
	select DM_GPIO
	select DM_I2C if I2C
	select DM_SPI if SPI
	select DM_SPI_FLASH if SPI
	select DM_KEYBOARD
	select DM_MMC if MMC
	select DM_SCSI if SCSI
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	select OF_BOARD_SETUP
	select OF_CONTROL
	select OF_SEPARATE
	select PINCTRL
	select SPECIFY_CONSOLE_INDEX
	select SPL_SEPARATE_BSS if SPL
	select SPL_STACK_R if SPL
	select SPL_SYS_MALLOC_SIMPLE if SPL
	select SPL_SYS_THUMB_BUILD if !ARM64
	select SUNXI_GPIO
	select SYS_NS16550
	select SYS_THUMB_BUILD if !ARM64
	select USB if DISTRO_DEFAULTS
	select USB_KEYBOARD if DISTRO_DEFAULTS && USB_HOST
	select USB_STORAGE if DISTRO_DEFAULTS && USB_HOST
	select SPL_USE_TINY_PRINTF
	select USE_PREBOOT
	select SYS_RELOC_GD_ENV_ADDR
	imply BOARD_LATE_INIT
	imply CMD_DM
	imply CMD_GPT
	imply CMD_UBI if MTD_RAW_NAND
	imply DISTRO_DEFAULTS
	imply FAT_WRITE
	imply FIT
	imply OF_LIBFDT_OVERLAY
	imply PRE_CONSOLE_BUFFER
	imply SPL_GPIO
	imply SPL_LIBCOMMON_SUPPORT
	imply SPL_LIBGENERIC_SUPPORT
	imply SPL_MMC if MMC
	imply SPL_POWER
	imply SPL_SERIAL
	imply SYSRESET
	imply SYSRESET_WATCHDOG
	imply SYSRESET_WATCHDOG_AUTO
	imply USB_GADGET
	imply WDT

config ARCH_U8500
	bool "ST-Ericsson U8500 Series"
	select CPU_V7A
	select DM
	select DM_GPIO
	select DM_MMC if MMC
	select DM_SERIAL
	select DM_USB_GADGET if DM_USB
	select OF_CONTROL
	select SYSRESET
	select TIMER
	imply AB8500_USB_PHY
	imply ARM_PL180_MMCI
	imply CLK
	imply DM_PMIC
	imply DM_RTC
	imply NOMADIK_GPIO
	imply NOMADIK_MTU_TIMER
	imply PHY
	imply PL01X_SERIAL
	imply PMIC_AB8500
	imply RTC_PL031
	imply SYS_THUMB_BUILD
	imply SYSRESET_SYSCON

config ARCH_VERSAL
	bool "Support Xilinx Versal Platform"
	select ARM64
	select CLK
	select DM
	select DM_MMC if MMC
	select DM_SERIAL
	select GICV3
	select OF_CONTROL
	select SOC_DEVICE
	imply BOARD_LATE_INIT
	imply ENV_VARS_UBOOT_RUNTIME_CONFIG

config ARCH_VERSAL_NET
	bool "Support Xilinx Versal NET Platform"
	select ARM64
	select CLK
	select DM
	select DM_MMC if MMC
	select DM_SERIAL
	select OF_CONTROL
	imply BOARD_LATE_INIT
	imply ENV_VARS_UBOOT_RUNTIME_CONFIG

config ARCH_VF610
	bool "Freescale Vybrid"
	select CPU_V7A
	select GPIO_EXTRA_HEADER
	select IOMUX_SHARE_CONF_REG
	select MACH_IMX
	select SYS_FSL_ERRATUM_ESDHC111
	imply CMD_MTDPARTS
	imply MTD_RAW_NAND

config ARCH_ZYNQ
	bool "Xilinx Zynq based platform"
	select ARM_TWD_TIMER
	select CLK
	select CLK_ZYNQ
	select CPU_V7A
	select DEBUG_UART_BOARD_INIT if SPL && DEBUG_UART
	select DM
	select DM_MMC if MMC
	select DM_SERIAL
	select DM_SPI
	select DM_SPI_FLASH
	select OF_CONTROL
	select SPI
	select SPL_BOARD_INIT if SPL
	select SPL_CLK if SPL
	select SPL_DM if SPL
	select SPL_DM_SPI if SPL
	select SPL_DM_SPI_FLASH if SPL
	select SPL_OF_CONTROL if SPL
	select SPL_SEPARATE_BSS if SPL
	select SPL_TIMER if SPL
	select SUPPORT_SPL
	select TIMER
	imply ARCH_EARLY_INIT_R
	imply BOARD_LATE_INIT
	imply CMD_CLK
	imply CMD_DM
	imply CMD_SPL
	imply ENV_VARS_UBOOT_RUNTIME_CONFIG
	imply FAT_WRITE

config ARCH_ZYNQMP_R5
	bool "Xilinx ZynqMP R5 based platform"
	select CLK
	select CPU_V7R
	select DM
	select DM_MMC if MMC
	select DM_SERIAL
	select OF_CONTROL
	imply CMD_DM
	imply DM_USB_GADGET

config ARCH_ZYNQMP
	bool "Xilinx ZynqMP based platform"
	select ARM64
	select CLK
	select DM
	select DEBUG_UART_BOARD_INIT if SPL && DEBUG_UART
	imply DM_MAILBOX
	select DM_MMC if MMC
	select DM_SERIAL
	select DM_SPI if SPI
	select DM_SPI_FLASH if DM_SPI
	imply FIRMWARE
	select GICV2
	select OF_CONTROL
	select SPL_BOARD_INIT if SPL
	select SPL_CLK if SPL
	select SPL_DM if SPL
	select SPL_DM_SPI if SPI && SPL_DM
	select SPL_DM_SPI_FLASH if SPL_DM_SPI
	select SPL_DM_MAILBOX if SPL
	imply SPL_FIRMWARE if SPL
	select SPL_SEPARATE_BSS if SPL
	select SUPPORT_SPL
	imply ZYNQMP_IPI if DM_MAILBOX
	select SOC_DEVICE
	imply BOARD_LATE_INIT
	imply CMD_DM
	imply ENV_VARS_UBOOT_RUNTIME_CONFIG
	imply FAT_WRITE
	imply MP
	imply DM_USB_GADGET
	imply ZYNQMP_GPIO_MODEPIN if DM_GPIO && USB

config ARCH_TEGRA
	bool "NVIDIA Tegra"
	select GPIO_EXTRA_HEADER
	imply DISTRO_DEFAULTS
	imply FAT_WRITE

config ARCH_VEXPRESS64
	bool "Support ARMv8 Arm Ltd. VExpress based boards and models"
	select ARM64
	select DM
	select DM_SERIAL
	select PL01X_SERIAL
	select OF_CONTROL
	select CLK
	select BLK
	select MTD_NOR_FLASH if MTD
	select FLASH_CFI_DRIVER if MTD
	select ENV_IS_IN_FLASH if MTD
	imply DISTRO_DEFAULTS

config TARGET_CORSTONE1000
	bool "Support Corstone1000 Platform"
	select ARM64
	select PL01X_SERIAL
	select DM

config TARGET_TOTAL_COMPUTE
	bool "Support Total Compute Platform"
	select ARM64
	select PL01X_SERIAL
	select DM
	select DM_SERIAL
	select DM_MMC
	select DM_GPIO

config TARGET_LS2080A_EMU
	bool "Support ls2080a_emu"
	select ARCH_LS2080A
	select ARM64
	select ARMV8_MULTIENTRY
	select FSL_DDR_SYNC_REFRESH
	select GPIO_EXTRA_HEADER
	help
	  Support for Freescale LS2080A_EMU platform.
	  The LS2080A Development System (EMULATOR) is a pre-silicon
	  development platform that supports the QorIQ LS2080A
	  Layerscape Architecture processor.

config TARGET_LS1088AQDS
	bool "Support ls1088aqds"
	select ARCH_LS1088A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	select SUPPORT_SPL
	select FSL_DDR_INTERACTIVE if !SD_BOOT
	help
	  Support for NXP LS1088AQDS platform.
	  The LS1088A Development System (QDS) is a high-performance
	  development platform that supports the QorIQ LS1088A
	  Layerscape Architecture processor.

config TARGET_LS2080AQDS
	bool "Support ls2080aqds"
	select ARCH_LS2080A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	select SUPPORT_SPL
	imply SCSI
	imply SCSI_AHCI
	select FSL_DDR_BIST
	select FSL_DDR_INTERACTIVE if !SPL
	help
	  Support for Freescale LS2080AQDS platform.
	  The LS2080A Development System (QDS) is a high-performance
	  development platform that supports the QorIQ LS2080A
	  Layerscape Architecture processor.

config TARGET_LS2080ARDB
	bool "Support ls2080ardb"
	select ARCH_LS2080A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select SUPPORT_SPL
	select FSL_DDR_BIST
	select FSL_DDR_INTERACTIVE if !SPL
	select GPIO_EXTRA_HEADER
	imply SCSI
	imply SCSI_AHCI
	help
	  Support for Freescale LS2080ARDB platform.
	  The LS2080A Reference design board (RDB) is a high-performance
	  development platform that supports the QorIQ LS2080A
	  Layerscape Architecture processor.

config TARGET_LS2081ARDB
	bool "Support ls2081ardb"
	select ARCH_LS2080A
	select ARM64
	select ARMV8_MULTIENTRY
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	select SUPPORT_SPL
	help
	  Support for Freescale LS2081ARDB platform.
	  The LS2081A Reference design board (RDB) is a high-performance
	  development platform that supports the QorIQ LS2081A/LS2041A
	  Layerscape Architecture processor.

config TARGET_LX2160ARDB
	bool "Support lx2160ardb"
	select ARCH_LX2160A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	help
	  Support for NXP LX2160ARDB platform.
	  The lx2160ardb (LX2160A Reference design board (RDB)
	  is a high-performance development platform that supports the
	  QorIQ LX2160A/LX2120A/LX2080A Layerscape Architecture processor.

config TARGET_LX2160AQDS
	bool "Support lx2160aqds"
	select ARCH_LX2160A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	help
	  Support for NXP LX2160AQDS platform.
	  The lx2160aqds (LX2160A QorIQ Development System (QDS)
	  is a high-performance development platform that supports the
	  QorIQ LX2160A/LX2120A/LX2080A Layerscape Architecture processor.

config TARGET_LX2162AQDS
	bool "Support lx2162aqds"
	select ARCH_LX2162A
	select ARCH_MISC_INIT
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	help
	  Support for NXP LX2162AQDS platform.
	  The lx2162aqds support is based on LX2160A Layerscape Architecture processor.

config TARGET_HIKEY
	bool "Support HiKey 96boards Consumer Edition Platform"
	select ARM64
	select DM
	select DM_GPIO
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	select OF_CONTROL
	select PL01X_SERIAL
	select SPECIFY_CONSOLE_INDEX
	imply CMD_DM
	  help
	  Support for HiKey 96boards platform. It features a HI6220
	  SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM.

config TARGET_HIKEY960
	bool "Support HiKey960 96boards Consumer Edition Platform"
	select ARM64
	select DM
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	select OF_CONTROL
	select PL01X_SERIAL
	imply CMD_DM
	  help
	  Support for HiKey960 96boards platform. It features a HI3660
	  SoC, with 4xA73 CPU, 4xA53 CPU, MALI-G71 GPU, and 3GB RAM.

config TARGET_POPLAR
	bool "Support Poplar 96boards Enterprise Edition Platform"
	select ARM64
	select DM
	select DM_SERIAL
	select GPIO_EXTRA_HEADER
	select OF_CONTROL
	select PL01X_SERIAL
	imply CMD_DM
	  help
	  Support for Poplar 96boards EE platform. It features a HI3798cv200
	  SoC, with 4xA53 CPU, 1GB RAM and the high performance Mali T720 GPU
	  making it capable of running any commercial set-top solution based on
	  Linux or Android.

config TARGET_LS1012AQDS
	bool "Support ls1012aqds"
	select ARCH_LS1012A
	select ARM64
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	help
	  Support for Freescale LS1012AQDS platform.
	  The LS1012A Development System (QDS) is a high-performance
	  development platform that supports the QorIQ LS1012A
	  Layerscape Architecture processor.

config TARGET_LS1012ARDB
	bool "Support ls1012ardb"
	select ARCH_LS1012A
	select ARM64
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	imply SCSI
	imply SCSI_AHCI
	help
	  Support for Freescale LS1012ARDB platform.
	  The LS1012A Reference design board (RDB) is a high-performance
	  development platform that supports the QorIQ LS1012A
	  Layerscape Architecture processor.

config TARGET_LS1012A2G5RDB
	bool "Support ls1012a2g5rdb"
	select ARCH_LS1012A
	select ARM64
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	imply SCSI
	help
	  Support for Freescale LS1012A2G5RDB platform.
	  The LS1012A 2G5 Reference design board (RDB) is a high-performance
	  development platform that supports the QorIQ LS1012A
	  Layerscape Architecture processor.

config TARGET_LS1012AFRWY
	bool "Support ls1012afrwy"
	select ARCH_LS1012A
	select ARM64
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	imply SCSI
	imply SCSI_AHCI
	help
	 Support for Freescale LS1012AFRWY platform.
	 The LS1012A FRWY board (FRWY) is a high-performance
	 development platform that supports the QorIQ LS1012A
	 Layerscape Architecture processor.

config TARGET_LS1012AFRDM
	bool "Support ls1012afrdm"
	select ARCH_LS1012A
	select ARM64
	select ARCH_SUPPORT_TFABOOT
	select GPIO_EXTRA_HEADER
	help
	  Support for Freescale LS1012AFRDM platform.
	  The LS1012A Freedom  board (FRDM) is a high-performance
	  development platform that supports the QorIQ LS1012A
	  Layerscape Architecture processor.

config TARGET_LS1028AQDS
	bool "Support ls1028aqds"
	select ARCH_LS1028A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	help
	  Support for Freescale LS1028AQDS platform
	  The LS1028A Development System (QDS) is a high-performance
	  development platform that supports the QorIQ LS1028A
	  Layerscape Architecture processor.

config TARGET_LS1028ARDB
	bool "Support ls1028ardb"
	select ARCH_LS1028A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select GPIO_EXTRA_HEADER
	help
	  Support for Freescale LS1028ARDB platform
	  The LS1028A Development System (RDB) is a high-performance
	  development platform that supports the QorIQ LS1028A
	  Layerscape Architecture processor.

config TARGET_LS1088ARDB
	bool "Support ls1088ardb"
	select ARCH_LS1088A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select SUPPORT_SPL
	select FSL_DDR_INTERACTIVE if !SD_BOOT
	select GPIO_EXTRA_HEADER
	help
	  Support for NXP LS1088ARDB platform.
	  The LS1088A Reference design board (RDB) is a high-performance
	  development platform that supports the QorIQ LS1088A
	  Layerscape Architecture processor.

config TARGET_LS1021AQDS
	bool "Support ls1021aqds"
	select ARCH_LS1021A
	select ARCH_SUPPORT_PSCI
	select BOARD_EARLY_INIT_F
	select BOARD_LATE_INIT
	select CPU_V7A
	select CPU_V7_HAS_NONSEC
	select CPU_V7_HAS_VIRT
	select LS1_DEEP_SLEEP
	select PEN_ADDR_BIG_ENDIAN
	select SUPPORT_SPL
	select SYS_FSL_DDR
	select FSL_DDR_INTERACTIVE
	select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI
	select GPIO_EXTRA_HEADER
	select SPI_FLASH_DATAFLASH if FSL_DSPI || FSL_QSPI
	imply SCSI

config TARGET_LS1021ATWR
	bool "Support ls1021atwr"
	select ARCH_LS1021A
	select ARCH_SUPPORT_PSCI
	select BOARD_EARLY_INIT_F
	select BOARD_LATE_INIT
	select CPU_V7A
	select CPU_V7_HAS_NONSEC
	select CPU_V7_HAS_VIRT
	select LS1_DEEP_SLEEP
	select PEN_ADDR_BIG_ENDIAN
	select SUPPORT_SPL
	select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI
	select GPIO_EXTRA_HEADER
	imply SCSI

config TARGET_PG_WCOM_SELI8
	bool "Support Hitachi-Powergrids SELI8 service unit card"
	select ARCH_LS1021A
	select ARCH_SUPPORT_PSCI
	select BOARD_EARLY_INIT_F
	select BOARD_LATE_INIT
	select CPU_V7A
	select CPU_V7_HAS_NONSEC
	select CPU_V7_HAS_VIRT
	select SYS_FSL_DDR
	select FSL_DDR_INTERACTIVE
	select GPIO_EXTRA_HEADER
	select VENDOR_KM
	imply SCSI
	help
	 Support for Hitachi-Powergrids SELI8 service unit card.
	 SELI8 is a QorIQ LS1021a based service unit card used
	 in XMC20 and FOX615 product families.

config TARGET_PG_WCOM_EXPU1
	bool "Support Hitachi-Powergrids EXPU1 service unit card"
	select ARCH_LS1021A
	select ARCH_SUPPORT_PSCI
	select BOARD_EARLY_INIT_F
	select BOARD_LATE_INIT
	select CPU_V7A
	select CPU_V7_HAS_NONSEC
	select CPU_V7_HAS_VIRT
	select SYS_FSL_DDR
	select FSL_DDR_INTERACTIVE
	select VENDOR_KM
	imply SCSI
	help
	 Support for Hitachi-Powergrids EXPU1 service unit card.
	 EXPU1 is a QorIQ LS1021a based service unit card used
	 in XMC20 and FOX615 product families.

config TARGET_LS1021ATSN
	bool "Support ls1021atsn"
	select ARCH_LS1021A
	select ARCH_SUPPORT_PSCI
	select BOARD_EARLY_INIT_F
	select BOARD_LATE_INIT
	select CPU_V7A
	select CPU_V7_HAS_NONSEC
	select CPU_V7_HAS_VIRT
	select LS1_DEEP_SLEEP
	select SUPPORT_SPL
	select GPIO_EXTRA_HEADER
	imply SCSI

config TARGET_LS1021AIOT
	bool "Support ls1021aiot"
	select ARCH_LS1021A
	select ARCH_SUPPORT_PSCI
	select BOARD_LATE_INIT
	select CPU_V7A
	select CPU_V7_HAS_NONSEC
	select CPU_V7_HAS_VIRT
	select PEN_ADDR_BIG_ENDIAN
	select SUPPORT_SPL
	select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI
	select GPIO_EXTRA_HEADER
	imply SCSI
	help
	  Support for Freescale LS1021AIOT platform.
	  The LS1021A Freescale board (IOT) is a high-performance
	  development platform that supports the QorIQ LS1021A
	  Layerscape Architecture processor.

config TARGET_LS1043AQDS
	bool "Support ls1043aqds"
	select ARCH_LS1043A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_EARLY_INIT_F
	select BOARD_LATE_INIT
	select SUPPORT_SPL
	select FSL_DDR_INTERACTIVE if !SPL
	select FSL_DSPI if !SPL_NO_DSPI
	select DM_SPI_FLASH if FSL_DSPI
	select GPIO_EXTRA_HEADER
	imply SCSI
	imply SCSI_AHCI
	help
	  Support for Freescale LS1043AQDS platform.

config TARGET_LS1043ARDB
	bool "Support ls1043ardb"
	select ARCH_LS1043A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_EARLY_INIT_F
	select BOARD_LATE_INIT
	select SUPPORT_SPL
	select FSL_DSPI if !SPL_NO_DSPI
	select DM_SPI_FLASH if FSL_DSPI
	select GPIO_EXTRA_HEADER
	help
	  Support for Freescale LS1043ARDB platform.

config TARGET_LS1046AQDS
	bool "Support ls1046aqds"
	select ARCH_LS1046A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_EARLY_INIT_F
	select BOARD_LATE_INIT
	select DM_SPI_FLASH if DM_SPI
	select SUPPORT_SPL
	select FSL_DDR_BIST if !SPL
	select FSL_DDR_INTERACTIVE  if !SPL
	select FSL_DDR_INTERACTIVE if !SPL
	select GPIO_EXTRA_HEADER
	imply SCSI
	help
	  Support for Freescale LS1046AQDS platform.
	  The LS1046A Development System (QDS) is a high-performance
	  development platform that supports the QorIQ LS1046A
	  Layerscape Architecture processor.

config TARGET_LS1046ARDB
	bool "Support ls1046ardb"
	select ARCH_LS1046A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_EARLY_INIT_F
	select BOARD_LATE_INIT
	select DM_SPI_FLASH if DM_SPI
	select POWER_MC34VR500
	select SUPPORT_SPL
	select FSL_DDR_BIST
	select FSL_DDR_INTERACTIVE if !SPL
	select GPIO_EXTRA_HEADER
	imply SCSI
	help
	  Support for Freescale LS1046ARDB platform.
	  The LS1046A Reference Design Board (RDB) is a high-performance
	  development platform that supports the QorIQ LS1046A
	  Layerscape Architecture processor.

config TARGET_LS1046AFRWY
	bool "Support ls1046afrwy"
	select ARCH_LS1046A
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_EARLY_INIT_F
	select BOARD_LATE_INIT
	select DM_SPI_FLASH if DM_SPI
	select GPIO_EXTRA_HEADER
	imply SCSI
	help
	  Support for Freescale LS1046AFRWY platform.
	  The LS1046A Freeway Board (FRWY) is a high-performance
	  development platform that supports the QorIQ LS1046A
	  Layerscape Architecture processor.

config TARGET_SL28
	bool "Support sl28"
	select ARCH_LS1028A
	select ARM64
	select ARMV8_MULTIENTRY
	select SUPPORT_SPL
	select BINMAN
	select DM
	select DM_GPIO
	select DM_I2C
	select DM_MMC
	select DM_SPI_FLASH
	select DM_MDIO
	select PCI
	select DM_RNG
	select DM_RTC
	select DM_SCSI
	select DM_SERIAL
	select DM_SPI
	select GPIO_EXTRA_HEADER
	select SPL_DM if SPL
	select SPL_DM_SPI if SPL
	select SPL_DM_SPI_FLASH if SPL
	select SPL_DM_I2C if SPL
	select SPL_DM_MMC if SPL
	select SPL_DM_SERIAL if SPL
	help
	  Support for Kontron SMARC-sAL28 board.

config TARGET_TEN64
	bool "Support ten64"
	select ARCH_LS1088A
	select ARCH_MISC_INIT
	select ARM64
	select ARMV8_MULTIENTRY
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select SUPPORT_SPL
	select FSL_DDR_INTERACTIVE if !SD_BOOT
	select GPIO_EXTRA_HEADER
	help
	  Support for Traverse Technologies Ten64 board, based
	  on NXP LS1088A.

config ARCH_UNIPHIER
	bool "Socionext UniPhier SoCs"
	select BOARD_LATE_INIT
	select DM
	select DM_GPIO
	select DM_I2C
	select DM_MMC
	select DM_MTD
	select DM_RESET
	select DM_SERIAL
	select OF_BOARD_SETUP
	select OF_CONTROL
	select OF_LIBFDT
	select PINCTRL
	select SPL_BOARD_INIT if SPL
	select SPL_DM if SPL
	select SPL_LIBCOMMON_SUPPORT if SPL
	select SPL_LIBGENERIC_SUPPORT if SPL
	select SPL_OF_CONTROL if SPL
	select SPL_PINCTRL if SPL
	select SUPPORT_SPL
	imply CMD_DM
	imply DISTRO_DEFAULTS
	imply FAT_WRITE
	help
	  Support for UniPhier SoC family developed by Socionext Inc.
	  (formerly, System LSI Business Division of Panasonic Corporation)

config ARCH_SYNQUACER
	bool "Socionext SynQuacer SoCs"
	select ARM64
	select DM
	select GIC_V3
	select PSCI_RESET
	select SYSRESET
	select SYSRESET_PSCI
	select OF_CONTROL
	help
	  Support for SynQuacer SoC family developed by Socionext Inc.
	  This SoC is used on 96boards EE DeveloperBox.

config ARCH_STM32
	bool "Support STMicroelectronics STM32 MCU with cortex M"
	select CPU_V7M
	select DM
	select DM_SERIAL
	imply CMD_DM

config ARCH_STI
	bool "Support STMicroelectronics SoCs"
	select BLK
	select CPU_V7A
	select DM
	select DM_MMC
	select DM_RESET
	select DM_SERIAL
	imply CMD_DM
	help
	  Support for STMicroelectronics STiH407/10 SoC family.
	  This SoC is used on Linaro 96Board STiH410-B2260

config ARCH_STM32MP
	bool "Support STMicroelectronics STM32MP Socs with cortex A"
	select ARCH_MISC_INIT
	select ARCH_SUPPORT_TFABOOT
	select BOARD_LATE_INIT
	select CLK
	select DM
	select DM_GPIO
	select DM_RESET
	select DM_SERIAL
	select MISC
	select OF_CONTROL
	select OF_LIBFDT
	select OF_SYSTEM_SETUP
	select PINCTRL
	select REGMAP
	select SYSCON
	select SYSRESET
	select SYS_THUMB_BUILD
	imply SPL_SYSRESET
	imply CMD_DM
	imply CMD_POWEROFF
	imply OF_LIBFDT_OVERLAY
	imply ENV_VARS_UBOOT_RUNTIME_CONFIG
	imply USE_PREBOOT
	imply TIMESTAMP
	help
	  Support for STM32MP SoC family developed by STMicroelectronics,
	  MPUs based on ARM cortex A core
	  U-BOOT is running in DDR, loaded by the First Stage BootLoader (FSBL).
	  FSBL can be TF-A: Trusted Firmware for Cortex A, for trusted boot
	  chain.
	  SPL is the unsecure FSBL for the basic boot chain.

config ARCH_ROCKCHIP
	bool "Support Rockchip SoCs"
	select BLK
	select BINMAN if SPL_OPTEE || SPL
	select DM
	select DM_GPIO
	select DM_I2C
	select DM_MMC
	select DM_PWM
	select DM_REGULATOR
	select DM_SERIAL
	select DM_SPI
	select DM_SPI_FLASH
	select ENABLE_ARM_SOC_BOOT0_HOOK
	select OF_CONTROL
	select SPI
	select SPL_DM if SPL
	select SPL_DM_SPI if SPL
	select SPL_DM_SPI_FLASH if SPL
	select SYS_MALLOC_F
	select SYS_THUMB_BUILD if !ARM64
	imply ADC
	imply CMD_DM
	imply DEBUG_UART_BOARD_INIT
	imply DISTRO_DEFAULTS
	imply FAT_WRITE
	imply SARADC_ROCKCHIP
	imply SPL_SYSRESET
	imply SPL_SYS_MALLOC_SIMPLE
	imply SYS_NS16550
	imply TPL_SYSRESET
	imply USB_FUNCTION_FASTBOOT

config ARCH_OCTEONTX
	bool "Support OcteonTX SoCs"
	select CLK
	select DM
	select GPIO_EXTRA_HEADER
	select ARM64
	select OF_CONTROL
	select OF_LIVE
	select BOARD_LATE_INIT
	select SYS_CACHE_SHIFT_7
	select SYS_PCI_64BIT if PCI
	imply OF_HAS_PRIOR_STAGE

config ARCH_OCTEONTX2
	bool "Support OcteonTX2 SoCs"
	select CLK
	select DM
	select GPIO_EXTRA_HEADER
	select ARM64
	select OF_CONTROL
	select OF_LIVE
	select BOARD_LATE_INIT
	select SYS_CACHE_SHIFT_7
	select SYS_PCI_64BIT if PCI
	imply OF_HAS_PRIOR_STAGE

config TARGET_THUNDERX_88XX
	bool "Support ThunderX 88xx"
	select ARM64
	select GPIO_EXTRA_HEADER
	select OF_CONTROL
	select PL01X_SERIAL
	select SYS_CACHE_SHIFT_7

config ARCH_ASPEED
	bool "Support Aspeed SoCs"
	select DM
	select OF_CONTROL
	imply CMD_DM

config TARGET_DURIAN
	bool "Support Phytium Durian Platform"
	select ARM64
	select GPIO_EXTRA_HEADER
	help
	  Support for durian platform.
	  It has 2GB Sdram, uart and pcie.

config TARGET_POMELO
	bool "Support Phytium Pomelo Platform"
	select ARM64
	select DM
	select AHCI
	select SCSI_AHCI
	select AHCI_PCI
	select BLK
	select PCI
	select DM_PCI
	select SCSI
	select DM_SCSI
	select DM_SERIAL
	imply CMD_PCI
	help
	   Support for pomelo platform.
	   It has 8GB Sdram, uart and pcie.

config TARGET_PRESIDIO_ASIC
	bool "Support Cortina Presidio ASIC Platform"
	select ARM64
	select GICV2

config TARGET_XENGUEST_ARM64
	bool "Xen guest ARM64"
	select ARM64
	select XEN
	select OF_CONTROL
	select LINUX_KERNEL_IMAGE_HEADER
	select XEN_SERIAL
	select SSCANF
	imply OF_HAS_PRIOR_STAGE

config ARCH_GXP
	bool "Support HPE GXP SoCs"
	select DM
	select OF_CONTROL
	imply CMD_DM

endchoice

config SUPPORT_PASSING_ATAGS
	bool "Support pre-devicetree ATAG-based booting"
	depends on !ARM64
	imply SETUP_MEMORY_TAGS
	help
	  Support for booting older Linux kernels, using ATAGs rather than
	  passing a devicetree.  This is option is rarely used, and the
	  semantics are defined at
	  https://www.kernel.org/doc/Documentation/arm/Booting at section 4a.

config SETUP_MEMORY_TAGS
	bool "Pass memory size information via ATAG"
	depends on SUPPORT_PASSING_ATAGS

config CMDLINE_TAG
	bool "Pass Linux kernel cmdline via ATAG"
	depends on SUPPORT_PASSING_ATAGS

config INITRD_TAG
	bool "Pass initrd starting point and size via ATAG"
	depends on SUPPORT_PASSING_ATAGS

config REVISION_TAG
	bool "Pass system revision via ATAG"
	depends on SUPPORT_PASSING_ATAGS

config SERIAL_TAG
	bool "Pass system serial number via ATAG"
	depends on SUPPORT_PASSING_ATAGS

config STATIC_MACH_TYPE
	bool "Statically define the Machine ID number"
	default y if TARGET_DS109 || TARGET_NOKIA_RX51 || TARGET_DS414 || DEFAULT_DEVICE_TREE = "sun7i-a20-icnova-swac"
	help
	  When booting via ATAGs, enable this option if we know the correct
	  machine ID number to use at compile time.  Some systems will be
	  passed the number dynamically by whatever loads U-Boot.

config MACH_TYPE
	int "Machine ID number"
	depends on STATIC_MACH_TYPE
	default 527 if TARGET_DS109
	default 1955 if TARGET_NOKIA_RX51
	default 3036 if TARGET_DS414
	default 4283 if DEFAULT_DEVICE_TREE = "sun7i-a20-icnova-swac"
	help
	  When booting via ATAGs, the machine type must be passed as a number.
	  For the full list see https://www.arm.linux.org.uk/developer/machines

config ARCH_SUPPORT_TFABOOT
	bool

config TFABOOT
	bool "Support for booting from TF-A"
	depends on ARCH_SUPPORT_TFABOOT
	help
	  Some platforms support the setup of secure registers (for instance
	  for CPU errata handling) or provide secure services like PSCI.
	  Those services could also be provided by other firmware parts
	  like TF-A (Trusted Firmware for Cortex-A), in which case U-Boot
	  does not need to (and cannot) execute this code.
	  Enabling this option will make a U-Boot binary that is relying
	  on other firmware layers to provide secure functionality.

config TI_SECURE_DEVICE
	bool "HS Device Type Support"
	depends on ARCH_KEYSTONE || ARCH_OMAP2PLUS || ARCH_K3
	help
	  If a high secure (HS) device type is being used, this config
	  must be set. This option impacts various aspects of the
	  build system (to create signed boot images that can be
	  authenticated) and the code. See the doc/README.ti-secure
	  file for further details.

config SYS_KWD_CONFIG
	string "kwbimage config file path"
	depends on ARCH_KIRKWOOD || ARCH_MVEBU
	default "arch/arm/mach-mvebu/kwbimage.cfg"
	help
	  Path within the source directory to the kwbimage.cfg file to use
	  when packaging the U-Boot image for use.

source "arch/arm/mach-apple/Kconfig"

source "arch/arm/mach-aspeed/Kconfig"

source "arch/arm/mach-at91/Kconfig"

source "arch/arm/mach-bcm283x/Kconfig"

source "arch/arm/mach-bcmbca/Kconfig"

source "arch/arm/mach-bcmstb/Kconfig"

source "arch/arm/mach-davinci/Kconfig"

source "arch/arm/mach-exynos/Kconfig"

source "arch/arm/mach-hpe/gxp/Kconfig"

source "arch/arm/mach-highbank/Kconfig"

source "arch/arm/mach-integrator/Kconfig"

source "arch/arm/mach-ipq40xx/Kconfig"

source "arch/arm/mach-k3/Kconfig"

source "arch/arm/mach-keystone/Kconfig"

source "arch/arm/mach-kirkwood/Kconfig"

source "arch/arm/mach-lpc32xx/Kconfig"

source "arch/arm/mach-mvebu/Kconfig"

source "arch/arm/mach-octeontx/Kconfig"

source "arch/arm/mach-octeontx2/Kconfig"

source "arch/arm/cpu/armv7/ls102xa/Kconfig"

source "arch/arm/mach-imx/mx3/Kconfig"

source "arch/arm/mach-imx/mx5/Kconfig"

source "arch/arm/mach-imx/mx6/Kconfig"

source "arch/arm/mach-imx/mx7/Kconfig"

source "arch/arm/mach-imx/mx7ulp/Kconfig"

source "arch/arm/mach-imx/imx8/Kconfig"

source "arch/arm/mach-imx/imx8m/Kconfig"

source "arch/arm/mach-imx/imx8ulp/Kconfig"

source "arch/arm/mach-imx/imx9/Kconfig"

source "arch/arm/mach-imx/imxrt/Kconfig"

source "arch/arm/mach-imx/mxs/Kconfig"

source "arch/arm/mach-omap2/Kconfig"

source "arch/arm/cpu/armv8/fsl-layerscape/Kconfig"

source "arch/arm/mach-orion5x/Kconfig"

source "arch/arm/mach-owl/Kconfig"

source "arch/arm/mach-rmobile/Kconfig"

source "arch/arm/mach-meson/Kconfig"

source "arch/arm/mach-mediatek/Kconfig"

source "arch/arm/mach-qemu/Kconfig"

source "arch/arm/mach-rockchip/Kconfig"

source "arch/arm/mach-s5pc1xx/Kconfig"

source "arch/arm/mach-snapdragon/Kconfig"

source "arch/arm/mach-socfpga/Kconfig"

source "arch/arm/mach-sti/Kconfig"

source "arch/arm/mach-stm32/Kconfig"

source "arch/arm/mach-stm32mp/Kconfig"

source "arch/arm/mach-sunxi/Kconfig"

source "arch/arm/mach-tegra/Kconfig"

source "arch/arm/mach-u8500/Kconfig"

source "arch/arm/mach-uniphier/Kconfig"

source "arch/arm/cpu/armv7/vf610/Kconfig"

source "arch/arm/mach-zynq/Kconfig"

source "arch/arm/mach-zynqmp/Kconfig"

source "arch/arm/mach-versal/Kconfig"

source "arch/arm/mach-versal-net/Kconfig"

source "arch/arm/mach-zynqmp-r5/Kconfig"

source "arch/arm/cpu/armv7/Kconfig"

source "arch/arm/cpu/armv8/Kconfig"

source "arch/arm/mach-imx/Kconfig"

source "arch/arm/mach-nexell/Kconfig"

source "arch/arm/mach-npcm/Kconfig"

source "board/armltd/total_compute/Kconfig"
source "board/armltd/corstone1000/Kconfig"
source "board/bosch/shc/Kconfig"
source "board/bosch/guardian/Kconfig"
source "board/Marvell/octeontx/Kconfig"
source "board/Marvell/octeontx2/Kconfig"
source "board/armltd/vexpress/Kconfig"
source "board/armltd/vexpress64/Kconfig"
source "board/cortina/presidio-asic/Kconfig"
source "board/broadcom/bcmns3/Kconfig"
source "board/cavium/thunderx/Kconfig"
source "board/eets/pdu001/Kconfig"
source "board/emulation/qemu-arm/Kconfig"
source "board/freescale/ls2080aqds/Kconfig"
source "board/freescale/ls2080ardb/Kconfig"
source "board/freescale/ls1088a/Kconfig"
source "board/freescale/ls1028a/Kconfig"
source "board/freescale/ls1021aqds/Kconfig"
source "board/freescale/ls1043aqds/Kconfig"
source "board/freescale/ls1021atwr/Kconfig"
source "board/freescale/ls1021atsn/Kconfig"
source "board/freescale/ls1021aiot/Kconfig"
source "board/freescale/ls1046aqds/Kconfig"
source "board/freescale/ls1043ardb/Kconfig"
source "board/freescale/ls1046ardb/Kconfig"
source "board/freescale/ls1046afrwy/Kconfig"
source "board/freescale/ls1012aqds/Kconfig"
source "board/freescale/ls1012ardb/Kconfig"
source "board/freescale/ls1012afrdm/Kconfig"
source "board/freescale/lx2160a/Kconfig"
source "board/grinn/chiliboard/Kconfig"
source "board/hisilicon/hikey/Kconfig"
source "board/hisilicon/hikey960/Kconfig"
source "board/hisilicon/poplar/Kconfig"
source "board/isee/igep003x/Kconfig"
source "board/kontron/sl28/Kconfig"
source "board/myir/mys_6ulx/Kconfig"
source "board/samsung/common/Kconfig"
source "board/siemens/common/Kconfig"
source "board/seeed/npi_imx6ull/Kconfig"
source "board/socionext/developerbox/Kconfig"
source "board/st/stv0991/Kconfig"
source "board/tcl/sl50/Kconfig"
source "board/traverse/ten64/Kconfig"
source "board/variscite/dart_6ul/Kconfig"
source "board/vscom/baltos/Kconfig"
source "board/phytium/durian/Kconfig"
source "board/phytium/pomelo/Kconfig"
source "board/xen/xenguest_arm64/Kconfig"

source "arch/arm/Kconfig.debug"

endmenu