| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame^] | 1 | // SPDX-License-Identifier: BSD-3-Clause |
| 2 | /* |
| 3 | * Copyright (c) 2022, Linaro Limited |
| 4 | */ |
| 5 | |
| 6 | #include <dt-bindings/interrupt-controller/irq.h> |
| 7 | #include <dt-bindings/spmi/spmi.h> |
| 8 | |
| 9 | / { |
| 10 | thermal-zones { |
| 11 | pm8550-thermal { |
| 12 | polling-delay-passive = <100>; |
| 13 | polling-delay = <0>; |
| 14 | |
| 15 | thermal-sensors = <&pm8550_temp_alarm>; |
| 16 | |
| 17 | trips { |
| 18 | trip0 { |
| 19 | temperature = <95000>; |
| 20 | hysteresis = <0>; |
| 21 | type = "passive"; |
| 22 | }; |
| 23 | |
| 24 | trip1 { |
| 25 | temperature = <115000>; |
| 26 | hysteresis = <0>; |
| 27 | type = "hot"; |
| 28 | }; |
| 29 | }; |
| 30 | }; |
| 31 | }; |
| 32 | }; |
| 33 | |
| 34 | |
| 35 | &spmi_bus { |
| 36 | pm8550: pmic@1 { |
| 37 | compatible = "qcom,pm8550", "qcom,spmi-pmic"; |
| 38 | reg = <0x1 SPMI_USID>; |
| 39 | #address-cells = <1>; |
| 40 | #size-cells = <0>; |
| 41 | |
| 42 | pm8550_temp_alarm: temp-alarm@a00 { |
| 43 | compatible = "qcom,spmi-temp-alarm"; |
| 44 | reg = <0xa00>; |
| 45 | interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| 46 | #thermal-sensor-cells = <0>; |
| 47 | }; |
| 48 | |
| 49 | pm8550_gpios: gpio@8800 { |
| 50 | compatible = "qcom,pm8550-gpio", "qcom,spmi-gpio"; |
| 51 | reg = <0x8800>; |
| 52 | gpio-controller; |
| 53 | gpio-ranges = <&pm8550_gpios 0 0 12>; |
| 54 | #gpio-cells = <2>; |
| 55 | interrupt-controller; |
| 56 | #interrupt-cells = <2>; |
| 57 | }; |
| 58 | |
| 59 | pm8550_flash: led-controller@ee00 { |
| 60 | compatible = "qcom,pm8550-flash-led", "qcom,spmi-flash-led"; |
| 61 | reg = <0xee00>; |
| 62 | status = "disabled"; |
| 63 | }; |
| 64 | |
| 65 | pm8550_pwm: pwm { |
| 66 | compatible = "qcom,pm8550-pwm", "qcom,pm8350c-pwm"; |
| 67 | |
| 68 | #address-cells = <1>; |
| 69 | #size-cells = <0>; |
| 70 | #pwm-cells = <2>; |
| 71 | |
| 72 | status = "disabled"; |
| 73 | }; |
| 74 | }; |
| 75 | }; |