src/arm/intel/ixp/intel-ixp42x-freecom-fsg-3.dts

// SPDX-License-Identifier: ISC
/*
 * Device Tree file for the Freecom FSG-3 router.
 * This machine is based on IXP425.
 * This device tree is inspired by the board file by Rod Whitby.
 */

/dts-v1/;

#include "intel-ixp42x.dtsi"
#include <dt-bindings/input/input.h>

/ {
	model = "Freecom FSG-3";
	compatible = "freecom,fsg-3", "intel,ixp42x";
	#address-cells = <1>;
	#size-cells = <1>;

	memory@0 {
		/* 64 MB memory */
		device_type = "memory";
		reg = <0x00000000 0x4000000>;
	};

	chosen {
		/* Boot from the first partition on the hard drive */
		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait";
		stdout-path = "uart0:115200n8";
	};

	aliases {
		serial0 = &uart0;
	};

	gpio_keys {
		compatible = "gpio-keys";

		button-sync {
			wakeup-source;
			/* Closest approximation of what the key should do */
			linux,code = <KEY_CONNECT>;
			label = "sync";
			gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
		};
		button-reset {
			wakeup-source;
			linux,code = <KEY_RESTART>;
			label = "reset";
			gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
		};
		button-usb {
			wakeup-source;
			/* Unplug USB, closest approximation of what the key should do */
			linux,code = <KEY_EJECTCD>;
			label = "usb";
			gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
		};
	};

	i2c {
		compatible = "i2c-gpio";
		sda-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		#address-cells = <1>;
		#size-cells = <0>;

		hwmon@28 {
			/*
			 * Temperature sensor and fan control chip.
			 *
			 * TODO: create a proper device tree binding for
			 * the sensor and temperature zone and create a
			 * zone with fan control.
			 */
			compatible = "winbond,w83781d";
			reg = <0x28>;
		};
		rtc@6f {
			compatible = "isil,isl1208";
			reg = <0x6f>;
		};
	};

	soc {
		bus@c4000000 {
			flash@0,0 {
				compatible = "intel,ixp4xx-flash", "cfi-flash";
				bank-width = <2>;
				/* Enable writes on the expansion bus */
				intel,ixp4xx-eb-write-enable = <1>;
				/* 4 MB of Flash mapped in at CS0 */
				reg = <0 0x00000000 0x400000>;

				partitions {
					compatible = "redboot-fis";
					/* Eraseblock at 0x3e0000 */
					fis-index-block = <0x1f>;
				};
			};

			/* Small syscon with some LEDs at CS2 */
			syscon@2,0 {
				compatible = "freecom,fsg-cs2-system-controller", "syscon";
				reg = <2 0x0 0x200>;
				reg-io-width = <2>;
				#address-cells = <1>;
				#size-cells = <1>;
				ranges = <2 0x0 0x0 0x200>;

				led@0,0 {
					compatible = "register-bit-led";
					reg = <0x00 0x02>;
					mask = <0x01>;
					label = "fsg:blue:wlan";
					linux,default-trigger = "wlan";
					default-state = "on";
				};
				led@0,1 {
					compatible = "register-bit-led";
					reg = <0x00 0x02>;
					mask = <0x02>;
					label = "fsg:blue:wan";
					linux,default-trigger = "";
					default-state = "on";
				};
				led@0,2 {
					compatible = "register-bit-led";
					reg = <0x00 0x02>;
					mask = <0x04>;
					label = "fsg:blue:sata";
					linux,default-trigger = "";
					default-state = "on";
				};
				led@0,3 {
					compatible = "register-bit-led";
					reg = <0x00 0x02>;
					mask = <0x04>;
					label = "fsg:blue:usb";
					linux,default-trigger = "";
					default-state = "on";
				};
				led@0,4 {
					compatible = "register-bit-led";
					reg = <0x00 0x02>;
					mask = <0x08>;
					label = "fsg:blue:sync";
					linux,default-trigger = "";
					default-state = "on";
				};
				led@0,5 {
					compatible = "register-bit-led";
					reg = <0x00 0x02>;
					mask = <0x10>;
					label = "fsg:blue:ring";
					linux,default-trigger = "";
					default-state = "on";
				};
			};
		};

		pci@c0000000 {
			status = "okay";

			/*
			 * Written based on the FSG-3 PCI boardfile.
			 * We have slots 12, 13 & 14 (IDSEL) with one IRQ each.
			 */
			#interrupt-cells = <1>;
			interrupt-map-mask = <0xf800 0 0 7>;
			interrupt-map =
			/* IDSEL 12 */
			<0x6000 0 0 1 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 5 */
			<0x6000 0 0 2 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 5 */
			<0x6000 0 0 3 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 5 */
			<0x6000 0 0 4 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 5 */
			/* IDSEL 13 */
			<0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */
			<0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */
			<0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */
			<0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */
			/* IDSEL 14 */
			<0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */
			<0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */
			<0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */
			<0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */
		};

		/* EthB */
		ethernet@c8009000 {
			status = "okay";
			queue-rx = <&qmgr 3>;
			queue-txready = <&qmgr 20>;
			phy-mode = "rgmii";
			phy-handle = <&phy5>;

			mdio {
				#address-cells = <1>;
				#size-cells = <0>;

				phy4: ethernet-phy@4 {
					reg = <4>;
				};

				phy5: ethernet-phy@5 {
					reg = <5>;
				};
			};
		};

		/* EthC */
		ethernet@c800a000 {
			status = "okay";
			queue-rx = <&qmgr 4>;
			queue-txready = <&qmgr 21>;
			phy-mode = "rgmii";
			phy-handle = <&phy4>;
		};
	};
};