| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame^] | 1 | // SPDX-License-Identifier: GPL-2.0 |
| 2 | /dts-v1/; |
| 3 | #include "bcm2835.dtsi" |
| 4 | #include "bcm2835-rpi.dtsi" |
| 5 | #include "bcm2835-rpi-common.dtsi" |
| 6 | #include "bcm283x-rpi-led-deprecated.dtsi" |
| 7 | #include "bcm283x-rpi-smsc9512.dtsi" |
| 8 | #include "bcm283x-rpi-usb-host.dtsi" |
| 9 | |
| 10 | / { |
| 11 | compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835"; |
| 12 | model = "Raspberry Pi Model B rev2"; |
| 13 | |
| 14 | memory@0 { |
| 15 | device_type = "memory"; |
| 16 | reg = <0 0x10000000>; |
| 17 | }; |
| 18 | }; |
| 19 | |
| 20 | &gpio { |
| 21 | /* |
| 22 | * Taken from Raspberry-Pi-Rev-2.0-Model-AB-Schematics.pdf |
| 23 | * RPI00022 sheet 02 |
| 24 | * |
| 25 | * Legend: |
| 26 | * "FOO" = GPIO line named "FOO" on the schematic |
| 27 | * "FOO_N" = GPIO line named "FOO" on schematic, active low |
| 28 | */ |
| 29 | gpio-line-names = "SDA0", |
| 30 | "SCL0", |
| 31 | "SDA1", |
| 32 | "SCL1", |
| 33 | "GPIO_GCLK", |
| 34 | "CAM_CLK", |
| 35 | "LAN_RUN", |
| 36 | "SPI_CE1_N", |
| 37 | "SPI_CE0_N", |
| 38 | "SPI_MISO", |
| 39 | "SPI_MOSI", |
| 40 | "SPI_SCLK", |
| 41 | "", /* GPIO12 */ |
| 42 | "", /* GPIO13 */ |
| 43 | /* Serial port */ |
| 44 | "TXD0", |
| 45 | "RXD0", |
| 46 | "STATUS_LED_N", |
| 47 | "GPIO17", |
| 48 | "GPIO18", |
| 49 | "", /* GPIO19 */ |
| 50 | "", /* GPIO20 */ |
| 51 | "CAM_GPIO", |
| 52 | "GPIO22", |
| 53 | "GPIO23", |
| 54 | "GPIO24", |
| 55 | "GPIO25", |
| 56 | "", /* GPIO26 */ |
| 57 | "GPIO27", |
| 58 | "GPIO28", |
| 59 | "GPIO29", |
| 60 | "GPIO30", |
| 61 | "GPIO31", |
| 62 | "", /* GPIO32 */ |
| 63 | "", /* GPIO33 */ |
| 64 | "", /* GPIO34 */ |
| 65 | "", /* GPIO35 */ |
| 66 | "", /* GPIO36 */ |
| 67 | "", /* GPIO37 */ |
| 68 | "", /* GPIO38 */ |
| 69 | "", /* GPIO39 */ |
| 70 | "PWM0_OUT", |
| 71 | "", /* GPIO41 */ |
| 72 | "", /* GPIO42 */ |
| 73 | "", /* GPIO43 */ |
| 74 | "", /* GPIO44 */ |
| 75 | "PWM1_OUT", |
| 76 | "HDMI_HPD_P", |
| 77 | "SD_CARD_DET", |
| 78 | /* Used by SD Card */ |
| 79 | "SD_CLK_R", |
| 80 | "SD_CMD_R", |
| 81 | "SD_DATA0_R", |
| 82 | "SD_DATA1_R", |
| 83 | "SD_DATA2_R", |
| 84 | "SD_DATA3_R"; |
| 85 | |
| 86 | pinctrl-names = "default"; |
| 87 | pinctrl-0 = <&gpioout &alt0 &i2s_alt2>; |
| 88 | |
| 89 | /* I2S interface */ |
| 90 | i2s_alt2: i2s_alt2 { |
| 91 | brcm,pins = <28 29 30 31>; |
| 92 | brcm,function = <BCM2835_FSEL_ALT2>; |
| 93 | }; |
| 94 | }; |
| 95 | |
| 96 | &hdmi { |
| 97 | hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; |
| 98 | power-domains = <&power RPI_POWER_DOMAIN_HDMI>; |
| 99 | status = "okay"; |
| 100 | }; |
| 101 | |
| 102 | &led_act { |
| 103 | gpios = <&gpio 16 GPIO_ACTIVE_LOW>; |
| 104 | }; |
| 105 | |
| 106 | &pwm { |
| 107 | pinctrl-names = "default"; |
| 108 | pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; |
| 109 | status = "okay"; |
| 110 | }; |
| 111 | |
| 112 | &sdhost { |
| 113 | pinctrl-names = "default"; |
| 114 | pinctrl-0 = <&sdhost_gpio48>; |
| 115 | bus-width = <4>; |
| 116 | status = "okay"; |
| 117 | }; |
| 118 | |
| 119 | &uart0 { |
| 120 | pinctrl-names = "default"; |
| 121 | pinctrl-0 = <&uart0_gpio14>; |
| 122 | status = "okay"; |
| 123 | }; |