| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame^] | 1 | RT5650/RT5645 audio CODEC |
| 2 | |
| 3 | This device supports I2C only. |
| 4 | |
| 5 | Required properties: |
| 6 | |
| 7 | - compatible : One of "realtek,rt5645" or "realtek,rt5650". |
| 8 | |
| 9 | - reg : The I2C address of the device. |
| 10 | |
| 11 | - interrupts : The CODEC's interrupt output. |
| 12 | |
| 13 | - avdd-supply: Power supply for AVDD, providing 1.8V. |
| 14 | |
| 15 | - cpvdd-supply: Power supply for CPVDD, providing 3.5V. |
| 16 | |
| 17 | Optional properties: |
| 18 | |
| 19 | - hp-detect-gpios: |
| 20 | a GPIO spec for the external headphone detect pin. If jd-mode = 0, |
| 21 | we will get the JD status by getting the value of hp-detect-gpios. |
| 22 | |
| 23 | - realtek,in2-differential |
| 24 | Boolean. Indicate MIC2 input are differential, rather than single-ended. |
| 25 | |
| 26 | - realtek,dmic1-data-pin |
| 27 | 0: dmic1 is not used |
| 28 | 1: using IN2P pin as dmic1 data pin |
| 29 | 2: using GPIO6 pin as dmic1 data pin |
| 30 | 3: using GPIO10 pin as dmic1 data pin |
| 31 | 4: using GPIO12 pin as dmic1 data pin |
| 32 | |
| 33 | - realtek,dmic2-data-pin |
| 34 | 0: dmic2 is not used |
| 35 | 1: using IN2N pin as dmic2 data pin |
| 36 | 2: using GPIO5 pin as dmic2 data pin |
| 37 | 3: using GPIO11 pin as dmic2 data pin |
| 38 | |
| 39 | -- realtek,jd-mode : The JD mode of rt5645/rt5650 |
| 40 | 0 : rt5645/rt5650 JD function is not used |
| 41 | 1 : Mode-0 (VDD=3.3V), two port jack detection |
| 42 | 2 : Mode-1 (VDD=3.3V), one port jack detection |
| 43 | 3 : Mode-2 (VDD=1.8V), one port jack detection |
| 44 | |
| 45 | Pins on the device (for linking into audio routes) for RT5645/RT5650: |
| 46 | |
| 47 | * DMIC L1 |
| 48 | * DMIC R1 |
| 49 | * DMIC L2 |
| 50 | * DMIC R2 |
| 51 | * IN1P |
| 52 | * IN1N |
| 53 | * IN2P |
| 54 | * IN2N |
| 55 | * Haptic Generator |
| 56 | * HPOL |
| 57 | * HPOR |
| 58 | * LOUTL |
| 59 | * LOUTR |
| 60 | * PDM1L |
| 61 | * PDM1R |
| 62 | * SPOL |
| 63 | * SPOR |
| 64 | |
| 65 | Example: |
| 66 | |
| 67 | codec: rt5650@1a { |
| 68 | compatible = "realtek,rt5650"; |
| 69 | reg = <0x1a>; |
| 70 | hp-detect-gpios = <&gpio 19 0>; |
| 71 | interrupt-parent = <&gpio>; |
| 72 | interrupts = <7 IRQ_TYPE_EDGE_FALLING>; |
| 73 | realtek,dmic-en = "true"; |
| 74 | realtek,en-jd-func = "true"; |
| 75 | realtek,jd-mode = <3>; |
| 76 | }; |