Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 1 | // SPDX-License-Identifier: GPL-2.0+ |
| 2 | /* |
| 3 | * Copyright 2021 Gateworks Corporation |
| 4 | */ |
| 5 | |
| 6 | #include <common.h> |
| 7 | #include <command.h> |
| 8 | #include <hang.h> |
| 9 | #include <hexdump.h> |
| 10 | #include <i2c.h> |
| 11 | #include <linux/delay.h> |
| 12 | #include <dm/uclass.h> |
| 13 | |
| 14 | #include "gsc.h" |
| 15 | |
| 16 | DECLARE_GLOBAL_DATA_PTR; |
| 17 | |
| 18 | struct venice_board_info som_info; |
| 19 | struct venice_board_info base_info; |
| 20 | char venice_model[32]; |
Tim Harvey | 78b8e07 | 2021-07-27 15:19:39 -0700 | [diff] [blame] | 21 | uint32_t venice_serial; |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 22 | |
| 23 | /* return a mac address from EEPROM info */ |
| 24 | int gsc_getmac(int index, uint8_t *address) |
| 25 | { |
| 26 | int i, j; |
| 27 | u32 maclow, machigh; |
| 28 | u64 mac; |
| 29 | |
| 30 | j = 0; |
| 31 | if (som_info.macno) { |
| 32 | maclow = som_info.mac[5]; |
| 33 | maclow |= som_info.mac[4] << 8; |
| 34 | maclow |= som_info.mac[3] << 16; |
| 35 | maclow |= som_info.mac[2] << 24; |
| 36 | machigh = som_info.mac[1]; |
| 37 | machigh |= som_info.mac[0] << 8; |
| 38 | mac = machigh; |
| 39 | mac <<= 32; |
| 40 | mac |= maclow; |
| 41 | for (i = 0; i < som_info.macno; i++, j++) { |
| 42 | if (index == j) |
| 43 | goto out; |
| 44 | } |
| 45 | } |
| 46 | |
| 47 | maclow = base_info.mac[5]; |
| 48 | maclow |= base_info.mac[4] << 8; |
| 49 | maclow |= base_info.mac[3] << 16; |
| 50 | maclow |= base_info.mac[2] << 24; |
| 51 | machigh = base_info.mac[1]; |
| 52 | machigh |= base_info.mac[0] << 8; |
| 53 | mac = machigh; |
| 54 | mac <<= 32; |
| 55 | mac |= maclow; |
| 56 | for (i = 0; i < base_info.macno; i++, j++) { |
| 57 | if (index == j) |
| 58 | goto out; |
| 59 | } |
| 60 | |
| 61 | return -EINVAL; |
| 62 | |
| 63 | out: |
| 64 | mac += i; |
| 65 | address[0] = (mac >> 40) & 0xff; |
| 66 | address[1] = (mac >> 32) & 0xff; |
| 67 | address[2] = (mac >> 24) & 0xff; |
| 68 | address[3] = (mac >> 16) & 0xff; |
| 69 | address[4] = (mac >> 8) & 0xff; |
| 70 | address[5] = (mac >> 0) & 0xff; |
| 71 | |
| 72 | return 0; |
| 73 | } |
| 74 | |
| 75 | /* System Controller registers */ |
| 76 | enum { |
| 77 | GSC_SC_CTRL0 = 0, |
| 78 | GSC_SC_CTRL1 = 1, |
| 79 | GSC_SC_STATUS = 10, |
| 80 | GSC_SC_FWCRC = 12, |
| 81 | GSC_SC_FWVER = 14, |
| 82 | GSC_SC_WP = 15, |
| 83 | GSC_SC_RST_CAUSE = 16, |
| 84 | GSC_SC_THERM_PROTECT = 19, |
| 85 | }; |
| 86 | |
| 87 | /* System Controller Control1 bits */ |
| 88 | enum { |
| 89 | GSC_SC_CTRL1_WDTIME = 4, /* 1 = 60s timeout, 0 = 30s timeout */ |
| 90 | GSC_SC_CTRL1_WDEN = 5, /* 1 = enable, 0 = disable */ |
| 91 | GSC_SC_CTRL1_BOOT_CHK = 6, /* 1 = enable alt boot check */ |
| 92 | GSC_SC_CTRL1_WDDIS = 7, /* 1 = disable boot watchdog */ |
| 93 | }; |
| 94 | |
| 95 | /* System Controller Interrupt bits */ |
| 96 | enum { |
| 97 | GSC_SC_IRQ_PB = 0, /* Pushbutton switch */ |
| 98 | GSC_SC_IRQ_SECURE = 1, /* Secure Key erase operation complete */ |
| 99 | GSC_SC_IRQ_EEPROM_WP = 2, /* EEPROM write violation */ |
| 100 | GSC_SC_IRQ_GPIO = 4, /* GPIO change */ |
| 101 | GSC_SC_IRQ_TAMPER = 5, /* Tamper detect */ |
| 102 | GSC_SC_IRQ_WATCHDOG = 6, /* Watchdog trip */ |
| 103 | GSC_SC_IRQ_PBLONG = 7, /* Pushbutton long hold */ |
| 104 | }; |
| 105 | |
| 106 | /* System Controller WP bits */ |
| 107 | enum { |
| 108 | GSC_SC_WP_ALL = 0, /* Write Protect All EEPROM regions */ |
| 109 | GSC_SC_WP_BOARDINFO = 1, /* Write Protect Board Info region */ |
| 110 | }; |
| 111 | |
| 112 | /* System Controller Reset Cause */ |
| 113 | enum { |
| 114 | GSC_SC_RST_CAUSE_VIN = 0, |
| 115 | GSC_SC_RST_CAUSE_PB = 1, |
| 116 | GSC_SC_RST_CAUSE_WDT = 2, |
| 117 | GSC_SC_RST_CAUSE_CPU = 3, |
| 118 | GSC_SC_RST_CAUSE_TEMP_LOCAL = 4, |
| 119 | GSC_SC_RST_CAUSE_TEMP_REMOTE = 5, |
| 120 | GSC_SC_RST_CAUSE_SLEEP = 6, |
| 121 | GSC_SC_RST_CAUSE_BOOT_WDT = 7, |
| 122 | GSC_SC_RST_CAUSE_BOOT_WDT_MAN = 8, |
| 123 | GSC_SC_RST_CAUSE_SOFT_PWR = 9, |
| 124 | GSC_SC_RST_CAUSE_MAX = 10, |
| 125 | }; |
| 126 | |
Tim Harvey | d541927 | 2021-07-27 15:19:38 -0700 | [diff] [blame] | 127 | #include <dm/device.h> |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 128 | static struct udevice *gsc_get_dev(int busno, int slave) |
| 129 | { |
Tim Harvey | 7ae30ce | 2021-03-08 13:52:35 -0800 | [diff] [blame] | 130 | struct udevice *dev, *bus; |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 131 | int ret; |
| 132 | |
Tim Harvey | d541927 | 2021-07-27 15:19:38 -0700 | [diff] [blame] | 133 | ret = uclass_get_device_by_seq(UCLASS_I2C, busno, &bus); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 134 | if (ret) { |
Tim Harvey | 7ae30ce | 2021-03-08 13:52:35 -0800 | [diff] [blame] | 135 | printf("GSC : failed I2C%d probe: %d\n", busno, ret); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 136 | return NULL; |
| 137 | } |
Tim Harvey | 7ae30ce | 2021-03-08 13:52:35 -0800 | [diff] [blame] | 138 | ret = dm_i2c_probe(bus, slave, 0, &dev); |
| 139 | if (ret) |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 140 | return NULL; |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 141 | |
| 142 | return dev; |
| 143 | } |
| 144 | |
| 145 | static int gsc_read_eeprom(int bus, int slave, int alen, struct venice_board_info *info) |
| 146 | { |
| 147 | int i; |
| 148 | int chksum; |
| 149 | unsigned char *buf = (unsigned char *)info; |
| 150 | struct udevice *dev; |
| 151 | int ret; |
| 152 | |
| 153 | /* probe device */ |
| 154 | dev = gsc_get_dev(bus, slave); |
| 155 | if (!dev) { |
| 156 | if (slave == GSC_EEPROM_ADDR) |
| 157 | puts("ERROR: Failed to probe EEPROM\n"); |
| 158 | return -ENODEV; |
| 159 | } |
| 160 | |
| 161 | /* read eeprom config section */ |
| 162 | memset(info, 0, sizeof(*info)); |
| 163 | ret = i2c_set_chip_offset_len(dev, alen); |
| 164 | if (ret) { |
| 165 | puts("EEPROM: Failed to set alen\n"); |
| 166 | return ret; |
| 167 | } |
| 168 | ret = dm_i2c_read(dev, 0x00, buf, sizeof(*info)); |
| 169 | if (ret) { |
| 170 | if (slave == GSC_EEPROM_ADDR) |
| 171 | printf("EEPROM: Failed to read EEPROM\n"); |
| 172 | return ret; |
| 173 | } |
| 174 | |
| 175 | /* validate checksum */ |
| 176 | for (chksum = 0, i = 0; i < (int)sizeof(*info) - 2; i++) |
| 177 | chksum += buf[i]; |
| 178 | if ((info->chksum[0] != chksum >> 8) || |
| 179 | (info->chksum[1] != (chksum & 0xff))) { |
Tim Harvey | 18a1f6d | 2021-06-30 17:07:38 -0700 | [diff] [blame] | 180 | printf("EEPROM: I2C%d@0x%02x: Invalid Checksum\n", bus, slave); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 181 | print_hex_dump_bytes("", DUMP_PREFIX_NONE, buf, sizeof(*info)); |
| 182 | memset(info, 0, sizeof(*info)); |
| 183 | return -EINVAL; |
| 184 | } |
| 185 | |
| 186 | /* sanity check valid model */ |
| 187 | if (info->model[0] != 'G' || info->model[1] != 'W') { |
| 188 | printf("EEPROM: I2C%d@0x%02x: Invalid Model in EEPROM\n", bus, slave); |
| 189 | print_hex_dump_bytes("", DUMP_PREFIX_NONE, buf, sizeof(*info)); |
| 190 | memset(info, 0, sizeof(*info)); |
| 191 | return -EINVAL; |
| 192 | } |
| 193 | |
| 194 | return 0; |
| 195 | } |
| 196 | |
| 197 | static const char *gsc_get_rst_cause(struct udevice *dev) |
| 198 | { |
| 199 | static char str[64]; |
| 200 | static const char * const names[] = { |
| 201 | "VIN", |
| 202 | "PB", |
| 203 | "WDT", |
| 204 | "CPU", |
| 205 | "TEMP_L", |
| 206 | "TEMP_R", |
| 207 | "SLEEP", |
| 208 | "BOOT_WDT1", |
| 209 | "BOOT_WDT2", |
| 210 | "SOFT_PWR", |
| 211 | }; |
| 212 | unsigned char reg; |
| 213 | |
| 214 | /* reset cause */ |
| 215 | str[0] = 0; |
| 216 | if (!dm_i2c_read(dev, GSC_SC_RST_CAUSE, ®, 1)) { |
| 217 | if (reg < ARRAY_SIZE(names)) |
| 218 | sprintf(str, "%s", names[reg]); |
| 219 | else |
| 220 | sprintf(str, "0x%02x", reg); |
| 221 | } |
| 222 | |
| 223 | /* thermal protection */ |
| 224 | if (!dm_i2c_read(dev, GSC_SC_THERM_PROTECT, ®, 1)) { |
Tim Harvey | 1110cd5 | 2021-06-30 17:07:42 -0700 | [diff] [blame] | 225 | strcat(str, " Thermal Protection "); |
| 226 | if (reg & BIT(0)) |
| 227 | strcat(str, "Enabled"); |
| 228 | else |
| 229 | strcat(str, "Disabled"); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 230 | } |
| 231 | |
| 232 | return str; |
| 233 | } |
| 234 | |
| 235 | /* display hardware monitor ADC channels */ |
| 236 | int gsc_hwmon(void) |
| 237 | { |
| 238 | const void *fdt = gd->fdt_blob; |
| 239 | struct udevice *dev; |
| 240 | int node, reg, mode, len, val, offset; |
| 241 | const char *label; |
| 242 | u8 buf[2]; |
| 243 | int ret; |
| 244 | |
| 245 | node = fdt_node_offset_by_compatible(fdt, -1, "gw,gsc-adc"); |
| 246 | if (node <= 0) |
| 247 | return node; |
| 248 | |
| 249 | /* probe device */ |
Tim Harvey | d541927 | 2021-07-27 15:19:38 -0700 | [diff] [blame] | 250 | dev = gsc_get_dev(GSC_BUSNO, GSC_HWMON_ADDR); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 251 | if (!dev) { |
| 252 | puts("ERROR: Failed to probe GSC HWMON\n"); |
| 253 | return -ENODEV; |
| 254 | } |
| 255 | |
| 256 | /* iterate over hwmon nodes */ |
| 257 | node = fdt_first_subnode(fdt, node); |
| 258 | while (node > 0) { |
| 259 | reg = fdtdec_get_int(fdt, node, "reg", -1); |
| 260 | mode = fdtdec_get_int(fdt, node, "gw,mode", -1); |
| 261 | offset = fdtdec_get_int(fdt, node, "gw,voltage-offset-microvolt", 0); |
| 262 | label = fdt_stringlist_get(fdt, node, "label", 0, NULL); |
| 263 | |
| 264 | if ((reg == -1) || (mode == -1) || !label) |
| 265 | printf("invalid dt:%s\n", fdt_get_name(fdt, node, NULL)); |
| 266 | |
| 267 | memset(buf, 0, sizeof(buf)); |
| 268 | ret = dm_i2c_read(dev, reg, buf, sizeof(buf)); |
| 269 | if (ret) { |
| 270 | printf("i2c error: %d\n", ret); |
| 271 | continue; |
| 272 | } |
| 273 | val = buf[0] | buf[1] << 8; |
| 274 | if (val >= 0) { |
| 275 | const u32 *div; |
| 276 | int r[2]; |
| 277 | |
| 278 | switch (mode) { |
| 279 | case 0: /* temperature (C*10) */ |
| 280 | if (val > 0x8000) |
| 281 | val -= 0xffff; |
| 282 | printf("%-8s: %d.%ldC\n", label, val / 10, abs(val % 10)); |
| 283 | break; |
| 284 | case 1: /* prescaled voltage */ |
| 285 | if (val != 0xffff) |
| 286 | printf("%-8s: %d.%03dV\n", label, val / 1000, val % 1000); |
| 287 | break; |
| 288 | case 2: /* scaled based on ref volt and resolution */ |
| 289 | val *= 2500; |
| 290 | val /= 1 << 12; |
| 291 | |
| 292 | /* apply pre-scaler voltage divider */ |
| 293 | div = fdt_getprop(fdt, node, "gw,voltage-divider-ohms", &len); |
| 294 | if (div && (len == sizeof(uint32_t) * 2)) { |
| 295 | r[0] = fdt32_to_cpu(div[0]); |
| 296 | r[1] = fdt32_to_cpu(div[1]); |
| 297 | if (r[0] && r[1]) { |
| 298 | val *= (r[0] + r[1]); |
| 299 | val /= r[1]; |
| 300 | } |
| 301 | } |
| 302 | |
| 303 | /* adjust by offset */ |
Tim Harvey | 274db32 | 2021-06-30 17:07:39 -0700 | [diff] [blame] | 304 | val += (offset / 1000); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 305 | |
| 306 | printf("%-8s: %d.%03dV\n", label, val / 1000, val % 1000); |
| 307 | break; |
| 308 | } |
| 309 | } |
| 310 | node = fdt_next_subnode(fdt, node); |
| 311 | } |
| 312 | |
| 313 | return 0; |
| 314 | } |
| 315 | |
| 316 | /* determine BOM revision from model */ |
| 317 | int get_bom_rev(const char *str) |
| 318 | { |
| 319 | int rev_bom = 0; |
| 320 | int i; |
| 321 | |
| 322 | for (i = strlen(str) - 1; i > 0; i--) { |
| 323 | if (str[i] == '-') |
| 324 | break; |
| 325 | if (str[i] >= '1' && str[i] <= '9') { |
| 326 | rev_bom = str[i] - '0'; |
| 327 | break; |
| 328 | } |
| 329 | } |
| 330 | return rev_bom; |
| 331 | } |
| 332 | |
| 333 | /* determine PCB revision from model */ |
| 334 | char get_pcb_rev(const char *str) |
| 335 | { |
| 336 | char rev_pcb = 'A'; |
| 337 | int i; |
| 338 | |
| 339 | for (i = strlen(str) - 1; i > 0; i--) { |
| 340 | if (str[i] == '-') |
| 341 | break; |
| 342 | if (str[i] >= 'A') { |
| 343 | rev_pcb = str[i]; |
| 344 | break; |
| 345 | } |
| 346 | } |
| 347 | return rev_pcb; |
| 348 | } |
| 349 | |
| 350 | /* |
| 351 | * get dt name based on model and detail level: |
| 352 | * |
| 353 | * For boards that are a combination of a SoM plus a Baseboard: |
| 354 | * Venice SoM part numbers are GW70xx where xx is: |
| 355 | * 7000-7019: same PCB with som dt of '0x' |
| 356 | * 7020-7039: same PCB with som dt of '2x' |
| 357 | * 7040-7059: same PCB with som dt of '4x' |
| 358 | * 7060-7079: same PCB with som dt of '6x' |
| 359 | * 7080-7099: same PCB with som dt of '8x' |
| 360 | * Venice Baseboard part numbers are GW7xxx where xxx is: |
| 361 | * 7100-7199: same PCB with base dt of '71xx' |
| 362 | * 7200-7299: same PCB with base dt of '72xx' |
| 363 | * 7300-7399: same PCB with base dt of '73xx' |
| 364 | * 7400-7499: same PCB with base dt of '74xx' |
| 365 | * 7500-7599: same PCB with base dt of '75xx' |
| 366 | * 7600-7699: same PCB with base dt of '76xx' |
| 367 | * 7700-7799: same PCB with base dt of '77xx' |
| 368 | * 7800-7899: same PCB with base dt of '78xx' |
| 369 | * DT name is comprised of: |
| 370 | * gw<base dt>-<som dt>-[base-pcb-rev][base-bom-rev][som-pcb-rev][som-bom-rev] |
| 371 | * |
| 372 | * For board models from 7900-7999 each PCB is unique with its own dt: |
| 373 | * DT name is comprised: |
| 374 | * gw<model>-[pcb-rev][bom-rev] |
| 375 | * |
| 376 | */ |
| 377 | #define snprintfcat(dest, sz, fmt, ...) \ |
| 378 | snprintf((dest) + strlen(dest), (sz) - strlen(dest), fmt, ##__VA_ARGS__) |
| 379 | const char *gsc_get_dtb_name(int level, char *buf, int sz) |
| 380 | { |
Tim Harvey | 1a50e74 | 2022-02-11 10:48:56 -0800 | [diff] [blame] | 381 | #ifdef CONFIG_IMX8MM |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 382 | const char *pre = "imx8mm-venice-gw"; |
Tim Harvey | 1a50e74 | 2022-02-11 10:48:56 -0800 | [diff] [blame] | 383 | #else |
| 384 | const char *pre = "imx8mn-venice-gw"; |
| 385 | #endif |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 386 | int model, rev_pcb, rev_bom; |
| 387 | |
| 388 | model = ((som_info.model[2] - '0') * 1000) |
| 389 | + ((som_info.model[3] - '0') * 100) |
| 390 | + ((som_info.model[4] - '0') * 10) |
| 391 | + (som_info.model[5] - '0'); |
| 392 | rev_pcb = tolower(get_pcb_rev(som_info.model)); |
| 393 | rev_bom = get_bom_rev(som_info.model); |
| 394 | |
| 395 | /* som + baseboard*/ |
| 396 | if (base_info.model[0]) { |
| 397 | /* baseboard id: 7100-7199->71; 7200-7299->72; etc */ |
| 398 | int base = ((base_info.model[2] - '0') * 10) + (base_info.model[3] - '0'); |
| 399 | /* som id: 7000-7019->1; 7020-7039->2; etc */ |
| 400 | int som = ((model % 100) / 20) * 2; |
| 401 | int rev_base_pcb = tolower(get_pcb_rev(base_info.model)); |
| 402 | int rev_base_bom = get_bom_rev(base_info.model); |
| 403 | |
| 404 | snprintf(buf, sz, "%s%2dxx-%dx", pre, base, som); |
| 405 | switch (level) { |
| 406 | case 0: /* full model (ie gw73xx-0x-a1a1) */ |
| 407 | if (rev_base_bom) |
| 408 | snprintfcat(buf, sz, "-%c%d", rev_base_pcb, rev_base_bom); |
| 409 | else |
| 410 | snprintfcat(buf, sz, "-%c", rev_base_pcb); |
| 411 | if (rev_bom) |
| 412 | snprintfcat(buf, sz, "%c%d", rev_pcb, rev_bom); |
| 413 | else |
| 414 | snprintfcat(buf, sz, "%c", rev_pcb); |
| 415 | break; |
| 416 | case 1: /* don't care about SoM revision */ |
| 417 | if (rev_base_bom) |
| 418 | snprintfcat(buf, sz, "-%c%d", rev_base_pcb, rev_base_bom); |
| 419 | else |
| 420 | snprintfcat(buf, sz, "-%c", rev_base_pcb); |
| 421 | snprintfcat(buf, sz, "xx"); |
| 422 | break; |
| 423 | case 2: /* don't care about baseboard revision */ |
| 424 | snprintfcat(buf, sz, "-xx"); |
| 425 | if (rev_bom) |
| 426 | snprintfcat(buf, sz, "%c%d", rev_pcb, rev_bom); |
| 427 | else |
| 428 | snprintfcat(buf, sz, "%c", rev_pcb); |
| 429 | break; |
| 430 | case 3: /* don't care about SoM/baseboard revision */ |
| 431 | break; |
| 432 | default: |
| 433 | return NULL; |
| 434 | } |
| 435 | } else { |
| 436 | snprintf(buf, sz, "%s%04d", pre, model); |
| 437 | switch (level) { |
| 438 | case 0: /* full model wth PCB and BOM revision first (ie gw7901-a1) */ |
| 439 | if (rev_bom) |
| 440 | snprintfcat(buf, sz, "-%c%d", rev_pcb, rev_bom); |
| 441 | else |
| 442 | snprintfcat(buf, sz, "-%c", rev_pcb); |
| 443 | break; |
| 444 | case 1: /* don't care about BOM revision */ |
| 445 | snprintfcat(buf, sz, "-%c", rev_pcb); |
| 446 | break; |
| 447 | case 2: /* don't care about PCB or BOM revision */ |
| 448 | break; |
| 449 | default: |
| 450 | return NULL; |
| 451 | } |
| 452 | } |
| 453 | |
| 454 | return buf; |
| 455 | } |
| 456 | |
| 457 | static int gsc_read(void) |
| 458 | { |
Tim Harvey | 78b8e07 | 2021-07-27 15:19:39 -0700 | [diff] [blame] | 459 | char rev_pcb; |
| 460 | int rev_bom; |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 461 | int ret; |
| 462 | |
Tim Harvey | d541927 | 2021-07-27 15:19:38 -0700 | [diff] [blame] | 463 | ret = gsc_read_eeprom(GSC_BUSNO, GSC_EEPROM_ADDR, 1, &som_info); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 464 | if (ret) { |
| 465 | memset(&som_info, 0, sizeof(som_info)); |
| 466 | return ret; |
| 467 | } |
| 468 | |
| 469 | /* read optional baseboard EEPROM */ |
Tim Harvey | 78b8e07 | 2021-07-27 15:19:39 -0700 | [diff] [blame] | 470 | gsc_read_eeprom(BASEBOARD_EEPROM_BUSNO, BASEBOARD_EEPROM_ADDR, |
| 471 | 2, &base_info); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 472 | |
Tim Harvey | 78b8e07 | 2021-07-27 15:19:39 -0700 | [diff] [blame] | 473 | /* create model strings */ |
| 474 | if (base_info.model[0]) { |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 475 | sprintf(venice_model, "GW%c%c%c%c-%c%c-", |
| 476 | som_info.model[2], /* family */ |
| 477 | base_info.model[3], /* baseboard */ |
| 478 | base_info.model[4], base_info.model[5], /* subload of baseboard */ |
| 479 | som_info.model[4], som_info.model[5]); /* last 2digits of SOM */ |
| 480 | |
| 481 | /* baseboard revision */ |
| 482 | rev_pcb = get_pcb_rev(base_info.model); |
| 483 | rev_bom = get_bom_rev(base_info.model); |
| 484 | if (rev_bom) |
| 485 | sprintf(venice_model + strlen(venice_model), "%c%d", rev_pcb, rev_bom); |
| 486 | else |
| 487 | sprintf(venice_model + strlen(venice_model), "%c", rev_pcb); |
| 488 | /* som revision */ |
| 489 | rev_pcb = get_pcb_rev(som_info.model); |
| 490 | rev_bom = get_bom_rev(som_info.model); |
| 491 | if (rev_bom) |
| 492 | sprintf(venice_model + strlen(venice_model), "%c%d", rev_pcb, rev_bom); |
| 493 | else |
| 494 | sprintf(venice_model + strlen(venice_model), "%c", rev_pcb); |
Tim Harvey | 78b8e07 | 2021-07-27 15:19:39 -0700 | [diff] [blame] | 495 | } else { |
| 496 | strcpy(venice_model, som_info.model); |
| 497 | } |
| 498 | venice_serial = som_info.serial; |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 499 | |
Tim Harvey | 78b8e07 | 2021-07-27 15:19:39 -0700 | [diff] [blame] | 500 | return 0; |
| 501 | } |
| 502 | |
| 503 | static int gsc_info(int verbose) |
| 504 | { |
| 505 | struct udevice *dev; |
| 506 | unsigned char buf[16]; |
| 507 | |
| 508 | printf("Model : %s\n", venice_model); |
| 509 | printf("Serial : %d\n", som_info.serial); |
| 510 | printf("MFGDate : %02x-%02x-%02x%02x\n", |
| 511 | som_info.mfgdate[0], som_info.mfgdate[1], |
| 512 | som_info.mfgdate[2], som_info.mfgdate[3]); |
| 513 | if (base_info.model[0] && verbose > 1) { |
| 514 | printf("SOM : %s %d %02x-%02x-%02x%02x\n", |
| 515 | som_info.model, som_info.serial, |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 516 | som_info.mfgdate[0], som_info.mfgdate[1], |
| 517 | som_info.mfgdate[2], som_info.mfgdate[3]); |
Tim Harvey | 78b8e07 | 2021-07-27 15:19:39 -0700 | [diff] [blame] | 518 | printf("BASE : %s %d %02x-%02x-%02x%02x\n", |
| 519 | base_info.model, base_info.serial, |
| 520 | base_info.mfgdate[0], base_info.mfgdate[1], |
| 521 | base_info.mfgdate[2], base_info.mfgdate[3]); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 522 | } |
| 523 | |
| 524 | /* Display RTC */ |
| 525 | puts("RTC : "); |
Tim Harvey | d541927 | 2021-07-27 15:19:38 -0700 | [diff] [blame] | 526 | dev = gsc_get_dev(GSC_BUSNO, GSC_RTC_ADDR); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 527 | if (!dev) { |
| 528 | puts("Failed to probe GSC RTC\n"); |
| 529 | } else { |
| 530 | dm_i2c_read(dev, 0, buf, 6); |
| 531 | printf("%d\n", buf[0] | buf[1] << 8 | buf[2] << 16 | buf[3] << 24); |
| 532 | } |
| 533 | |
Tim Harvey | d57a36f | 2021-08-18 15:24:27 -0700 | [diff] [blame] | 534 | /* Display hwmon */ |
| 535 | gsc_hwmon(); |
| 536 | |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 537 | return 0; |
| 538 | } |
| 539 | |
| 540 | int gsc_init(int quiet) |
| 541 | { |
| 542 | unsigned char buf[16]; |
| 543 | struct udevice *dev; |
| 544 | int ret; |
| 545 | |
| 546 | /* |
| 547 | * On a board with a missing/depleted backup battery for GSC, the |
| 548 | * board may be ready to probe the GSC before its firmware is |
| 549 | * running. We will wait here indefinately for the GSC/EEPROM. |
| 550 | */ |
Tim Harvey | 1a50e74 | 2022-02-11 10:48:56 -0800 | [diff] [blame] | 551 | #ifdef CONFIG_IMX8MN |
| 552 | // TODO: |
| 553 | // IMX8MN boots quicker than IMX8MM and exposes issue |
| 554 | // where because GSC I2C state machine isn't running and its |
| 555 | // SCL/SDA are driven low spams i2c errors |
| 556 | // |
| 557 | // Put a loop here that somehow waits for I2C CLK/DAT to be high |
| 558 | mdelay(40); |
| 559 | #endif |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 560 | while (1) { |
| 561 | /* probe device */ |
Tim Harvey | d541927 | 2021-07-27 15:19:38 -0700 | [diff] [blame] | 562 | dev = gsc_get_dev(GSC_BUSNO, GSC_SC_ADDR); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 563 | if (dev) |
| 564 | break; |
| 565 | mdelay(1); |
| 566 | } |
| 567 | |
| 568 | ret = dm_i2c_read(dev, 0, buf, sizeof(buf)); |
| 569 | if (ret) { |
| 570 | puts("ERROR: Failed reading GSC\n"); |
| 571 | return ret; |
| 572 | } |
| 573 | gsc_read(); |
| 574 | |
| 575 | /* banner */ |
| 576 | if (!quiet) { |
| 577 | printf("GSC : v%d 0x%04x", buf[GSC_SC_FWVER], |
| 578 | buf[GSC_SC_FWCRC] | buf[GSC_SC_FWCRC + 1] << 8); |
| 579 | printf(" RST:%s", gsc_get_rst_cause(dev)); |
| 580 | printf("\n"); |
| 581 | gsc_info(1); |
| 582 | } |
| 583 | |
| 584 | if (ret) |
| 585 | hang(); |
| 586 | |
| 587 | return ((16 << som_info.sdram_size) / 1024); |
| 588 | } |
| 589 | |
| 590 | const char *gsc_get_model(void) |
| 591 | { |
| 592 | return venice_model; |
| 593 | } |
| 594 | |
Tim Harvey | 78b8e07 | 2021-07-27 15:19:39 -0700 | [diff] [blame] | 595 | uint32_t gsc_get_serial(void) |
| 596 | { |
| 597 | return venice_serial; |
| 598 | } |
| 599 | |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 600 | #if !(IS_ENABLED(CONFIG_SPL_BUILD)) |
| 601 | static int gsc_sleep(unsigned long secs) |
| 602 | { |
| 603 | unsigned char reg; |
| 604 | struct udevice *dev; |
| 605 | int ret; |
| 606 | |
| 607 | /* probe device */ |
Tim Harvey | d541927 | 2021-07-27 15:19:38 -0700 | [diff] [blame] | 608 | dev = gsc_get_dev(GSC_BUSNO, GSC_SC_ADDR); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 609 | if (!dev) |
| 610 | return -ENODEV; |
| 611 | |
| 612 | printf("GSC Sleeping for %ld seconds\n", secs); |
| 613 | reg = (secs >> 24) & 0xff; |
| 614 | ret = dm_i2c_write(dev, 9, ®, 1); |
| 615 | if (ret) |
| 616 | goto err; |
| 617 | reg = (secs >> 16) & 0xff; |
| 618 | ret = dm_i2c_write(dev, 8, ®, 1); |
| 619 | if (ret) |
| 620 | goto err; |
| 621 | reg = (secs >> 8) & 0xff; |
| 622 | ret = dm_i2c_write(dev, 7, ®, 1); |
| 623 | if (ret) |
| 624 | goto err; |
| 625 | reg = secs & 0xff; |
| 626 | ret = dm_i2c_write(dev, 6, ®, 1); |
| 627 | if (ret) |
| 628 | goto err; |
| 629 | ret = dm_i2c_read(dev, GSC_SC_CTRL1, ®, 1); |
| 630 | if (ret) |
| 631 | goto err; |
| 632 | reg |= (1 << 2); |
| 633 | ret = dm_i2c_write(dev, GSC_SC_CTRL1, ®, 1); |
| 634 | if (ret) |
| 635 | goto err; |
| 636 | reg &= ~(1 << 2); |
| 637 | reg |= 0x3; |
| 638 | ret = dm_i2c_write(dev, GSC_SC_CTRL1, ®, 1); |
| 639 | if (ret) |
| 640 | goto err; |
| 641 | |
| 642 | return 0; |
| 643 | |
| 644 | err: |
| 645 | printf("i2c error\n"); |
| 646 | return ret; |
| 647 | } |
| 648 | |
| 649 | static int gsc_boot_wd_disable(void) |
| 650 | { |
| 651 | u8 reg; |
| 652 | struct udevice *dev; |
| 653 | int ret; |
| 654 | |
| 655 | /* probe device */ |
Tim Harvey | d541927 | 2021-07-27 15:19:38 -0700 | [diff] [blame] | 656 | dev = gsc_get_dev(GSC_BUSNO, GSC_SC_ADDR); |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 657 | if (!dev) |
| 658 | return -ENODEV; |
| 659 | |
| 660 | ret = dm_i2c_read(dev, GSC_SC_CTRL1, ®, 1); |
| 661 | if (ret) |
| 662 | goto err; |
| 663 | reg |= (1 << GSC_SC_CTRL1_WDDIS); |
| 664 | reg &= ~(1 << GSC_SC_CTRL1_BOOT_CHK); |
| 665 | ret = dm_i2c_write(dev, GSC_SC_CTRL1, ®, 1); |
| 666 | if (ret) |
| 667 | goto err; |
| 668 | puts("GSC : boot watchdog disabled\n"); |
| 669 | |
| 670 | return 0; |
| 671 | |
| 672 | err: |
| 673 | printf("i2c error"); |
| 674 | return ret; |
| 675 | } |
| 676 | |
| 677 | static int do_gsc(struct cmd_tbl *cmdtp, int flag, int argc, char * const argv[]) |
| 678 | { |
| 679 | if (argc < 2) |
| 680 | return gsc_info(2); |
| 681 | |
| 682 | if (strcasecmp(argv[1], "sleep") == 0) { |
| 683 | if (argc < 3) |
| 684 | return CMD_RET_USAGE; |
Simon Glass | ff9b903 | 2021-07-24 09:03:30 -0600 | [diff] [blame] | 685 | if (!gsc_sleep(dectoul(argv[2], NULL))) |
Tim Harvey | 256dba0 | 2021-03-02 14:00:21 -0800 | [diff] [blame] | 686 | return CMD_RET_SUCCESS; |
| 687 | } else if (strcasecmp(argv[1], "hwmon") == 0) { |
| 688 | if (!gsc_hwmon()) |
| 689 | return CMD_RET_SUCCESS; |
| 690 | } else if (strcasecmp(argv[1], "wd-disable") == 0) { |
| 691 | if (!gsc_boot_wd_disable()) |
| 692 | return CMD_RET_SUCCESS; |
| 693 | } |
| 694 | |
| 695 | return CMD_RET_USAGE; |
| 696 | } |
| 697 | |
| 698 | U_BOOT_CMD(gsc, 4, 1, do_gsc, "Gateworks System Controller", |
| 699 | "[sleep <secs>]|[hwmon]|[wd-disable]\n"); |
| 700 | #endif |