include/configs/sama5d2_xplained.h

/*
 * Configuration file for the SAMA5D2 Xplained Board.
 *
 * Copyright (C) 2015 Atmel Corporation
 *		      Wenyou Yang <wenyou.yang@atmel.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/* No NOR flash, this definition should put before common header */
#define CONFIG_SYS_NO_FLASH

#include "at91-sama5_common.h"

#define CONFIG_BOARD_EARLY_INIT_F

#define CONFIG_MISC_INIT_R

/* SDRAM */
#define CONFIG_NR_DRAM_BANKS		1
#define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
#define CONFIG_SYS_SDRAM_SIZE		0x20000000

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_INIT_SP_ADDR		0x210000
#else
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif

#define CONFIG_SYS_LOAD_ADDR		0x22000000 /* load address */

/* SerialFlash */
#ifdef CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_BUS		0
#define CONFIG_SF_DEFAULT_CS		0
#define CONFIG_SF_DEFAULT_SPEED		30000000
#endif

/* NAND flash */
#undef CONFIG_CMD_NAND

/* MMC */
#ifdef CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
#endif

/* USB device */
#define CONFIG_USB_ETHER
#define CONFIG_USB_ETH_RNDIS
#define CONFIG_USBNET_MANUFACTURER      "Atmel SAMA5D2 XPlained"

#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
#define CONFIG_DOS_PARTITION
#endif

/* I2C */
#define AT24MAC_ADDR		0x5c
#define AT24MAC_REG		0x9a

/* Ethernet Hardware */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT		20
#define CONFIG_MACB_SEARCH_PHY

/* LCD */

#ifdef CONFIG_LCD
#define LCD_BPP				LCD_COLOR16
#define LCD_OUTPUT_BPP                  24
#define CONFIG_LCD_LOGO
#define CONFIG_LCD_INFO
#define CONFIG_LCD_INFO_BELOW_LOGO
#define CONFIG_SYS_WHITE_ON_BLACK
#define CONFIG_ATMEL_HLCD
#define CONFIG_ATMEL_LCD_RGB565
#endif

#ifdef CONFIG_SYS_USE_MMC

/* bootstrap + u-boot + env in sd card */
#undef FAT_ENV_DEVICE_AND_PART
#undef CONFIG_BOOTCOMMAND

#define FAT_ENV_DEVICE_AND_PART	"1"
#define CONFIG_BOOTCOMMAND	"fatload mmc 1:1 0x21000000 at91-sama5d2_xplained.dtb; " \
				"fatload mmc 1:1 0x22000000 zImage; " \
				"bootz 0x22000000 - 0x21000000"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTARGS \
	"console=ttyS0,115200 earlyprintk root=/dev/mmcblk1p2 rw rootwait"

#endif

/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE		0x200000
#define CONFIG_SPL_MAX_SIZE		0x10000
#define CONFIG_SPL_BSS_START_ADDR	0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE		0x80000
#define CONFIG_SYS_SPL_MALLOC_START	0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x80000

#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_MONITOR_LEN		(512 << 10)

#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT		arch/arm/mach-at91/armv7/u-boot-spl.lds
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"

#elif CONFIG_SYS_USE_SERIALFLASH
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x8000

#endif

#endif