| Igor Opaniuk | 505fb75 | 2020-02-12 17:14:31 +0200 | [diff] [blame] | 1 | .. SPDX-License-Identifier: GPL-2.0+ |
| 2 | |
| 3 | Colibri iMX8QXP V1.0B Module |
| 4 | ============================ |
| 5 | |
| 6 | Quick Start |
| 7 | ----------- |
| 8 | |
| 9 | - Build the ARM trusted firmware binary |
| 10 | - Get scfw_tcm.bin and ahab-container.img |
| 11 | - Build U-Boot |
| 12 | - Load U-Boot binary using uuu |
| 13 | - Flash U-Boot binary into the eMMC |
| 14 | - Boot |
| 15 | |
| 16 | Get and Build the ARM Trusted Firmware |
| 17 | -------------------------------------- |
| 18 | |
| 19 | .. code-block:: bash |
| 20 | |
| 21 | $ git clone -b imx_4.14.78_1.0.0_ga https://source.codeaurora.org/external/imx/imx-atf |
| 22 | $ cd imx-atf/ |
| 23 | $ make PLAT=imx8qxp bl31 |
| 24 | |
| 25 | Get scfw_tcm.bin and ahab-container.img |
| 26 | --------------------------------------- |
| 27 | .. code-block:: bash |
| 28 | |
| 29 | $ wget https://github.com/toradex/meta-fsl-bsp-release/blob/ |
| 30 | toradex-sumo-4.14.78-1.0.0_ga-bringup/imx/meta-bsp/recipes- |
| 31 | bsp/imx-sc-firmware/files/mx8qx-colibri-scfw-tcm.bin?raw=true |
| 32 | $ mv mx8qx-colibri-scfw-tcm.bin\?raw\=true mx8qx-colibri-scfw-tcm.bin |
| 33 | $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin |
| 34 | $ chmod +x firmware-imx-8.0.bin |
| 35 | $ ./firmware-imx-8.0.bin |
| 36 | |
| 37 | Copy the following binaries to the U-Boot folder: |
| 38 | |
| 39 | .. code-block:: bash |
| 40 | |
| 41 | $ cp imx-atf/build/imx8qxp/release/bl31.bin . |
| 42 | $ cp u-boot/u-boot.bin . |
| 43 | |
| 44 | Copy the following firmware to the U-Boot folder: |
| 45 | |
| 46 | .. code-block:: bash |
| 47 | |
| 48 | $ cp firmware-imx-8.0/firmware/seco/ahab-container.img . |
| 49 | |
| 50 | Build U-Boot |
| 51 | ------------ |
| 52 | |
| 53 | .. code-block:: bash |
| 54 | |
| Philippe Schenker | 336720f | 2020-08-28 21:08:05 +0300 | [diff] [blame^] | 55 | $ make colibri-imx8x_defconfig |
| Igor Opaniuk | 505fb75 | 2020-02-12 17:14:31 +0200 | [diff] [blame] | 56 | $ make u-boot-dtb.imx |
| 57 | |
| 58 | Load the U-Boot Binary Using UUU |
| 59 | -------------------------------- |
| 60 | |
| 61 | Get the latest version of the universal update utility (uuu) aka ``mfgtools 3.0``: |
| 62 | |
| 63 | https://community.nxp.com/external-link.jspa?url=https%3A%2F%2Fgithub.com%2FNXPmicro%2Fmfgtools%2Freleases |
| 64 | |
| 65 | Put the module into USB recovery aka serial downloader mode, connect USB device |
| 66 | to your host and execute ``uuu``: |
| 67 | |
| 68 | .. code-block:: bash |
| 69 | |
| 70 | sudo ./uuu u-boot/u-boot-dtb.imx |
| 71 | |
| 72 | Flash the U-Boot Binary into the eMMC |
| 73 | ------------------------------------- |
| 74 | |
| 75 | Burn the ``u-boot-dtb.imx`` binary to the primary eMMC hardware boot area partition: |
| 76 | |
| 77 | .. code-block:: bash |
| 78 | |
| 79 | load mmc 1:1 $loadaddr u-boot-dtb.imx |
| 80 | setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt ${blkcnt} / 0x200 |
| 81 | mmc dev 0 1 |
| 82 | mmc write ${loadaddr} 0x0 ${blkcnt} |