| Joel Johnson | 28bf4ca | 2020-03-23 14:21:32 -0600 | [diff] [blame] | 1 | menu "ClearFog configuration" |
| 2 | depends on TARGET_CLEARFOG |
| 3 | |
| 4 | config TARGET_CLEARFOG_BASE |
| 5 | bool "Use ClearFog Base static configuration" |
| 6 | help |
| 7 | Use the ClearFog Base as the static configuration instead of the |
| 8 | default which uses the ClearFog Pro. |
| 9 | |
| 10 | Runtime board detection is always attempted and used if available. The |
| 11 | static configuration is used as a fallback in cases where runtime |
| 12 | detection is disabled, is not available in hardware, or otherwise fails. |
| 13 | |
| 14 | Only newer revisions of the ClearFog product line support runtime |
| 15 | detection via additional EEPROM hardware. This option enables selecting |
| 16 | the Base variant for older hardware revisions. |
| 17 | |
| Joel Johnson | 165ce6a | 2020-03-23 14:21:34 -0600 | [diff] [blame] | 18 | config CLEARFOG_CON3_SATA |
| 19 | bool "Use CON3 slot in SATA mode" |
| 20 | help |
| 21 | Use the CON3 port with SATA protocol instead of the default PCIe. |
| 22 | The ClearFog port allows usage of either mSATA or miniPCIe |
| 23 | modules, but the desired protocol must be configured at build |
| 24 | time since it affects the SerDes topology layout. |
| 25 | |
| 26 | config CLEARFOG_CON2_SATA |
| 27 | bool "Use CON2 slot in SATA mode" |
| 28 | depends on !TARGET_CLEARFOG_BASE |
| 29 | help |
| 30 | Use the CON2 port with SATA protocol instead of the default PCIe. |
| 31 | The ClearFog port allows usage of either mSATA or miniPCIe |
| 32 | modules, but the desired protocol must be configured at build |
| 33 | time since it affects the SerDes topology layout. |
| 34 | |
| Joel Johnson | 55beee1 | 2020-03-23 14:21:33 -0600 | [diff] [blame] | 35 | config CLEARFOG_SFP_25GB |
| 36 | bool "Enable 2.5 Gbps mode for SFP" |
| 37 | help |
| 38 | Set the SFP module connection to support 2.5 Gbps transfer speed for the |
| 39 | SGMII connection (requires a supporting SFP). By default, transfer speed |
| 40 | of 1.25 Gbps is used, suitable for a more common 1 Gbps SFP module. |
| 41 | |
| Joel Johnson | 31f771c | 2020-03-23 14:21:38 -0600 | [diff] [blame] | 42 | config ENV_SIZE |
| 43 | hex "Environment Size" |
| 44 | default 0x10000 |
| 45 | |
| 46 | config ENV_OFFSET |
| 47 | hex "Environment offset" |
| 48 | default 0xF0000 |
| 49 | |
| Joel Johnson | 4e44d45 | 2020-03-23 14:21:36 -0600 | [diff] [blame] | 50 | config ENV_SECT_SIZE |
| 51 | hex "Environment Sector-Size" |
| 52 | # Use SPI flash erase block size of 4 KiB |
| Dennis Gilmore | cd36dba | 2020-12-08 21:07:38 -0600 | [diff] [blame] | 53 | default 0x1000 if MVEBU_SPL_BOOT_DEVICE_SPI || MVEBU_SPL_BOOT_DEVICE_SATA |
| Joel Johnson | 4e44d45 | 2020-03-23 14:21:36 -0600 | [diff] [blame] | 54 | # Use optimistic 64 KiB erase block, will vary between actual media |
| Dennis Gilmore | cd36dba | 2020-12-08 21:07:38 -0600 | [diff] [blame] | 55 | default 0x10000 if MVEBU_SPL_BOOT_DEVICE_MMC || MVEBU_SPL_BOOT_DEVICE_UART |
| Joel Johnson | 4e44d45 | 2020-03-23 14:21:36 -0600 | [diff] [blame] | 56 | |
| Joel Johnson | 28bf4ca | 2020-03-23 14:21:32 -0600 | [diff] [blame] | 57 | endmenu |